Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
JA592
ISTRUZIONI PER L’USO – NORME DI INSTALLAZIONE
USE AND INSTALLATION INSTRUCTIONS
INSTRUCTIONS POUR L’EMPLOI – NORMES D’INSTALLATION
INSTRUCCIONES PARA EL USO – NORMAS DE INSTALACIÓN
BETRIEBSANLEITUNG - INSTALLATIONSVORSCHRIFTEN
AVVERTENZE PER L’INSTALLATORE 8) The mechanical parts must conform to the provisions of Standards EN 12604
and EN 12605.
OBBLIGHI GENERALI PER LA SICUREZZA
For non-EU countries, to obtain an adequate level of safety, the Standards
1) ATTENZIONE! È importante per la sicurezza delle persone seguire attenta- mentioned above must be observed, in addition to national legal regulations.
mente tutta l’istruzione. Una errata installazione o un errato uso del prodotto
9) GENIUS is not responsible for failure to observe Good Technique in the
può portare a gravi danni alle persone.
construction of the closing elements to be motorised, or for any deformation
2) Leggere attentamente le istruzioni prima di iniziare l’installazione del prodot- that may occur during use.
to.
10) The installation must conform to Standards EN 12453 and EN 12445. The safety
3) I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere level of the automated system must be C+E.
lasciati alla portata dei bambini in quanto potenziali fonti di pericolo.
11) Before attempting any job on the system, cut out electrical power.
4) Conservare le istruzioni per riferimenti futuri.
12) The mains power supply of the automated system must be fitted with an all-
5) Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo pole switch with contact opening distance of 3mm or greater. Use of a 6A
indicato in questa documentazione. Qualsiasi altro utilizzo non espressamen- thermal breaker with all-pole circuit break is recommended.
te indicato potrebbe pregiudicare l’integrità del prodotto e/o rappresen-
13) Make sure that a differential switch with threshold of 0.03 A is fitted upstream
tare fonte di pericolo.
of the system.
6) GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso
14) Make sure that the earthing system is perfectly constructed, and connect
da quello per cui l’automatismo è destinato.
metal parts of the means of the closure to it.
7) Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi
15) The automated system is supplied with an intrinsic anti-crushing safety device
infiammabili costituisce un grave pericolo per la sicurezza.
consisting of a torque control. Nevertheless, its tripping threshold must be
8) Gli elementi costruttivi meccanici devono essere in accordo con quanto checked as specified in the Standards indicated at point 10.
stabilito dalle Norme EN 12604 e EN 12605.
16) The safety devices (EN 12978 standard) protect any danger areas against
Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un mechanical movement Risks, such as crushing, dragging, and shearing.
livello di sicurezza adeguato, devono essere seguite le Norme sopra riporta-
17) Use of at least one indicator-light is recommended for every system, as well
te.
as a warning sign adequately secured to the frame structure, in addition to
9) GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella co- the devices mentioned at point “16”.
struzione delle chiusure da motorizzare, nonché delle deformazioni che
18) GENIUS declines all liability as concerns safety and efficient operation of the
dovessero intervenire nell’utilizzo.
automated system, if system components not produced by GENIUS are used.
10) L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453
19) For maintenance, strictly use original parts by GENIUS.
e EN 12445. Il livello di sicurezza dell’automazione deve essere C+E.
20) Do not in any way modify the components of the automated system.
11) Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione
elettrica. 21) The installer shall supply all information concerning manual operation of the
system in case of an emergency, and shall hand over to the user the warnings
12) Prevedere sulla rete di alimentazione dell’automazione un interruttore
handbook supplied with the product.
onnipolare con distanza d’apertura dei contatti uguale o superiore a 3 mm.
È consigliabile l’uso di un magnetotermico da 6A con interruzione onnipolare. 22) Do not allow children or adults to stay near the product while it is operating.
13) Verificare che a monte dell’impianto vi sia un interruttore differenziale con 23) Keep remote controls or other pulse generators away from children, to
soglia da 0,03 A. prevent the automated system from being activated involuntarily.
14) Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi 24) Transit through the leaves is allowed only when the gate is fully open.
le parti metalliche della chiusura. 25) The user must not attempt any kind of repair or direct action whatever and
15) L’automazione dispone di una sicurezza intrinseca antischiacciamento co- contact qualified personnel only.
stituita da un controllo di coppia. E' comunque necessario verificarne la sogli 26) Anything not expressly specified in these instructions is not permitted.
di intervento secondo quanto previsto dalle Norme indicate al punto 10.
16) I dispositivi di sicurezza (norma EN 12978) permettono di proteggere even- CONSIGNES POUR L'INSTALLATEUR
tuali aree di pericolo da Rischi meccanici di movimento, come ad Es. RÈGLES DE SÉCURITÉ
schiacciamento, convogliamento, cesoiamento.
1) ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la
17) Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione lumino- lettre toutes les instructions. Une installation erronée ou un usage erroné
sa nonché di un cartello di segnalazione fissato adeguatamente sulla struttu- du produit peut entraîner de graves conséquences pour les personnes.
ra dell’infisso, oltre ai dispositivi citati al punto “16”.
2) Lire attentivement les instructions avant d'installer le produit.
18) GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funziona-
3) Les matériaux d'emballage (matière plastique, polystyrène, etc.) ne doivent
mento dell’automazione, in caso vengano utilizzati componenti dell’impian-
pas être laissés à la portée des enfants car ils constituent des sources
to non di produzione GENIUS.
potentielles de danger.
19) Per la manutenzione utilizzare esclusivamente parti originali GENIUS.
4) Conserver les instructions pour les références futures.
20) Non eseguire alcuna modifica sui componenti facenti parte del sistema
5) Ce produit a été conçu et construit exclusivement pour l'usage indiqué dans
d’automazione.
cette documentation. Toute autre utilisation non expressément indiquée
21) L’installatore deve fornire tutte le informazioni relative al funzionamento pourrait compromettre l'intégrité du produit et/ou représenter une source
manuale del sistema in caso di emergenza e consegnare all’Utente de danger.
utilizzatore dell’impianto il libretto d’avvertenze allegato al prodotto.
