Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Dopo il controllo della parte finale HF driver, seguendo la parte di alimentazione DC dove
proviene il maggior assorbimento,
sono arrivato alla pista che porta al Q6 uno stabilizzatore di tensione 8V.
In seguito il Q7 2SC880 sulla sua base verso massa dorrei trovare circa 1.2V tensione di
soglia dei due diodi in serie.
Bingo, non c'è collegamento verso massa attraverso i diodi, non si trovano elettricamente i
diodi.
La pista è interrotta tra il transistor e il primo diodo. La pista per raggione di costruzione
passa sotto una bobina L8.
La bobina L8 è incollata alla piastra con silicone che con il tempo oppure un colpo ha
distaccato la pista interompendo il circuito.
La bobina L8 è incollata alla piastra con silicone che con il tempo oppure un colpo oppure
vibrazioni ha distaccato la pista
interrompendo il circuito. Per vedere il circuito interrotto bisogna dissaldare la bobina, se
no, non si vede il circuito interrotto.
Sicuramente la misura ohmica garantisce che il circuito è interrotto.
Riparare il difetto
Dissaldare la bobina L8 trovare il punto di rottura, risaldare la bobina.
Altre informazioni.
La piastra Finale HF deve essere totalmente smontata, i finali e i transistor di driver dal
raffreddamento,
quindi la pasta siliconica deve essere rimossa pulita e rimessa in abbondanza e
eterogenea.
Ultima cosa, e consiglio sostituire tutti i condensatori al tantalio che dopo anni di esistenza,
sono anche loro oggetto di problemi.
Buona riparazione e spero che le ore di lavoro da me fatte posso servire a qualcuno.
Migliori 73 da HB9TQF
************************************************************
Defect search
Since the absorption power breaks the main fuse, the fuse breaks in transmission,
the problem lies in the HF power plate.
After checking the final part HF driver, following the part of the DC power supply where the
greatest absorption comes
I arrived at the track that brings an 8V voltage stabilizer to the Q6 7808.
Then the Q7 2SC880 on its base to ground I should find about 1.2V threshold voltage of
the two diodes in series
Bingo, there is no connection to ground through the diodes, the diodes are not found
electrically.
The track is interrupted between the transistor and the first diode. The track for
construction reasons passes under a L8 coil.
Coil L8 is glued to the plate with silicone which, over time or with a blow or vibration, has
detached the track by interrupting the circuit.
To see the circuit interrupted, the coil must be unsoldered, if not, the circuit interrupted
cannot be seen.
Surely the ohmic measurement guarantees that the circuit is interrupted.
Desolder the coil L8 find the breaking point, resolder the coil.
Other information
The Finale HF plate must be totally disassembled, the driver finals and transistors from
cooling,
therefore the silicone paste must be removed clean and put back in abundance and
heterogeneous.
Last thing, and I recommend replacing all the tantalum capacitors that after years of
existence,
they are also subject to problems.
Good repair and I hope that the hours of work done by me can serve someone. best 73
from HB9TQF
************************************************************
Geräteausfall.
Fehlersuche
Da die Absorptionskraft die Hauptsicherung durchbricht, bricht die Sicherung bei der
Übertragung,
Das Problem liegt in der HF-Leistungsplatte.
Nachdem Sie den HF-Treiber des letzten Teils überprüft haben, folgen Sie dem Teil der
Gleichstromversorgung, an dem die größte Absorption auftritt
Ich kam an der Strecke an, die einen 8-V-Spannungsstabilisator zum Q6 7808 bringt.
Dann sollte der Q7 2SC880 auf seiner Basis gegen Masse I etwa 1,2 V
Schwellenspannung der beiden Dioden in Reihe finden
Bingo, es gibt keine Verbindung zur Erde durch die Dioden, die Dioden werden nicht
elektrisch gefunden.
Die Spur wird zwischen dem Transistor und der ersten Diode unterbrochen. Die Strecke
verläuft aus baulichen Gründen unter einer L8-Spule.
Die Spule L8 wird mit Silikon auf die Platte geklebt, das im Laufe der Zeit oder durch einen
Schlag oder eine Vibration die Spur durch Unterbrechen des Stromkreises gelöst hat.
Um zu sehen, dass der Stromkreis unterbrochen ist, muss die Spule entlötet sein.
Andernfalls kann der unterbrochene Stromkreis nicht gesehen werden.
Sicherlich garantiert die ohmsche Messung, dass der Stromkreis unterbrochen wird.
Entlöten Sie die Spule L8, finden Sie die Bruchstelle, lösen Sie die Spule auf.
Andere Informationen
Die Finale HF-Platte muss komplett zerlegt werden, das Treiberfinale und die Transistoren
müssen abkühlen,
Daher muss die Silikonpaste sauber entfernt und reichlich und heterogen zurückgebracht
werden.
Das Letzte, und ich empfehle, alle Tantalkondensatoren auszutauschen, die nach Jahren
des Bestehens
Sie unterliegen auch Problemen.
Gute Reparatur und ich hoffe, dass die Stunden meiner Arbeit jemandem dienen können.
am besten 73 von HB9TQF
************************************************************
Défaut de l'appareil.
Recherche de défauts
Étant donné que la puissance d'absorption rompt le fusible principal, le se rompt fusible a
la transmission,
le problème réside dans la plaque de puissance HF.
Après avoir vérifié la partie finale et pilote HF, en suivant la partie de l'alimentation DC où
la plus grande absorption vient
Je suis arrivé sur la piste qui apporte un stabilisateur de tension 8V au Q6 7808.
Ensuite, le Q7 2SC880, sur sa base vert la masse, je devrais trouver environ 1,2 V de
tension de seuil des deux diodes en série.
Bingo, il n'y a pas de connexion vert la terre à travers les diodes, les diodes ne se trouvent
pas électriquement.
La piste est interrompue entre le transistor et la première diode. La piste pour des raisons
de construction passe sous une bobine L8.
La bobine L8 est collée sur la plaque avec du silicone qui, avec le temps ou avec un coup
ou une vibration,
c'est détaché et la piste c'est cassée en interrompant le circuit.
Pour voir le circuit interrompu, la bobine doit être déssoudée, sinon, le circuit interrompu
ne peut pas être vu.
Certes, la mesure ohmique garantit que le circuit est interrompu.
Réparer le défaut
Dessouder la bobine L8 trouver le point de rupture, reparée, ressouder la bobine.
Bonne réparation et j'espère que les heures de travail effectuées par moi pourront servir
quelqu'un. meilleur 73 de HB9TQF