Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
21 novembre 2011
Note importanti relative alla sicurezza
Prevenzione degli infortuni
1. Prima di smontare o assemblare parti della fotocopiatrice o delle periferiche, accertarsi di aver
scollegato il cavo di alimentazione.
2. La presa di alimentazione utilizzata deve trovarsi in prossimità della copiatrice ed essere
facilmente accessibile.
3. Notare che alcuni componenti della fotocopiatrice e il gruppo cassetti carta rimangono sotto
tensione anche quando l’interruttore principale è in posizione OFF.
4. Nel caso in cui sia necessario eseguire un intervento di regolazione o verifica funzionamento con
l'unità alimentata e i coperchi esterni aperti o rimossi, non toccare componenti elettrici o azionati
meccanicamente.
5. Se si inizia un lavoro prima che la fotocopiatrice abbia completato il periodo di riscaldamento o di
inizializzazione, prestare attenzione a non toccare alcun componente elettrico o meccanico. La
macchina inizierà a fare le copie non appena terminate le operazioni di riscaldamento o
inizializzazione.
6. L'interno e le parti metalliche del gruppo fusore raggiungono temperature molto elevate durante il
funzionamento della macchina. Non toccare tali componenti a mani nude.
Il toner e il developer non sono tossici, tuttavia se uno qualsiasi di questi componenti entra
accidentalmente in contatto con gli occhi può provocare irritazioni temporanee. In questi casi, come
primo intervento di soccorso, tentare di rimuovere i residui con collirio oppure risciacquando con
acqua. Se l'irritazione persiste, richiedere assistenza medica.
1
Batterie al litio
Una sostituzione non corretta delle batterie al litio su PCU, scheda controller e unità di memoria
potrebbe causare rischi di esplosione. Sostituire solo con batterie dello stesso tipo o di tipo equivalente
consigliato dal produttore. Smaltire le batterie usate osservando le istruzioni fornite dal produttore.
1. Non incenerire i flaconi di toner o il toner usato. La polvere di toner potrebbe incendiarsi
improvvisamente se esposta a fiamme libere.
2. Smaltire i flaconi di toner usato, il developer e i fotoconduttori organici rispettando le normative
vigenti. (Si tratta di prodotti non tossici.)
3. Smaltire le parti sostituite rispettando le normative vigenti.
4. In caso di stoccaggio delle batterie al litio usate per un successivo smaltimento, non inserire più di
100 batterie in ciascun contenitore sigillato. Lo stoccaggio di un numero maggiore di batterie
senza un adeguato isolamento potrebbe causare reazioni chimiche e il surriscaldamento del
contenitore.
Il Center for Devices and Radiological Health (CDRH) proibisce la riparazione sul posto di unità ottiche
basate sulla tecnologia laser. L'unità di alloggiamento ottica può essere riparata esclusivamente in
fabbrica o in centri che dispongano dell'attrezzatura necessaria. Il sottosistema laser può essere
sostituito sul posto da un tecnico qualificato. Il telaio laser non è riparabile sul posto. Pertanto, qualora
sia necessario sostituire il sottosistema ottico, i tecnici devono inviare al costruttore o ad un centro di
assistenza autorizzato l'intero gruppo telaio-sottosistema laser interessato.
• L'uso di comandi e l'esecuzione di regolazioni o procedure diverse da quelle indicate nel presente
manuale potrebbero provocare l'esposizione a radiazioni nocive.
• Non utilizzare l'aspirapolvere per rimuovere il toner versato (anche usato). Il toner aspirato può
provocare incendi o esplosioni per contatti elettrici all'interno dell'aspirapolvere. Tuttavia, è
possibile utilizzare un aspirapolvere progettato appositamente per evitare esplosioni. Se il toner
finisce sul pavimento, raccoglierlo lentamente e pulire i residui con un panno umido.
2
• Spegnere l'interruttore generale prima di eseguire qualsiasi intervento nella sezione Unità laser. I
raggi laser possono danneggiare gravemente la vista.
ETICHETTA DI ATTENZIONE:
3
Simboli e abbreviazioni
Questo manuale usa diversi simboli e abbreviazioni specifici. Il significato di questi simboli e
abbreviazioni è il seguente:
Anello a clip
Anello ad E
Vite
Connettore
Morsetto
• Il rispetto di queste linee guida garantisce un’operatività sicura e previene il rischio di lesioni.
• Queste informazioni forniscono i suggerimenti e gli avvertimenti necessari per eseguire gli interventi
di assistenza sulla macchina nel migliore dei modi.
4
SOMMARIO
Note importanti relative alla sicurezza.............................................................................................................1
Prevenzione degli infortuni............................................................................................................................1
Condizioni per la salvaguardia della salute................................................................................................1
Rispetto delle normative sulla sicurezza elettrica........................................................................................1
Batterie al litio.................................................................................................................................................2
Avvertenze per uno smaltimento sicuro ed ecologico................................................................................2
Sicurezza del laser.........................................................................................................................................2
Simboli e abbreviazioni.....................................................................................................................................4
1. Informazioni sul prodotto
Specifiche.........................................................................................................................................................11
Configurazione macchina...............................................................................................................................12
Unità principale............................................................................................................................................12
Componenti del sistema..............................................................................................................................13
Panoramica.......................................................................................................................................................15
Disposizione dei componenti......................................................................................................................15
Componenti elettrici.....................................................................................................................................17
Percorso carta..............................................................................................................................................20
Schema azionamento..................................................................................................................................21
Guida per chi conosce già i prodotti precedenti..........................................................................................23
2. Installazione
Precauzioni d'installazione..............................................................................................................................25
Requisiti per l’installazione..............................................................................................................................26
Condizioni ambientali.................................................................................................................................26
Livellamento della macchina.......................................................................................................................27
Requisiti minimi di spazio operativo...........................................................................................................27
Requisiti di alimentazione elettrica.............................................................................................................28
Copiatrice.........................................................................................................................................................29
Controllo accessori......................................................................................................................................29
Apparecchio telefonico opzionale.............................................................................................................34
Gruppo cassetti carta (D661).........................................................................................................................37
Controllo accessori......................................................................................................................................37
Procedura di installazione...........................................................................................................................37
Riscaldatore del gruppo cassetti carta...........................................................................................................40
5
Controllo accessori......................................................................................................................................40
Procedura di installazione (Per una delle PTU installate).........................................................................41
Procedura di installazione (per macchine con due PTU installate).........................................................47
Staffa di giunzione (Collega la copiatrice e il gruppo cassetto carta superiore)..................................54
Staffa di giunzione (Collega i gruppi cassetto carta superiore e inferiore)............................................55
Opzioni del controller......................................................................................................................................56
Panoramica..................................................................................................................................................56
Installazione Wireless LAN (IEEE 802.11a/g)........................................................................................56
Installazione IEEE 1284..............................................................................................................................58
Scheda VM tipo S (D656)..........................................................................................................................59
Gigabit Ethernet...........................................................................................................................................60
Opzione Fax (D655)..................................................................................................................................61
Opzione HDD (D659)................................................................................................................................64
3. Manutenzione preventiva
Tabelle di manutenzione.................................................................................................................................71
Come azzerare il contatore PM.....................................................................................................................72
4. Sostituzione e regolazione
Precauzioni.......................................................................................................................................................73
Informazioni generali..................................................................................................................................73
Batterie al litio...............................................................................................................................................73
Cavi privi di alogeno...................................................................................................................................73
Elettricità statica............................................................................................................................................74
Attrezzi e lubrificanti speciali..........................................................................................................................75
Coperchi esterni e pannello di controllo........................................................................................................76
Coperchio posteriore...................................................................................................................................76
Vassoio copie...............................................................................................................................................76
Pannello di controllo....................................................................................................................................77
Sportello destro............................................................................................................................................79
Vassoio bypass............................................................................................................................................79
Coprioriginali e sensore ARDF...................................................................................................................80
Gruppo scanner...............................................................................................................................................81
Coperchio scanner e vetro di esposizione................................................................................................81
Gruppo LED..................................................................................................................................................81
6
Motore dello scanner..................................................................................................................................82
Sensore posizione di partenza scanner.....................................................................................................83
Fusione..............................................................................................................................................................84
Gruppo fusore..............................................................................................................................................84
Sensore di uscita..........................................................................................................................................85
Unghiette di separazione del rullo fusore..................................................................................................85
Rullo fusore e Lampada di fusione.............................................................................................................86
Interruttore termico e Termistore.................................................................................................................88
Rullo di pressione.........................................................................................................................................89
Controllo bypass striscia di contatto fusore (Controllo striscia NIP)........................................................90
PCU e Lampada di smagnetizzazione...........................................................................................................91
PCU...............................................................................................................................................................91
Lampada di smagnetizzazione..................................................................................................................92
Ventola di sfiato e Motore principale.............................................................................................................94
Ventola di sfiato...........................................................................................................................................94
Motore principale........................................................................................................................................94
Alimentazione carta.........................................................................................................................................96
Rullo di alimentazione carta e Feltrino di frizione.....................................................................................96
Sensore di fine carta....................................................................................................................................97
Sensore di registrazione..............................................................................................................................97
Sensore di fine carta bypass.......................................................................................................................98
Rullo di alimentazione bypass....................................................................................................................99
Frizione del rullo di bypass e Feltrino di frizione....................................................................................100
Alimentazione carta e Frizioni di registrazione......................................................................................101
Trasferimento immagine................................................................................................................................102
Rullo di trasferimento.................................................................................................................................102
Sensore ID e Rullo fronte-retro.................................................................................................................103
Piastra antistatica.......................................................................................................................................105
BICU e Scheda controller.............................................................................................................................106
BICU...........................................................................................................................................................106
Scheda controller......................................................................................................................................107
Altre sostituzioni.............................................................................................................................................112
Motore fronte-retro...................................................................................................................................112
7
Scheda di alimentazione alta tensione ..................................................................................................113
PSU.............................................................................................................................................................114
Solenoide di rilascio contatto...................................................................................................................115
Motore di alimentazione toner.................................................................................................................115
FCU.............................................................................................................................................................116
Gruppo laser..................................................................................................................................................118
Posizione della decalcomania di Attenzione..........................................................................................118
Gruppo laser.............................................................................................................................................119
Gruppo diodo laser e Motore dello specchio poligonale....................................................................120
ARDF...............................................................................................................................................................121
Gruppo ARDF............................................................................................................................................121
Coperchio posteriore ARDF.....................................................................................................................123
Unità di alimentazione originali...............................................................................................................123
Rullo di prelievo.........................................................................................................................................124
Rullo di alimentazione...............................................................................................................................124
Feltrino di frizione......................................................................................................................................126
DFRB...........................................................................................................................................................127
Sensore coperchio superiore ARDF/Sensore presenza originale........................................................127
Motore di azionamento ARDF.................................................................................................................127
Piastra bianca............................................................................................................................................130
Sensore di registrazione...........................................................................................................................131
Regolazione area di copia dell’immagine..................................................................................................133
Stampa.......................................................................................................................................................133
Scansione...................................................................................................................................................135
Regolazione dell’immagine DF................................................................................................................138
5. Istruzioni manutenzione sistema
Programma di assistenza tecnica.................................................................................................................141
Tabelle SP..................................................................................................................................................141
Uso delle Modalità SP e SSP...................................................................................................................141
Uso della modalità SP...................................................................................................................................144
Caricare/Scaricare dati NVRAM...........................................................................................................144
Procedura di aggiornamento del firmware.............................................................................................145
Procedura aggiornamento unità browser...............................................................................................148
8
Gestione errori di aggiornamento firmware...........................................................................................149
Stampa dei Modelli di prova (SP2-109-001).......................................................................................150
Cancella memoria.....................................................................................................................................152
Stampa SMC (SP5-990)..........................................................................................................................153
Analisi errori sensore ID (SP2-220).........................................................................................................154
Tabelle Assistenza Fax..................................................................................................................................155
6. Risoluzione dei problemi
Tabelle SC......................................................................................................................................................157
Riepilogo....................................................................................................................................................157
Descrizione dei codici SC motore............................................................................................................158
Descrizione dei Codici SC........................................................................................................................169
Anomalie dei componenti elettrici................................................................................................................191
Sensore/Interruttore..................................................................................................................................191
Fusibili bruciati...........................................................................................................................................193
Funzione salvataggio su scheda..................................................................................................................194
Panoramica................................................................................................................................................194
Procedura...................................................................................................................................................194
Guida alla Risoluzione dei problemi per il Fax...........................................................................................197
7. Risparmio energetico
Risparmio energetico.....................................................................................................................................199
Modalità risparmio energetico................................................................................................................199
Efficacia del risparmio energetico...........................................................................................................200
Risparmio carta..............................................................................................................................................202
Efficacia della funzione Fronte-retro/Combina.....................................................................................202
9
10
1. Informazioni sul prodotto
Specifiche
Vedere "Appendici" per le seguenti informazioni:
• Specifiche generali
• Formati carta supportati
11
1. Informazioni sul prodotto
Configurazione macchina
Unità principale
12
Configurazione macchina
Unità di collegamento
D660 [B]
FAX
Net Ware D659 [C] Scheda SD per stampa Net Ware tipo 1
13
1. Informazioni sul prodotto
14
Panoramica
Panoramica
Disposizione dei componenti
Unità principale
15
1. Informazioni sul prodotto
ARDF
16
Panoramica
Componenti elettrici
Componenti elettrici 1
9. Sensore di uscita
17
1. Informazioni sul prodotto
Componenti elettrici 2
6. Motore principale
18
Panoramica
ARDF
19
1. Informazioni sul prodotto
Percorso carta
4. Sensore di uscita
6. Sensore di registrazione
20
Panoramica
Schema azionamento
Unità principale
21
1. Informazioni sul prodotto
ARDF
22
Guida per chi conosce già i prodotti precedenti
D127/D128 D115/D116
• I seguenti componenti sono unici per la serie D127/D128. Quando si sostituiscono i seguenti
componenti, utilizzare quelli specificati per ogni modello. NON mischiare le parti seguenti per
D115/D116 e D127/D128. Altrimenti, il funzionamento e la qualità di stampa di entrambe le
macchine non vengono garantite.
1. Unità scansione LED (Gruppo scanner)
2. Gruppo laser (Unità di scrittura)
3. ARDF
4. Rullo pressore (Unità fusione)
5. Bottiglia toner (Unità alimentazione toner)
6. Pannello di controllo
7. Motore unità mobiletto (Unità mobiletto opzionale)
8. Microcomputer a chip singolo (Controllo motore)
23
1. Informazioni sul prodotto
24
2. Installazione
Precauzioni d'installazione
25
2. Installazione
26
Requisiti per l’installazione
Da destra a
Entro 5 mm (0,2") rispetto al piano
sinistra:
27
2. Installazione
• I 750 mm di spazio che si consiglia di lasciare nella parte anteriore sono sufficienti per consentire
al cassetto carta di poter essere estratto. Per consentire ad un operatore di rimanere davanti alla
macchina serve dello spazio aggiuntivo.
• Lo spazio minimo effettivo richiesto sui lati sinistro, posteriore e destro della macchina è di 10 mm,
tuttavia tale spazio non sarebbe sufficiente per aprire il vassoio bypass, lo sportello destro, o il
gruppo ARDF.
• Accertarsi che la presa di corrente non sia lontana dalla macchina e sia facilmente accessibile.
Terminata l'installazione accertarsi che la spina sia bene inserita nella presa di corrente.
• Evitare connessioni multiple sulla stessa presa di corrente.
• Accertarsi di collegare correttamente a terra la macchina.
Tensione in entrata:
28
Copiatrice
Copiatrice
Controllo accessori
Descrizione Q.tà
Procedura di installazione
29
2. Installazione
5. Sollevare la leva [E], premere il nottolino [F] e tirare fuori il porta-flacone [G]. (Non è necessario
tirarlo fuori completamente dalla macchina).
6. Prendere un nuovo flacone di toner ed agitarlo ripetutamente.
30
Copiatrice
• Non girare con forza il flacone del toner sul porta-flacone. Dopo l'accensione, la fotocopiatrice
provvede a posizionare il flacone nella sua sede.
9. Spingere il porta flacone verso l’interno della macchina.
10. Premere il nottolino [J] per bloccare il porta flacone.
31
2. Installazione
13. Estrarre le linguette [M] dal gruppo PCU con una mano, tenendo fermo il gruppo PCU con l'altra
mano.
• Non estrarre le due linguette contemporaneamente, per non danneggiare il gruppo PCU.
14. Chiudere lo sportello anteriore.
15. Estrarre il cassetto carta, e rimuovere il nastro che blocca la guida di appoggio finale nel suo
alloggiamento.
16. Spingere verso il basso la piastra inferiore ed inserire la carta.
17. Regolare le guide laterali. Se la carta da inserire è più corta del formato A4, regolare la guida
finale in posizione corretta.
18. Reinserire il cassetto carta nella fotocopiatrice.
19. Incollare la decalcomania indicante il numero del cassetto e quella indicante il formato carta
appropriato sul cassetto carta [N].
20. Installare le eventuali unità opzionali.
32
Copiatrice
21. Applicare il nucleo di ferrite [O] al cavo di rete [P] quando si collega il cavo.
22. Applicare il nucleo di ferrite alla linea telefonica nello stesso modo descritto al passaggio 21.
23. Collegare la linea telefonica alla presa "LINE".
• La parte terminale del nucleo in ferrite deve trovarsi a circa 9 cm (3,6") dall'estremità del cavo.
(EU, AP, CHN)
24. Collegare il cavo di alimentazione ed accendere la macchina, utilizzando l’interruttore principale
[Q].
25. Se necessario, selezionare la lingua utilizzata sul pannello di controllo ( > Lingua).
Impostazioni interfaccia
Impostazioni copiatrice
33
2. Installazione
Impostazioni fax
Controllo accessori
1 Apparecchio telefonico 1
3 Viti 2
34
Copiatrice
Procedura di installazione
1. Realizzare due fori [A] attraverso cui le viti fissano la staffa dell'apparecchio telefonico alla
macchina principale. (Basta introdurre un cacciavite)
• Staccare il coperchio del vassoio e fare dei fori su di esso. Altrimenti, la PSU verrà danneggiata.
35
2. Installazione
2. Fissare la staffa dell'apparecchio telefonico [B] al lato del coperchio del vassoio. ( x 2)
3. Rimuovere l'etichetta dall'alloggiamento dell'apparecchio telefonico [C].
4. Fissare l'alloggiamento [C] alla staffa di supporto dell'apparecchio telefonico ( x 2).
5. Riattaccare l'etichetta.
6. Mettere l'apparecchio telefonico sull'alloggiamento.
7. Collegare il cavo dell'apparecchio telefonico alla presa "TEL".
36
Gruppo cassetti carta (D661)
Verificare che siano disponibili gli accessori indicati nella tabella seguente.
Descrizione Q.tà
Procedura di installazione
37
2. Installazione
2. Estrarre parzialmente il cassetto carta, rimuovere il nastro e il pezzo di cartone [A], quindi
reinserire il cassetto.
• Quando si installa un secondo gruppo di alimentazione carta, inserire il primo gruppo prima di
mettere la copiatrice sulla coppia delle unità vassoi carta.
4. Rimuovere i cassetti dal gruppo cassetti carta.
5. Caricare la carta nei cassetti. Regolare le guide laterali e posteriori. Se si carica carta di formato
81/2"x 14", rimuovere la guida posteriore e inserirla nel compartimento speciale.
6. Reinserire il cassetto carta nell'unità cassetti carta.
38
Gruppo cassetti carta (D661)
7. Incollare le decalcomanie indicanti il numero del cassetto ed il formato carta, nei punti indicati in
figura.
39
2. Installazione
• Il sistema operativo non funziona quando sono installate più di tre gruppi vassoio carta.
Controllo accessori
Descrizione Q.tà
3. Rondella 7
4. Rondella elastica 7
6. Morsetto (grande) 2
7. Morsetto (medio) 5
8. Morsetto (piccolo) 2
40
Riscaldatore del gruppo cassetti carta
Descrizione Q.tà
9. Supporto filo 1
17. Copri-cavo 1
18. Custodia 1
41
2. Installazione
42
Riscaldatore del gruppo cassetti carta
43
2. Installazione
44
Riscaldatore del gruppo cassetti carta
12. Fissare il cavo del riscaldatore (lungo) [12] al connettore [13] sulla scheda.
13. Fissare il cavo del riscaldatore (lungo) [14]
14. Passare il cavo del riscaldatore (lungo) [12] attraverso il morsetto (grande) [14] verso la parte
interna della copiatrice come illustrato.
45
2. Installazione
• Assicurarsi di far passare il cavo del riscaldatore (lungo) nel foro mantenendo l'estremità del cavo
orizzontalmente. Questo renderà semplice l'inserimento.
21. Far passare la staffa di supporto tra la copiatrice e il cavo del riscaldatore (lungo) tenendo
l'estremità nel foro.
• Per eseguire il passaggio 21 facilmente, assicurarsi di non far passare completamente il cavo del
riscaldatore (lungo) attraverso il foro [19] nel passaggio 20.
22. Fissare il supporto del filo [20] alla staffa di supporto.
23. Fissare il cavo del riscaldatore (lungo) e il cavo di messa a terra (lungo) attraverso il supporto del
filo.
24. Far passare il cavo di messa a terra (lungo) attraverso il foro.
25. Spingere il cavo del riscaldatore (lungo) e il cavo di messa a terra (lungo) verso il lato dell'unità di
alimentazione carta.
26. Fissare il cavo di messa a terra (lungo) [21] ( x 1, rondella x1, rondella elastica x1)
27. Fissare due morsetti (medi) [22] [23].
28. Fissare il morsetto (medio) [24].
29. Collegare il cavo del riscaldatore (lungo) al cavo del riscaldatore (corto).
30. Fissare il cablaggio del riscaldatore con i morsetti come illustrato.
• Assicurarsi che la fascia sul cavo del riscaldatore sia più in alto del morsetto (medio) [22] [24].
46
Riscaldatore del gruppo cassetti carta
1. Se il gruppo cassetti carta è già stato installato, rimuovere sia quello inferiore e che quello superiore
dalla fotocopiatrice.
47
2. Installazione
48
Riscaldatore del gruppo cassetti carta
9. Fissare la protezione [8] sul lato superiore del gruppo di alimentazione carta superiore. ( x 1,
rondella x 1, rondella elastica x 1)
49
2. Installazione
50
Riscaldatore del gruppo cassetti carta
13. Fissare il cavo del riscaldatore (lungo) [13] al connettore [14] sulla scheda.
14. Fissare il morsetto (largo) [15]
15. Portare il cavo del riscaldatore (lungo) [13] attraverso il morsetto (largo) [15] verso il lato interno
della copiatrice come illustrato.
51
2. Installazione
21. Far passare il cavo del riscaldatore (lungo) nel foro [20].
• Assicurarsi di far passare il cavo del riscaldatore (lungo) nel foro mantenendo l'estremità del cavo
orizzontalmente. Questo renderà semplice l'inserimento.
22. Far passare la staffa di supporto tra la copiatrice e il cavo del riscaldatore (lungo) tenendo
l'estremità nel foro.
• Per eseguire il passaggio 22 facilmente, assicurarsi di non passare completamente il cavo del
riscaldatore (lungo) attraverso il foro [20] al passaggio 21.
23. Fissare il supporto del filo [21] alla staffa di supporto.
24. Fissare il cavo del riscaldatore (lungo) e il cavo di messa a terra (lungo) attraverso il supporto del
filo.
25. Far passare il cavo di messa a terra (lungo) attraverso il foro.
26. Spingere il cavo del riscaldatore (lungo) e il cavo di messa a terra (lungo) verso il lato dell'unità di
alimentazione carta.
27. Rimuovere il coperchio del foro [22] dell'unità di alimentazione carta superiore. ( x 1)
52
Riscaldatore del gruppo cassetti carta
28. Fissare il cavo di messa a terra (lungo) [23] ( x 1, rondella x1, rondella elastica x1).
29. Fissare il cavo di messa a terra (corto) tra [24] e [25] attraverso il foro. ( x 2, rondella x2,
rondella elastica x2).
30. Fissare i tre morsetti (medi) [26] [27] [28].
31. Fissare il morsetto (medio) [29] [30].
32. Collegare il cavo del riscaldatore (lungo) al cavo del riscaldatore (medio).
33. Fissare il cablaggio del riscaldatore con i morsetti come illustrato.
• Assicurarsi che la fascia sul cavo del riscaldatore sia più in alto al morsetto (medio) [29] [30].
53
2. Installazione
1. Rimuovere i cassetti.
2. Inserire la staffa di giunzione (anteriore) [1] nello slot come illustrato dalle frecce e serrare ( x 2)
• La freccia rossa nell'immagine illustra il lato convesso del foro per vite. Prestare attenzione a fissare
la staffa correttamente.
54
Riscaldatore del gruppo cassetti carta
• La freccia rossa nell'immagine illustra il lato convesso del foro per vite. Prestare attenzione a fissare
la staffa correttamente.
55
2. Installazione
Questa macchina è dotata di slot per l'installazione di schede di interfaccia opzionali e slot per Schede
SD per il collegamento di interfacce ed applicazioni opzionali.
Accessori
56
Opzioni del controller
1 Adattatore wireless 1
4 Foglio Avvertenze 1
5 Etichetta 1
Procedura di installazione
57
2. Installazione
N° SP Nome Funzione
Channel MAX Imposta il campo massimo delle impostazioni del canale per il
5840 006
(Max canale) paese.
Channel MIN (Min Imposta il campo minimo delle impostazioni del canale
5840 007
canale) consentite per il proprio paese.