6) GENIUS décline toute responsabilité qui dériverait d'usage impropre ou
22) Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto différent de celui auquel l'automatisme est destiné.
durante il funzionamento.
7) Ne pas installer l'appareil dans une atmosphère explosive: la présence de
23) Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore gaz ou de fumées inflammables constitue un grave danger pour la sécurité.
di impulso, per evitare che l’automazione possa essere azionata involonta-
8) Les composants mécaniques doivent répondre aux prescriptions des Normes
riamente.
EN 12604 et EN 12605.
24) Il transito tra le ante deve avvenire solo a cancello completamente aperto.
Pour les Pays extra-CEE, l'obtention d'un niveau de sécurité approprié exige
25) L’Utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o non seulement le respect des normes nationales, mais également le respect
d’intervento diretto e rivolgersi solo a personale qualificato. des Normes susmentionnées.
26) Tutto quello che non è previsto espressamente in queste istruzioni non è 9) GENIUS n'est pas responsable du non-respect de la Bonne Technique dans la
permesso construction des fermetures à motoriser, ni des déformations qui pourraient
intervenir lors de l'utilisation.
IMPORTANT NOTICE FOR THE INSTALLER 10) L'installation doit être effectuée conformément aux Normes EN 12453 et EN
GENERAL SAFETY REGULATIONS 12445. Le niveau de sécurité de l'automatisme doit être C+E.
1) ATTENTION! To ensure the safety of people, it is important that you read 11) Couper l'alimentation électrique avant toute intervention sur l'installation.
all the following instructions. Incorrect installation or incorrect use of the 12) Prévoir, sur le secteur d'alimentation de l'automatisme, un interrupteur
product could cause serious harm to people. omnipolaire avec une distance d'ouverture des contacts égale ou supérieure
2) Carefully read the instructions before beginning to install the product. à 3 mm. On recommande d'utiliser un magnétothermique de 6A avec
3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of interruption omnipolaire.
children as such materials are potential sources of danger. 13) Vérifier qu'il y ait, en amont de l'installation, un interrupteur différentiel avec
4) Store these instructions for future reference. un seuil de 0,03 A.
5) This product was designed and built strictly for the use indicated in this 14) Vérifier que la mise à terre est réalisée selon les règles de l'art et y connecter
documentation. Any other use, not expressly indicated here, could compro- les pièces métalliques de la fermeture.
mise the good condition/operation of the product and/or be a source of 15) L'automatisme dispose d'une sécurité intrinsèque anti-écrasement, formée
danger. d'un contrôle du couple. Il est toutefois nécessaire d'en vérifier le seuil
6) GENIUS declines all liability caused by improper use or use other than that for d'intervention suivant les prescriptions des Normes indiquées au point 10.
which the automated system was intended. 16) Les dispositifs de sécurité (norme EN 12978) permettent de protéger des
7) Do not install the equipment in an explosive atmosphere: the presence of zones éventuellement dangereuses contre les Risques mécaniques du
inflammable gas or fumes is a serious danger to safety. mouvement, comme l'écrasement, l'acheminement, le cisaillement.
ITALIANO
F DL10
massa).
J3 J4 J1 J5
J5
J6 J6
2. CARATTERISTICHE TECNICHE 22 23 24 25
J3
J4 J1
1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Tensione d’alimentazione 230 V~ ( +6% -10%) - 50 Hz
FCC 2
FCA1
FCC 1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
Potenza assorbita 10 W Fig. 1
Carico max motore 800 W
Carico max accessori 0,5 A Led OP_A LED OPEN TOTALE
Carico max elettroserratura 15 VA Led OP_B LED OPEN ANTA 1 / CLOSE
Temperatura ambiente -20 °C +55 °C Led STOP LED STOP
Fusibili di protezione N° 2 (vedi fig. 1) Led FSWCL LED SICUREZZE IN CHIUSURA
Logiche di funzionamento Automatica / Semiautomatica / Sicurezza “passo Led FSWOP LED SICUREZZE IN APERTURA
passo” / Semiautomatica B / Uomo presente C / Semiautomatica “passo passo”
Led FCA1 LED FINECORSA DI APERTURA ANTA 1
Tempo d’apertura/chiusura Programmabile (da 0 a 120 s)
Led FCC1 LED FINECORSA DI CHIUSURA ANTA 1
Tempo di pausa 0, 10, 20, 30, 60, 120 s
Tempo di ritardo d’anta in chiusura 0, 5, 10, 20 s Led FCA2 LED FINECORSA DI APERTURA ANTA 2
Tempo di ritardo d’anta in apertura 2 s (Escludibile tramite dip-switch) Led FCC2 LED FINECORSA DI CHIUSURA ANTA 2
Forza di spinta Regolabile tramite dip-switch su 8 livelli per ogni motore DL10 LED SEGNALAZIONE APPRENDIMENTO TEMPI
Ingressi in morsettiera Open / Open anta svincolata / Stop / Finecorsa J1 MORSETTIERA BASSA TENSIONE
Sicurezze in ap. /Sicurezze in ch. / Alimentazione+Terra J2 CONNETTORE RAPIDO 5 PINS
Uscite in morsettiera Lampeggiatore - Motori - Aliment.accessori 24 Vdc - J3 MORSETTIERA ALIMENTAZIONE 230 VAC
Lampada spia 24 Vdc - Failsafe - Alimentazione elettroserratura 12 Vac
J4 MORSETTIERA COLLEGAMENTO MOTORI E LAMPEGGIATORE
Connettore rapido Connettore rapido 5 pins
J5 MORSETTIERA LAMPADA SPIA ED ELETTROSERRATURA
Funzioni selezionabili Logiche e tempi pausa - Forza di spinta-
Ritardo d'anta in ap. e ch. - Colpo d’inversione - J6 MORSETTIERA FINECORSA E ENCODER
Failsafe - Logica sicurezze in chiusura - Prelampeggio F1 FUSIBILE MOTORI E PRIMARIO TRASFORMATORE (F 5A)
Tasto di programmazione Apprendimento dei tempi di lavoro semplice o F2 FUSIBILE BASSA TENSIONE E ACCESSORI (T 800mA)
completo, con o senza Finecorsa e/o Encoder F PULSANTE SELEZIONE APPRENDIMENTO TEMPI
DS1 1° GRUPPO MICROINTERRUTTORI PROGRAMMAZIONE
DS2 2° GRUPPO MICROINTERRUTTORI PROGRAMMAZIONE
4. COLLEGAMENTI ELETTRICI
J6
J5
J3 22 23 24 25
J4 J1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
FCC1
FCC2
FCA1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
BLU
BLU
C1 C2
M1 M2 230 VAC
max.60W 24 Vdc
3W
230 VAC
50 Hz
ATTENZIONE:
rispettare la Per il collega-
sequenza OPEN TOTALE mento delle
fotocellule e dei 12 V ac
fase/neutro nel dispositivi di
OPEN ANTA 1
collegamento sicurezza, riferirsi
STOP FINECORSA
al paragrafo 4.1.
1
ITALIANO
4.1. Collegamento fotocellule e dispositivi di sicurezza Sicurezze in apertura/chiusura: intervengono durante i movi-
menti di apertura e chiusura del cancello, quindi sono
Prima di collegare le fotocellule (o altri dispositivi) è opportuno adatte a proteggere la zona di apertura e quella di
sceglierne il tipo di funzionamento in base alla zona di movi- chiusura dal rischio di impatto.
mento che devono proteggere (vedi fig. 3):
Sicurezze in apertura: intervengono soltanto durante il movi- Si consiglia l'utilizzo dello schema di fig.4 (nel caso di ostacoli fissi
mento di apertura del cancello, quindi sono adatte a in apertura) o dello schema di fig.5 (assenza di ostacoli fissi).
proteggere le zone tra le ante in apertura ed ostacoli
fissi (pareti, ecc.) dal rischio di impatto e schiacciamen- N.B. Se due o più dispositivi hanno la stessa funzione (apertura
to. o chiusura) vanno collegati in serie tra di loro (vedi fig.12).
Sicurezze in chiusura: intervengono soltanto durante il movi- Devono essere utilizzati contatti N.C.
mento di chiusura del cancello, quindi sono adatte a Collegamento di una coppia di fotocellule in chiusura
proteggere la zona di chiusura dal rischio di impatto. e una in apertura/chiusura (schema consigliato)
9 10 11 12 13 14 15 16 17 18 19 20 21
Sicurezze in apertura/chiusura A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
RX CL TX CL
1
2
- 1
3
+ 2
4 -
5 +
RX CL TX CL 9 10 11 12 13 14 15 16 17 18 19 20 21
1 A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
2
- 1
3
+ 2 Fig. 6
4 -
5 +
Collegamento di nessun dispositivo di sicurezza
9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
1
2
1
3 Fig. 7
2
4
RX OP TX OP
1
RX TX
2
- 1 1
3 2
+ 2
4 - - 1
3
5 + + 2
4 -
5 +
Fig. 4 Fig. 8
2
ITALIANO
3
ITALIANO
OP FSW - Contatto sicurezze in apertura (N.C.): Il compito delle 4.7. Morsettiera J6- Finecorsa e/o Encoder (fig. 2)
sicurezze in apertura è quello di salvaguardare la zona
Questi ingressi sono predisposti per la connessione di finecorsa di
interessata dal movimento delle ante durante la fase di
apertura e di chiusura che possono dare, secondo il tipo di
apertura. Nelle logiche A-SP-E-EP, durante la fase di
programmazione, l'arresto dell'anta oppure l'inizio del rallenta-
apertura, le sicurezze arrestano il movimento delle ante del
mento. I finecorsa non collegati devono essere ponticellati (se non
cancello e al disimpegno invertono il moto. Nelle logiche
B e C, durante il ciclo di apertura interrompono il movi- se ne collega nessuno, non è necessario).
mento. Non intervengono mai durante il ciclo di chiusura. E' inoltre possibile utilizzare degli encoder per rilevare la posizione
Le Sicurezze di apertura, se impegnate a cancello chiuso, angolare dell'anta e quindi avere posizioni di rallentamento e di
impediscono il movimento di apertura delle ante. arresto indipendenti dal tempo di lavoro.
I finecorsa e gli encoder sono utilizzabili anche abbinati per
Nota bene: Se non vengono collegati dispositivi di sicurez-
arrestare il movimento prima del raggiungimento della battuta
za in apertura, ponticellare gli ingressi OP e -TX FSW (fig. 7).
meccanica. Per effettuare i cablaggi seguire le fig.17a, 17b e 17c.
– - Negativo alimentazione accessori FCA1 - Finecorsa di apertura Anta 1
FCC1
FCC2
FCA1
FCA2
Se si abilita la funzione, l'apparecchiatura verifica il - - - + + -TX LOCK
+24V FSW W.L.
funzionamento delle fotocellule prima di ogni ciclo di
apertura o chiusura.
4.5. Morsettiera J5 - Lamp. Spia ed Elettroserratura (fig. 2)
W.L. - Alimentazione lampada spia
Collegare tra questo morsetto e il +24V una eventuale
lampada spia a 24 Vdc - 3 W max. Per non compro-
mettere il corretto funzionamento del sistema non
superare la potenza indicata. Fig. 17b
LOCK - Alimentazione elettroserratura
Collegare tra questo morsetto e il +24V una eventuale
elettroserratura 12 V ac.
4.6. Connettore J2 - Connettore rapido 5 pins
E' utilizzato per la connessione rapida. Innestare l'accessorio con
il lato componenti rivolto verso l'interno della scheda. Inserimento
e disinserimento vanno effettuati dopo aver tolto tensione.