Accessori
2 Foglio UL 1
3 Foglio Avvertenze 1
58
Opzioni del controller
Procedura di installazione
Accessori
1 Scheda SD VM 1
2 Decalcomania 1
59
2. Installazione
Installazione
2. Spegnere la macchina.
3. Inserire la scheda SD [A] nello Slot Sd 2 (più in basso).
• Questa scheda SD deve essere inserita nello Slot 2, quello più in basso.
Gigabit Ethernet
60
Opzioni del controller
3. Applicare il nucleo in ferrite [A] all'estremità del cavo d'interfaccia Ethernet, e quindi applicare
l'altro nucleo in ferrite [B] a circa 10 cm dalla fine del cavo d'interfaccia Ethernet.
4. Collegare il cavo d'interfaccia Ethernet alla porta Ethernet Gigabit.
Accertarsi che la macchina sia in grado di riconoscere questa opzione (vedere 'Controllo di tutti i
collegamenti' al termine di questa sezione).
61
2. Installazione
Verifica componenti
1 Unità fax 1
2 Altoparlante 1
3 Foglio isolante 1
10 Conduttore di terra 2
13 Nucleo di ferrite 1
62
Opzioni del controller
Procedura di installazione
1. Coperchio posteriore ( x 5)
2. Fissare l'unità fax [A] alla staffa [B] posizionando il foglio [C] tra l'unità [A] e la staffa [B]. ( x 4)
3. Fissare la guida della staffa [D] come illustrato.
4. Inserire la staffa assemblata nella procedura 2 tra due delle guide come illustra la freccia blu.
5. Fissare l'estremità larga del cablaggio con la banda [E], quindi collegare l'estremità piccola all'unità
fax [A] come mostrano le frecce rosse.
6. Fissare l'altoparlante [F] e il suo connettore all'estremità larga del cablaggio [E].
7. Fissare il nucleo di ferrite [A] sul cablaggio dell'altoparlante a 50mm dall'estremità della scheda
controller. Questo evita che il cavo si incastri nella ventola [B].
63
2. Installazione
Conduttore di terra
Verifica componenti
2 Vite 6
4 Cavo (piccolo) 1
5 Cavo (largo) 1
64
Opzioni del controller
Procedura di installazione
65
2. Installazione
5. Rimuovere tre delle viti e spingere la staffa nella direzione indicata dalla freccia per rimuovere la
scheda [A].
66
Opzioni del controller
6. Fissare l'unità HDD [B] e la scheda di interfaccia SAT [C] con il cavo (piccolo) e il cavo (grande).
7. Installare l'unità HDD [B] e la scheda di interfaccia SAT [C] nella scheda controller ( x 5).
• Assicurarsi di portare i due cavi sulla staffa HDD alla scheda interfaccia SAT [C]. Questo
semplifica l'installazione.
8. Rimontare sulla macchina il coperchio della scatola del controller e il coperchio posteriore.
Accendere la macchina mediante l’interruttore principale.
9. Premere il pulsante “Formatta” visualizzato nel messaggio all'avvio.
10. Spegnere e riaccendere la macchina dopo che il messaggio inviterà a farlo.
67
2. Installazione
1. Accertarsi che le seguenti impostaazioni non siano configurati con i valori predefiniti in fabbrica:
• Password login supervisore
• Nome login amministratore
• Password login amministratore
Se una qualsiasi di queste impostazioni ha il valore predefinito in fabbrica, comunicare al cliente
di cambiare queste impostazioni prima di effettuare la procedura d'installazione.
2. Verificare che l'autenticazione amministratore sia abilitata.
[Impostazioni di Sistema] – [Strumenti amministratore] – [Gestione autenticazione amministratore] -
[Autenticazione ammin. ]
Se questa impostazione è disattivata, comunicare al cliente di riattivarla prima di eseguire la
procedura d'installazione.
3. Accertarsi che gli "Strumenti amministratore" siano abilitati:
[Impostazioni di Sistema] – [Strumenti amministratore] – [Gestione autenticazione amministratore] -
[Impostazioni disponibili]
Se questa impostazione non è selezionata, comunicare al Cliente che essa deve essere
selezionata prima di eseguire la procedura di installazione.
4. Consultare il Manuale della sicurezza per avere maggiori dettagli sull'attivazione delle
applicazioni di sicurezza (Unità di crittografia HDD e Unità di sicurezza con sovrascrittura dati).
Il diagramma di flusso seguente mostra la possibilità di ripristino della crittografia HDD se uno dei
dispositivi collegati alla crittografia HDD è difettoso.
68
Opzioni del controller
Quando si sostituisce la scheda controller con un modello in cui è stata installata l'unità di crittografia
dell'hard disk, è necessario aggiornare il codice di crittografia.
1. Preparare una scheda SD inizializzata.
2. Creare la cartella "restore_key (ripristina_codice)" nella scheda SD.
3. Creare un file "nvram_key.txt" nella cartella "restore_key" della scheda SD.
4. Chiedere ad un amministratore di inserire il codice di crittografia (che è stato stampato in
precedenza dall'utente) nel file "nvram_key.txt".
5. Rimuovere soltanto l'unità hard disk.
6. Riaccendere la macchina.
7. Verificare che il messaggio sul display LCD dica di installare la scheda SD (conservando il codice
di crittografia) nella macchina.
8. Spegnere la macchina utilizzando l’interruttore principale.
9. Inserire la scheda SD contenente il codice di crittografica nello slot 1.
10. Accendere l'interruttore principale e la macchina ripristina automaticamente il codice di crittografia
nella memoria flash della scheda controller.
11. Spegnere l'interruttore principale dopo che la macchina è tornata allo stato normale.
12. Togliere la scheda SD dallo slot 1.
13. Reinstallare l'unità hard disk.
Azzeramento NVRAM
Quando si sostituisce la scheda controller con un modello in cui è stata installata l'unità di crittografia
dell'hard disk e il cliente ha perso il codice di crittografia, è necessario azzerare la NVRAM per
ripristinare l'unità di crittografia dell'hard disk.
1. Preparare una scheda SD inizializzata.
2. Creare la cartella "restore_key (ripristina_codice)" nella scheda SD.
3. Creare un file "nvram_key.txt" nella cartella "restore_key" della scheda SD.
4. Inserire "nvclear" nel file "nvram_key.txt".
5. Riaccendere la macchina.
6. Verificare che il messaggio sul display LCD dica di installare la scheda SD (conservando il codice
di crittografia) nella macchina.
7. Spegnere la macchina utilizzando l’interruttore principale.
8. Inserire la scheda SD contenente "nvclear" nello slot 1.
9. Accendere l'interruttore principale e la macchina ripristina automaticamente il codice di crittografia
nella memoria flash della scheda controller.
69
2. Installazione
10. Spegnere l'interruttore principale dopo che la macchina è tornata allo stato normale.
11. Togliere la scheda SD dallo slot 1.
12. Riaccendere la macchina.
13. Inizializzare la NVRAM (SP5801-001) e l'unità hard disk (SP5832-001) con la modalità SP.
14. L'utente deve abilitare l'unità di crittografia dell'hard disk con uno strumento utente.
70
3. Manutenzione preventiva
Tabelle di manutenzione
Vedere "Appendici" per le informazioni relative a:
• Tabelle MP
71
3. Manutenzione preventiva
72
4. Sostituzione e regolazione
Precauzioni
Informazioni generali
Prima di spegnere l'alimentazione generale, verificare che non vi siano componenti meccanici in
funzione. I componenti meccanici potrebbero fermarsi fuori dalle loro posizioni di partenza se si spegne
l'alimentazione generale mentre si trovano in funzione. Il componente potrebbe rimanere danneggiato
se si cerca di rimuoverlo quando non si trova nella sua posizione di partenza.
Batterie al litio
• Una sostituzione non corretta delle batterie al litio sul controller o sull'unità fax potrebbe causare
rischi di esplosione. Sostituire solo con batterie dello stesso tipo o di tipo equivalente consigliato
dal produttore. Smaltire le batterie usate osservando le istruzioni fornite dal produttore.
Per soddisfare le direttive locali, in questa macchina si dovrebbero usare dei cavi senza alogeni. I cavi
di questo tipo sono rispettosi dell'ambiente, ma non sono più resistenti dei cavi normali. Questi cavi si
potrebbero danneggiare in uno dei seguenti casi:
• Quando il cavo rimane impigliato tra oggetti rigidi quali staffe, viti, schede elettroniche e coperchi
esterni.
• Quando il cavo viene manipolato in modo errato con oggetti rigidi quali staffe, viti, schede
elettroniche e coperchi esterni.
• Quando il cavo è sottoposto ad attrito contro oggetti rigidi quali staffe, viti, schede elettroniche e
coperchi esterni, cacciaviti e unghie.
73
4. Sostituzione e regolazione
Elettricità statica
Toccare sempre una superficie provvista di messa a terra per scaricare l'elettricità statica dalle mani
prima di maneggiare schede SD, schede per circuiti stampati o schede di memoria.
74
Attrezzi e lubrificanti speciali
B6455010 Scheda SD 1
75
4. Sostituzione e regolazione
Vassoio copie
• Accertarsi che i cavi sotto il cassetto copie siano al proprio posto prima di rimontare la copiatrice.
Se questi cavi rimangono incastrati fra il cassetto copie e il coperchio interno, potrebbero
danneggiarsi gravemente.
76
Coperchi esterni e pannello di controllo
Pannello di controllo
77
4. Sostituzione e regolazione
78
Coperchi esterni e pannello di controllo
Sportello destro
Vassoio bypass
79
4. Sostituzione e regolazione
80
Gruppo scanner
Gruppo scanner
Per pulire gli specchi e le lenti, utilizzare un panno per dispositivi ottici oppure del cotone inumidito.
• Il coperchio anteriore dello scanner è fissato da 2 dei ganci come illustrato nell'immagine [1]. Per
rimuovere il coperchio facilmente, spingerlo verso il basso per tenere lontani i ganci.
3. Coperchio dello scanner [B] ( x 7, Gancio)
Gruppo LED
• Non smontare mai il gruppo LED. Il gruppo LED viene regolato con precisione prima della
spedizione.
• Non toccare le viti sul CCD. Il CCD è regolato con precisione prima della spedizione.
• Non rimuovere l'olio di cui è rivestita l'asta della guida. L'olio non è presente sulle parti di ricambio.
81
4. Sostituzione e regolazione
1. Coperchio scanner e vetro di esposizione ( P.81 " Coperchio scanner e vetro di esposizione")
2. Rimuovere la staffa lunga [A] e la staffa dell'asta della guida [B]. ( x 4)
3. Sollevare l'asta della guida [C] come indicato dalla freccia rossa.
4. Estrarre la cinghia [D] come mostra la freccia blu per rilasciare l'unità LED [E] dall'asta della guida.
• Non allentare le viti fissate con vernice che mantengono in posizione le lenti.
• Dopo aver installato nuove lenti, effettuare le regolazioni per la copia ( P.133
"Regolazione area di copia dell’immagine").
82
Gruppo scanner
1. Spingere la molla [A] posizionata sul lato opposto del motore scanner [B] per allentare la cinghia
[C] dall'ingranaggio del motore dello scanner.
2. Rimuovere le viti sulla parte superiore del motore dello scanner [B] ( x 4).
3. Riposizionare il motore dello scanner [B]. Quindi rimuovere le viti e il cavo sulla parte posteriore
( x2 x1).
83
4. Sostituzione e regolazione
Fusione
Gruppo fusore
• Prima di maneggiare il gruppo fusore, accertarsi che sia sufficientemente fredda. Il gruppo fusore
può scaldarsi notevolmente.
84
Fusione
Sensore di uscita
85
4. Sostituzione e regolazione
86
Fusione
1. Unghiette di separazione del rullo fusore e spaziatori ( P.85 "Unghiette di separazione del rullo
fusore")
2. Gruppo rullo fusore [A] ( x 2)
3. Lampada di fusione [B]
• In fase di riassemblaggio, assicurarsi che la direzione della lampada di fusione sia corretta.
87
4. Sostituzione e regolazione
• Non riciclare un termointerruttore già aperto. In tal caso, non si garantisce la sicurezza.
88
Fusione
Rullo di pressione
1. Separare il gruppo fusore in due sezioni ( P.85 "Unghiette di separazione del rullo fusore").
2. Guida di ingresso gruppo fusore [A] ( x 1)
3. 2 molle [B][C]
4. 2 bracci di pressione [D][E]
5. Boccola [F]
6. Rullo di pressione [G]
89
4. Sostituzione e regolazione
È possibile controllare la striscia di contatto, per verificare se il gruppo fusore è in buone condizioni e se
il rullo fusore e il rullo di pressione sono correttamente installati.
1. Posizionare un foglio trasparente sul vassoio bypass.
2. Attivare la modalità SP.
3. Selezionare SP1-152-001.
4. La copiatrice alimenta il foglio trasparente, e lo ferma fra il rullo fusore e il rullo di pressione per
circa 40 secondi.
5. Attendere fino a quando il foglio trasparente non viene espulso.
6. Al termine, uscire dalla modalità SP.
Si vede una striscia opaca sul foglio trasparente. Questa è la traccia della striscia di contatto. La striscia
di contatto normale è simmetrica sul foglio trasparente. Entrambi le estremità sono leggermente più
spesse rispetto al centro.
• Non esiste alcuna specifica o standard per la striscia di contatto su questa fotocopiatrice.
90
PCU e Lampada di smagnetizzazione
PCU
• Il gruppo PCU potrebbe rimanere impigliato se si tenta di estrarlo con sportello destro chiuso.
2. Aprire lo sportello anteriore.
3. Rimuovere il porta flacone di toner.
• Pulire accuratamente tutti i residui di toner attorno al flacone e nella parte interna dello
sportello anteriore
91
4. Sostituzione e regolazione
4. Estrarre il gruppo PCU [A] spingendo la parte nella direzione indicata dalla freccia rossa. ( x
1).
• Nell'installazione del gruppo PCU, assicurarsi di agganciare il cavo del connettore PCU come
illustrato sopra in modo che non si danneggi.
5. Se è stato installato un nuovo PCU, rimuovere lo Styrofoam e le etichette ( P.29 "Copiatrice" al
capitolo "Installazione").
Inizializzazione
Dopo la sostituzione, eseguire “SP2801-001” per inizializzare le impostazioni della copiatrice per
PCU.
Lampada di smagnetizzazione
92
PCU e Lampada di smagnetizzazione
93
4. Sostituzione e regolazione
Motore principale
94
Ventola di sfiato e Motore principale
• In caso di difficoltà nel fissare nuovamente due degli anelli di blocco, rimuovere il gruppo PCU
spingendo gli assi sulla parte posteriore del motore principale come illustra la figura qui di seguito.
Quindi spingere i solchi in cui sono fissati gli anelli di blocco.
95
4. Sostituzione e regolazione
Alimentazione carta
Rullo di alimentazione carta e Feltrino di frizione
1. Cassetto carta
2. Albero [A] ( x 1)
3. Rimuovere uno dei seguenti pezzi o entrambi:
• Rullo di alimentazione carta [B], indicato dalla freccia blu.
• Feltrino di frizione [C], indicato dalla freccia rossa.
96
Alimentazione carta
• Assicurarsi che l'attuatore sia in grado si spostarsi verso l'alto e verso il basso correttamente dopo
aver ricollegato il sensore di fine carta.
Sensore di registrazione
1. Cassetto carta
2. Aprire lo sportello destro.
97
4. Sostituzione e regolazione
• In caso di difficoltà nel collegamento del vano del sensore, capovolgere l'alloggiamento del rullo
di alimentazione. (Rullo di alimentazione bypass: Procedura 2)
98
Alimentazione carta
99
4. Sostituzione e regolazione
100
Alimentazione carta
1. Cassetto carta
2. Scheda di alimentazione ad alta tensione ( P.113 "Scheda di alimentazione alta tensione ")
3. Piastra di messa a terra [A] ( x 1)
4. Coperchio ingranaggio [B] ( x 1, x 7, x 2, 2 boccole)
101
4. Sostituzione e regolazione
Trasferimento immagine
Rullo di trasferimento
102
Trasferimento immagine
103
4. Sostituzione e regolazione
• Per rimuovere l'unità di trasferimento facilmente, inserire un cacciavite a lama piatta in un lato
dell'unità come indicato dalla freccia rossa, quindi sollevare per rilasciare. Quindi rilasciare l'altro
lato.
9. Sensore ID [I] ( x 1)
• In caso di difficoltà nella rimozione nel modo nr. 1 sull'immagine, rimuovere i quattro ganci sul
fondo quindi fare spazio per estrarre il sensore. Non è necessario rimuovere il coperchio del
fondo.
104
Trasferimento immagine
Piastra antistatica
105
4. Sostituzione e regolazione
BICU
Preparazione
Procedura
106
BICU e Scheda controller
• Quando si sostituisce la BICU, rimuovere la NVRAM [D] dalla scheda. Installare la NVRAM
nella nuova scheda.
5. Dopo aver sostituito la NVRAM, copiare i dati salvati in precedenza nella nuova NVRAM.
• Da una scheda SD alla NVRAM ( P.144 "Caricare/Scaricare dati NVRAM" in "Modalità
assistenza sistema" nelle appendici di questo manuale.)
Scheda controller
Preparazione:
• Prima di sostituire la scheda del controller, accertarsi di stampare l'SMC o di salvare i dati
NVRAM.
• Salvataggio dalla NVRAM del controller in una scheda SD ( P.144 "Caricare/Scaricare dati
NVRAM" in "Modalità assistenza sistema" nelle appendici di questo manuale.)
Procedura
107
4. Sostituzione e regolazione
108
BICU e Scheda controller
8. Rilasciare i ganci come indicato dalle frecce rosse, quindi tirare fuori le guide [A].
9. Rimuovere la DIMM [B] se installata.
• Lo scollegamento dei cavi dell'HDD è molto importante. Se non viene eseguito, l'HDD viene
formattato automaticamente con conseguente perdita di tutti i dati nell'HDD dovuta ai limiti di
sicurezza.
4. Rimontare la macchina.
5. Accendere la macchina.
• Se l'opzione HDD non è stata installata, la procedura d'installazione è completata.
• Se l'opzione HDD è già stata installata, procedere al passaggio successivo.
6. Spegnere l'interruttore principale della macchina e ricollegare i cavi dell'HDD.
• Stampare i rapporti SMC ("SP Mode Data" e "Logging Data") prima di sostituire la NVRAM.
109
4. Sostituzione e regolazione
• Durante la gestione dei componenti NVRAM, tenerli lontani da oggetti che possano generare
elettricità statica. Le cariche elettrostatiche possono alterare i dati contenuti nella NVRAM.
• Accertarsi di installare correttamente la NVRAM sulla scheda controller.
• Lo scollegamento dei cavi dell'HDD è molto importante. Se non viene eseguito, l'HDD viene
formattato automaticamente con conseguente perdita di tutti i dati nell'HDD dovuta ai limiti di
sicurezza.
110
BICU e Scheda controller
111
4. Sostituzione e regolazione
Altre sostituzioni
Motore fronte-retro
5. Staffa SOL ( x 4)
112
Altre sostituzioni
• Togliere la piastra isolante [C] se si deve rimuovere il solenoide di rilascio contatto ( P.115
"Solenoide di rilascio contatto") o il coperchio ingranaggio ( P.101 "Alimentazione carta e
Frizioni di registrazione").
113
4. Sostituzione e regolazione
PSU
4. PSU [B] ( x 8, x 7)
114
Altre sostituzioni
1. Porta-flacone toner
2. Sorreggere entrambi i lati della frizione di alimentazione toner [A] come illustrato dalle frecce
rosse. Quindi estrarre il proprio lato provando a rilasciare il gancio superiore come illustrato dal
quadrato rosso.
3. Rimuovere il cavo come illustra il cerchio rosso.
115
4. Sostituzione e regolazione
FCU
Batterie al litio
• Una sostituzione non corretta delle batterie al litio sul controller o sull'unità fax potrebbe causare
rischi di esplosione. Sostituire solo con batterie dello stesso tipo o di tipo equivalente consigliato
dal produttore. Smaltire le batterie usate osservando le istruzioni fornite dal produttore.
Procedura
3. FCU [A] ( x 3, x 1)
116
Altre sostituzioni
4. Quando si sostituisce la scheda FCU, rimuovere la scheda MBU dalla vecchia scheda FCU ed
installarla sulla nuova scheda FCU.
5. Impostare la data e l'ora corretta con gli Strumenti utente: Strumenti utente> Impostazioni di
sistema> Impostazione timer> Imposta Data/Ora
117
4. Sostituzione e regolazione
Gruppo laser
• Non toccare le viti sulla scheda LD sul gruppo LD. Non cercare di regolare da soli qualsiasi parte
del gruppo LD. Il gruppo LD viene regolato con precisione prima della spedizione.
• Non toccare lo specchio poligonale, il vetro di protezione, o le lenti con le mani nude.
118
Gruppo laser
Gruppo laser
• I mylar sono necessari per chiudere i fori in modo da non sporcare l'unità laser con polvere di
toner.
119
4. Sostituzione e regolazione
120
ARDF
ARDF
Gruppo ARDF
121
4. Sostituzione e regolazione
Installazione ARDF
1. Aprire l'ARDF.
2. Posizionare il coprioriginali [A] sul vetro di esposizione.
3. Allineare l’angolo posteriore sinistro del foglio coprilastra all’angolo [B] sul vetro di esposizione.
122
ARDF
4. Chiudere l'ARDF.
5. Riaprire l'ARDF.
6. Premere leggermente la superficie della lastra coprioriginali per fissarla all'ARDF.
123
4. Sostituzione e regolazione
Rullo di prelievo
Rullo di alimentazione
124
ARDF
125
4. Sostituzione e regolazione
Feltrino di frizione
126
ARDF
DFRB
127
4. Sostituzione e regolazione
128
ARDF
5. Supporto [A] ( x 1)
6. Perno [A] ( x 3)
7. Staffa [A] ( x 2)
129
4. Sostituzione e regolazione
Piastra bianca
1. Aprire l'ARDF.
130
ARDF
Sensore di registrazione
131
4. Sostituzione e regolazione
132
Regolazione area di copia dell’immagine
Stampa
Assicurarsi di aver inserito correttamente la carta in ogni cassetto prima di iniziare le regolazioni
indicate.
Per questa regolazione utilizzare il Modello area di allineamento (SP2-109-001 > 10).
1. Stampare il modello di prova con il foglio alimentato dal cassetto standard.
2. Stampare il modello di prova con il foglio alimentato dal vassoio bypass.
3. Stampare il modello di prova selezionando la stampa fronte-retro.
4. Misurare la distanza tra il bordo principale dell’area dell’immagine e il bordo principale del foglio
[A].
• La figura mostra il foglio nel vassoio di ricezione copie. Il foglio esce a faccia in giù.
SP Specifica
133
4. Sostituzione e regolazione
SP1-001-002 (Bypass) 0 ± 2 mm
SP1-001-003 (Fronte-retro) 0 ± 4 mm
SP Specifica
SP1-002-004 (Bypass) 0 ± 4 mm
SP1-002-005 (Fronte-retro) 0 ± 4 mm
Per questa regolazione utilizzare il Modello area di allineamento (SP2-109-001 > 10).
1. Stampare il modello di prova.
2. Misurare la distanza tra i 4 bordi dell’area dell’immagine e i 4 bordi del foglio [A][B][C][D].
• La figura mostra il foglio nel vassoio di ricezione copie. Il foglio esce a faccia in giù.
134
Regolazione area di copia dell’immagine
SP Specifica
• Il “Lato sinistro” e il “Lato destro” si riferiscono rispettivamente al lato sinistro e al lato destro
guardando la copia con il bordo principale rivolto verso l’alto.
4. Selezionare "Annulla" in SP2-109-001 dopo aver finito la procedura di regolazione.
Per questa regolazione utilizzare il modello a griglia (linea verticale griglia) (SP2-109-001 > 5).
SP Specifica
Scansione
Preparazione:
• Prima di regolare la scansione, regolare la stampa ( P.133 "Stampa").
• Per regolare la scansione, utilizzare un foglio di prova A4.
1. Posizionare il foglio di prova sul vetro di esposizione. Accertarsi che il foglio di prova sia allineato
con i righelli graduati posteriore e laterale del vetro di esposizione.
135
4. Sostituzione e regolazione
3. Misurare la distanza tra il bordo principale dell’area dell’immagine e il bordo principale del foglio
[A].
• La figura mostra il foglio nel vassoio di ricezione copie. Il foglio esce a faccia in giù.
4. Regolare la registrazione di scansione per il bordo principale. (SP4-010-001).
SP Specifica
5. Misurare la distanza tra il bordo laterale dell’area dell’immagine e il bordo laterale del foglio [B].
6. Regolare la registrazione da lato a lato (SP4-011-001).
SP Specifica
136
Regolazione area di copia dell’immagine
Regolazione dell’ingrandimento
1. Posizionare il foglio di prova sul vetro di esposizione. Accertarsi che il foglio di prova sia allineato
con i righelli graduati posteriore e laterale del vetro di esposizione.
2. Eseguire una copia.
3. Confrontare la copia con l’originale.
4. Regolare l'ingrandimento nella direzione di scansione principale e secondaria. L’immagine
originale [A] viene ingrandita nella direzione principale [B] o nella direzione secondaria [C] se si
specifica un valore maggiore.
• La figura mostra il foglio nel cassetto di ricezione copie. Il foglio esce a faccia in giù.
SP Specifica
137
4. Sostituzione e regolazione
Regolazione dell’immagine DF
1. Produrre un grafico di prova temporaneo come illustrato nella figura qui sopra. Utilizzare un foglio
di carta "A4/8,5 x 11".