ROSSO
ENCODER 1 BIANCO
NERO
ROSSO
BIANCO
ENCODER 2
NERO
Fig. 17c
ROSSO
BIANCO
ENCODER 1
NERO
RP ROSSO
BIANCO
JA592 NERO ENCODER 2
Fig. 16
N.B.: Le configurazioni indicate nei disegni sono quelle massi-
me. Sono permesse tutte le configurazioni intermedie,
utilizzando solo alcuni elementi (solo 1 encoder, solo 1
finecorsa, 2 encoder 2 finecorsa, ecc).
4
ITALIANO
FORZA ANTA 1 SW1 SW2 SW3 FORZA ANTA 2 SW4 SW5 SW6
RITARDO D'ANTA IN APERTURA (s) SW1
1 (MIN) ON ON ON 1 (MIN) ON ON ON
2 OFF ON ON 2 OFF ON ON 2 ON
3 ON OFF ON 3 ON OFF ON
0 OFF
4 OFF OFF ON 4 OFF OFF ON
5 ON ON OFF 5 ON ON OFF
6 OFF ON OFF 6 OFF ON OFF
7 ON OFF OFF 7 ON OFF OFF LOGICA FOTOCELLULE CHIUSURA SW2
8 (MAX) OFF OFF OFF 8 (MAX) OFF OFF OFF
INVERTE AL DISIMPEGNO ON
INVERTE IMMEDIATAMENTE OFF
DS1 1 2 3 4 5 6 7 8 9 10 11 12
5
ITALIANO
6.2. VERIFICA DEL SENSO DI ROTAZIONE E DELLA FORZA l'encoder, in caso contrario l'anta può non arrivare in
1) Programmare le funzioni dell’apparecchiatura elettronica battuta con il rallentamento.
secondo le proprie esigenze come da Cap.5. •Se in fase di chiusura / apertura s'interrompe il ciclo più
2) Togliere l’alimentazione all’apparecchiatura elettronica di volte consecutivamente l'anta può non arrivare in
comando. battuta con il rallentamento. Al primo ciclo completo
3) Sbloccare gli operatori e portare manualmente il cancello senza interruzioni il sistema riconoscerà le battute ed
sulla mezzeria dell’angolo d’apertura. eseguirà nuovamente i rallentamenti programmati.
4) Ribloccare gli operatori.
5) Ripristinare la tensione d’alimentazione. 6.3.2. APPRENDIMENTO CON FINECORSA
6) Inviare un comando di apertura sull’ingresso OPEN A (fig. 2)
L'apprendimento con finecorsa può essere effettuato in due
e verificare che si comandi un’apertura delle ante del
modi diversi:
cancello.
N.B.: Nel caso il primo impulso di OPEN A comandi una chiusura, - APPRENDIMENTO SEMPLICE:
è necessario togliere tensione ed invertire sulla morsettiera le Verificare che le ante siano chiuse, poi premere per 1 secondo
fasi del motore elettrico (cavi marrone e nero). il pulsante F: il led DL10 inizia a lampeggiare e le ante iniziano il
7) Verificare la regolazione della forza sui motori ed eventual- movimento di apertura.
mente modificarla (vedi Cap.5.1.). I motori si arrestano automaticamente al raggiungimento dei
N.B.: Se si utilizzano operatori oleodinamici, la forza va program- finecorsa di apertura, ma è necessario dare un impulso di OPEN
mata al massimo livello (8). A (con il radiocomando o con il pulsante a chiave) per terminare
8) Arrestare il movimento delle ante con un comando di STOP. il ciclo; le ante si fermano e il led DL10 smette di lampeggiare.
9) Sbloccare gli operatori, chiudere le ante e ribloccare gli La procedura è terminata ed il cancello è pronto per funzionare.
operatori. - APPRENDIMENTO COMPLETO:
Verificare che le ante siano chiuse, poi premere per più di 3
6.3. APPRENDIMENTO DEI TEMPI DI FUNZIONAMENTO secondi il pulsante F: il led DL10 inizia a lampeggiare e l'anta 1
Il tempo d’apertura/chiusura è determinato da una procedura inizia il movimento di apertura. Le ante rallentano automatica-
di apprendimento che varia leggermente se si utilizzano i finecorsa. mente al raggiungimento dei finecorsa, quindi è sufficiente
informare l'apparecchiatura del raggiungimento delle battute
ATTENZIONE: durante la procedura di apprendimento le sicu- tramite impulsi di OPEN A (da radiocomando o da pulsante a
rezze sono disattivate! Eseguire pertanto l'operazione evitando chiave):
qualsiasi transito nella zona di movimento delle ante. FCA1 - Rallentamento in apertura anta 1
1° OPEN - Arresto in apertura anta 1 e inizio movimento di
6.3.1. APPRENDIMENTO TEMPI NORMALE apertura anta 2
L'apprendimento normale (cioè senza finecorsa) può essere FCA2 - Rallentamento in apertura anta 2
effettuato in due modi diversi: 2° OPEN - Arresto in apertura anta 2 e inizio immediato del
- APPRENDIMENTO SEMPLICE: movimento di chiusura anta 2
Verificare che le ante siano chiuse, poi premere per 1 secondo FCC2 - Rallentamento in chiusura anta 2
il pulsante F: il led DL10 inizia a lampeggiare e le ante iniziano il 3° OPEN - Arresto in chiusura anta 2 e inizio movimento di
movimento di apertura. chiusura anta 1
Attendere l'arrivo delle ante sulla battuta di apertura e poi dare FCC1 - Rallentamento in chiusura anta 1
un impulso di OPEN A (con il radiocomando o con il pulsante a 4° OPEN - Arresto in chiusura anta 1
chiave) per arrestare il movimento: le ante si fermano e il led DL10 Il led DL10 smette di lampeggiare ed il cancello è pronto per il
smette di lampeggiare. funzionamento normale.
La procedura è terminata ed il cancello è pronto per funzionare. Note: •Se si desidera eliminare il rallentamento in alcune fasi,
- APPRENDIMENTO COMPLETO: occorre dare un impulso di Open entro 1 s. dal
Verificare che le ante siano chiuse, poi premere per più di 3 raggiungimento del finecorsa.
secondi il pulsante F: il led DL10 inizia a lampeggiare e l'anta 1 •Se alcuni finecorsa non sono installati, far iniziare il
inizia il movimento di apertura. Tramite impulsi di OPEN A (da rallentamento corrispondente con un impulso di Open
radiocomando o da pulsante a chiave) si comandano le (che sostituisce il finecorsa).
funzioni seguenti:
•Se è presente una sola anta, occorre comunque
1° OPEN - Rallentamento in apertura anta 1 eseguire l'intera sequenza. Al termine dell'apertura
2° OPEN - Arresto in apertura anta 1 e inizio movimento di dell'anta dare 5 impulsi di Open fino a che l'anta non
apertura anta 2 comincia a chiudere, poi riprendere la normale proce-
3° OPEN - Rallentamento in apertura anta 2 dura.
4° OPEN - Arresto in apertura anta 2 e inizio immediato del 6.3.3. APPRENDIMENTO TEMPI CON ENCODER
movimento di chiusura anta 2
L'apprendimento con encoder può essere effettuato in due
5° OPEN - Rallentamento in chiusura anta 2 modi diversi:
6° OPEN - Arresto in chiusura anta 2 e inizio movimento di - APPRENDIMENTO SEMPLICE:
chiusura anta 1 Verificare che le ante siano chiuse, poi premere per 1 secondo
7° OPEN - Rallentamento in chiusura anta 1 il pulsante F: il led DL10 inizia a lampeggiare e le ante iniziano il
movimento di apertura.
8° OPEN - Arresto in chiusura anta 1
Il movimento si arresta automaticamente al raggiungimento
Il led DL10 smette di lampeggiare ed il cancello è pronto per il della battuta di apertura e il led DL10 smette di lampeggiare.
funzionamento normale. La procedura è terminata ed il cancello è pronto per funzionare
utilizzando un rallentamento fisso.
Note: •Se si desidera eliminare il rallentamento in alcune fasi,
occorre attendere che l'anta arrivi in battuta e dare - APPRENDIMENTO COMPLETO:
2 impulsi di Open consecutivi (entro 1 s.). Verificare che le ante siano chiuse, poi premere per più di 3
•Se è presente una sola anta, occorre comunque secondi il pulsante F: il led DL10 inizia a lampeggiare e l'anta 1
eseguire l'intera sequenza. Al termine dell'apertura inizia il movimento di apertura.
dell'anta dare 5 impulsi di Open fino a che l'anta non Tramite impulsi di OPEN A (da radiocomando o da pulsante a
comincia a chiudere, poi riprendere la normale proce- chiave) si comandano le funzioni seguenti:
dura. 1° OPEN - Rallentamento in apertura anta 1 (si arresta
•Nell'utilizzo condominiale per garantire la ripetibilità automaticamente al raggiungimento della
del rallentamento si devono utilizzare i finecorsa o battuta)
6
ITALIANO
lampeggiante
lampeggiante
accesa
accesa
accesa
automaticamente al raggiungimento della
spenta
accesa
accesa
accesa
spenta
W.L.
W.L.
battuta)
4° OPEN - Inizio del movimento di chiusura anta 2
5° OPEN - Rallentamento in chiusura anta 2 (si arresta
automaticamente al raggiungimento della
SICUREZZE CHIUSURA
SICUREZZE CHIUSURA
eseguire l'intera sequenza. Al termine dell'apertura
Nessun effetto
Nessun effetto
Nessun effetto
Nessun effetto
comincia a chiudere, poi riprendere la normale proce-
dura.
•Per un corretto funzionamento è indispensabile avere
la battuta meccanica in apertura e chiusura.
6.3.4. APPRENDIMENTO TEMPI CON ENCODER +FINECORSA
L'apprendimento con encoder + Finecorsa può essere effettua-
to in due modi diversi:
- APPRENDIMENTO SEMPLICE:
SICUREZZE APERTURA
L'encoder è usato solo come sensore di ostacolo.
Inverte in chiusura
Inverte in chiusura
Nessun effetto
Nessun effetto
Nessun effetto
Nessun effetto
IMPULSI
- APPRENDIMENTO COMPLETO:
IMPULSI
Eseguire la stessa procedura dell'apprendimento con finecorsa.
L'encoder è usato solo come sensore di ostacolo.
Nessun effetto (OPEN inibito)
funzionamento
dura.
Blocca il
Blocca il
STOP
STOP
6.4. PRELAMPEGGIO
Se si desidera aumentare il livello di sicurezza dell'installazione, è
possibile attivare la funzione prelampeggio che consente di
accendere il lampeggiatore 5 s. prima dell'inizio del movimento
delle ante.
Riapre l'anta immediatamente (1)
Apre l'anta svincolata e richiude
Richiudel'antaimmediatamente
dopo il tempo di pausa
Bloccail funzionamento
OPEN-B
Chiude l'anta/e
Riapre leanteimmediatamente
il tempo di pausa (1)
Bloccail funzionamento
il tempo di pausa
OPEN-A
7. PROVA DELL'AUTOMAZIONE
APERTO in PAUSA
STATO CANCELLO
APERTO in PAUSA
STATO CANCELLO
IN APERTURA
IN CHIUSURA
IN CHIUSURA
BLOCCATO
IN APERTURA
BLOCCATO
CHIUSO
LOGICA "SP"
mento dell'impianto.
LOGICA "A"
Tab. 3/a
Tab. 3/b
7
Tab. 3/c
LOGICA "E" IMPULSI
STATO CANCELLO OPEN-A OPEN-B STOP SICUREZZE APERTURA SICUREZZE CHIUSURA SICUREZZA AP/CH W.L.