2. Posizionare il grafico di prova temporaneo sull’ARDF.
3. Eseguire una copia.
4. Misurare la distanza fra il bordo laterale dell'area dell'immagine e il bordo laterale del foglio [A].
(La figura mostra il foglio nel vassoio di ricezione copie. Notare che il foglio esce a faccia in giù.)
5. Regolare la registrazione da lato a lato (Registrazione da lato a lato/ Facciata anteriore:
SP6-006-001, Registrazione da lato a lato/Facciata posteriore: SP6-006-002). L'area
dell'immagine si sposta verso la parte posteriore della fotocopiatrice se viene specificato un valore
maggiore.
6. Misurare la distanza tra il bordo principale dell’area dell’immagine e il bordo principale del foglio
[B].
138
Regolazione area di copia dell’immagine
139
4. Sostituzione e regolazione
140
5. Istruzioni manutenzione sistema
• Non permettere all'utente di accedere alla modalità SP o alla modalità SSP. Solo il personale di
assistenza può accedere a queste modalità. Il funzionamento della macchina NON è garantito in
caso di accesso alla modalità SP da parte di persone non appartenenti al personale di assistenza.
Tabelle SP
141
5. Istruzioni manutenzione sistema
• Se si desidera passare direttamente al programma, confermare la voce "SP Direct" [A] selezionata
e inserire il numero SP che si desidera attivare sulla tastiera. Quindi premere il tasto "#" [B].
• Quando si desidera selezionare il programma nel menu, premere i simboli [C] per scorrere le voci
del menu. Quindi premere la voce che si desidera attivare.
Inserimento di valori
1. Dopo aver localizzato un programma, premere sulla tastiera per inserire il numero come valore.
Per passare da valori positivi (più) e valori negativi (meno), premere il tasto .
2. Premere il tasto "#" [B] per confermare il valore o il tasto "C" [D] per annullare.
Mentre si sta operando in modalità SP è possibile attivare la modalità copia. Questo permette alla
fotocopiatrice di stampare immagini o modelli utilizzabili come ausilio per regolare l'impostazione SP.
1. Premere il tasto [E]. La modalità copia è attivata.
2. Specificare le impostazioni per la copia e premere il tasto [E].
3. Per tornare in modalità SP, premere la voce "A SP" visualizzata nell'angolo superiore sinistro sul
pannello.
Premere la voce "Esci" visualizzata nell'angolo superiore destro sul pannello per uscire dal programma
o terminare la modalità SP.
• Asterisco (*): Le impostazioni vengono memorizzate nella NVRAM. La maggior parte di tali
impostazioni ritornano ai valori predefiniti quando si esegue il programma SP5-801-002. CTL
indica che i dati sono salvati nella NVRAM sulla scheda del controller.
142
Programma di assistenza tecnica
143
5. Istruzioni manutenzione sistema
Seguire questa procedura per caricare le impostazioni del codice SP dalla NVRAM ad una scheda SD.
• Questo dato andrebbe sempre caricato su una scheda SD prima che la NVRAM venga sostituita.
1. Prima di spegnere la macchina, eseguire l'SP 5990-1 (Stampa SMC). Se il caricamento non
riesce, è necessario un record delle impostazioni NVRAM.
2. Spegnere la fotocopiatrice.
3. Rimuovere il coperchio interfaccia ( x 1).
4. Inserire la scheda SD nello slot 2 riservato all'assistenza, quindi accendere la macchina.
5. Eseguire SP 5824-1 (Caricamento dati NVRAM) quindi premere il tasto "Esegui".
• Una volta terminato il download, un file viene copiato ad una cartella NVRAM sulla scheda
SD. Il file viene salvato con il percorso e il nome del file:
NVRAM\<numero di serie>.NV
Ecco un esempio con numero di serie "B0700017":
NVRAM\B0700017.NV
6. Per evitare errori durante il download, accertarsi di contrassegnare la scheda SD contenente i dati
caricati (salvati) con il numero della macchina dalla quale i dati erano stati caricati (salvati).
• I dati NVRAM provenienti da più di una macchina possono essere caricati (salvati) sulla
stessa scheda SD.
7. Spegnere la fotocopiatrice, quindi rimuovere la scheda SD dallo slot 2.
8. Rimontare la macchina.
Per trasferire i dati NVRAM da una scheda SD alla NVRAM installata nella macchina, eseguire la
procedura qui indicata.
• Il download dei dati NVRAM da una scheda SD può non essere eseguito correttamente in caso di
scheda SD difettosa o di problemi di collegamento tra controller e scheda BICU.
• Se il download fallisce, ripetere l'operazione.
144
Uso della modalità SP
• Se fallisce anche il secondo tentativo, inserire i dati della NVRAM manualmente usando la stampa
SMC creata in precedenza prima di caricare i dati NVRAM. ( la procedura qui sopra)
1. Spegnere la fotocopiatrice.
2. Rimuovere il coperchio dell'interfaccia 2 ( x 1).
3. Inserire la scheda SD contenente i dati NVRAM nello slot 2 riservato all'assistenza.
4. Accendere la fotocopiatrice.
5. Eseguire SP 5825-1 (Download dati NVRAM) e premere il tasto "Esegui".
6. Spegnere la fotocopiatrice, quindi rimuovere la scheda SD dallo slot 2.
7. Rimontare la macchina.
• Perché i dati della NVRAM si scarichino correttamente, il numero di serie del file sulla scheda
SD deve corrispondere al numero di serie della macchina. Se i numeri di serie non
corrispondono, il download non riuscirà.
Questa procedura scarica (salva) i seguenti dati sulla NVRAM:
• Contatore totale
• Conteggio C/O, P/O
Prima di iniziare…
Una scheda SD è un dispositivo di precisione, per cui è necessario adottare le seguenti precauzioni nel
maneggiarla:
• Spegnere sempre la macchina prima di inserire una scheda SD. Non inserire mai la scheda SD
nello slot mentre la macchina è accesa.
• Se la macchina è accesa, non rimuovere mai la scheda SD dallo slot riservato all'assistenza.
• Non spegnere mai la macchina durante il download del firmware dalla scheda SD.
• Riporre le schede SD in un luogo sicuro dove non siano esposte a temperatura ed umidità elevate,
o alla luce diretta del sole.
• Maneggiare sempre le schede SD con la massima cura per evitare di piegarle o graffiarle. Non
fare mai cadere una scheda SD o esporla ad altri colpi o vibrazioni.
145
5. Istruzioni manutenzione sistema
Tenere a mente i punti seguenti durante l’uso del software di aggiornamento firmware:
• “Caricare” significa trasferire i dati dalla macchina alla scheda SD, mentre “Scaricare” significa
trasferire i dati dalla scheda SD alla macchina.
• Per selezionare un elemento sullo schermo LCD, premere il pulsante appropriato sul pannello di
cotnrollo, oppure premere il tasto numerico appropriato sulla tastiera a 10 cifre del pannello di
controllo.
• Prima di iniziare la procedura di aggiornamento del firmware, accertarsi che la macchina sia
scollegata dalla rete in modo da evitare che arrivi un lavoro di stampa mentre si sta eseguendo
l’aggiornamento.
• Prima di iniziare la seguente operazione, verificare quali versioni del firmware siano attualmente
installate sulla macchina con l'SP7-801-255.
-Preparazione della Scheda SD-
1. Formattare una scheda SD utilizzando, per esempio, SD Formatter versione 1.1.
2. Creare una cartella "romdata" sulla scheda SD.
3. Creare le seguenti cartelle all'interno della cartella "romdata": B121, B620, B622, B658, B681,
B685
4. Scaricare il firmware dal server e memorizzare i file nella cartella con il codice modello
corrispondente sulla scheda SD.
Esempio:
Il file B1215540B andrebbe salvato nella cartella “B121”, mentre i file B6585902B,
B6585903B e B6585905B andrebbero salvati nella cartella “B658”.
-Aggiornamento firmware-
• Non inserire più di un programma firmware macchina sulla stessa scheda SD. Copiare solo il
fimware del modello desiderato.
1. Spegnere la macchina utilizzando l’interruttore principale.
2. Se la macchina è collegata ad una rete, scollegare il cavo di rete dalla fotocopiatrice.
3. Rimuovere il coperchio interfaccia ( x 1)
4. Con l'etichetta sulla scheda SD rivolta verso il lato posteriore della macchina, inserire la scheda SD
nello slot 2 sulla scatola del controller. Premere delicatamente la scheda SD nello slot fino a
bloccarla.
5. Accertarsi che la scheda SD sia inserita e bloccata in posizione.
146
Uso della modalità SP
(Per rimuovere una scheda SD, premerla per sbloccare la molla che la blocca e quindi rilasciarla
facendola uscire dallo slot.)
6. Accendere l'interruttore principale. Trascorsi 45 secondi circa viene visualizzata sullo schermo LCD
la schermata iniziale di aggiornamento della versione, in inglese.
7. Premere sullo schermo o sul pannello di controllo il pulsante o il tasto corrispondenti alla voce di
menu da aggiornare.
ROM/NEW Significato
Indica il numero del modulo e il nome della versione presenti sulla scheda
NEW: SD. La prima riga corrisponde al numero del modulo, la seconda al nome
della versione.
• I moduli firmware del controller, della macchina base e del pannello di controllo non possono
essere aggiornati contemporaneamente. Si raccomanda di aggiornarli uno alla volta.
8. Sfiorare "UpDate (#)" (o ) per avviare l'aggiornamento.
• La barra di avanzamento non mostra il firmware del pannello operativo dopo avere toccato
"OpPanel". Il tasto di accensione si accende e si spegne ad intervalli di 0,5 secondi durante
l'aggiornamento del firmware. Il tasto di accensione si accende e si spegne ad intervalli di 3
secondi una volta completato l'aggiornamento.
9. Alla fine dell'aggiornamento sul pannello di comando appare il messaggio "Update is Done"
(Aggiornamento completato). Il messaggio visualizzato dipende dal firmware che è stato
aggiornato.
10. Quando viene visualizzato il messaggio "Update is Done" (Aggiornamento completato) spegnere
la macchina tramite l'interruttore principale, oppure seguire le istruzioni visualizzate sul pannello di
comando.
11. Premere la scheda SD verso il basso per sbloccarla. Quindi toglierla dallo slot.
12. Accendere la copiatrice normalmente.
Messaggi di errore
Se si verifica un errore durante il download viene visualizzato un messaggio di errore nella prima riga.
Il codice di errore è composto dalla lettera "E" e da un numero. Nell'esempio raffigurato è visualizzato il
codice d'errore "E24". Per i dettagli, fare riferimento alla tabella dei messaggi di errore (vedere
"Gestione errori di aggiornamento firmware").
147
5. Istruzioni manutenzione sistema
Se l'aggiornamento della ROM viene interrotto a seguito di mancanza accidentale di corrente, non è
possibile garantire il regolare funzionamento della macchina al riavvio. Se l'aggiornamento della ROM
non è andato a buon fine per qualsiasi ragione, per poter garantire il regolare funzionamento della
macchina viene visualizzato l'errore di aggiornamento ROM fino a quando l'aggiornamento non è
andato a buon fine.
A tal fine reinserire la scheda ed accendere la macchina per continuare automaticamente il download
del firmware dalla scheda senza la visualizzazione dei menu.
148
Uso della modalità SP
Se si verifica un errore durante il download, verrà visualizzato un messaggio di errore nella prima linea.
Il codice di errore è composto dalla lettera "E" e da un numero (ad esempio E20).
Errore nell’accesso alla scheda Accertarsi che la scheda SD sia inserita correttamente o
24
SD utilizzare un’altra scheda SD.
149
5. Istruzioni manutenzione sistema
33 Versione di scheda SD errata Dati ROM non corretti sulla scheda SD o dati corrotti.
Errore del modulo – il modulo L'aggiornamento dati della scheda SD non è corretto. I
35 sulla scheda SD non è di questa dati sulla scheda SD appartengono ad un'altra
macchina macchina. Acquisire i dati corretti e reinstallare.
Download del modulo engine Sostituire i dati di aggiornamento del modulo sulla
40
fallito scheda SD e riprovare o sostituire la scheda BICU.
Download del modulo del Sostituire i dati di aggiornamento del modulo sulla
42
pannello di controllo fallito scheda SD e riprovare o sostituire l’LCDC.
Download modulo dati timbro Sostituire i dati di aggiornamento del modulo sulla
43
fallito scheda SD e riprovare o sostituire l’hard disk.
1. Fare clic sull'elemento che si desidera attivare, quindi apparirà "OK" sul pannello.
150
Uso della modalità SP
Modelli di prova
Nr. Modello
0 Nessuno
15 Pied-de-poule
16 Pied-de-poule
151
5. Istruzioni manutenzione sistema
Cancella memoria
La macchina memorizza i dati del motore nella NVRAM sulla BICU, e memorizza gli altri dati nella
NVRAM sul controller opzionale. Per distinguere fra i dati del motore e gli altri dati, vedere
l'SP5-801-003 fino a 015. Questo programma di assistenza (SP5-801) gestisce i dati del controller. I
dati nella NVRAM della BICU (dati motore) vengono cancellati mediante SP5-801-002 mentre i dati
nella NVRAM del controller (dati del controller) vengono cancellati mediante altri programmi in
SP5-801 (per le eccezioni, vedere al capitolo "Eccezioni" come descritto di seguito).
Eccezioni
SP5-801-002 azzera la maggior parte delle impostazioni e dei contatori memorizzati nella NVRAM
presente sulla scheda BICU (vengono ripristinati i valori di default). Tuttavia, le seguenti impostazioni
non vengono cancellate:
• SP5-811-003 (Nr.seriale della macchina [Visualizza codice ID2])
• SP5-812-001 (Impostazioni nr.tel assistenza [Servizio])
• SP5-812-002 (Impostazione nr.tel. assistenza [Fax])
• SP5-907 (Nome modello/Dispositivo Plug & Play)
• SP7 (Registro dati)
152
Uso della modalità SP
1. Stampare tutti gli elenchi dei dati SMC ( P.153 "Stampa SMC (SP5-990)").
2. Eseguire SP5-801-002.
3. Premere il tasto OK.
4. Selezionare “Esegui.” Viene visualizzato il messaggio "Esegui?" seguito da "Annulla" e "Esegui".
5. Selezionare “Esegui.”
6. Se il programma termina in modo normale, viene visualizzato il messaggio "Completato". Se il
programma termina in modo anomalo, viene visualizzato un messaggio di errore.
7. Spegnere e riaccendere la macchina.
8. Regolare la registrazione e l'ingrandimento della stampante e dello scanner (* "Regolazione
copia" nel capitolo "Sostituzione e Regolazione").
9. Fare riferimento alle liste SMC, ed inserire i valori che differiscono dalle impostazioni di fabbrica.
10. Inizializzare il developer (SP 2-801-001).
11. Controllare la qualità della copia e il percorso della carta.
SP5-990 permette di effettuare la stampa degli elenchi dei messaggi di manutenzione e macchina.
1. Selezionare SP5-990.
2. Selezionare un menu:
• -001 Tutto (Elenco dati), -002 SP (Elenco dati modalità), -003 Programma utente, -004 Dati
registrazione, -005 Rapporto diagnostico, -006 Non-predefinito, -007 Riepilogo NIB, -008
Registro di acquisizione, -021 Programma utente copiatrice, -022 SP scanner, -023
Programma utente scanner
• La stampa effettuata mediante il menu "Font grandi (Big Font)" è adatta per la trasmissione via
fax.
3. Premere il tasto "Esegui".
• Vengono stampati gli elenchi dello stato della macchina.
153
5. Istruzioni manutenzione sistema
4. Per tornare in modalità SP, fare clic sulla voce "A SP" visualizzata nell'angolo sinistro superiore sul
pannello.
• Sensore ID difettoso
SP2-220-2 Vsg Vsp > 2,5V o
• Sensore ID sporco -
(VG sul display) (Vsg – Vsg) < 1,00V
• Tamburo non caricato
Nessuna condizione di
SP2-220-3 Vsdp -
errore
Vt > 4,5 V o
SP2-220-4 Vt • Sensore TD difettoso -
Vt < 0,2 V
SP2-220-5 Vtref - - -
154
Tabelle Assistenza Fax
155
5. Istruzioni manutenzione sistema
156
6. Risoluzione dei problemi
Tabelle SC
Riepilogo
Per prevenire eventuali danni, la macchina non Attivare la modalità SP, quindi
A funziona fino a quando il tecnico addetto spegnere e riaccendere la
all'assistenza non azzera il codice SC. macchina.
Spegnere e riaccendere la
La macchina funziona normalmente ad eccezione
C macchina dall’interruttore
dell'unità oggetto della chiamata di assistenza.
generale.
157
6. Risoluzione dei problemi
Nr.
Sintomo Possibile causa
Definizione
158
Tabelle SC
Nr.
Sintomo Possibile causa
Definizione
Errore LSYNC
Errore risposta RI
-002 B • IPU (BICU, ICTL) difettoso o
Rilevamento di un errore all'acceso a RI.
prestazioni RI anormali, ecc
159
6. Risoluzione dei problemi
Nr.
Sintomo Possibile causa
Definizione
160
Tabelle SC
Nr.
Sintomo Possibile causa
Definizione
• Collegamento o scollegamento
difettoso tra cavo I/F e gruppo
rilevamento sincronizzazione.
220 B Segnale rilevamento sincronizzazione • Rilevamento sincronizzazione
output non entro 200ms dopo difettoso
l'illuminazione LD a rotazione costante.
• Il fascio non arriva al fotorilevatore
• Parti collegate a GAVD, driver LD,
LDB e BICU difettose
161
6. Risoluzione dei problemi
Nr.
Sintomo Possibile causa
Definizione
Errore sensore P
162
Tabelle SC
Nr.
Sintomo Possibile causa
Definizione
Errore sensore T
• Sensore P difettoso
Il sensore P non rileva un modello
corretto durante l'inizializzazione del • Sensore T difettoso
392 B developer (SP2-801-001). • Non rimuovere il sigillo termico
Quando l'output di Vsp è superiore a • Funzionamento del tamburo
2,5V, un SC appare in caso di mancata difettoso
rimozione del sigillo termico o di
• Funzionamento del rullo di sviluppo
assenza del developer.
difettoso
163
6. Risoluzione dei problemi
Nr.
Sintomo Possibile causa
Definizione
164
Tabelle SC
Nr.
Sintomo Possibile causa
Definizione
165
6. Risoluzione dei problemi
Nr.
Sintomo Possibile causa
Definizione
Errore timeout
• Termistore difettoso
545 A La lampada di fusione rimane attiva per
• Scollegamento del riscaldatore
12 secondi dopo l'avviamento della
modalità di attesa. • Dopo l'attivazione di dispositivo
anti-surriscaldamento
166
Tabelle SC
Nr.
Sintomo Possibile causa
Definizione
• ADF difettoso
620 B Scollegamento dopo collegamento
• Scheda IPU difettosa
normale.
• Collegamento ADF difettoso
167
6. Risoluzione dei problemi
Nr.
Sintomo Possibile causa
Definizione
168
Tabelle SC
Nr.
Sintomo Possibile causa
Definizione
SC6xx
Nr.
Sintomo Possibile causa/Contromisura
Definizione
169
6. Risoluzione dei problemi
Nr.
Sintomo Possibile causa/Contromisura
Definizione
Errore versione
-002 B La versione del modulo di 1. Installare il file corretto del modulo di
autenticazione esteso non è corretta. autenticazione esteso.
170
Tabelle SC
Nr.
Sintomo Possibile causa/Contromisura
Definizione
Errore di autenticazione
171
6. Risoluzione dei problemi
Nr.
Sintomo Possibile causa/Contromisura
Definizione
SC8xx
Nr.
Sintomo Possibile causa/Contromisura
Definizione
172
Tabelle SC
Errore monitor
819 In seguito ad un errore del controllo, si è verificata una saturazione della RAM durante
l'esecuzione del programma di sistema. Sul pannello operatore è stato visualizzato uno
dei seguenti messaggi.
[----] B Altri
173
6. Risoluzione dei problemi
• CPU difettosa
• Bus locale difettoso
B Errore di accesso alla cache nella 1. Spegnere e riaccendere la macchina
CPU dall’interruttore generale.
2. Reinstallare il programma di sistema.
3. Sostituire la scheda controller.
174
Tabelle SC
Errore ASIC
175
6. Risoluzione dei problemi
176
Tabelle SC
Errore PHY IC
• Collegamento difettoso
• NVRAM standard difettosa
824 • Controller difettoso
B Il controller non riconosce la
[1401] NVRAM standard installata o rileva 1. Controllare che la NVRAM standard
una condizione di NVRAM difettosa. sia correttamente inserita nello
zoccolo.
2. Sostituire la NVRAM.
3. Sostituire il controller.
177
6. Risoluzione dei problemi
Errore di verifica
• Collegamento difettoso
[0301]
829 B • Accertarsi che la RAM residente sia
Errore di verifica (slot 1) installata nello slot corretto.
178
Tabelle SC
179
6. Risoluzione dei problemi
180
Tabelle SC
• Controller difettoso
857 C E' stato rilevato un errore 1. Controllare le connessioni USB, ed
nell'interfaccia USB. accertarsi che siano connesse bene.
2. Sostituire la scheda controller.
Altro errore:
[31] Si è verificato un grave errore • Come per SC991
durante la crittografia dei dati.
181
6. Risoluzione dei problemi
182
Tabelle SC
Errore scheda SD
183
6. Risoluzione dei problemi
• Dati corrotti
• Disco fisso difettoso
E' stato eseguito l'accesso alla
rubrica nel disco fisso. E' stato • Software del controller difettoso
870 C rilevato un errore nei dati della 1. Sostituire il disco fisso (i codici utente
rubrica; i dati della rubrica non sono e i contatori vengono recuperati
stati letti; oppure i dati non sono stati quando l'interruttore generale viene
scritti nella rubrica. acceso se quei dati sono memorizzati
nello Smart Device Monitor for
Admin).
184
Tabelle SC
876 È stato rilevato un errore nella gestione dei dati di registro all'accensione o durante il
funzionamento della macchina. Questo può essere causato dallo spegnimento della
macchina mentre era in corso un'operazione.
185
6. Risoluzione dei problemi
186
Tabelle SC
Errore TPM
Errore TCSD
187
6. Risoluzione dei problemi
Software difettoso.
Questo errore si verifica nei seguenti • Causato da informazioni senza
881 B casi: autenticazione memorizzate nel
software (NON causato da
1. Inviando un lavoro alla stampante operazioni dell'utente)
2. Accendendo dal pannello 1. Riavviare la macchina
3. Accedendo dal browser web
1. Riavviare la macchina
899 B Si è verificata un'operazione 2. Aggiornare il firmware.
anomala nel programma del 3. Se questo SC non si cancella con i
controller (Hardware o software) processi Nr.1, 2, sostituire la scheda
controller.
SC9xx
Errore stampante
188
Tabelle SC
189
6. Risoluzione dei problemi
190
Anomalie dei componenti elettrici
CN127
Sensore di SN (PFU1: Inceppamento carta -
registrazione Sensore fine
carta)
CN129
CN130
Sensore di fine carta SN (PFU1: La macchina non riesce a rilevare la
(Nessuno)
bypass Sensore fine carta sul vassoio bypass.
carta)
CN128
Sensore percorso SN (PFU1: Inceppamento carta -
carta Sensore fine
carta)
CN128
CN132
Sensore densità SN (PFU1: La qualità di stampa potrebbe
(Nessuno)
immagine (ID) Sensore fine peggiorare.
carta)
191
6. Risoluzione dei problemi
CN404 SC120 -
Sensore posizione di SN (PFU1:
partenza scanner Sensore fine SC120 -
carta)
CN404 SC120 -
Sensore SN (PFU1:
coprioriginali La copiatrice non si riscalda quando
Sensore fine (Nessuno)
si apre il coprioriginali.
carta)
DF CN03 -
Sensore di SN (PFU1: Inceppamento carta Gli originali vengono trasportati
registrazione DF Sensore fine
correttamente.
carta)
DF CN04 -
192
Anomalie dei componenti elettrici
Sportello anteriore
CN114 -
Interruttore sportello aperto
anteriore Sportello anteriore
SW
aperto
Fusibili bruciati
Valore nominale
Fusibile Con interruttore generale acceso
100 – 127 V 250 V
193
6. Risoluzione dei problemi
Salvataggio su scheda:
• La funzione salvataggio su scheda viene usata per salvare lavori di stampa ricevuti dalla
stampante su una scheda SD priva di funzionalità di stampa. La modalità salvataggio su scheda
viene attivata usando il bit switch della stampante #1 numero 4. La funzione salvataggio su scheda
rimarrà attivata finché la scheda SD non si riempirà completamente oppure finché non saranno
stati usati tutti i nomi dei file.
• I file sono archiviati sulla scheda SD nella cartella /prt/cardsave. I nomi dei file vengono
assegnati in modo sequenziali da PRT0000.prn a PRT9999.prn. Verrà creato un file PRT.CTL
aggiuntivo. Il file contiene un elenco di tutti i file creati sulla scheda attraverso la funzione
salvataggio su scheda.
• I file archiviati precedentemente sulla scheda SD possono essere sovrascritti o lasciati intatti. La
scheda SD per il salvataggio dispone delle voci di menu "Add" (Aggiungi) e "New" (Nuovo).
• Card Save (Add): (Salvataggio su scheda: aggiungi) Aggiunge dei file alla scheda SD. Non
sovrascrive i file esistenti. Se la scheda diventa piena o se sono stati utilizzati tutti i nomi di file,
verrà visualizzato un errore sul pannello di comando. I lavori successivi non verranno
memorizzati.
• Card Save (New): (Salvataggio su scheda: nuovo) Sovrascrive i file nella directory /prt/
cardsave della scheda.
Limitazione:
• La funzione di salvataggio su scheda non può essere usata con i comandi PJL Status Readback. I
comandi PJL Status Readbacks non funzioneranno. Inoltre causeranno la mancata esecuzione
della funzione Salvataggio su scheda.
Procedura
194
Funzione salvataggio su scheda
5. Selezionare "SP1-001-001".
1. Utilizzare il tasto numerico "4" per attivare il bit 4 e assicurarsi di premere il pulsante "#" per
confermare. Il risultato dovrebbe essere: 00010000 come illustrato. Eseguendo tale procedura,
nel menu "List/Test Print" (Stampa lista/prova) appare l'opzione "Card Save" (Salvataggio su
scheda).
2. Uscire dalla modalità SP.
3. Premere il tasto " ".
4. Selezionare "Printer Features" (Impostazioni Stampante).
5. Selezionare "Stampa lista/prova".
195
6. Risoluzione dei problemi
Messaggi di errore
196
Guida alla Risoluzione dei problemi per il Fax
197
6. Risoluzione dei problemi
198
7. Risparmio energetico
Risparmio energetico
Modalità risparmio energetico
L'utente deve utilizzare le modalità di risparmio energia in modo corretto per risparmiare energia e
proteggere l'ambiente.
La zona ombreggiata del diagramma indica il quantitativo di energia che si risparmia con i timer
impostati sui valori di default. Se le impostazioni dei timer vengono modificate, il risparmio energetico
varia. Ad esempio, se il timer viene impostato su 240 minuti la zona ombreggiata scompare e non si ha
alcun risparmio energetico prima che siano trascorsi 240 minuti.
Impostazioni timer
199
7. Risparmio energetico
Predefinito: [1 minuto]
Il tempo può essere impostato da 10 secondi a 240 minuti, utilizzando i tasti numerici.
Il timer modalità sospensione può non funzionare quando appare un messaggio di errore.
A seconda dell'architettura software integrata installata, la macchina può impiegare più tempo di quello
indicato per entrare in modalità sospensione.
Raccomandazione
SP 8941 (Stato macchina) registra il tempo che la macchina ha trascorso in ciascuna modalità.
• 8941-001: modalità di funzionamento
• 8941-002: modalità pronto
• 8941-005: modalità sospensione
Sulla base di questi di dati e dei valori dei consumi riportati nelle specifiche tecniche è possibile stimare
l'energia consumata dalla macchina.
Si tratta di un valore di riferimento, perché i consumi riportati nelle specifiche tecniche sono stati misurati
in ambiente controllato con alimentazione elettrica costante.
Per avere una misura esatta del consumo effettivo, utilizzare un wattmetro.
Utilizzare SP8941 per calcolare il consumo energetico:
• All'inizio del periodo di misurazione, leggere i valori di SP8941 001 002 005.
• Al termine del periodo di misurazione, leggere nuovamente i valori di SP8941 001 002 005.
• Individuare quanto tempo è trascorso nelle singole modalità (sottraendo la prima misura
dall'ultima).
• Moltiplicare il valore trovato per il consumo specificato per le singole modalità.
200
Risparmio energetico
Differenza di
Consumo
Ora Ora di tempo
Consumo SP8941: d'inizio: fine: (Dati:a x
Macchina (Dati: b -
energia (W): Stato Dati:d)
Data (min.) (min.) Dati: c)
Dati: a macchina (Wmin.)
Dati: b Dati: c (min.)
Dati: e
Dati: d
Modalità 001:
di Tempo di
funzionam funzionam
ento 1081.8 ento 21089.0 21386.0 297.0 321294.6
Modalità 002:
Pronto Tempo in
(standby) 214.0 standby 306163.0 308046.0 1883.0 402962.0
005:
Tempo in
Modalità
modalità
sospension
spegnimen
e
7.0 to 508776.0 520377.0 11601.0 81207.0
201
7. Risparmio energetico
Risparmio carta
Efficacia della funzione Fronte-retro/Combina
La copiatura Fronte-retro abbinata alla modalità Combina riduce il quantitativo di carta utilizzato. In
questo modo si risparmia energia sulla produzione della carta, con conseguente riduzione
dell’inquinamento ambientale.
1. Fronte-retro:
2. Combina:
3. Fronte-retro + Combina:
202
Risparmio carta
Per tenere sotto controllo il consumo di carta, leggere il contatore copie totali e quello delle copie
fronte-retro.
Il contatore copie totali conta tutte le pagine stampate.
• Quando si fa una copia fronte-retro il contatore copie totali aumenta di 2.
• Per una copiatura fronte-retro di un documento originale di 3 pagine il contatore copie totali
aumenta di 3.
Il contatore delle copie fronte-retro conta le pagine stampate su entrambi i lati.
• Quando si fa una copia fronte-retro, il contatore delle copie fronte-retro aumenta di 1.
• Per un lavoro di copiatura di un originale di 3 pagine, il contatore delle copie fronte-retro aumenta
solo di 1, anche se vengono utilizzati due fogli.
Raccomandazione
Spiegare ai clienti le caratteristiche sopraindicate, affinché sappiano come ridurre l'uso di carta.
Modello S-C5
203
7. Risparmio energetico
Fronte-retro:
Total counter
Foglio Carta Contatore fronte-
Foglio utilizzato (Contatore
Originali: utilizzato su risparmiat retro
su un solo lato copie totali)
due lati a SP8411-001
SP8501-001
1 1 1 0 1 0
2 2 1 1 2 1
3 3 2 1 3 1
4 4 2 2 4 2
5 5 3 2 5 2
10 10 5 5 10 5
20 20 10 10 20 10
Se si utilizza la modalità combinata il contatore totale e il contatore fronte-retro funzionano come già
spiegato. Nella tabella seguente sono riportati i risparmi di carta e le modalità di incremento dei
contatori per alcuni esempi semplici di copiatura fronte-retro + modalità combinata.
Modalità 2 in 1:
Total counter
Foglio Carta Contatore fronte-
Foglio utilizzato (Contatore copie
Originali: utilizzato su risparmiat retro
su un solo lato totali)
due lati a SP8421-004
SP8501-001
1 1 1 0 1 1
2 2 1 1 1 1
3 3 2 1 2 2
4 4 2 2 2 2
5 5 3 2 3 2
10 10 5 5 5 5
20 20 10 10 10 10
204
Risparmio carta
Modalità fronte-retro + 2 in 1:
Total counter
Foglio Carta Contatore fronte-
Foglio utilizzato (Contatore copie
Originali: utilizzato su risparmiat retro
su un solo lato totali)
due lati a SP8421-005
SP8501-001
1 1 1 0 1 1
2 2 1 1 1 1
3 3 1 2 2 2
4 4 1 3 2 2
5 5 2 3 3 3
6 6 2 4 3 3
7 7 2 5 4 4
8 8 2 6 4 4
9 9 3 6 5 5
10 10 3 7 5 5
11 11 3 8 6 6
12 12 3 9 6 6
205
MEMO
206
MEMO
207
MEMO
208 IT
Model S-C5
Machine Code: D127/D128
Appendices
26 November, 2011
TABLE OF CONTENTS
1. Appendix: Specifications
Specifications......................................................................................................................................................3
Copier.............................................................................................................................................................3
Printer...............................................................................................................................................................5
Scanner...........................................................................................................................................................6
FAX..................................................................................................................................................................7
ARDF.............................................................................................................................................................11
Paper Tray Unit............................................................................................................................................11
Supported Paper Sizes....................................................................................................................................13
Original Paper Sizes....................................................................................................................................13
Paper Feed...................................................................................................................................................14
2. Appendix: Preventive Maintenance Tables
Maintenance Tables........................................................................................................................................17
3. Appendix: SP Mode Tables
System Service Mode......................................................................................................................................19
Service Mode Tables (System SP Tables)..................................................................................................19
Input Check (SP5-803).............................................................................................................................143
Output Check (SP5-804)..........................................................................................................................145
Printer Service Mode (Print SP Tables)....................................................................................................147
Scanner Program Mode Table (Scanner SP Tables)..............................................................................152
4. Appendix: Fax Troubleshooting Guide
Fax Error Codes.............................................................................................................................................157
IFAX Troubleshooting....................................................................................................................................176
IP-Fax Troubleshooting..................................................................................................................................179
IP-Fax Transmission...................................................................................................................................179
IP-Fax Reception........................................................................................................................................182
5. Appendix: Fax Service Program
System Service Mode....................................................................................................................................185
SP1-XXX (Bit Switches)..............................................................................................................................185
SP2-XXX (RAM).........................................................................................................................................186
SP3-XXX (Machine Set)............................................................................................................................186
SP4-XXX (ROM Version)...........................................................................................................................187
SP5-XXX (RAM Clear)...............................................................................................................................187
1
SP6-XXX (Report).......................................................................................................................................188
SP7-XXX (Tests)..........................................................................................................................................190
Bit Switches.....................................................................................................................................................191
System Switches.........................................................................................................................................191
I-Fax Switches ...........................................................................................................................................202
Printer Switches..........................................................................................................................................210
Communication Switches..........................................................................................................................215
G3-1 Switches...........................................................................................................................................223
IP Fax Switches..........................................................................................................................................234
NCU Parameters............................................................................................................................................243
Dedicated Transmission Parameters.............................................................................................................257
Programming Procedure...........................................................................................................................257
Parameters.................................................................................................................................................257
2
1. Appendix: Specifications
Specifications 1
Copier
Configuration: Desktop
Originals: Sheet/Book/Object
Maximum
Original Size: A4 / 81/2" x 14"
A4 / 81/2" x 14" (ARDF)
Maximum
A4 SEF / 81/2" x 11" SEF (Copier's paper tray)
A4 SEF / 81/2" x 14" SEF (Bypass)
A4 SEF / 81/2" x 14" SEF (Optional paper tray)
A4 SEF / 81/2" x 14" SEF (Duplex)
Minimum
Copy Paper Size: A5 LEF / 81/2" x 51/2" LEF (Copier's paper tray)
A6 SEF/ 81/2" x 51/2" (Bypass)
A4 SEF / 81/2" x 11” SEF (Optional paper tray unit)
A4 SEF / 81/2" x 11” SEF (Duplex)
Custom sizes in the bypass tray:
Width: 90 – 216 mm (3.5" – 8.5")
Length: 139 – 600mm (5.48" – 23.62")
3
1. Appendix: Specifications
A4 Version LT Version
200% 155%
Enlargement
1 141% 129%
93% 93%
Reduction 71% 78%
50% 65%
Standby 40 dB
Noise Emission:
Operating (copier only) 66.5 dB
4
Specifications
6 seconds or less
Note: Measurement conditions
• From the ready state, with the polygonal mirror motor spinning.
First Copy Time:
• A4/LT SEF copying
1
• From copier's paper tray
• The time from pushing copy start button
Default: 1 minute
Auto Off Timer
Range: 1 to 240 minutes
Default: 1 minute
Energy Saver Timer:
Rage: 1 to 240 minutes
Printer
5
1. Appendix: Specifications
RPCS
PCL5e / 6 (XL)
Printer language: PostScript3
Adobe PS3/PDF
Media Print: JPEG / TIFF
PCL:
45 fonts
13 International fonts
Resident Fonts:
PS:
136 fonts
Euro Currency supported.
Memory: 1GB
Scanner
6
Specifications
Maximum power
Less than 900 W
consumption
10/100BASE-TX(TCP/TP)
Interface Ethernet interface (10BASE-T or 100BASE-TX)
IEEE 802.11a/b/g (Wireless LAN),
*1 Scanning speeds vary according to machine operating conditions, computer (specifications, network
traffic, software, etc.), and original types.
FAX
General
PSTN
Circuit:
PBX
7
1. Appendix: Specifications
G3
G3: 33600/31200/28800/26400/24000/21600/
Data Rate: 19200/16800/14400/12000/9600/7200/4800/2400 bps
Automatic fallback
ECM: 128 KB
SAF
Memory Capacity: Standard: 4 MB
Page Memory:
Standard: 4 MB (Print: 2 MB + Scanner: 2 MB)
IFAX Specifications
8
Specifications
Document Size:
• To use B4 and A3 width, IFAX SW00 Bit 1 (B4) and/or Bit 2 (A3) must
be set to “1”.
Single/multi-part
E-mail File Format: MIME conversion
Image: TIFF-F (MH, MR, MMR), JBIG
Transmission:
SMTP, TCP/IP
Protocol:
Reception:
POP3, SMTP, IMAP4, TCP/IP
100 Mbps(100base-Tx)
Data Rate:
10 Mbps (10base-T)
SMTP-AUTH
Authentication
POP before SMTP
Method:
A-POP
Remark: The machine must be set up as an e-mail client before installation. Any client
PCs connected to the machine through a LAN must also be e-mail clients, or
some features will not work (e.g. Autorouting).
9
1. Appendix: Specifications
IP-FAX Specifications
1 Network:
Ethernet/10base-T, 100base-TX
IEEE1394 (IP over 1394)
IEEE802.11b (wireless LAN)
FCU -
Option for D127
MBU - -
Standard for D128
Speaker -
10
Specifications
ARDF
11
1. Appendix: Specifications
• 2 units can be installed at maximum. When more than 3 units are installed, SC occurs and the
operation doesn’t work.
12
Supported Paper Sizes
ARDF
Paper Size (W x L) Book
Simpl. Dupl.
13
1. Appendix: Specifications
ARDF
Paper Size (W x L) Book
Simpl. Dupl.
Width 139-216 mm
Custom: – X*3 X*2, 4
Length 139-356 mm
Symbol meanings:
X: Can use
–: Cannot use
*1: Can be used when the ARDF is installed
*2: 55k (17 lb./ 64 g/m2) or less original cannot be used.
*3: Width: 139-216 mm, Length: 139-1260 mm
*4: Width 139-216 mm, Length: 160-356 mm
Paper Feed
The copier and optional paper feed unit do not detect paper sizes. The following table lists the paper
sizes that the copier and optional paper feed unit can transport.
14
Supported Paper Sizes
15
1. Appendix: Specifications
C5 162 x 229 mm – X – –
1 C6 114 x 162 mm – X – –
Symbol meanings:
X: Can transport
–: Cannot transport
16
2. Appendix: Preventive Maintenance
Tables
Maintenance Tables
Reset the PM counter (SP7-804-001) after doing maintenance work.
2
Key: AN: As necessary / C: Clean + Inspect / R: Replace
Every
Every 45k Every 90k AN NOTE
120k
OPTICS
Air-using clean
Reflector C DO NOT clean with dry
cloth.
DRUM AREA
Transfer roller R
Discharge plate R
PAPER FEED
FUSING UNIT
17
2. Appendix: Preventive Maintenance Tables
Every
Every 45k Every 90k AN NOTE
120k
Hot roller R
Pressure roller R
Pressure-roller
C R
bushings
Inlet guide C C
Outlet guide C C
Thermistor C C
ARDF
18
3. Appendix: SP Mode Tables
SP1-XXX (Feed) 3
1001* LE Registration [–9.0 to 9.0 / 0.0 / 0.1 mm/step]
1003 4 Duplex
19
3. Appendix: SP Mode Tables
1105 7 Sets the additional temperature to SP1105-001’s degree for thick paper print.
1105 9 Sets the subtractive temperature to SP1105-001’s degree for thin paper print.
Thresh: S1 [0 to 50 / 16 / 1 °C/step]
20
System Service Mode
3
Judged as Low temp. Normal temp. High temp.
[0 to 30 / 10 / 1 °C/step]
1105 19 Low: Thick
The same function as SP1105 (-017 to -18)
1105 30 Waiting: Center Minus: Thick The same function as SP1105 (-024, -26)
21
3. Appendix: SP Mode Tables
22
System Service Mode
23
3. Appendix: SP Mode Tables
Check By-pass
1152 1
Execution type SP
SC Display [0 = No / 1 = Yes]
1159 1 Enables or disables consecutive jam detection at the fusing unit. If this SP is set to "1"
(default: 0), consecutive fusing jam alarm occurs (SC559) when the machine detects
three consecutive paper jams at the fusing unit.
1902 Frequency
Displays the fusing lamp power control frequency (as detected by the zero cross signal
1902 1
generator).
1907 20 F2 Tray
24
System Service Mode
SP2-XXX (Drum)
Adjusts the voltage applied to the charge roller for printing. The voltage changes
2001 1 automatically as charge-roller voltage control works. The value here is the base value
for the charge-roller voltage control.
The value from -1800 V to -1600 V is preferable.
25
3. Appendix: SP Mode Tables
2001 2 Adjusts the voltage applied to the charge roller for the ID sensor pattern (as part of
charge-roller voltage correction). Setting the same value as “SP2-201-002” is
preferable.
2001 3 Inputs the voltage value. Too small value may cause the charge roller tainted. Too large
value may cause attaching carrier particles in developer, on a printed paper. The value
3 from – 1800 V to 1600 V is preferable.
2103 3 Left
[0 to 4 / 2 / 0.1 mm/step]
2103 4 Right
2104 1 LD1
[60 to 140 / 100 / 0.1 %/step]
2104 2 LD2
26
System Service Mode
Pattern Select
LD Power Adj.
2152*
Adjusts each area LD power. Higher becomes stronger LD. Lower becomes dimmed.
27
3. Appendix: SP Mode Tables
28
System Service Mode
29
3. Appendix: SP Mode Tables
2201 1 Adjusts the voltage applied to the development roller for printing. Image density
becomes higher when you specify a smaller value (a greater absolute value). Image
density becomes lower when you specify a greater value (a smaller absolute value).
ID sensor pattern
[ 0 to 4 / 0 / 1 /step]
(0:N 1:H 2:L 3:HH 4:LL)
2201 2
Adjusts the toner density control of the developer case.
[0= Normal / 1= Thick / 2= Thin / 3= More thick / 4= More thin]
ID sensor pattern
2201 3 [-700 to -300 / -420 / 10 V/step]
(Temporally Input)
2211 1 This value affects how many sheets are copied continuously before PCU reversing.
30
System Service Mode
After “Toner Near End” detected, this value affects how many sheets are copied before
2213 1 “Toner End” will occur.
[0= 50 sheets / 1= 20 sheets]
2220 1 Vsp
2220 2 Vsg
3
2220 3 Vsdp Displays each value.
2220 4 Vt
2220 5 Vtref
[0 to 999 / 0 / 1 sheet/step]
2224 1
The counter applying to “SP2-213-1”
31
3. Appendix: SP Mode Tables
32
System Service Mode
2303 1 Positive
[0 to 20 / 10 / 1 A/step]
2303 2 Negative
0: OFF 1: ON
2308 1
The switch of the limiter for transfer voltage.
33
3. Appendix: SP Mode Tables
Initializes the developer and checks the TD sensor output (Vt). The machine mixes the
developer for 2 minutes while reading and displaying the Vt value. The machine does
2802 1 not initialize the TD sensor output. If the machine has not been used for a long period,
prints may have a dirty background. In a case like this, use this SP to mix the developer.
The message "Completed" is displayed when the program ends normally.
Supplies the toner to the development unit. The processing stops under either of the
following conditions:
2908 1
• The toner density in the development unit reaches the standard level.
• The processing has continued for two 2 minutes.
34
System Service Mode
Adjusts the toner supply time. The toner supply motor remains on for the specified time.
2922 1 Specify a greater value if the user tends to make many copies having high proportions of
solid black image areas.
Adjusts the toner supply time under the condition of “Toner End” or “Toner Near End”
2923 1
detected.
The ratio adjustment SP available only when “SP2-921-1” setting is “2 (Fixed1)”. Each
value represents as follows:
0: x1
1: x2
2: x4
2925 1
3: x8
4: x12
5: x16
6: Continuously supply
7: No supply
35
3. Appendix: SP Mode Tables
Adjusts Vts (the Vt value for new developer). The TD sensor output is adjusted to this
2926 1
value during the TD sensor initial setting process.
Determines whether the ID sensor signal is referenced or not for the toner density control.
2927 1
Keep the default value in usual operations.
Clears the following messages and counters without supplying the toner:
• Toner near end message
• Toner end message
2928 1 • Copies After Toner Near End Counter (SP2-224-001)
Do not use this SP in usual operations. When the toner in the development unit is
abnormally insufficient, the drum may attract the toner carrier to its surface. The toner
carrier damages the drum surface.
Adjusts the timing of toner supplying. The more frequently toner is supplied under the
2931 1
smaller value. DO NOT use this SP in usual operations.
36
System Service Mode
2933 1 For Adjustment of ID sensor correction value. DO NOT use this SP in usual operations.
Use this SP after ID Sensor replacement. This Operates PWM value clearing, Vsg re-
2935 1
adjustment, and PWM re-adjustment.
[0 to 999 / 0 / 1 page/step]
2936 1
The counter applying to “SP2-995-002”.
37
3. Appendix: SP Mode Tables
JobEnd / Interrupt -
2995 3
Sets the condition at which ID sensor control takes place.
Cleans or does not clean the transfer roller before each job. Select “1” if the backside of
the paper becomes unclean when output. Note that the copier takes a longer time to
2996 1
output the first copy when you select “1”. If you select “0”, the transfer roller is never
3 cleaned.
SP4-XXX (Scanner)
Adjusts the sub-scan magnification ( "Adjusting Copy Image Area" in the section
4008 1
"Replacement and Adjustment").
Adjusts the leading edge registration ( "Adjusting Copy Image Area" in the section
4010 1
"Replacement and Adjustment").
38
System Service Mode
Adjusts the side-to-side registration for scanning in platen mode ( "Adjusting Copy
4011 1
Image Area" in the section "Replacement and Adjustment").
4012 2 Book: Trailing Edge Adjusts the scanning margin. Generally, the scanning
margin should be as little as possible.
4012 3 Book: Left Side
3
4012 4 Book: Right Side
4013 2 Lamp On
4014 Scan
4016* DF Scan
39
3. Appendix: SP Mode Tables
Dust Check
4020*
3 DF dust check function
4020 3 0=OFF
The larger value is set, the stronger the correction becomes.
4400 2 Book Trailing Edge Adjusts the mask range against shade on each part
4400 3 Book Left of the original.
4400 8 Right
40
System Service Mode
3 18 Shading pattern
None
4 29 Thin line pattern
9 None 24 None
14 Color patch K
4429 1 Copying
The larger value, the stronger the density becomes
4429 2 Scanning
for coping originals forbidden to be duplicated.
4429 3 Fax Operation
4450 2 SH ON/OFF
4460 Digital AE
41
3. Appendix: SP Mode Tables
[0 to 15 / 8 / 1 /step]
005 MTF 0= (Off)
1 – 15= (Weak – Strong)
[0 to 7/ 4 / 1 /step]
006 Smoothing 0= (x1)
1 – 7= (Weak – Strong)
007 Brightness
[1 to 255 / 128 / 1 /step]
008 Contrast
[0 to 7/ 0 / 1 /step]
Ind Dot Erase
009 0= (x1)
(Independent Dot Erase)
1 – 7= (Weak – Strong)
42
System Service Mode
[0 to 7 / 4 / 1 /step]
006 Smoothing 0= (x1)
1 – 7= (Weak – Strong)
007 Brightness
[1 to 255 / 128 / 1 /step]
008 Contrast
[0 to 7 / 0 / 1 /step]
Ind Dot Erase
009 0= (Off)
(Independent Dot Erase)
1 – 7= (Weak – Strong)
[0 to 2 / 0 / 1 /step]
010 Texture Erase
0= (Fix)
4604* FGATE
43
3. Appendix: SP Mode Tables
44
System Service Mode
4624 2 Latest: BK O
4632 4 Latest: BK O
45
3. Appendix: SP Mode Tables
46
System Service Mode
3
4674* Black Level Adj. Display
47
3. Appendix: SP Mode Tables
4691 2 G Color1200
[0 to 1023 / 0 / 1 digit/step]
4691 3 BK E
4691 4 BK O
48
System Service Mode
4694 2 G Color1200
[0 to 1023 / 0 / 1 digit/step]
4694 3 BK E
4694 4 BK O
4810 3 Latest: Bk
49
3. Appendix: SP Mode Tables
50
System Service Mode
Adjusts the graduation level applying to copy application. Default (0) is optimal
4905 1
parameter.
51
3. Appendix: SP Mode Tables
[Dull 0 – 6 Sensitive]
4996 1
Adjusts the degree of white paper detection sensitivity.
52
System Service Mode
SP5-XXX (Mode)
001 • After selecting the number, you must turn the main power switch off and on.
Europe/Asia model: [0: mm / 1: inch]
American model: [0: mm / 1: inch] 3
5045* Accounting Counter
53
3. Appendix: SP Mode Tables
54
System Service Mode
Specifies the condition to reset the copy job settings when the key counter is removed.
• 0: Y = Yes: The settings are cleared when the counter is removed.
• 1: StdBy = Standby only: The settings are cleared when the counter is removed at
5120 1
the end of a job.
• 2: N = No: The settings are not cleared under either condition.
As for duplex copying, the job settings are always preserved regardless of these setting. 3
5121* Counter Up Timing [0 = Feed In / 1 = Exit]
[ 0 or 1 / 0 / – ]
001 CTL 0: Automatic printing
1: No automatic printing
CE Login
5169 If you change the printer bit switches, you must 'log in' to service mode with this SP before
you go into the printer SP mode.
[0 or 1 / 0 / - ]
001 CE Login CTL 0: Disabled
1: Enabled
55
3. Appendix: SP Mode Tables
5186 1 [1: Jam 0: None] in 10 sec after put the card out.
3 5195 Limitless SW [0 or 1 / 0]
56
System Service Mode
Set Time
Adjusts the RTC (real time clock) time setting for the local time zone.