CHIUSO Apre le ante Apre l'anta svincolata Nessun effetto (OPEN inibito) Nessun effetto Nessun effetto (OPEN inibito) spenta
ITALIANO
APERTO Richiude le ante immediatamente Richiude l'anta immediatamente Nessun effetto Nessun effetto (OPEN inibito) accesa
Blocca il
IN CHIUSURA Riapre le ante immediatamente Riapre l'anta immediatamente funzionamento Nessun effetto (memorizza OPEN) vedi paragrafo 5.2. Blocca e al disimpegno inverte in apertura lampeggiante
IN APERTURA Blocca il funzionamento Inverte in chiusura Nessun effetto Blocca e al disimpegno continua ad aprire accesa
BLOCCATO Chiude l'anta/e Nessun effetto (OPEN inibito) Nessun effetto Nessun effetto (OPEN inibito) accesa
(con Sicurezze Chiusura impegnate, al 2° impulso apre)
Tab. 3/d
LOGICA "EP" IMPULSI
STATO CANCELLO OPEN-A OPEN-B STOP SICUREZZE APERTURA SICUREZZE CHIUSURA SICUREZZA AP/CH W.L.
CHIUSO Apre le ante Apre l'anta svincolata Nessun effetto (OPEN inibito) Nessun effetto Nessun effetto (OPEN inibito) spenta
APERTO Richiude l'anta/e immediatamente Nessun effetto (OPEN inibito) Nessun effetto (OPEN inibito) accesa
Blocca il
IN CHIUSURA Blocca il funzionamento funzionamento Nessun effetto (memorizza OPEN) vedi paragrafo 5.2. Blocca e al disimpegno inverte in apertura lampeggiante
IN APERTURA Blocca il funzionamento Inverte in chiusura Nessun effetto Blocca e al disimpegno continua ad aprire accesa
Riprende il moto in senso inverso Nessun effetto (OPEN inibito) Nessun effetto (se deve aprire, inibisce OPEN) Nessun effetto Nessun effetto (OPEN inibito) accesa
BLOCCATO (dopo uno Stop chiude sempre) (se deve chiudere, inibisce OPEN)
Tab. 3/e
LOGICA "B" IMPULSI
8
STATO CANCELLO OPEN-A OPEN-B STOP SICUREZZE APERTURA SICUREZZE CHIUSURA SICUREZZA AP/CH W.L.
Nessun effetto Nessun effetto Nessun effetto Nessun effetto spenta
CHIUSO Apre le ante o l'anta Nessun effetto (OPEN-A inibito) (OPEN-A inibito) (OPEN-A inibito)
(OPEN-B inibito)
Tab. 3/g
LOGICA "C" COMANDI SEMPRE PREMUTI IMPULSI
STATO CANCELLO OPEN-A OPEN-B STOP SICUREZZE APERTURA SICUREZZE CHIUSURA SICUREZZA AP/CH W.L.
Nessun effetto Nessun effetto Nessun effetto Nessun effetto spenta
CHIUSO Apre le ante o l'anta Nessun effetto (OPEN-A inibito)
(OPEN-A inibito) (OPEN-A inibito) (OPEN-B inibito)
Nessun effetto Nessun effetto Nessun effetto Nessun effetto
APERTO Nessun effetto Chiude le ante o l'anta (OPEN-A inibito) (OPEN-B inibito) accesa
(OPEN-B inibito) (OPEN-B inibito)
Blocca il funzionamento Blocca il funzionamento
IN CHIUSURA Blocca il funzionamento Nessun effetto lampeggiante
Blocca il (OPEN-B inibito) (OPEN-A/B inibiti)
funzionamento Blocca il funzionamento Blocca il funzionamento
IN APERTURA Blocca il funzionamento Nessun effetto accesa
(OPEN-A inibito) (OPEN-A/B inibiti)
(1) Se mantenuto prolunga la pausa fino alla disattivazione del comando (funzione timer)
(2) Nel caso il tempo pausa residuo sia inferiore a 5 sec., al disimpegno delle sicurezze chiude dopo 5 sec.
NOTA BENE: Tra parentesi gli effetti sugli altri ingressi a impulso attivo.
ENGLISH
F
- Connect the earth cable to the appropriate terminal on the J3 F DL10
noise, use separate sheaths or a shielded cable (with earthed F1 OP_A OP_B
shield). F1 Led
STOP FSWCL FSWOP
FCA1 FCA2
J1
J6
J6
J3 J4 J5
J5
22 23 24 25
2. TECHNICAL SPECIFICATIONS J3
1 2 4 5 6 7 8
J4 J1
9 10 11 12 13 14 15 16 17 18 19 20 21
FCC 2
FCA1
FCC 1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
Power supply 230 V~ ( +6% -10%) - 50 Hz
Fig. 1
Absorbedpower 10 W
Motor max. load 800 W
Led OP_A TOTALLY OPEN LED
Accessories max. load 0,5 A
Led OP_B LED: OPEN LEAF 1 / CLOSE
Electric lock max. load 15 VA
Operating ambient temperature -20 °C +55 °C
Led STOP LED STOP
Protectionfuses 2 (see fig. 1) Led FSWCL LED: CLOSING SAFETY DEVICES
Functionlogics Automatic / Semi-automatic / "Stepped" safety devices / Led FSWOP LED: OPENING SAFETY DEVICES
Semi-automatic B / Dead-man C / "Stepped" semi-automatic Led FCA1 LED: LEAF 1 OPENING LIMIT-SWITCH
Opening/closing time Programmable (from 0 to 120 s) Led FCC1 LED: LEAF 1 CLOSING LIMIT-SWITCH
Pause time 0, 10, 20, 30, 60, 120 s Led FCA2 LED: LEAF 2 OPENING LIMIT-SWITCH
Closing leaf delay 0, 5, 10, 20 s Led FCC2 LED: LEAF 2 CLOSING LIMIT-SWITCH
Opening leaf delay 2 s (Can be disabled with the dip-switch)
DL10 LED: TIME LEARNING SIGNALLING
Thrustforce Dip-switch adjustable on 8 levels for each motor
J1 LOW VOLTAGE TERMINAL BOARD
Terminal board inputs Open / Open free leaf / Stop / Limit-switch
Opening safety devices / Closing safety devices / Power supply + Earth
J2 RAPID CONNECTOR 5 PINS
Terminal board outputs Flashing lamp - Motors - 24 Vdc accessories power supply J3 230 VAC POWER SUPPLY TERMINAL BOARD
- 24 Vdc indicator-light - Fail safe - 12 Vac electric lock power supply J4 MOTORS AND FLASHING LAMP CONNECTION TERMINAL BOARD
Rapid connector Rapid connector 5 pins J5 INDICATOR-LIGHT AND ELECTRIC LOCK TERMINAL BOARD
Selectable functions Logics and pause times - Thrust force - J6 LIMIT-SWITCH AND ENCODER TERMINAL BOARD
Opening and closing leaf delay - Reversing stroke -