Examples: For Japan (+9 GMT), enter 540 (9 hours x 60 min.)
DOM: +540 (Tokyo)
5302 NA :-300 (New York)
EU :+ 60 (Paris)
CH :+480 (Peking)
TW :+480 (Taipei) 3
AS :+480 (Hong Kong)
CTL
002 Time Difference [-1440 to 1440 / Area / 1 min./step ]
#
• Make sure that both SP5-307-3 and -4 are correctly set. Otherwise, this SP is not
activated even if this SP is set to "1".
57
3. Appendix: SP Mode Tables
Access Control
5401
When installing the SDK application, SAS (VAS) adjusts the following settings. DFU
58
System Service Mode
Clears the counts for the user codes assigned by the key operator to restrict the use of
001
the machine. Press [Execute] to clear.
Simplified Authentication
1: On
0: Off
59
3. Appendix: SP Mode Tables
Detail Option
Lockout On/Off
0: Off
1: On
Lockout Threshold
[1 to 10/5/1]
Cancellation On/Off
Determines whether the system waits the prescribed time for input of a correct user ID and
password after an account lockout has occurred.
003
[0 to 1/0/1]
0: Off (no wait time, lockout not cancelled)
1: On (system waits, cancels lockout if correct user ID and password are entered.
Cancellation Time
Determines the length of time that the system waits for correct input of the user ID and
004 password after a lockout has occurred. This setting is used only if SP5413-3 is set to "1"
(on).
[1 to 999/60/1 min.]
60
System Service Mode
Mitigation On/Off
Switches on/off masking of continuously used IDs and passwords that are identical.
001 [0 to 1/0/1]
0: Off
1: On
Mitigation Time 3
002 Sets the length of time for excluding continuous access for identical user IDs and
passwords.
[0 to 60/15/1 min.]
Permissible Number
001 Sets the number of attempts to attack the system with random passwords to gain illegal
access to the system.
[0 to 100/30/1 attempt]
Detect Time
002 Sets the time limit to stop a password attack once such an attack has been detected.
[1 to 10/5/1 sec.]
001 Limits the number of users used by the access exclusion and password attack detection
functions.
[50 to 200/200/1 users]
002 Limits the number of passwords used by the access exclusion and password attack
detection functions.
[50 to 200/200/1 passwords]
61
3. Appendix: SP Mode Tables
Monitor Interval
003 Sets the processing time interval for referencing user ID and password information.
[1 to 10/3/1 sec.]
3 001 Sets a limit on access attempts when an excessive number of attempts are detected for
MFP features.
[0 to 500/100/1]
002 Sets the length of time for monitoring the frequency of access to MFP features.
003 Sets the wait time to slow down the speed of certification when an excessive number of
access attempts have been detected.
[0 to 9/3/1 sec.]
004 Sets a limit on the number of requests received for certification in order to slow down the
certification speed when an excessive number of access attempts have been detected.
[50 to 200/200/1 attempt]
Copy
Determines whether certification is required before a user can use the copy applications.
001 [0 to 1/0/1]
0: On
1: Off
62
System Service Mode
Document Server
Determines whether certification is required before a user can use the document server.
011 [0 to 1/0/1]
0: On
1: Off
Fax
Determines whether certification is required before a user can use the fax application. 3
021 [0 to 1/0/1]
0: On
1: Off
Scanner
Determines whether certification is required before a user can use the scan applications.
031 [0 to 1/0/1]
0: On
1: Off
Printer
Determines whether certification is required before a user can use the printer applications.
041 [0 to 1/0/1]
0: On
1: Off
051 SDK1
[0 or 1/ 0 / 1] 0: ON. 1: OFF
061 SDK2 Determines whether certification is required before a user can use the
SDK application.
071 SDK3
63
3. Appendix: SP Mode Tables
Determines whether an error code appears in the system log after a user authentication
failure occurs.
001
[0 to 1/0/1]
0: Off
1: On
Panel Disp
3 Determines whether an error code appears on the operation panel after a user
authentication failure occurs.
002
[0 to 1/1/1]
1: On
0: Off
64
System Service Mode
001 SC Call
65
3. Appendix: SP Mode Tables
081 Homepage
ECS Debug SW
5793
DFU
Browser Debug
5794
DFU
66
System Service Mode
[Memory Clear]
5801
Before executing any of these SP codes, print an SMC Report.
All Clear
Turn the main power switch off and on after executing this SP.
Engine - -
002
Clears the engine settings. 3
SCS - -
003
Clears the system settings.
MCS -
005
Clears MCS data. DFU
Copier application
006
Clears the copier application settings.
Fax Application - -
007
Clears the fax application settings.
Printer Application - -
008
Clears the printer application settings.
Scanner Application - -
009
Clears the scanner application settings.
NCS
011
Initializes the NCS (Net Control Service) settings.
67
3. Appendix: SP Mode Tables
R-FAX - -
012 Initializes the job login ID, SmartNetMonitor for Admin, job history, and local storage
file numbers.
3 015
Initializes the UCS (User Information Control Service) settings.
CCS - -
017
Initializes the CCS (Certification and Charge-control Service) settings.
LCS - -
019
Initializes the LCS (Log Count Service) settings.
Web Apli - -
020
Initializes Web application settings.
ECS
021
Initializes ECS (Engine Control Service).
AICS
023
Initializes the AICS settings.
BROWSER
024
DFU
Websys - -
Input Check
5803
"Input Check" in this chapter.
68
System Service Mode
Output Check
5804
"Output Check" in this chapter.
5810 SC Reset
Service CTL -
001 Sets the telephone number for a service representative. This number is printed on the
Counter List, which can be printed with the user's "Counter" menu.
This can be up to 20 characters (both numbers and alphabetic characters can be input).
Facsimile CTL -
002 Sets the fax or telephone number for a service representative. This number is printed on
the Counter List.
This can be up to 20 characters (both numbers and alphabetic characters can be input).
Supply CTL -
003 Use this to input the telephone number of your supplier for consumables. Enter the
number and press"StringIn" key.
Press the "Clear modes" key to delete the telephone number.
Operation CTL -
004 Use this to input the telephone number of your sales agency. Enter the number and press
#.
Press the "Clear modes" key to delete the telephone number.
69
3. Appendix: SP Mode Tables
Use Proxy
062 This SP setting determines if the proxy server is used when the machine communicates
with the service center.
Proxy Host
This SP sets the address of the proxy server used for communication between embedded
RCG-N and the gateway. Use this SP to set up or display the customer proxy server
3 address. The address is necessary to set up embedded RCG-N.
063
• The address display is limited to 127 characters. Characters beyond the 127th
character are ignored.
• This address is customer information and is not printed in the SMC report.
This SP sets the port number of the proxy server used for communication between
embedded RCG N and the gateway. This setting is necessary to set up embedded RCG-
064
N.
• This port number is customer information and is not printed in the SMC report.
065
• The length of the name is limited to 31 characters. Any character beyond the 31st
character is ignored.
• This name is customer information and is not printed in the SMC report.
Proxy Password
066
• The length of the password is limited to 31 characters. Any character beyond the
31st character is ignored.
• This name is customer information and is not printed in the SMC report.
70
System Service Mode
CommLog Print
250
Prints the communication log.
71
3. Appendix: SP Mode Tables
3 bit3: SMB
bit4: BMLinkS
bit5: DIPRINT
bit6: (Reserved)
bit7: (Reserved)
72
System Service Mode
1 IPv6 17 WSD-Printer
5 AppleTalk 21 Reserve
087
6 DHCP 22 Bluetooth
73
3. Appendix: SP Mode Tables
74
System Service Mode
75
3. Appendix: SP Mode Tables
[000.000.000.000 to 255.255.255.255]
Primary srv IP address
Default: 000.000.000.000
101
Sets IP address to make a relation with PC designed as Capture server (CS). Normally,
the value is determined automatically on CS I/O device registration.
76
System Service Mode
[000.000.000.000 to 255.255.255.255]
Secondary srv IP address
Default: 000.000.000.000
111
Normally, the value is determined automatically on CS I/O device registration. Only IP
address designation is valid.
113
Secondary srv port number [1 to 65535 / 80 / 1 /step] 3
Normally, the value is determined automatically on CS I/O device registration.
The value affects the output resolution. See the list below.
Normally, the value is determined automatically on CS I/O device registration.
*When the resolution cannot be output for the machine specification limit, output is done
by the nearest rate within the limitation.
Value Resolution
0 600dpi
122
1 400dpi
2 300dpi
3 200dpi
4 150dpi
5 100dpi
6 75dpi
77
3. Appendix: SP Mode Tables
The value affects the resolution applying to capturing a monochrome original read by
Print application. See the list below.
Normally, the value is determined automatically on CS I/O device registration.
*When the resolution cannot be output for the machine specification limit, output is done
by the nearest rate within the limitation.
Value Resolution
3 124 0 600dpi
1 400dpi
2 300dpi
3 200dpi
4 150dpi
5 100dpi
6 75dpi
The value affects the resolution applying to capturing a monochrome original read by
Fax application. See the list below.
Normally, the value is determined automatically on CS I/O device registration.
*When the resolution cannot be output for the machine specification limit, output is done
by the nearest rate within the limitation.
Value Resolution
126 0 600dpi
1 400dpi
2 300dpi
3 200dpi
4 150dpi
5 100dpi
6 75dpi
78
System Service Mode
The value affects the resolution applying to capturing a colored original read by Scanner
application. See the list below.
Normally, the value is determined automatically on CS I/O device registration.
*When the resolution cannot be output for the machine specification limit, output is done
by the nearest rate within the limitation.
Value Resolution
127 0 600dpi
3
1 400dpi
2 300dpi
3 200dpi
4 150dpi
5 100dpi
6 75dpi
The value affects the resolution applying to capturing a monochrome original read by
Scanner application. See the list below.
Normally, the value is determined automatically on CS I/O device registration.
*When the resolution cannot be output for the machine specification limit, output is done
by the nearest rate within the limitation.
Value Resolution
128 0 600dpi
1 400dpi
2 300dpi
3 200dpi
4 150dpi
5 100dpi
6 75dpi
79
3. Appendix: SP Mode Tables
[1 to 11 or 13 / 11 or 13 / 1 /step]
Sets the maximum number of channels available for data transmission via Wireless LAN.
006 The number of channels available varies according to location. The default settings are
set for the maximum end of the range for each area. Adjust the upper 4 bits to set the
maximum number of channels. DFU
[ 1 to 11 or 13 / 1 / 1 /step]
Channel MIN CTL Europe: 1 to 13
NA/ Asia: 1 to 11
Sets the minimum number of channels available for data transmission via the wireless
007 LAN. The number of channels available varies according to location. The default settings
are set for the minimum end of the range for each area. Adjust the lower 4 bits to set the
minimum number of channels. DFU
80
System Service Mode
[00 to 11 / 00 / 1 binary]
00: Key #1
WEP Key Select CTL 01: Key #2 (Reserved)
011
10: Key #3 (Reserved)
11: Key #4 (Reserved)
[0 to 3 / 3 / 1]
WPA Debug Lyl CTL
1: Info, 2: Warning, 3: Error
045
Selects the debug log for WPA authentication application.
This SP is displayed only when the IEEE802.11 card is installed.
81
3. Appendix: SP Mode Tables
Setting 1 CTL
Bit Groups
1 Capture related
6 Repository related
Setting 2 CTL
Bit Groups
5844 USB
Vendor ID CTL
82
System Service Mode
Product ID CTL
Sets the device release number of the BCD (binary coded decimal) display.
004 [0000 to 9999/1] DFU
006 Use this setting to determine the length of time the prompt message is displayed when a
test error occurs during document transfer with the NetFile application and an external
device.
83
3. Appendix: SP Mode Tables
Range: 000.000.000.000 to
Server IP (Secondary)
255.255.255.255
008 Specifies the IP address assigned to the computer designated to function as the
secondary delivery server of Scan Router. This SP allows only the setting of the IP
address without reference to the DNS setting.
Allows changing the model of the delivery server registered by the I/O device.
009
3 0: Unknown, 1: SG1 Provided, 2: SG1 Package,
3: SG2 Provided, 4: SG2 Package
84
System Service Mode
[ 0 or 1 / 1 / - ]
Rapid Sending Control
022 0: Disable, 1: Enable
Enables or disables the prevention function for the continuous data sending.
85
3. Appendix: SP Mode Tables
003 Changes the maximum number of entries that UCS can handle.
If a value smaller than the present value is set, the UCS managed data is cleared, and the
data (excluding user code information) is displayed.
[0 or 1 / 0 / -]
021 Folder Auth change 0: Login user name
1: address book
86
System Service Mode
This SP moves the address book data from the SD card or flash ROM on the controller
board to the HDD. You must cycle the machine off and on after executing this SP.
1. Turn the machine off.
2. Install the HDD.
3. Turn the machine on.
4. Do SP5846 040.
5. Turn the machine off/on. 3
040
• • Executing this SP overwrites any address book data already on the HDD with the
• data from the flash ROM on the controller board.
• • We recommend that you back up all directory information to an SD card with
• SP5846-051 before you execute this SP.
• • After the address book data is copied to HDD, all the address book data is
• deleted from the flash ROM. If the operation fails, the data is not erased from the
• flash ROM.
This SP must be executed immediately after installation of an HDD unit in a basic machine
that previously had no HDD. The first time the machine is powered on with the new HDD
041 installed, the system automatically takes the address book from the NVRAM and writes it
onto the new HDD. However, the new address book on the HDD can be accessed only
by the system administrator at this stage. Executing this SP by the service technician
immediately after power on grants full address book access to all users.
Initialize All Setting & Addr Clears the local address book information, including
046
Book the user code.
Initialize All Delivery Addr Clears the distribution address book information,
048
Book except the user code.
87
3. Appendix: SP Mode Tables
051 Backup All Addr Book Uploads all directory information to the SD card.
3 052 Restore All Addr Book Downloads all directory information from the SD card.
88
System Service Mode
Note (1):
SP5846-062 to SP5846-065 do not normally require adjustment.
These SP modes are enabled only after the system administrator has set up a group password policy to
control access to the address book.
89
3. Appendix: SP Mode Tables
5848 SP5848-1 sets the 4-bit switch assignment for the access control setting. Setting of 0001
has no effect on access and delivery from Scan Router.
ac: Access Control
213 Primary Server These can be adjusted with the Web Image Monitor.
90
System Service Mode
Push [Execute] to download the fixed stamp data from the machine ROM onto the hard
disk. Then these stamps can be used by the system. If this is not done, the user will not
5853
have access to the fixed stamps ("Confidential", "Secret", etc.).
You must always execute this SP after replacing the HDD or after formatting the HDD.
Always switch the machine off and on after executing this SP.
91
3. Appendix: SP Mode Tables
[0 or 1 / 0 / 1/step]
002 Local Port CTL 0: Disallow
1: Allow
ON/OFF 0: OFF, 1: ON
001 Switches the debug log feature on and off. The debug log cannot be captured until this
3 feature is switched on.
Selects the destination where the debugging information generated by the event selected
by SP5858 will be stored if an error is generated
002
[2 to 3 /1]
2: HDD
3: SD Card
Save to HDD
005
Specifies the decimal key number of the log to be written to the hard disk.
Save to SD Card
006
Specifies the debug log number for saving to an SD card.
Takes the most recent 4 MB of the log written to the hard disk and copies them to the SD
009 Card.
A unique file name is generated to avoid overwriting existing file names on the SD Card.
Up to 4MB can be copied to an SD Card. 4 MB segments can be copied one by one to
each SD Card.
Takes the log of the specified key from the log on the hard disk and copies it to the SD
Card.
010
A unique file name is generated to avoid overwriting existing file names on the SD Card.
Up to 4 MB can be copied to an SD Card. 4 MB segments can be copied one by one to
each SD Card. This SP does not execute if there is no log on the HDD with no key
specified.
92
System Service Mode
Saves the specified debug log (with SP5-857-006) in memory to the SD card.
015
A unique file name is generated to avoid overwriting existing file names on the SD card.
Up to 4MB can be copied to the SD card. 4 MB segments can be copied one by one to
the SD card.
Make SD Debug
017
Executes the making of a file (4MB) for saving debug logs.
These SPs select the content of the debugging information to be saved to the destination
5858 selected by SP5857-2.
SP5858-3 stores one SC specified by number. Refer to the chapter "Trouble Shooting"
for a list of SC error codes.
93
3. Appendix: SP Mode Tables
3 0: OFF, 1: ON
001 Key 1
002 Key 2
003 Key 3
004 Key 4
005 Key 5 These SPs allow you to set up to 10 keys for log files for
functions that use common memory on the controller board.
006 Key 6 [ –9999999 to 9999999 / 0 / – ]
007 Key 7
008 Key 8
009 Key 9
010 Key 10
94
System Service Mode
020 Sets the amount of time to wait before saving mail that breaks up during reception. The
received mail is discarded if the remaining portion of the mail is not received during this
prescribed time.
021 Determines whether RFC2298 compliance is switched on for MDN reply mail.
0: No, 1: Yes
3
SMTP Auth. From Field Replacement [0 to 1 / 0 / – ]
022 Determines whether the FROM item of the mail header is switched to the validated
account after the SMTP server is validated.
0: No. "From" item not switched. 1: Yes. "From" item switched.
1: Internet Draft
2: RFC
95
3. Appendix: SP Mode Tables
001 Data Overwrite Security Enables the Data Overwrite Security unit. Press
"EXECUTE" on the operation panel. Then turn the
002 HDD Encryption machine off and on.
96
System Service Mode
5 DL function prohibition
DocSvr Format
Sets the way in which files in the document box are displayed.
This SP saves the counter list of the machine to an SD card in the slot 3.
001
The folder of "SD_COUNTER" must be made in an SD card for this SP.
97
3. Appendix: SP Mode Tables
001 SDK-1
002 SDK-2
003 SDK-3
004 SDK-4
3
005 SDK-5
006 SDK-6
Selects the brand name and production name for the Plug and Play function. These
names are stored in the NVRAM. When the NVRAM data is corrupted, select these
5907 1 names once again. Use the right-arrow or left-arrow key to scroll through the list of brand
names. To select a brand name, press the OK key. An asterisk (*) indicates which
manufacture is currently selected.
Sets the length of time to elapse before allowing another application to take control of
002 the display when the application currently controlling the display is not operating
because a key has not been pressed.
[3 to 30 / 3 / 1 second/step]
98
System Service Mode
Device Setting
5985 The NIC and USB support features are built into the GW controller. Use this SP to enable
and disable these features. In order to use the NIC and USB functions built into the
controller board, these SP codes must be set to "1".
[0 to 2 / 0 / 1 /step]
0: OFF, 1: ON, 2: ON: Limited
When the "Function limitation" is set, "On board NIC" is limited
only for the @Remote or LDAP/NT authentication. 3
001 On Board NIC
[0 or 1 / 0 / 1/step]
002 On Board USB
0: OFF, 1: ON
Gives the counter list text to the SD card inserted in the service slot.
001
In the SD card, the folder named “SD_COUNTER” must be placed in the root directory.
In the SP mode, press Copy Window to move to the copy screen, select the paper size,
5990 then press Start. Select A4/LT (Sideways) or larger to ensure that all the information
prints. Press SP Window to return to the SP mode, select the desired print, and press
"EXECUTE".
006 Non-Default (Prints only SPs set to values other than defaults.)
99
3. Appendix: SP Mode Tables
022 Scanner SP
026 Printer SP
SP Text Mode
5992
This SP gives the SMC print text data to SD card inserted.
006 Non-Default (Prints only SPs set to values other than defaults.)
022 Scanner SP
026 Printer SP
5994 Mirroring
100
System Service Mode
SP6-XXX (Peripherals)
ADF Adjustment ( "DF Image Adjustment" in the "Adjusting Copy Image Area") 3
6006*
NOTE: Available menus depend on the machine model and its configuration.
003 Leading Edge Duplex Front [–5.0 to +5.0 / 0.0 / 0.1 mm/step]
004 Leading Edge Duplex Rear [–5.0 to +5.0 / 0.0 / 0.1 mm/step]
Displays ADF sensor information. When the cover opens, this SP’s value becomes “1”.
101
3. Appendix: SP Mode Tables
Makes the paper feed solenoid intermittent-drive to check ADF condition against
operational load.
001 [0 to 3 / 3 / 1 Sheet(s)/step]
102
System Service Mode
Adjusts the interval used for the shading processing in the ARDF mode. Light and heat in
001 the room may affect the scanner response. Reduce this setting if copy quality indicates
that the white level is drifting during ARDF copy jobs.
Total SC Counter
002 Displays how many times SC codes are generated including the number having been
reset.
7403* SC History
001 Latest
002 Latest 1
003 Latest 2
004 Latest 3
005 Latest 4
Displays the most recent 10 service calls.
006 Latest 5
007 Latest 6
008 Latest 7
009 Latest 8
010 Latest 9
103
3. Appendix: SP Mode Tables
001 Original Jam Counter Displays the total number of original jams.
At power on
001
Paper jam occurs at power on.
104
System Service Mode
Displays the total number of original jams by location. These jams occur when the
original does not activate the sensors.
7505 Note
• Lag. Jam occurs when the paper remains at the sensor for longer than the
prescribed time.
• Late: Jam occurs because paper fails to arrive at the prescribed time.
006 A5 LEF
133 A4 SEF
134 A5 SEF
Displays the number of jams according to the paper size.
142 B5 SEF CTL
[ 0 to 9999 / 0 / 1 sheet/step ]
164 LG SEF
166 LT SEF
255 Others
105
3. Appendix: SP Mode Tables
001 Latest
002 Latest 1 Displays the copy jam history (the most recent 10 jams)
010 Latest 9
106
System Service Mode
001 Latest
002 Latest 1 Displays the original jam history (the most recent 10 jams).
010 Latest 9
[0: No / 1: Yes]
001 Determines whether the use of PM applies to the machine or not. After selecting “Yes”
(1), confirm the “SP5067” (Parts replacement operation type) setting.
255 Displays the parts number and versions of all ROMs in the machine.
Distance (mm)
004 Displays the PM distance Counter (45k).
45k
Distance (mm)
005 Displays the PM distance Counter (90k).
90k
107
3. Appendix: SP Mode Tables
[0 to 255 / 0 / 1 /step]
006 Distance 45k part
Displays the PM distance Counter (45k) usage rate.
[0 to 255 / 0 / 1 /step]
007 Distance 90k part
Displays the PM distance Counter (90k) usage rate.
Paper
3 001 Resets the PM counter (SP7-803-001). When the program ends normally, the message
"Completed" is displayed.
Resets the SC, paper, original, and total jam counters. When the program ends
001 normally, the message "Completed" is displayed.
SP7-807-1 does not clear the latest 10 JAM and SC logs.
MF Error Counter
7826
Displays the number of counts requested of the card/key counter.
A request for the count total failed at power on. This error
001 Error Counter
will occur if the device is installed but disconnected.
The request for a staple count failed at power on. This error
002 Error Staple
will occur if the device is installed but disconnected.
Displays the SC codes and the number of their occurrences. Each number is in the range
001
of 0 to 9999.
108
System Service Mode
3
Assert Info
7901 Records the location where a problem is detected in the program. The data stored in this
SP is used for problem analysis.
003 Location - -
004 Distance (mm) 45k part Displays each of the PM distance Counter: the last
005 Distance (mm) 90k part count
006 Distance 45k Displays each of the PM distance Counter usage rate:
007 Distance 90k the last count
002 Sheets 45k part Displays each of the PM sheet Counter (90k): the
003 Sheets 90k part second last count
004 Distance (mm) 45k part Displays each of the PM distance Counter: the second
005 Distance (mm) 90k part last count
109
3. Appendix: SP Mode Tables
006 Distance 45k Displays each of the PM distance Counter usage rate:
007 Distance 90k the second last count
002 Sheets 45k part Displays each of the PM sheet Counter (90k): the third
003 Sheets 90k part last count
3 004 Distance (mm) 45k part Displays each of the PM distance Counter: the third last
005 Distance (mm) 90k part count
006 Distance 45k Displays each of the PM distance Counter usage rate:
007 Distance 90k the third last count
Most of the SPs in this group are prefixed with a letter that indicates the mode of operation (the mode of
operation is referred to as an "application"). Before reading the Group 8 Service Table, make sure that
you understand what these prefixes mean.
C: Copy application.
F: Fax application. Totals (pages, jobs, etc.) executed for each application
P: Print application. when the job was not stored on the document server.
S: Scan application.
110
System Service Mode
The Group 8 SP codes are limited to 17 characters, forced by the necessity of displaying them on the
small LCDs of printers and faxes that also use these SPs. Read over the list of abbreviations below and
refer to it again if you see the name of an SP that you do not understand.
Key for Abbreviations
3
Abbreviation What it means
Apl Application
Bk Black
C Cyan
Comb Combine
Comp Compression
Deliv Delivery
Emul Emulation
FC Full Color
111
3. Appendix: SP Mode Tables
Get Print Counter. For jobs 10 pages or less, this counter does not count
up. For jobs larger than 10 pages, this counter counts up by the number
GPC
that is in excess of 10 (e.g., for an 11-page job, the counter counts up
11-10 =1)
3 IFax Internet Fax
Image Edit performed on the original with the copier GUI, e.g. border
ImgEdt
removal, adding stamps, page numbers, etc.
K Black (YMCK)
Mag Magnification
Print Job Manager/Desk Top Editor: A pair of utilities that allows print
jobs to be distributed evenly among the printers on the network, and
Palm 2
allows files to moved around, combined, and converted to different
formats.
PC Personal Computer
Pages. A page is the total scanned surface of the original. Duplex pages
PGS count as two pages, and A3 simplex count as two pages if the A3/DLT
counter SP is switched ON.