F1 MOTORS AND TRANSFORMER PRIMARY WINDING FUSE (F 5A)
Fail safe - Closing safety devices logic - Pre-flashing
Programming key Simple or Advanced work time learning, F2 LOW VOLTAGE AND ACCESSORIES FUSE (T 800mA)
with or without Limit-switch and/or encoder F TIME LEARNING SELECTION PUSH-BUTTON
DS1 1ST GROUP OF MICROSWITCH PROGRAMMING
DS2 2ND GROUP OF MICROSWITCH PROGRAMMING
4. ELECTRIC CONNECTIONS
J6
J5
J3 22 23 24 25
J4 J1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
FCC1
FCC2
FCA1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
BLUE
BLUE
C1 C2
M1 M2 230 VAC
max.60W 24 Vdc
3W
230 VAC
50 Hz
ATTENTION: when
connecting, observe the TOTALLY OPEN For connection of
sequence phase/neutral. the photocells 12 V ac
OPEN LEAF 1 and safety
devices, see
STOP paragraph 4.1. LIMIT-SWITCH
NB.: Capacitors are supplied with the operators. Fig. 2
9
ENGLISH
4.1. Connection of photocells and safety devices Opening/closing safety devices: they operate during the gate
opening and closing movements and, therefore, they
Before connecting the photocells (or other devices) we advise are suitable for the opening and closing areas against
you to select the type of operation according to the movement the risk of impact.
area they have to protect (see fig.3):
Opening safety devices: they operate only during the gate It is recommends use of the lay-out in fig. 4 (in the event of fixed
opening movement and, therefore, they are suitable for obstacles at opening) or in fig. 5 (no fixed obstacles).
protecting the area between the opening leaves and
fixed obstacles (walls, etc) against the risk of impact N.B. If two or more devices have the same function (opening or
and crushing. closing), they should be connected to each other in series (see
Closing safety devices: they operate only during the gate closing fig. 12). N.C. contacts must be used.
movement and, therefore, they are suitable for
Connection of a pair of closing photocells and a pair of
protecting the closing area against the risk of impact. opening/closing photocells (recommended lay-out)
9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
Opening/closing safety devices OPEN FSW +24V FSW W.L.
RX CL TX CL
1
2
- 1
3
+ 2
4 -
5 +
9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
1
2
1 Fig. 7
3
2
4
Connection of 1 pair of opening photocells
5
TX OP/CL RX OP/CL 9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
RX OP TX OP
1 RX TX
2 1
- 1 2
3
+ 2 - 1
4 - 3
+ 2
5 + 4 -
5 +
Fig. 4 Fig. 8
10
ENGLISH
Fig. 11
11
ENGLISH
OP FSW - Terminal 13 plus a negative = Opening safety devices 4.7. Terminal board J6 - Limit-switches and/or encoder(fig.2)
contact (N.C.): The purpose of the opening safety devices These inputs are designed for connection of opening and closing
are to protect the leaf movement area during opening. limit-switches which, according to type of programming - can
During opening,in the A-SP-E-EP logics, the safety devices command either leaf stop or start of deceleration. Unconnected
stop the movement of the gate leaves and reverse the
limit-switches must be jumper connected (if none are connected,
movement when they are released. During the opening
this is not necessary).
cycle in logics B and C, they interrupt movement. They
Encoders can also be used to detect the leaf's angular position
never operate during the closing cycle.
and to thus obtain deceleration and stop positions independent
If the opening safety devices operate when the gate is closed,
of work time.
they prevent the leaf opening movement.
Limit-switches and encoders can also be used in combination to
NB.: If no opening safety devices are connected, jumper stop movement before the mechanical stop limit is reached. To
connect inputs OP and -TX FSW (fig. 7). wire, see fig. 17a, 17b and 17c.
– - Terminal 14/15/16 = Negative for power supply to FCA1 - Leaf 1 opening limit-switch
accessories, are all negative. FCC1 - Leaf 1 closing limit-switch
+ - Terminal 17/18 = 24 Vdc - Positive for power supply to FCA2 - Leaf 2 opening limit-switch
accessories, are all positive. FCC2 - Leaf 2 closing limit-switch
Important: Accessories max. load is 500 mA. To calculate
absorption values, refer to the instructions for individual Fig. 17a J6
accessories. J5
FCC1
FCC2
FCA1
FCA2
supplying power to the photocell transmitters, you may, - - - + + -TX LOCK
+24V FSW W.L.
if necessary, also use the FAIL SAFE function (see
programming of microswitch DS2 - SW3).
If this function is enabled, the equipment checks
operation of the photocells before every opening or
closing cycle.
4.5. Terminal board J5 - Indicator-light and Electric lock (fig.2)
W.L. - Terminal 20 = Power supply to indicator-light
Connect a 24 Vdc - 3 W max. indicator-light, if required,
Fig. 17b
between this terminal and the +24V supply. To avoid
compromising correct operation of the system, do not
exceed the indicated power.
LOCK - Terminal 21 = Power supply to electric lock
If required/necessary, connect a 12 V ac electric lock
between terminal 21 and the terminal 18 the +24V
supply.