Ppr Paper
112
System Service Mode
Red (Toner Remaining). Applies to the wide format model A2 only. This
R
machine is under development and currently not available.
Rez Resolution
S-to-Email Scan-to-E-mail
SMC report printed with SP5990. All of the Group 8 counters are
SMC
recorded in the SMC report.
Svr Server
• All of the Group 8 SPs are reset with SP5 801 1 Memory All Clear.
113
3. Appendix: SP Mode Tables
• SP 8 191 to 8 196 count the number of scanned sides of pages, not the number of physical pages.
• These counters do not count reading user stamp data, or reading color charts to adjust color.
• Previews done with a scanner driver are not counted.
• A count is done only after all images of a job have been scanned.
• Scans made in SP mode are not counted.
Examples
• If 3 B5 pages and 1 A3 page are scanned with the scanner application but not stored, the S: count
is 4.
• If both sides of 3 A4 sheets are copied and stored to the document server using the Store File
button in the Copy mode window, the C: count is 6 and the L: count is 6.
• If both sides of 3 A4 sheets are copied but not stored, the C: count is 6.
• If you enter document server mode then scan 6 pages, the L: count is 6.
These SPs count the total number of large pages input with the scanner for scan and
8 201 copy jobs. Large size paper (A3/DLT) scanned for fax transmission is not counted.
• These counters are displayed in the SMC Report, and in the User Tools display.
114
System Service Mode
These SPs count the total number of large pages input with the scanner for scan jobs
8 205 only. Large size paper (A3/DLT) scanned for fax transmission is not counted.
• These counters are displayed in the SMC Report, and in the User Tools display.
• When 1 sheet is fed for duplex scanning the Front count is 1 and the Back count is 1.
• If a jam occurs during the job, recovery processing is not counted to avoid double counting. Also,
the pages are not counted if the jam occurs before the first sheet is output.
115
3. Appendix: SP Mode Tables
8 281 T:Scan PGS/TWAIN CTL These SPs count the number of pages
scanned using a TWAIN driver. These
counters reveal how the TWAIN driver is
used for delivery functions.
[0 to 99999999 / 0 / 1]
8 285 S:Scan PGS/TWAIN CTL
8 301 These SPs count by size the total number of pages scanned by all applications. Use
these totals to compare original page size (scanning) and output (printing) page size
[SP 8-441].
8 302 These SPs count by size the total number of pages scanned by the Copy application.
Use these totals to compare original page size (scanning) and output (printing) page
size [SP 8-442].
8 303 These SPs count by size the total number of pages scanned by the Fax application.
Use these totals to compare original page size (scanning) and output page size [SP
8-443].
8 305 These SPs count by size the total number of pages scanned by the Scan application.
Use these totals to compare original page size (scanning) and output page size [SP
8-445].
8 306 The L: counters work differently case by case. Sometimes, they count jobs/pages
stored on the document server Sometimes, they include occasions when the user uses
a file that is already on the document server.
116
System Service Mode
001 A3
002 A4
003 A5
004 B4
005 B5
006 DLT
- 3
007 LG
008 LT
009 HLT
8 382 C:Total PrtPGS CTL These SPs count the number of pages
8 383 F:Total PrtPGS CTL printed by the customer. The counter for the
application used for storing the pages
8 384 P:Total PrtPGS CTL increments.
• When the A3/DLT double count function is switched on with SP5104, 1 A3/DLT page is counted
as 2.
• When several documents are merged for a print job, the number of pages stored is counted for the
application that stored them.
• These counters are used primarily to calculate charges on use of the machine, so the following
pages are not counted as printed pages:
Blank pages in a duplex printing job.
Blank pages inserted as document covers, chapter title sheets, and slip sheets.
Reports printed to confirm counts.
117
3. Appendix: SP Mode Tables
All reports done in the service mode (service summaries, engine maintenance reports, etc.)
Test prints for machine image adjustment.
Error notification reports.
Partially printed pages as the result of a copier jam.
These SPs count pages printed on paper sizes A3/DLT and larger.
8 391
3 • In addition to being displayed in the SMC Report, these counters are also
displayed in the User Tools display on the copy machine.
118
System Service Mode
8 426 The L: counters work differently case by case. Sometimes, they count jobs/pages
stored on the document server Sometimes, they include occasions when the user uses a
file that is already on the document server.
012 Booklet -
013 Magazine -
014 2in1+Booklet -
015 4in1+Booklet -
016 6in1+Booklet -
017 8in1+Booklet -
018 9in1+Booklet -
019 2in1+Magazine -
020 4in1+Magazine -
119
3. Appendix: SP Mode Tables
021 6in1+Magazine -
022 8in1+Magazine -
023 9in1+Magazine -
024 16in1+Magazine -
• These counts (SP8-421 to SP8-427) are especially useful for customers who need to improve their
compliance with ISO standards for the reduction of paper consumption.
3 • Pages that are only partially printed with the n-Up functions are counted as 1 page.
• Here is a summary of how the counters work for Booklet and Magazine modes:
Booklet Magazine
Original Original
Count Count
Pages Pages
1 1 1 1
2 2 2 2
3 2 3 2
4 2 4 2
5 3 5 4
6 4 6 4
7 4 7 4
8 4 8 4
120
System Service Mode
8 446 The L: counters work differently case by case. Sometimes, they count jobs/pages
stored on the document server Sometimes, they include occasions when the user uses
a file that is already on the document server.
001 A3
002 A4
003 A5
004 B4
005 B5
-
006 DLT
007 LG
008 LT
009 HLT
121
3. Appendix: SP Mode Tables
These SPs count by paper type the number pages printed by all applications.
• These counters are not the same as the PM counter. The PM counter is based on
8 461 feed timing to accurately measure the service life of the feed rollers. However,
these counts are based on output timing.
• Blank sheets (covers, chapter covers, slip sheets) are also counted.
• During duplex printing, pages printed on both sides count as 1, and a page
printed on one side counts as 1.
122
System Service Mode
8 466 The L: counters work differently case by case. Sometimes, they count jobs/pages
stored on the document server Sometimes, they include occasions when the user uses
a file that is already on the document server.
001 Normal
002 Recycled
003 Special
004 Thick
007 OHP
008 Other
001 RPCS
002 RPDL
003 PS3
004 R98
123
3. Appendix: SP Mode Tables
005 R16
006 GL/GL2
007 R55
008 RTIFF
009 PDF
010 PCL5e/5c
3
011 PCL XL
012 IPDL-C
013 BM-Links
014 Other
015 IPDS
These SPs count by finishing mode the total number of pages printed by the Fax
8 523 application.
• Print finishing options for received faxes are currently not available.
124
System Service Mode
8 526 The L: counters work differently case by case. Sometimes, they count jobs/pages
stored on the document server Sometimes, they include occasions when the user uses
a file that is already on the document server.
001 Sort
3
002 Stack
003 Staple
004 Booklet
005 Z-Fold
006 Punch
007 Other
008 Inside-Fold
009 Three-IN-Fold
010 Three-OUT-Fold
011 Four-Fold
012 KANNON-Fold
013 Perfect-Bind
014 Ring-Bind
• If stapling is selected for finishing and the stack is too large for stapling, the unstapled pages are
still counted.
• The counts for staple finishing are based on output to the staple tray, so jam recoveries are
counted.
125
3. Appendix: SP Mode Tables
Staples
8 531
-
8 556 The L: counters work differently case by case. Sometimes, they count jobs/pages
stored on the document server Sometimes, they include occasions when the user uses
a file that is already on the document server.
001 Perfect-Bind
002 Ring-Bind
8 566 The L: counters work differently case by case. Sometimes, they count jobs/pages
stored on the document server Sometimes, they include occasions when the user uses
a file that is already on the document server.
126
System Service Mode
8 581 This SP counts the total output broken down by color output, regardless of the
application used. In addition to being displayed in the SMC Report, these counters
are also displayed in the User Tools display on the copy machine.
001 Total
001 A3/DLT These SPs count the totals for A3/DLT paper use,
number of duplex pages printed, and the number of
002 Duplex staples used. These totals are for Other (O:)
applications only.
011 B/W Printing Pages Displays the number of the printouts in each mode.
001 B/W
001 B/W
001 B/W
127
3. Appendix: SP Mode Tables
001 B/W
001 B/W
• If a document has color and black-and-white pages mixed, the pages are counted separately as
B/W or Color.
• At the present time, this feature is provided for the Fax application only so SP8631 and SP8633
are the same.
• The counts include error pages.
• If a document is sent to more than one destination with a Group transmission, the count is done for
each destination.
• Polling transmissions are counted but polling RX are not.
• Relay, memory, and confidential mailbox transmissions and are counted for each destination.
128
System Service Mode
001 B/W
• If a document has color and black-and-white pages mixed, the pages are counted separately as
B/W or Color.
• At the present time, this feature is provided for the Fax application only so SP8641 and SP8643
are the same.
3
• The counts include error pages.
• If a document is sent to more than one destination with a Group transmission, the count is done for
each destination.
• Polling transmissions are counted but polling RX are not.
• Relay, memory, and confidential mailbox transmissions and are counted for each destination.
001 B/W
002 Color
• The count for B/W and Color pages is done after the document is stored on the HDD. If the job is
cancelled before it is stored, the pages are not counted.
• If Scan-to-Email is used to send a 10-page document to 5 addresses, the count is 10 (the pages
are sent to the same SMTP server together).
• If Scan-to-PC is used to send a 10-page document to 5 folders, the count is 50 (the document is
sent to each destination of the SMB/FTP server).
• Due to restrictions on some devices, if Scan-to-Email is used to send a 10-page document to a
large number of destinations, the count may be divided and counted separately. For example, if a
10-page document is sent to 200 addresses, the count is 10 for the first 100 destinations and the
count is also 10 for the second 100 destinations, for a total of 20.).
129
3. Appendix: SP Mode Tables
3 001 B/W
002 Color
• The B/W and Color counts are done after the document is stored on the HDD of the Scan Router
server.
• If the job is canceled before storage on the Scan Router server finishes, the count is not done.
• The count is executed even if there is confirmation of the arrival at the Scan Router server.
001 B/W
002 Color
• Print jobs done with Web Image Monitor and Desk Top Binder are added to the count.
• If several documents are merged for sending, the number of pages stored is counted for the
application that stored them.
• When several documents are sent by a Fax broadcast, the F: count is done for the number of
pages sent to each destination.
130
System Service Mode
8 681 T:PCFAX TXPGS CTL These SPs count the number of pages sent by PC
Fax. These SPs are provided for the Fax
application only, so the counts for SP8-681 and
8 683 F:PCFAX TXPGS CTL SP8-683 are the same.
[0 to 99999999 / 0 / 1]
• This counts pages sent from a PC using a PC fax application, from the PC through the copier to the
destination.
• When sending the same message to more than one place using broadcasting, the pages are only
counted once. (For example, a 10-page fax is sent to location A and location B. The counter goes
3
up by 10, not 20.)
8 701 These SPs count the number of pages sent by the physical port used to send them. For
example, if a 3-page original is sent to 4 destinations via ISDN G4, the count for
ISDN (G3, G4) is 12.
001 PSTN-1 -
002 PSTN-2 -
003 PSTN-3 -
005 Network -
-001 JPEG/JPEG2000 -
-003 PDF -
-004 Other -
-005 PDF/Comp -
-006 PDF/A -
131
3. Appendix: SP Mode Tables
-001 B/W -
-002 Color -
3
RX PGS/Port [0 to 9999999/ 0 / 1]
8741 These SPs count the number of pages received by the physical port used to receive
them.
001 PSTN-1
002 PSTN-2
003 PSTN-3
005 Network
001 Total
001 BK
132
System Service Mode
This SP displays the percent of toner remaining for each color. This SP allows the user
to check the toner supply at any time.
8 801
• This precise method of measuring remaining toner supply (1% steps) is better
than other machines on the market that can only measure in increments of 10
(10% steps).
001 K 3
8 811 Eco Counter CTL
004 Duplex
005 Combine
108 Duplex(%):Last
109 Combine(%):Last
011 0-2%:Bk
021 3-4%: Bk
133
3. Appendix: SP Mode Tables
031 5-7%: Bk
041 8-10%: Bk
3 001 Bk
001 Bk
001 Bk
001 Bk
001 Bk
134
System Service Mode
001 Bk
[0 to 2147483647 / 0 / 1]
001 Coverage(%): BK These SPs display the total coverage percentage of sheets
output by the machine.
[0 to 99999999 / 0 / 1]
011 Coverage/P: Bk These SPs display the total coverage pages output by the 3
machine.
8 941 These SPs count the amount of time the machine spends in each operation mode. These
SPs are useful for customers who need to investigate machine operation for
improvement of their compliance with ISO Standards.
007 PrtJam Total down time due to paper jams during printing.
008 OrgJam Total down time due to original jams during scanning.
009 Supply PM Unit End Total down time due to toner end.
135
3. Appendix: SP Mode Tables
001 Total -
003 Copy: BW -
007 Printer: BW -
010 FaxP: BW -
013 Duplex -
101 SedTtl: FC -
102 SendTtl: BW -
103 FaxSend -
104 FaxSend: BW -
105 FaxSend: BW -
136
System Service Mode
SP-9XXX (Etc)
001 0: NOT SET 1: SET Selects the right door open/close SW ON/OFF
[0 to 99 / 17 / 1 mm/step ]
010 Heater Force OFF Timing Sets the forced the heater OFF time after paper- 3
through.
[0 to 50 / 16 / 1 deg/step ]
Thresh: Warming-up Low
011 Sets the basic temperature for determination of the
Temperature
condition on machine-startup.
[0 to 999 / 5 / 1 sec/step ]
012 Disable Change Time
Unused. DO NOT change the setting.
[0 to 999 / 15 / 1 sec/step ]
When the wait time is over this SP’s time, the following
three items are reset:
013 Total Count Clear Time
• Control cycle on printing,
• Repeat-temperature correction,
• CPM-down counter
[0 to 999 / 60 / 1 sec/step ]
014 Print Prepare Time
Sets the print preparation time.
137
3. Appendix: SP Mode Tables
138
System Service Mode
139
3. Appendix: SP Mode Tables
This SP’s count is used as the flag of toner bottle replacement notice.
008 When the value becomes more than 1000, the notice will occur and the value will be
cleared.
9947 Fuser SC
140
System Service Mode
141
3. Appendix: SP Mode Tables
142
System Service Mode
1. Select SP5-803.
2. Select the number (see the table below) corresponding to the component.
3. Select "Start" The copy mode is activated.
4. The sign "01H" or "00H" is displayed (see the table below).
143
3. Appendix: SP Mode Tables
144
System Service Mode
1. Select SP5-804.
2. Select the number (see the table below) corresponding to the component.
3. Select "ON."
4. To stop the operation, select "OFF."
Num. Component
032 Registration CL
145
3. Appendix: SP Mode Tables
Num. Component
047 P Sensor
3
048 Anti-static LED
051 LD
When checking Fan Motor High (005) or Fan Motor Low (006) note the following:
• These motors may not respond when the fusing temperature is high.
• Selecting "ON" checks that one of these motors normally operates. Selecting "OFF" turns off the
motor that you have started by selecting "ON." However, this does not guarantee that the motor
normally stops during normal operation.
146
System Service Mode
bit 0 DFU - -
3
bit 1 DFU - -
bit 2 DFU - -
Enables/Disables MFP I/O Timeouts. Enabled: The MFP I/O Timeout setting will
have no affect. I/O Timeouts will never occur.
Enabled: Print jobs will be saved to an SD Card in the GW SD slot ( "Card Save
Function" in the service tables of Field Service Manual).
bit 5 DFU - -
bit 6 DFU - -
Enable: The machine prints all RPCS and PCL jobs with a border on the edges of the
printable area.
147
3. Appendix: SP Mode Tables
bit 0 DFU - -
bit 1 DFU - -
A collation type (shift or normal) will be applied to all jobs that do not already have
a 'Collate Type' configured.
3
• If #5-0 is enabled, this Bit Switch has no effect.
bit 4 DFU - -
bit 5 DFU - -
bit 6 DFU - -
bit 7 DFU - -
148
System Service Mode
bit 0 DFU - -
bit 1 DFU - -
Enabled: Uses the same left margin as older HP models such as HP4000/HP8000.
In other words, the left margin defined in the job (usually "<ESC>*r0A") will be
changed to "<ESC>*r1A" 3
bit 3 DFU - -
bit 4 DFU - -
bit 5 DFU - -
bit 6 DFU - -
bit 7 DFU - -
149
3. Appendix: SP Mode Tables
bit 0 DFU - -
If a paper size or type mismatch occurs during the printing of multiple copies, only a
single copy is output by default. Using this BitSw, the device can be configured to
3 print all copies even if a paper mismatch occurs.
bit 2 DFU - -
bit 4 Increase max number of the stored jobs to 1000 Disable Enable
jobs. (100) (1000)
Enabled: Changes the maximum number of jobs that can be stored on the HDD via
Job Type settings to 1000. The default is 100.
bit 5 DFU - -
Enabled: The image rotation will be performed as they were in the specifications of
older models for the binding of pages of mixed orientation jobs. The old models are
below:
-PCL-: Pre-04A models
Routes all pages through the duplex unit. If this is disabled, simplex pages or the last
page of an odd-paged duplex job, are not routed through the duplex unit. This could
result in problems with letterhead / pre-printed pages.
150
System Service Mode
bit 0 DFU - -
bit 1 DFU - -
bit 2 DFU - -
bit 3 DFU - -
bit 4 DFU - -
bit 5 DFU - -
bit 6 DFU - -
bit 7 DFU - -
151
3. Appendix: SP Mode Tables
The following SP modes are located in the system SP mode. Refer to section 5.1 of the main unit service
manual.
3 SP No. Description Function and Setting
Resets data for process control and all software counters, and
5801
Memory All Clear returns all modes and adjustments to their defaults values.
-001
Section "Memory Clear" in this chapter for details.
Plug & Play Maker/ Selects the brand name and the production name for Windows
5907
Model Name Plug & Play. This information is stored in NVRAM.
Self-Diagnose Result
7832 Displays the controller self-diagnostic result.
Display
[range / default / Example: [-9 to +9 / +3.0 / 0.1 mm step]. The setting can be adjusted in the
step] range ±9, value reset to +3.0 after an NVRAM reset, and the value can be
changed in 0.1 mm steps with each key press.
* This value is stored in NVRAM. After a RAM reset, the default value (factory
setting) is restored.
152
System Service Mode
1005* 1 Erase Margin (Remote Creates an erase margin for all edges of the scanned
Scan) Range from 0 to 5 image.
mm The margin color (Black or White) depends on color-
tone and invert settings. 3
[0 to 5 / 0mm / 1mm step]
1009* 1 Remote Scan disable Enables or disables the network TWAIN scanner
function.
[0: Enable, 1: Disable]
1010* 1 Non Display ClearLight Sets the clear light PDF display ON/OFF
PDF [0: OFF 1: ON]
1011* 1 Org Count Disp Sets the original counter display ON/OFF
[0: OFF 1: ON]
1012 1 User Info Release Clears or does not clear user information after a job.
[0 or 1 / 1 / - ]
0: Not clear, 1: Clear
1013 2 Scan to Media Device Sets "Scan To Multi Media" function ON/OFF.
Setting [0 or 1 / 1 / - ]
0: OFF, 1: ON
Comp1:
5-95
1 [5 to 95 / 20 / 1/step]
(Middle I-
Qual)
153
3. Appendix: SP Mode Tables
Comp2:
5-95
2 [5 to 95 / 40 / 1/step]
(High I-
Qual)
Comp3:
5-95
3 [5 to 95 / 65 / 1/step]
(Low I-
3 Qual)
Comp4:
5-95
4 [5 to 95 / 80 / 1/step]
(Highest I-
Qual)
Comp5:
5-95
5 [5 to 95 / 95 / 1/step]
(Lowest I-
Qual)
2024 These SP codes set the compression ratio for the clear light PDF processing mode.
Range: 5 (lowest ratio) 95 (highest ratio)
2025 These SP codes set the compression ratio for the clear light PDF processing mode (For
JPEG 2000).
Range: 5 (lowest ratio) 95 (highest ratio)
154
System Service Mode
For the settings of the image quality, see the copier SP-mode table.
155
3. Appendix: SP Mode Tables
156
4. Appendix: Fax Troubleshooting
Guide
157
4. Appendix: Fax Troubleshooting Guide
158
Fax Error Codes
159
4. Appendix: Fax Troubleshooting Guide
160
Fax Error Codes
161
4. Appendix: Fax Troubleshooting Guide
The called terminal fell back to • The terminal could not detect ANSam.
T.30 mode, because it could
0-75 • Check the line connection and condition.
not detect a CM in response to
ANSam (ANSam timeout). • Try receiving a call from another V.8/V.34 fax.
The calling terminal fell back to • The called terminal could not detect a CM due to
T.30 mode, because it could noise, etc.
0-76 not detect a JM in response to
CM • Check the line connection and condition.
162
Fax Error Codes
The called terminal detected • Check for line noise or other line problems.
0-79 CI while waiting for a V.21 • If this error occurs, the called terminal falls back to T.
signal. 30 mode.
The line was disconnected due • The guard timer expired while starting these phases.
0-80 to a timeout in V.34 phase 2 – Serious noise, narrow bandwidth, or low signal level
line probing. can cause these errors.
If these errors happen at the transmitting terminal:
The line was disconnected due
0-81 to a timeout in V.34 phase 3 – • Try making a call at a later time.
equalizer training. • Try using V.17 or a slower modem using dedicated
tx parameters.
4
The line was disconnected due
0-82 to a timeout in the V.34 phase • Try increasing the tx level.
4 – control channel start-up. • Try adjusting the tx cable equalizer setting.
If these errors happen at the receiving terminal:
The line was disconnected due • Try adjusting the rx cable equalizer setting.
0-83 to a timeout in the V.34 control • Try increasing the tx level.
channel restart sequence. • Try using V.17 or a slower modem if the same error
is frequent when receiving from multiple senders.
The line was disconnected due • The signal did not stop within 10 s.
to abnormal signaling in V.34
0-84 • Turn off the machine, then turn it back on.
phase 4 – control channel
start-up. • If the same error is frequent, replace the FCU.
The line was disconnected due • The signal did not stop within 10 s.
0-85 to abnormal signaling in V.34 • Turn off the machine, then turn it back on.
control channel restart. • If the same error is frequent, replace the FCU.
163
4. Appendix: Fax Troubleshooting Guide
JBIG compression or
2-23 • Turn off the machine, then turn it back on.
reconstruction error
2-24 JBIG ASIC error • Turn off the machine, then turn it back on.
• FCU defective
2-29 JBIG trailing edge maker error
• Check the destination device.
The machine resets itself for a • If this is frequent, update the ROM, or replace the
2-50
fatal FCU system error FCU.
164
Fax Error Codes
165
4. Appendix: Fax Troubleshooting Guide
166
Fax Error Codes
SIP authentication password • The input password for the authentication does not
13-24
error match the password registered in the SIP server.
167
4. Appendix: Fax Troubleshooting Guide
168
Fax Error Codes
169
4. Appendix: Fax Troubleshooting Guide
Cancelled the Mail Due to • Error detected with NFAX and send was cancelled
14-32
Error Detected by NFAX due to a software error.
No Mail Address For the • Neither the mail address of the machine nor the mail
14-33
Machine address of the network administrator is registered.
170
Fax Error Codes
Transmission Error due to the • When the 0 line page exists in received pages with
14-62
existence of zero line page G3 communication, the transmission is interrupted.
POP3/IMAP4 Mail Account • The POP3/IMAP4 mail account has not been
15-02
Information Not Registered registered.
15-03 Mail Address Not Registered • The mail address has not been registered.
15-10 DCS Mail Receive Error • Error other than 15-11 to 15-18.
171
4. Appendix: Fax Troubleshooting Guide
15-16 Mail Size Receive Error • The mail cannot be received because it is too large.
15-18 Incomplete Mail Received • Only one portion of the mail was received.
172
Fax Error Codes
15-61 Attachment File Format Error • The attached file is not TIFF format. 4
Could not receive transmission due to:
• Resolution error
• Image of resolution greater than 200 dpi without
extended memory.
• Resolution is not supported.
15-62 TIFF File Compatibility Error
• Page size error
• The page size was larger than A3.
• Compression error
• File was compressed with other than MH, MR, or
MMR.
173
4. Appendix: Fax Troubleshooting Guide
174
Fax Error Codes
No G3 parameter
22-05 • Defective FCU board or firmware.
confirmation answer
175
4. Appendix: Fax Troubleshooting Guide
IFAX Troubleshooting
• Use the following procedures to determine whether the machine or another part of the network is
causing the problem.
Communication
Item Action [Remarks]
Route
4 2. LAN activity
• Check that other devices connected to the LAN
can communicate through the LAN.
176
IFAX Troubleshooting
Communication
Item Action [Remarks]
Route
Between machine • Make sure that the client devices which have
and e-mail server an account in the server can send/receive e-
mail.
2. E-mail server
[Ask the administrator to check. 4
Send a test e-mail with the machine’s own number
as the destination. The machine receives the
returned e-mail if the communication is performed
successfully.]
177
4. Appendix: Fax Troubleshooting Guide
Communication
Item Action [Remarks]
Route
178
IP-Fax Troubleshooting
IP-Fax Troubleshooting
IP-Fax Transmission
7 Specified port number correct? Confirm the port number of the remote fax.
10 Remote fax switched off or busy? Check that the remote fax is switched on.
179
4. Appendix: Fax Troubleshooting Guide
10 DNS registered when host name specified? Contact the network administrator.
180
IP-Fax Troubleshooting
10 IP address of local fax registered? Register the IP address of the local fax.
11 Alias number of local fax registered? Register the Alias number of the local fax.
181
4. Appendix: Fax Troubleshooting Guide
IP-Fax Reception
5 Specified port number correct (if required)? Request the sender to check the port number.
7 Network bandwidth too narrow? Lower the start modem reception baud rate on
the receiving side.
IPFAX SW06
182
IP-Fax Troubleshooting
IP address/host name of specified VoIP Request the remote fax to check the IP address/
5
Gateway correct on sender’s side? host name.
183
4. Appendix: Fax Troubleshooting Guide
10 Network bandwidth too narrow? Lower the start modem reception baud rate on
the receiving side.
IPFAX SW06
184
5. Appendix: Fax Service Program
System Switch
101 Change the bit switches for system settings for the fax option
001 – 032 00 – 1F
( "p.191 "Bit Switches"") 5
Ifax Switch
102 Change the bit switches for internet fax settings for the fax
001 – 016 00 – 0F option
( "p.191 "Bit Switches"")
Printer Switch
103 Change the bit switches for printer settings for the fax option
001 – 016 00 – 0F
( "p.191 "Bit Switches"")
Communication Switch
104 Change the bit switches for communication settings for the
001 – 032 00 – 1F fax option
( "p.191 "Bit Switches"")
G3-1 Switch
105 Change the bit switches for the protocol settings of the
001 – 016 00 – 0F standard G3 board
( "p.191 "Bit Switches"")
IP fax Switch
185
5. Appendix: Fax Service Program
SP2-XXX (RAM)
RAM Read/Write
101
001 - Change RAM data for the fax board directly.
Memory Dump
102
001 G3-1 Memory Dump Print out RAM data for the fax board.
5
SP3-XXX (Machine Set)
Service Station
101
001 Fax Number Enter the fax number of the service station.
Serial Number
102
000 - Enter the fax unit’s serial number.
PSTN-1
Select the line type setting for the G3-1 line. If the
001 Select Line machine is installed on a PABX line, select “PABX”,
“PABX(GND)” or “PABX(FLASH)”.
103
PSTN Access Enter the PSTN access number for the
002
Number G3-1 line.
186
System Service Mode
IPFAX Protocol
007 Select "H323" or "SIP".
Priority
201
FAX SW
5
001 – 032 00 – 1F -
101 002 – 007 FCU ROM Version Displays the FCU ROM version.
102 002 – 065 Error Codes Displays the latest 64 fax error codes.
103 002 – 004 G3-1 ROM Version Displays the G3-1 modem version.
187
5. Appendix: Fax Service Program
Factory Setting
104 Resets the bit switches and user parameters, user data in the SRAM
001
and files in the SAF memory.
106 Initializes only the security bit switches. If you select automatic output/
001 display for the user parameter switches, the security settings are
5 initialized.
SP6-XXX (Report)
188
System Service Mode
105
001 -
• Do not use this function, unless the customer is
having trouble printing confidential messages
or recovering files stored using the memory
lock feature.
002 Printer
004 Decompression
005 Scanner
006 JOB/SAF
107 These log print out functions are for designer use
007 Reconstruction
only.
008 JBIG
010 G3CCU
012 CCU
189
5. Appendix: Fax Service Program
SP7-XXX (Tests)
190
Bit Switches
Bit Switches
• Do not adjust a bit switch or use a setting that is described as “Not used”, as this may cause the
machine to malfunction or to operate in a manner that is not accepted by local regulations. Such
bits are for use only in other areas, such as Japan.
• Default settings for bit switches are not listed in this manual. Refer to the System Parameter List
printed by the machine.
System Switches
191
5. Appendix: Fax Service Program
e.g. 0000 (1) // 32 (2) V34 (3) // 288 (4) // 264 (5) // L0100 (6) 03 (7) 04 (8)
(1): EQM value (Line quality data). A larger number means more errors.
(2): Symbol rate (V.34 only)
(3): Final modem type used
(4): Starting data rate (for example, 288 means 28.8 kbps)
(5): Final data rate
(6): Rx level (refer to the note after this table for how to read the rx level)
(7): Total number of error lines that occurred during non-ECM reception.
(8): Total number of burst error lines that occurred during non-ECM reception.
5 • The seventh and eighth numbers are fixed at “00” for transmission records and ECM
reception records.
Rx level calculation
Example: 0000 // 32 V34 // 288/264 // L 01 00 03 04
The four-digit hexadecimal value (N) after “L” indicates the rx level.
The high byte is given first, followed by the low byte. Divide the decimal value of N by -16 to
get the rx level.
In the above example, the decimal value of N (= 0100 [H]) is 256.
So, the actual rx level is 256/-16 = -16 dB
Line error mark print When "1" is selected, a line error mark is printed on the
4
0: OFF, 1: ON (print) printout if a line error occurs during reception.
G3/G4 communication This is a fault-finding aid. The LCD shows the key
parameter display parameters (see below). This is normally disabled
5 because it cancels the CSI display for the user.
0: Disabled
1: Enabled Be sure to reset this bit to 0 after testing.
Protocol dump list output after This is only used for communication troubleshooting. It
each communication shows the content of the transmitted facsimile protocol
6 signals. Always reset this bit to 0 after finishing testing.
0: Off
If system switch 09 bit 6 is at “1”, the list is only printed if
1: On there was an error during the communication.
192
Bit Switches
System Switch 01 - Not used (Do not change the factory settings.)
No FUNCTION COMMENTS
Forced reset after transmission stall With this setting on, the machine resets itself
2 0: Off automatically if a transmission stalls and fails to complete
1: On the job.
5
3 Not used Do not change these settings.
No FUNCTION COMMENTS
193
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
Printing dedicated tx parameters 1: Each Quick/Speed dial number on the list is printed
on Quick/Speed Dial Lists with the dedicated tx parameters (10 bytes each).
3 The first 10 bytes of data are the programmed dedicated
0: Disabled
5 1: Enabled
tx parameters; 34 bytes of data are printed (the other 24
bytes have no use for service technicians).
System Switch 05 - Not used (Do not change the factory settings.)
System Switch 06 - Not used (Do not change the factory settings.)
System Switch 07 - Not used (Do not change the factory settings.)
System Switch 08 - Not used (Do not change the factory settings.)
No FUNCTION COMMENTS
194
Bit Switches
No FUNCTION COMMENTS
4 Dialing on the ten-key pad 0: Prevents dialing from the ten-key pad while the
when the external telephone is external telephone is off-hook. Use this setting when the
off-hook external telephone is not by the machine, or if a wireless
0: Disabled 1: Enabled telephone is connected as an external telephone.
1: The user can dial on the machine’s ten-key pad when
the handset is off-hook.
195
5. Appendix: Fax Service Program
System Switch 0B - Not used (Do not change the factory settings.)
System Switch 0C - Not used (Do not change the factory settings.)
System Switch 0D - Not used (Do not change the factory settings.)
No FUNCTION COMMENTS
2 Not used This machine does not have the capture function.
No FUNCTION COMMENTS
196
Bit Switches
05: Belgium 16: Australia This country/area code determines the factory
settings of bit switches and RAM addresses.
06: Denmark 17: New Zealand However, it has no effect on the NCU parameter
settings and communication parameter RAM
0-7 07: Finland 18: Singapore
addresses. 5
08: Ireland 19: Malaysia Cross reference
No FUNCTION COMMENTS
197
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
5 destinations
No FUNCTION COMMENTS
TTI: 08 to 92 (BCD) mm
Input even numbers only.
This setting determines the print start position for the TTI
TTI printing position in the main from the left edge of the paper. If the TTI is moved too far
0-7
scan direction to the right, it may overwrite the file number which is on
the top right of the page. On an A4 page, if the TTI is
moved over by more than 50 mm, it may overwrite the
page number.
No FUNCTION COMMENTS
198
Bit Switches
30 min1
transmission, the machine goes to the Energy Saver
mode.
5
Bit 5: 1, Bit 4: 0
1 hour
Bit 5: 1, Bit 4: 1
24 hours
No FUNCTION COMMENTS
1: ON
No FUNCTION COMMENTS
199
5. Appendix: Fax Service Program
Scanner page-memory
expansion (On DRAM added) Expands the 4MB page-memory to 12MB, to improve
6 scanning possible range.
0: Not expanding
This SW does not work without DRAM added.
1: Expanding
No FUNCTION COMMENTS
RTI/CSI/CPS code display 0: RTI, CSI, CPS codes are displayed on the top line of the
0 0: Enable LCD panel during communication.
1: Disable 1: Codes are switched off (no display)
200
Bit Switches
No FUNCTION COMMENTS
RTI/CSI display priority This bit determines which identifier, RTI or CSI, is
2 displayed on the LCD while the machine is
0: RTI 1: CSI communicating in G3 non-standard mode.
201
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
Received fax print start timing 0: The machine prints each page immediately after the
(G3 reception) machine receives it.
5 3
0: After receiving each page 1: The machine prints the complete message after the
1: After receiving all pages machine receives all the pages in the memory.
I-Fax Switches
FUNCTION COMMENTS
202
Bit Switches
0 A4
1 B4
2 A3 0: Not selected
1: Selected
3 Reserved (B4)
This function can keep a transmitting operation from a
4 Reserved (A2) destination’s incapacity error for the size limitation.
5 Reserved
6 Reserved
0 200x100 Standard
1 200x200 Detail
0: Not selected
2 200x400 Fine 1: Selected
3 300 x 300 Reserve If more than one of these three bits is set to “1”, the
higher resolution has priority. For example, if both Bit 0
4 400 x 400 Super Fine and Bit 2 are set to “1” then the resolution is set for "Bit 2
200 x 400.
5 600 x 600 Reserve
6 Reserve
203
5. Appendix: Fax Service Program
mm/inch
No FUNCTION COMMENTS
This setting determines whether the header information is printed with text e-mails when they
are received.
0: Prints only text mail.
0 1: Prints mail header information attached to text mail.
When a text mail is received with this switch On (1), the “From” address and “Subject” address
are printed as header information.
When a mail with only binary data is received (a TIFF-F file, for example), this setting is ignored
and no header is printed.
204
Bit Switches
This setting determines whether only the first page or all pages of an e-mail attachment are
printed at the sending station when a transmission error occurs. This allows the customer to see
1 which documents have not reached their intended destinations if sent to the wrong e-mail
addresses, for example.
0: Prints 1st page only.
1: Prints all pages.
This setting determines the text string output for the Return Receipt that confirms the transmission
was received normally at the destination.
00: “Dispatched”
Sends from PC mail a request for a Return Receipt. Receives the Return Receipt with
“dispatched” in the 2nd part:
5
Disposition: Automatic-action/MDN-send automatically; dispatched
The “dispatched” string is included in the Subject string.
01: “Displayed”
2-3
Sends from PC mail a request for a Return Receipt. Receives the Return Receipt with
“displayed” in the 2nd part:
Disposition: Automatic-action/MDN-send automatically; displayed
The “displayed” string is included in the Subject string.
10: Reserved
11: Reserved
A mail requesting a Return Receipt sent from an IFAX with this switch set to “00” (for
“dispatched”) received by Microsoft Outlook 2000 may cause an error. If any setting other
than “displayed” (01) causes a problem, change the setting to “01” to enable normal sending
of the Return Receipt.
This setting adds or does not add the media accept feature to the answer mail to confirm a
reception.
4 0: Does not add the media accept feature to the answer mail
1: Adds the media accept feature to the answer mail.
Use this bit switch if a problem occurs when the machine receives an answer mail, which
contains the media accept feature field.
205
5. Appendix: Fax Service Program
7 0: 200 x 200
1: 400 x 400
The “1” setting requires installation of the Function Upgrade Card in order to have enough SAF
(Store and Forward) memory to receive images at 400 x 400 resolution.
I-fax Switch 03 - Not used (do not change the settings) [ SP No. 1-102-004]
5 No FUNCTION COMMENTS
This setting determines whether the RTI/CSI registered on this machine or the RTI/CSI of the
originator is used in the subject lines of transferred documents.
0: Puts the RTI/CSI of the originator in the Subject line. If this is used, either the RTI or CSI is
0 used. Only one of these can be received for use in the subject line.
1: Puts the RTI/CSI registered on this machine in the Subject line.
When this switch is used to transfer and deliver mail to a PC, the information in the Subject line
that indicates where the transmission originated can be used to determine automatically the
destination folder for each e-mail.
0: Standard subject
1: Mail post database subject
The standard subject is replaced by the mail post database subject in the following three cases:
1) When the service technician sets the service (software) switch.
1
2) When memory sending, delivery specified by F code or SMTP reception is done.
3) With relay broadcasting (1st stage without the Schmidt 4 function).
• This switch does not apply for condition 3) when the RX system is set up for memory
sending, delivery by F-code, sending with SMTP RX and when operators are using FOL
(to prevent problems when receiving transmissions).
206
Bit Switches
No FUNCTION COMMENTS
Determines whether the e-mail addresses of the destinations that receive transmissions
broadcasted using SMTP protocol are recorded in the Journal.
For example:
"1st destination + Total number of destinations: 9" in the Journal indicates a broadcast to 9
destinations.
0: Not recorded
1: Recorded 5
1 I-Fax Automatic Re-dial Setting Determines whether the I-fax automatically redials
0: OFF when an error occurs.
1: ON
I-fax Switch 06 - Not used (do not change the settings) [SP No. 1-102-007]
I-fax Switch 07 - Not used (do not change the settings) [SP No. 1-102-008]
No FUNCTION COMMENTS
This setting determines the amount of SAF (Store and Forward) memory. (SAF stores fax
messages to send later for transmission to more than one location, and also holds incoming
messages if they cannot be printed.) When the amount of SAF memory available falls below
0-7 this setting, mail can no longer be received; received mail is then stored on the mail server.
00-FF (0 to 1024 KB: HEX)
207
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
I-fax Switch 0A - Not used (do not change the settings) [SP No. 1-102-011]
I-fax Switch 0B - Not used (do not change the settings) [SP No. 1-102-012]
I-fax Switch 0C - Not used (do not change the settings) [SP No. 1-102-013]
5
I-fax Switch 0D [SP No. 1-102-014]
No FUNCTION COMMENTS
Bit SW(3,2)
(0,0): Not attached
(0,1): Setting forbidden
(0,1): Individual settings (Initial Setting)
(0,1): Attached at all times
208
Bit Switches
Bit SW(5,4)
(0,0): Not attached
(0,1): Setting forbidden
(0,1): Individual settings (Initial Setting)
(0,1): Attached at all times
I-fax Switch 0E - Not used (do not change the settings) [SP No. 1-102-015]
No FUNCTION COMMENTS
5
Delivery Method for SMTP RX Files
This setting determines whether files received with SMTP protocol are delivered or output
0 immediately.
0: Off. Files received via SMTP are output immediately without delivery.
1: On. Files received via SMTP are delivered immediately to their destinations.
This setting determines whether the signature is attached or not on files received with SMTP
1 protocol.
0: Off.
1: On.
Selects the encryption for SMTP RX files ON/OFF when the address encryption setting is
2 “Individual Setting”.
0: OFF.
1: ON.
209
5. Appendix: Fax Service Program
Printer Switches
No FUNCTION COMMENTS
Prints the date and time on This switch is only effective when user parameter 02 - bit
received fax messages 2 (printing the received date and time on received fax
2 messages) is enabled.
0: Disabled
1: The machine prints the received and printed date and
1: Enabled time at the bottom of each received page.
Printer Switch 01 - Not used (do not change the settings) [SP No. 1-103-002]
No FUNCTION COMMENTS
210
Bit Switches
No FUNCTION COMMENTS
211
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
Maximum reducible length when length reduction is enabled with switch 03-0 above.
5 <Maximum reducible length> = <Paper length> + (N x 5mm)
“N” is the decimal value of the binary setting of bits 0 to 4.
0 0 0 0 0 0 mm
0-4
0 0 0 0 1 5 mm
0 0 1 0 0 20 mm
1 1 1 1 1 155 mm
Length of the duplicated image on the next page, when page separation has taken place.
Bit 6: 0, Bit 5: 0 = 4 mm
5-6 Bit 6: 1, Bit 5: 0 = 10 mm
Bit 6: 0, Bit 5: 1 = 15 mm
Bit 6: 1, Bit 5: 1 = Not used
212
Bit Switches
No FUNCTION COMMENTS
No FUNCTION COMMENTS 5
0-3 Not used. Do not change the settings.
Printer Switch 08 - Not used (do not change the settings) [SP No. 1-103-009]
Printer Switch 09 - Not used (do not change the settings) [SP No. 1-103-010]
Printer Switch 0A - Not used (do not change the settings) [SP No. 1-103-011]
Printer Switch 0B - Not used (do not change the settings) [SP No. 1-103-012]
Printer Switch 0C - Not used (do not change the settings) [SP No. 1-103-013]
Printer Switch 0D - Not used (do not change the settings) [SP No. 1-103-014]
No FUNCTION COMMENTS
213
5. Appendix: Fax Service Program
Printing the sample image on reports “Same size” means the sample image is printed at
Bit 4: 0, Bit 3: 0 = The upper half only 100%, even if page separation occurs.
Bit 4: 0, Bit 3: 1 = 50% reduction in sub- User Parameter Switch 19 (13H) bit 4 must be set
3-4
scan only to “0” to enable this switch.
Bit 4: 1, Bit 3: 0 = Same size Refer to Detailed Section Descriptions for more on
Bit 4: 1, Bit 3: 1 = Not used this feature.
Equalizing the reduction ratio among 0: When page separation has taken place, all the
separated pages pages are reduced with the same reduction ratio.
7 (Page Separation) 1: Only the last page is reduced to fit the selected
0: Enabled paper size when page separation has taken
1: Disabled place. Other pages are printed without reduction.
No FUNCTION COMMENTS
214
Bit Switches
Smoothing feature
Bit 1: 0 Bit 0: 0 = Disabled (0, 0) (0, 1): Disable smoothing if the machine receives
0-1 Bit 1: 0 Bit 0: 1 = Disabled halftone images from other manufacturers fax machines
Bit 1: 1 Bit 0: 0 = Enabled frequently.
No FUNCTION COMMENTS
Bit 3: 1 Bit 2: 1 =
MH/MR/MMR/JBIG
215
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
00: OFF
The trigger selection for the G3 01: All CSI digits un-corresponded
2-3
misconnecting protection 10: The last 4 CSI digits un-corresponded
11: CSI and RTI absence
216
Bit Switches
No FUNCTION COMMENTS
Acceptable total error line ratio If the error line ratio for a page exceeds the acceptable
1
0: 5% 1: 10% ratio, RTN will be sent to the other end.
217
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
No FUNCTION COMMENTS
Remote switch setting for TEL mode Determines whether remote switching is ON/OFF on
0
0: OFF 1: ON receiving fax transmission, in TEL mode.
No FUNCTION COMMENTS
218
Bit Switches
No FUNCTION COMMENTS
No FUNCTION COMMENTS
Point of resumption of memory 0: The transmission begins from the page where
transmission upon redialing transmission failed the previous time.
0
0: From the error page 1: Transmission begins from the first page, using normal
1: From page 1 memory transmission. 5
1-7 Not used Do not change the settings.
No FUNCTION COMMENTS
No FUNCTION COMMENTS
219
5. Appendix: Fax Service Program
The available memory threshold, The machine refers to this setting before each fax
below which ringing detection reception. If the amount of remaining memory is below
0-7 this threshold, the machine cannot receive any fax
(and therefore reception into
memory) is disabled messages.
If this setting is kept at 0, the machine will detect ringing
signals and go into receive mode even if there is no
memory available. This will result in communication
failure.
06 to FF (Hex), unit = 2 s
Minimum interval between (e.g., 06(H) = 12 s)
0-7
automatic dialing attempts This value is the minimum time that the machine waits
before it dials the next destination.
No FUNCTION COMMENTS
No FUNCTION COMMENTS
220
Bit Switches
No FUNCTION COMMENTS
No FUNCTION COMMENTS
221
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
222
Bit Switches
No FUNCTION COMMENTS
No FUNCTION COMMENTS
G3-1 Switches
No FUNCTION COMMENTS
Monitor speaker during (0, 0): The monitor speaker is disabled all through the
communication (tx and rx) communication.
Bit 1: 0, Bit 0: 0 = Disabled (0, 1): The monitor speaker is on up to phase B in the T.
0-1 30 protocol.
Bit 1: 0, Bit 0: 1 = Up to Phase B
(1, 0): Used for testing. The monitor speaker is on all
Bit 1: 1, Bit 0: 0 = All the time
through the communication. Make sure that you reset
Bit 1: 1, Bit 0: 1 = Reserved these bits after testing.
223
5. Appendix: Fax Service Program
Private G3 FAX line enabled/ This function is used in the situation that one fax is
6 disabled switch connected to the other directly without switching
0: Disabled / 1:Enabled equipment.
No FUNCTION COMMENTS
5 0-3 Not used Do not change the settings.
1: The bytes in the DIS frame after the 4th byte will not be
DIS frame length limitation transmitted (set to 1 if there are communication problems
4
0: OFF 1: 4 bytes with PC-based faxes which cannot receive the extended
DIS frames).
Forbid CED/AMsam output Do not change this setting (Default: 0: Off), unless
6 0: Off communication problem is caused by a CED or ANSam
1: On (Forbid output) transmission.
No FUNCTION COMMENTS
Change this bit to 1 only when the other end can only
G3 protocol mode used communicate with machines that send T.30-standard
0 0: Standard and non-standard frames only.
1: Standard only 1: Disables NSF/NSS signals (these are used in non-
standard mode communication)
224
Bit Switches
No FUNCTION COMMENTS
DIS detection number 0: The machine will hang up if it receives the same DIS
(Echo countermeasure) frame twice.
0
0: 1 1: Before sending DCS, the machine will wait for the
1: 2 second DIS which is caused by echo on the line.
V.8 protocol
0: V.8/V.34 communications will not be possible.
5
Note:
2 0: Disabled Do not set to 0 unless the line condition is always bad
1: Enabled enough to slow down the data rate to 14.4 kbps or
lower.
225
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
226
Bit Switches
0 0 0 1 2.4k
0 0 1 0 4.8k
0 0 1 1 7.2k
0 1 0 0 9.6k
These bits set the initial starting modem rate for
0 1 0 1 12.0k transmission.
0 1 1 0 14.4k Use the dedicated transmission parameters if you need
to change this for specific receivers.
0-3 0 1 1 1 16.8k
If a modem rate 14.4 kbps or slower is selected, V.8
1 0 0 0 19.2k protocol should be disabled manually. 5
Cross reference
1 0 0 1 21.6k
V.8 protocol on/off - G3 switch 03, bit2
1 0 1 0 24.0k
1 0 1 1 26.4k
1 1 0 0 28.8k
1 1 0 1 31.2k
1 1 1 0 33.6k
No FUNCTION COMMENTS
227
5. Appendix: Fax Service Program
0 0 0 1 2.4k
0 0 1 0 4.8k
0 0 1 1 7.2k
0 1 0 0 9.6k
• These bits set the initial starting modem rate
0 1 0 1 12.0k for reception.
• Use a lower setting if high speeds pose
0 1 1 0 14.4k
problems during reception.
0-3 0 1 1 1 16.8k • If a modem rate 14.4 kbps or slower is
5 1 0 0 0 19.2k
selected, V.8 protocol should be disabled
manually.
1 0 0 1 21.6k Cross reference:
V.8 protocol on/off - G3 switch 03, bit2
1 0 1 0 24.0k
1 0 1 1 26.4k
1 1 0 0 28.8k
1 1 0 1 31.2k
1 1 1 0 33.6k
228
Bit Switches
0 0 0 1 V.27ter
No FUNCTION COMMENTS
229
5. Appendix: Fax Service Program
(rx mode: Internal) Also, try using the cable equalizer if one or more
of the following symptoms occurs.
Bit 3: 0, Bit 2: 0 = None
2-3 Communication error with error codes such as
Bit 3: 0, Bit 2: 1 = Low
0-20, 0-23, etc.
Bit 3: 1, Bit 2: 0 = Medium
Modem rate fallback occurs frequently.
Bit 3: 1, Bit 2: 1 = High
No FUNCTION COMMENTS
230
Bit Switches
(rx mode: Internal) Also, try using the cable equalizer if one or more
of the following symptoms occurs.
Bit 3: 0, Bit 2: 0 = None
2-3 Communication error with error codes such as
Bit 3: 0, Bit 2: 1 = Low
0-20, 0-23, etc.
Bit 3: 1, Bit 2: 0 = Medium
Modem rate fallback occurs frequently.
Bit 3: 1, Bit 2: 1 = High
No FUNCTION COMMENTS
231
5. Appendix: Fax Service Program
No FUNCTION COMMENTS
232
Bit Switches
00-0E(3000-3700ms: 3000+50xNms
Low order bit
3000 – 50 x Nms 0F (3000 ms) < N < 0F (3700 ms)
No FUNCTION COMMENTS
233
5. Appendix: Fax Service Program
IP Fax Switches
5 1
IP Fax Transport
Selects TCP or UDP protocol for IP-Fax
0: TCP, 1: UDP
234
Bit Switches
IP-Fax Switch 01
Select IP FAX Delay Level Raise the level by selecting a higher setting if too
many transmission errors are occurring on the
Bit3 Bit2 Bit1 Bit0 Setting
0 0 0 0 Level 0
network.
If TCP/UDP is enabled on the network, raise this
5
setting on the T.30 machine. Increasing the delay
0-3 0 0 0 1 Level 1 time allows the recovery of more lost packets.
0 0 1 0 Level 2 If only UDP is enabled, increase the number of
redundant packets.
0 0 1 1 Level 3
Level 1 to 2: 3 Redundant packets
Level 3: 4 Redundant packets
235
5. Appendix: Fax Service Program
SIP transport setting This bit switch sets the transport that has priority for
receiving IP Fax data.
2 0: TCP
This function is activated only when the sender has
5 1: UDP both TCP and UDP.
Message reception selection from non- 0: This answers the INVITE message from the SIP
registered SIP server server not registered for the machine.
4 1: This does not receive the INVITE message from
0: Answer
the SIP server not registered for the machine and
1: Not answer send a refusal message.
236
Bit Switches
5
CTC transmission selection
0: PPRx1
decided by error frame numbers. 5
When "1" is selected, the transmission condition is
1: PPRx4 based on the ITU-T method.
237
5. Appendix: Fax Service Program
0 0 0 1 2400 bps
0 0 1 1 4800 bps
0 0 1 1 7200 bps
0 1 0 0 9600 bps
0 1 0 1 12.0 Kbps
5 0 1 1 1 Not Used
1 0 0 0 Not Used
1 0 0 1 Not Used
1 0 1 0 Not Used
1 0 1 1 Not Used
1 1 0 0 Not Used
1 1 0 1 Not Used
1 1 1 0 Not Used
238
Bit Switches
0 0 0 1 2400 bps
0 0 1 0 4800 bps
0 0 1 1 7200 bps
0 1 0 0 9600 bps
0 1 0 1 12.0 Kbps
0-3
0 1 1 0 14.4 Kbps 5
0 1 1 1 Not Used
1 0 0 0 Not Used
1 0 0 1 Not Used
1 0 1 0 Not Used
1 0 1 1 Not Used
1 1 0 0 Not Used
1 1 0 1 Not Used
1 1 1 0 Not Used
239
5. Appendix: Fax Service Program
0 0 0 1 V27ter
0 0 1 0 V27ter, V29
4-7
V27ter, V29, V33
0 0 1 1
(invalid)
0 1 0 1 Not Used
TSI information
0 Adds or does not add TSI information to NSS(S).
0: Not added, 1: Added
Number of times for training Selects the number of times training is done at the
4
0: 1 time, 1: 2 times same bit rate.
240
Bit Switches
T1 timer adjustment
Adjusts the T1 timer.
The default is "00" (35 seconds).
0-1 Bit 1: 0, Bit 0: 0 = 35 sec -
Bit 1: 0, Bit 0: 1 = 40 sec
Bit 1: 1, Bit 0: 0 = 50 sec
Bit 1: 1, Bit 0: 1 = 60 sec
T4 timer adjustment
5
Adjust the T4 timer.
The default is "00" (3 seconds).
2-3 Bit 3: 0, Bit 2: 0 = 3 sec -
Bit 3: 0, Bit 2: 1 = 3.5 sec
Bit 3: 1, Bit 2: 0 = 4 sec
Bit 3: 1, Bit 2: 1 = 5 sec
T0 timer adjustment Adjusts the fail safe timer. This timer sets the interval
Bit 5: 0, Bit 4: 0 = 75 sec between "setup" data transmission and T.38 phase
decision. If your destination return is late on the
4-5 Bit 5: 0, Bit 4: 1 = 120 sec network or G3 fax return is late, adjust the longer
Bit 5: 1, Bit 4: 0 = 180 sec interval timer.
Bit 5: 1, Bit 4: 1 = 240 sec The default is "00" (75 seconds).
241
5. Appendix: Fax Service Program
1: Automatic setting
Record-route using
“Enabled” is for Record-route acceptable SIP
2 1: Enabled
server
2: Disabled
5 Bit 3 Bit 4
Set this function more than “1 sec” when SIP
3-4 0 0 No delay connection is done via HiPath8000/4000
1 0 1 sec (Siemen Co.)
0 1 2 sec
1 1 3 sec
242
NCU Parameters
NCU Parameters
• The following tables give the RAM addresses and the parameter calculation units that the machine
uses for ringing signal detection and automatic dialing. The factory settings for each country are
also given. Most of these must be changed by RAM read/write (SP2-101), but some can be
changed using NCU Parameter programming (SP2-103); if SP2-103 can be used, this will be
indicated in the Remarks column. The RAM is programmed in hex code unless (BCD) is included in
the Unit column.
243
5. Appendix: Fax Service Program
Address Function
Use the Hex value to program the country/area code directly into this address, or use
the decimal value to program it using SP2-103-001
France 00 00 USA 17 11
Germany 01 01 Asia 18 12
UK 02 02 Japan 19 13
Hong Kong 20 14
5
Italy 03 03 South 21 15
Africa
Austria 04 04 Australia 22 16
Belgium 05 05 New 23 17
680500
Zealand
Denmark 06 06 Singapore 24 18
Finland 07 07 Malaysia 25 19
Ireland 08 08 China 26 1A
Norway 09 09 Taiwan 27 1B
Sweden 10 0A Korea 28 1C
Switzerland 11 0B Brazil 29 1D
Turkey 32 20
Portugal 12 0C Greece 33 21
Holland 13 0D Hungary 34 22
Spain 14 0E Czech 35 23
Israel 15 0F Poland 36 24
244
NCU Parameters
245
5. Appendix: Fax Service Program
5 680518
PABX dial tone frequency upper limit
Hz (BCD) FF(H), tone detection is
disabled.
(low byte)
68051C PABX dial tone reset time (LOW) If 68051B contains FF, the
machine pauses for the
68051D PABX dial tone reset time (HIGH)
pause time (680520 /
68051E PABX dial tone continuous tone time 20 ms 680521).
246
NCU Parameters
680529
PABX busy tone frequency lower limit
Hz (BCD) FF(H), tone detection is
disabled. 5
(low byte)
247
5. Appendix: Fax Service Program
Busy tone signal state time tolerance for all ranges, and number of cycles required for
detection (a setting of 4 cycles means that ON-OFF-ON or OFF-ON-OFF must be
detected twice).
Tolerance (±)
248
NCU Parameters
680543 Country dial tone detection time If 680543 contains FF, the
machine pauses for the
680544 Country dial tone reset time (LOW) 20 ms
pause time (680548 /
680549).
5
680545 Country dial tone reset time (HIGH)
See Note 3.
68054B Break time for pulse dialing 1 ms SP2-103-013 (parameter
12).
See Note 3.
68054C Make time for pulse dialing 1 ms SP2-103-014 (parameter
13).
249
5. Appendix: Fax Service Program
SP2-103-018 (parameter
680550 DTMF tone on time
17).
1 ms
SP2-103-019 (parameter
680551 DTMF tone off time
18).
SP2-103-020 (parameter
Tone attenuation level of DTMF signals -N x 0.5 –3.5 19).
5 680552
while dialing dBm
See Note 5.
SP2-103-021 (parameter
20).
Tone attenuation value difference The setting must be less than
680553 between high frequency tone and low -dBm x 0.5 –5dBm, and should not
frequency tone in DTMF signals exceed the setting at
680552h above.
See Note 5.
250
NCU Parameters
68055F
To Not used - Do not change the settings.
680564
680567
to Not used - Do not change the settings.
680571
251
5. Appendix: Fax Service Program
SP2-103-007 (parameter
680576 Number of rings until a call is detected 1 06).
See Note 4.
Minimum required length of the first
680577 20 ms SP2-103-008 (parameter
ring
07).
68057B
to Not used - Do not change the settings.
680580
252
NCU Parameters
680583
To Not used - Do not change the settings. 5
6805A0
20 ms ± 20
6805A5 CED detection time Factory setting: 200 ms
ms
253
5. Appendix: Fax Service Program
SP2-103-002 (parameter
6805B4 PSTN: Tx level from the modem -N – 3 dBm
01).
6805B8 PABX: 1100 Hz tone transmission level - N 6805B7 - 0.5N 6805B8 (dB)
6805B9 PABX: 2100 Hz tone transmission level - N 6805B7 - 0.5N 6805B9 (dB)
254
NCU Parameters
6805BE to
Not used - Do not change the settings.
6805C6
6805C8 to
Not used - Do not change the settings.
6805D9
0 RT=0 (Low)
Bit 2
Bit 2 sets the level of 1 RT=1 (High)
the call signal, Bit 3
6805E4 0 RZ=0 (High) -
sets the call signal
impedance Bit 3 RZ=1
1
(Composite)
0 Auto
Bit 0 sets the ring Bit 0
detection method, Bit 1 Fixed
1 sets the ring If any setting is changed,
6805E5 detection method 0 Use RDTP select a setting that is higher
when fixed. Bit 1 than the default setting.
1 Use RDTN
NOTES
255
5. Appendix: Fax Service Program
256
Dedicated Transmission Parameters
Programming Procedure
Parameters
Fax Parameters
The initial settings of the following fax parameters are all FF(H) - all the parameters are disabled.
Switch 00
257
5. Appendix: Fax Service Program
Switch 01
No FUNCTION COMMENTS
258
Dedicated Transmission Parameters
5
• Do not use settings other than
listed on the left.
If the setting is "Disabled", the bit
switch setting is used.
Switch 02
No FUNCTION COMMENTS
259
5. Appendix: Fax Service Program
0 0 0 0 Not used
1 1 1 0 33600
1 1 1 1 Disabled
Switch 03
No FUNCTION COMMENTS
260
Dedicated Transmission Parameters
6-7
Bit 7: 0, Bit 6: 0 = Off
Bit 7: 0, Bit 6: 1 = On
5
• V.8/V.34 protocol and JBIG compression are
Bit 7: 1, Bit 6: 0 = Not used
automatically disabled if ECM is disabled.
Bit 7: 1, Bit 6: 1 = Disabled
• If the setting is "Disabled", the bit switch setting is
used.
E-mail Parameters
The initial settings of the following e-mail parameters are all "0" (all parameters disabled).
Switch 00
No FUNCTION COMMENTS
261
5. Appendix: Fax Service Program
Switch 01
No FUNCTION COMMENTS
262
Dedicated Transmission Parameters
Switch 02
5
No FUNCTION COMMENTS
263
5. Appendix: Fax Service Program
Switch 04
No FUNCTION COMMENTS
If the other ends have the addresses, which have the full
mode function flag ("0"), this machine determines them as
5 Full mode address selection
full mode standard machines.
0: Full mode address
0 • This machine attaches the "demand of reception
1: No full mode (simple confirmation" to a message when transmitting.
mode)
• This machine updates the reception capability to the
address book when receiving.
Switch 05
No FUNCTION COMMENTS
264 EN
Gruppo di Alimentazione Carta
PB 1040
Codice Macchina: D661
28 Dicembre 2011
SOMMARIO
1. Sostituzione e regolazione
Gruppo cassetti carta ........................................................................................................................................3
Gruppo cassetti carta ....................................................................................................................................3
Rullo di alimentazione e Feltrino di frizione.................................................................................................3
Sensori.................................................................................................................................................................5
Azionamento.......................................................................................................................................................6
Ventola di raffreddamento............................................................................................................................6
Staffa di azionamento e Frizione di alimentazione carta...........................................................................6
Motore di alimentazione carta.....................................................................................................................7
Scheda principale cassetto............................................................................................................................7
1
2
1. Sostituzione e regolazione
3
1. Sostituzione e regolazione
4
Sensori
Sensori
1. Rimuovere il gruppo cassetti carta dalla copiatrice ( P.3 "Gruppo cassetti carta ").
5
1. Sostituzione e regolazione
Azionamento
Ventola di raffreddamento
1. Rimuovere il gruppo cassetti carta dalla copiatrice ( P.3 "Gruppo cassetti carta ").
6
Azionamento
7
MEMO
8 IT
1 2 3 4 5 6
D1171470
D1271463 31 CN155 CN155 CN1 JCN1 CN3 CN2
1
1
LED Board OP-R CT 3pin
CN CN CN CN151 CT 4pin CT 4pin CT 4pin
(PCB3) (PCB2)
4
CN CN CN USB 4pin CN1
Operation D1275220 1 2/2 D1275239 14
CT 2pin
Panel
D1171483
D1171489
OP-L
(PCB1) CN156
FFC 28pin
Operation D1171464 32
CN CN Panel CN150 PEACE D1275240 15 T1 Main SW
B miniMiⅡ
MiⅡ 6pin
PSU PS-187(t=0.8)
13pin
(PCB5)
13
1 13
LCDC CN CN111 ICIB T2
(PCB4)
CN CN152 200V Only
JAE 60pin
1
Operation PS-187(t=0.8)
Panel CN143
CN CN287 CN280 CN280 T3
CT 4pin
Molex 4.2mm 2pin Molex 6.5mm 4pin PS-187(t=0.8)
CN147 Choke Coil
N6074550 T4
CT 2pin
JCN101 CN1 CN102 CN402 PS-187(t=0.8)
ARDF miniCT 16pin miniCT 16pin CN101 IC CARD(DLTOOL I/F)
Platen Coversensor
FFC 45pin
(S7) SCANNER D1275205 36
CN283 CN CN
FFC D1275237 13 Molex 7mm
CN CN401 Option Tray Heater
SCANNER CN107 CN107 CN284 CN284 Option
UNIT FFC 40pin SCANNER D1275200 33 FFC 40pin
8pin
C miniCT 8pin miniCT
TAB1 T1
CN106 CN106 CN285 CN285
LED Unit (L1) PS-250(t=0.8)
Molex 3.5mm 8pin Molex 3.5mm 8pin
CN2 CN1 CN403 TAB2 T2 Power Supply Cord
miniCT 4pin miniCT 4pin PS-250(t=0.8)
Scanner Motor M5 Black:L White:N INLET
SCANNER D1275202 34 CN282 CN282
NA:Molex 6.5mm 2pin D1275241 16
EU:JST 5mm 2pin
D1275220 1 1/2
E CN122
CT
CN
3pin
M2 Exhaust Fan
PS-187
CN138 CN138 CN1 M3 Duplex Motor
Mini CT 4pin CT 6pin
D1275226 7
PCU D1275235 12
CN750
DIMM Socket
CN751
CN709 USB-HOST
By-pass PE Sensor
CN1 CN5 JCN5 CN5 CN130 CN130
(S3)
MiⅡ 2pin MiⅡ 2pin MiⅡ 2pin MiⅡ 3pin CN710 HDD Option
CN703 CN600
FAX UNIT
For SP Model
Option
J CN CT CN miniCT CN FFC
CN B to B CN Other
1 2 3 4 5 6 7 8 9 10
B B
16P
1 Reverse Switching Solenoid
2 Reverse Switching Solenoid_Feed
3 +24V
D6065212 4 +24V D6065211
5 DFConnection Detection
6 Platen Cover Sensor 2
16 10P
Main Machine CN CN 7 Original Set Sensor
Reverse Switching Solenoid 1 1
CN JCN CN SOL1 ARDF Pick-up Solenoid
1 8 +5VE (PONSENS)
+24V 2
D 9 GND D
Reverse Switching Solenoid_Feed 3
10 GND
+24V 4
11 Registration Sensor 1 3
GND 5 SOL2
12 +5V (Scanner)
Platen Cover Sensor 6
CN4
10 1
CN JCN CN ARDF Reverse Solenoid
13 Encoder_A
+5V (Scanner) 7
14 DCM motor (-)
GND 8
15 Encoder_B
Original Set Sensor 9
16 DCM motor (+) 3
+5VE (PONSENS) 10
1
CN S1 ADF Cover Sensor
3
E
1
CN S2 Original Set Sensor E
3P
D6065210
DGND 1 1 3
Registration Sensor 2 CN3
3 1
CN301 S3 ARDF Registration Sensor
+5V (Scanner) 3
F F
G G
1 2 3 4 5 6 7 8 9 10
D127/D128 Harness Pin Assign
Harness No Part No FROM J-CN CN Pin Signal Direction Pin CN J-CN TO Harness No Part No FROM J-CN CN Pin Signal Direction Pin CN J-CN TO
1 D127 BICU - CN114 1 +24VL Power T1 2 - Interlock 5 D127 BICU - CN104 1 PFU_RXD ← 14 CN1 - PFU
5220 CN114 2 +24VS ← T2 2 - Dual Type 5224 CN104 2 PFU_TXD → 13 JCN
BICU - CN123 1 N.C. - - Total Counter 3 GND G 12
CN123 2 N.C. - - 4 +5V Power 11
3 N.C. - 6 CN2 JCN T Sensor 5 GND G 10
4 GND G 5 2 6 GND G 9
5 FB_TSNS ← 4 7 GND G 8
6 +5V Power 3 8 +24V Power 7
7 PCU_SET ← 2 9 +24V Power 6
8 GND G 1 10 +24V Power 5
9 FB_PSNS ← 4 CN3 JCN3 【24】D0675214 - N.C. - 4
10 PSNS_LED → 3 CN2 - N.C. - 3
11 GND G 2 - N.C. - 2
12 +5V Power 1 - N.C. - 1
BICU - CN129 1 GND G 2 CN4 JCN4 【37】D1275218 6 D127 BICU - CN141 1 TBMT_ON_N → 2 CN1 - Toner Bottle
CN129 2 F1_PE ← 1 CN4 5225 CN141 2 N.C. - - Motor
BICU - CN155 1 REON_DC_N_ → 4 CN1 JCN1 【14】D1275239 3 +24VS Power 1
CN155 2 +5VE PO 3 CN3 7 D127 BICU - CN138 1 DUMT_BN → 6 CN1 - Duplex
3 ACSWON_N_ ← 2 5226 CN138 - NC - 5 Motor
4 GND G 1 2 DUMT_B → 4
2 D127 BICU - CN137 1 +24VS Power 2 CN1 JCN1 Fusing Solenoid 3 DUMT_AN → 3
5221 CN137 2 FU_SOL_N → 1 - NC - 2
3 +24VS Power 2 CN2 JCN2 Bypass Feed CL 4 DUMT_A → 1
4 MU_CL → 1 8 D127 【3】 - CN1 1 GND G 3 CN2 - Paper Exit
5 +24VS Power 2 CN3 JCN3 Paper Feed CL 5228 D1275222 2 EXIT_SNS_N ← 2 Sensor
6 F1_FDCL → 1 JCN1 3 +5V Power 1
BICU - CN139 1 +24VS Power 2 CN4 JCN4 Paper Regist CL 9 D127 【3】 - CN1 1 GND G 3 CN2 - Junction
CN139 2 REG_CL → 1 5251 D1275222 2 DSIDE_SNS_N ← 2 Sensor
BICU - CN130 1 GND G 2 CN5 JCN5 【26】D1275219 JCN3 3 +5V Power 1
CN130 2 N.C. - - CN5 10 D127 BICU - CN125 1 N.C. - - CN1 - HVPP
3 MU_PE ← 1 5230 CN125 2 N.C. - - CN1
3 D127 BICU - CN136 1 +3.3V Power 2 CN2 JCN2 Fusing Thermistor 3 FB_VTP ← 10
5222 CN136 2 FB_HEAT ← 1 4 HVP_SC_T_N ← 9
BICU - CN128 1 GND G 3 CN1 JCN1 【8】D1275228 5 HVP_SC_B_N ← 8
CN128 2 EXIT_SNS_N ← 2 CN1 6 HVP_SC_C_N ← 7
3 +5V Power 1 7 PWM_TM → 6
4 GND G 3 CN3 JCN3 【9】D1275251 8 PWM_TP → 5
5 DSIDE_SNS_N ← 2 CN2 9 PWM_B → 4
6 +5V Power 1 10 PWM_C → 3
4 D127 BICU - CN116 1 LDD2_N → 16 CN2 - LDB 11 GND G 2
5223 CN116 2 LDD2 → 15 CN 12 +24VS Power 1
3 +5VS Power 14 11 D127 BICU - CN133 1 N.C. - - CN4 - Right Door
4 +5VS Power 13 5216 CN133 2 ELEFAN_LOCK ← 2 Detect
5 LDD1_N → 12 3 GND G 1 Sensor
6 LDD1 → 11 12 D127 HVP - T1 Development ← T4 - PCU
5235 T2 B
7 DETP_N ← 10 HVP - T2 Charger ← T5 - PCU
T1 C
8 VLDERR ← 9 HVP - T3 Transfer ← T6 - PCU
T3 T
9 LDERR_N ← 8
10 LDOFF → 7
11 APCEN1_N → 6
12 GND G 5
13 LDLVL1 → 4
14 GND G 3
15 LDLVL2 → 2
16 APCEN2_N → 1
BICU - CN118 1 +24V Power 5 CN1 JCN1 【30】D1275270
CN118 2 GND G 4 CN2
3 PMON_N → 3
4 PMRDY_N ← 2
5 PMCLK → 1
Harness No Part No FROM J-CN CN Pin Signal Direction Pin CN J-CN TO Harness No Part No FROM J-CN CN Pin Signal Direction Pin CN J-CN TO
13 D127 BICU - CN107 1 N.C. - 8 CN284 - PSU 32 D127 BICU - - 1 GND G 13 CN2 JCN2 Operation
5237 CN107 2 ZEROX ← 7 CN284 1486 CN152 2 GND G 12 Panel
3 FUHT_ON → 6 3 POKLVDS → 11
4 RY_ON_N → 5 4 LDET_IN_N_OPU ← 10
5 PONENG_N_PSU → 4 5 ENG_ENABLE_N_OP → 9
6 GND G 3 6 PONENG_N_OPU → 8
7 +24V_ON Power 2 7 PW_SW_N ← 7
8 +24VSRLY Power 1 8 POKUSB → 6
BICU - CN106 1 +24V Power 1 CN285 - PSU 9 OPE_CTLERR_N_OP → 5
CN106 2 +24V Power 2 CN285 10 +5VE_LPS Power 4
3 GND G 3 11 +5VE_LPS Power 3
4 GND G 4 12 +5VE_LPS Power 2
5 GND G 5 13 +24V Power 1
6 +5V Power 6 33 D127 BICU - - 1 GND G 40 - - Scanner
7 +5VE Power 7 5200 CN401 2 GND G 39 Unit
8 +5VE Power 8 3 +24V Power 38
14 D127 【1】D1275220 - CN3 1 REON_DC_N_ → 2 CN1 - SDSW 4 +24V Power 37
5239 JCN1 2 +5VE PO 1 (Sub) 5 +5V_SCN Power 36
3 ACSWON_N_ ← 3 CN2 - SDSW 6 +5V_SCN Power 35
- N.C. - 2 (Sub) 7 GND G 34
4 GND G 1 8 VIDEO_R ← 33
15 D127 PSU - CN280 1 AC-L Power T1 - SDSW 9 GND G 32
5240 CN280 2 AC-N Power T2 - (Main) 10 VIDEO_G ← 31
3 AC-L-ON Power T3 - 11 GND G 30
4 AC-N-ON Power T4 - 12 VIDEO_B ← 29
16 D127 PSU - - T1 L Power INLET-L - Power Supply Cord 13
5241 Tab1 GND G 28
31
Symbol Index No. Name P-to-P
Motors
30 M1 26 Main I-1
M2 32 Exhaus t Fan E-5
M3 33 Duplex E-5
M4 21 Polygon Mirror D-1
29
M5 7 Scanner C-1
M6 29 Toner Bottle Motor E-5
M7 44 CTL Fan G-5
28 44 35
27 23 Clutches
26 24 CL1 27 Paper Feed H-1
25 CL2 30 Bypas s Feed H-1
CL3 28 Regis tration H-1
38
37 39 Others
36 TH1 43 Therm is tor D-5
40 SOL1 31 Fus ing Solenoid H-1
34 Therm o Switch
41 TS D-5
D127/D128
Connector
CN104 CN104 CN200 CN200 CN100 CN100
CN210
D6615300 CN102 CN102 CN220 M1 Paper Feed Motor
1
3 D6615320
2 D6615310
CN105 CN105 CN250 Paper Feed Sensor (S1)
E
D661 Harness Pin Assign
Harness Part No FROM Signal TO
No CN Unit/CN Pin No Direction CN Unit/CN Pin No
1 D6615300 CN100 Main PCB 10 TXD2→ CN200 D127/D128 1
CN100 9 ←RXD2 CN104 2
8 S_GND 3
7 +5V 4
6 P_GND 5
5 6
4 7
3 +24V 8
2 9
1 10
2 D6615310 CN101 Main PCB 1 ←LP_RXD3 CN201 Lower Papar Tray 14
CN101 2 LP_TXD3→ Unit 13
3 S_GND CN100 12
4 +5V 11
5 P_GND 10
6 9
7 8
8 +24V 7
9 6
10 5
3 D6615320 CN102 Main PCB 1 PFM_A CN220 Paper Feed Motor 5
CN102 2 PFM_+24V 4
3 PFM_AB 3
4 PFM_B 2
6 PFM_BB 1
4 D6615330 CN103 Main PCB 1 +24V CN230 Paper Feed Clutch 2
CN103 2 FEED CL 1
CN104 Main PCB 1 +24V Fan Motor
CN104 2 N.C.
3 FAN_M
5 D6615340 CN105 Main PCB 1 S_GND CN250 Paper Feed Sensor 3
CN105 2 PF_SIGNAL 2
3 +5V 1
4 S_GND CN251 Paper End Sensor 3
5 PE_SIGNAL 2
6 +5V 1
7 S_GND CN252 Door Switch 2
8 DS_SIGNAL 1
PSU 1 HEATER(L) Anticondensation 1
6 D6615350 CN1 CN283 2 HEATER(N) CN2 Heater (Option) 2
1 Symbol Index No. Name P-to-P
7 PFU (Option)
PCB1 1 Tray Main Board CDB-3
2
M1 2 Paper Feed Motor B-4
M2 7 FAN Motor C-4
CL1 3 Paper Feed Clutch B-4
3
S1 5 Paper Feed Sensor D-4
S2 6 Paper End Sensor D-4
SW1 4 Door Switch D-4
5
6