4.6. Connector J2 - Rapid connector 5 pins
RED
This is used for rapid connection. Connect the accessory, with WHITE
Encoder 1
BLACK
the components side facing the inside of the card. Insert and
remove only after switching off power.
RED
WHITE
Encoder 2
BLACK
Fig. 17c
RED
WHITE
BLACK
Encoder 1
RED
WHITE
Encoder 2
BLACK
RP
JA592
N.B.: Maximum configurations are shown on the drawings. All
intermediate configurations are allowed, using only some
elements (only 1 encoder, only 1 limit-switch, 2 encoders
Fig. 16
and 2 limit-switches etc.).
12
ENGLISH
5. MICROSWITCH PROGRAMMING
LEAF 1 FORCE SW1 SW2 SW3 LEAF 2 FORCE SW4 SW5 SW6
OPENING LEAF DELAY (s) SW1
1 (MIN) ON ON ON 1 (MIN) ON ON ON
2 OFF ON ON 2 OFF ON ON
2 ON
3 ON OFF ON 3 ON OFF ON
4 OFF OFF ON 4 OFF OFF ON 0 OFF
5 ON ON OFF 5 ON ON OFF
6 OFF ON OFF 6 OFF ON OFF
7 ON OFF OFF 7 ON OFF OFF CLOSING PHOTOCELL LOGIC SW2
8 (MAX) OFF OFF OFF 8 (MAX) OFF OFF OFF
REVERSES ON RELEASE ON
DS1 1 2 3 4 5 6 7 8 9 10 11 12
13
ENGLISH
6.2. ROTATION DIRECTION AND FORCE CHECK •Limit switches or encoder must be used in condominium
1) Program the functions of the control board according to applications in order to guarantee the repeatability of
need, as shown in Chapter 5. the slow-down. Otherwise the leaf could not reach the
2) Cut power to the electronic control equipment. limit stop with slow-down.
3) Release the operators and manually move the gate to the •If, during closing / opening, the cycle stops for more
mid-point of the opening angle. consecutive times, the leaf could not reach the limit
4) Re-lock the operators. stop with slow-down. At the first complete cycle without
5) Restore power. interruptions, the system recognizes the limit stops and
6) Send and opening command on the OPEN A input (fig.2) carries out again the programmed slow-downs.
and check if the gate leaves are being commanded to
open.
N.B.: If the first OPEN A pulse commands a closing, cut power and 6.3.2. LEARNING WITH LIMIT-SWITCHES
change over the phases of the electric motor (brown and Learning with limit-switches can be done in two different ways:
black wires) on the terminal board. - SIMPLE LEARNING:
7) Check power setting of the motors and, if necessary, modify Check if the leaves are closed, and then press F push-button for
it (see Chapter 5.1). 1 second: DL10 LED begins flashing and the leaves begin the
N.B.: If using hydraulic operators, force should be programmed to opening movement.
maximum level (8)
The motors stop automatically when the opening limit-switches
8) Stop leaf movement with a STOP command.
are reached, but an OPEN A pulse must be given (by radio
9) Release the operators, close the leaves and re-lock the
control or key push-button) to end the cycle; the leaves stop and
operators.
the DL10 LED stops flashing.
6.3. LEARNING OF OPERATING TIMES The procedure has ended and the gate is ready to operate.
Next pulse closes leaves and they stop on automaticaly reaching
WARNING: during the learning procedure, the safety devices are
closed position.
disabled! Therefore any transit must be avoided in the leaf
movement area when this operation is carried out. - ADVANCED COMPLETE LEARNING:
Check if the leaves are closed, and then press the F push-button
Opening/closing time is established by a learning procedure for more than 3 seconds: DL10 LED begins flashing and leaf 1
which varies slightly according to whether you are using limit-
begins the opening movement. The leaves automatically
switches.
decelerate when they reach the limit-switches, and therefore, it
6.3.1. LEARNING OF NORMAL TIMES is sufficient to inform the equipment that the stop limits have been
reached by means of OPEN A pulses (by radio control or key push-
- SIMPLE LEARNING:
button):
Check if the leaves are closed, and then press F push-button for
FCA1 - Deceleration at opening of leaf 1
one second: DL10 LED begins flashing and the leaves begin the
opening movement. 1° OPEN - Leaf 1 stops at opening and leaf 2 begins its
Wait for the leaf to reach the opening stop limit and then supply opening movement
an OPEN A pulse (with the radio control or with the key controlled FCA2 - Deceleration at opening of leaf 2
push-button) to stop the movement: the leaves stop and the 2° OPEN - Leaf 2 stops at opening and immediately begins
DL10 LED stops flashing. its closing movement
The procedure has ended and the gate is ready to operate. FCC2 - Deceleration at closing of leaf 2
Next pulse closes leaves and they stop on automaticaly reaching 3° OPEN - Leaf 2 stops at closing and leaf 1 begins its closing
closed position. movement
- ADVANCED COMPLETE LEARNING: FCC1 - Deceleration at closing of leaf 1
Check if the leaves are closed, and then press F push-button for 4° OPEN - Leaf 1 stops at closing
more than 3 seconds: DL10 LED begins flashing and the leaf 1 the DL10 LED stops flashing and the gate is ready for normal
begins the opening movement. The following functions can be operation
commanded by the OPEN A pulses (by radio control or key
Notes:•If you wish to eliminate deceleration in some stages, you
controlled push-button):
must supply an Open pulse within 1 second of reaching
1° OPEN - Deceleration at opening of leaf 1 the limit-switch.
2° OPEN - Leaf 1 stops at opening and leaf 2 begins its •If some limit-switches are not installed, start the
opening movement corresponding deceleration by supplying an Open
3° OPEN - Deceleration at opening of leaf 2 pulse (which replaces the limit-switch).
4° OPEN - Leaf 2 stops at opening and immediately begins •If only one leaf is present, the entire sequence must
its closing movement nevertheless be effected. When the leaf has finished
opening, supply 5 Open pulses until the leaf begins to
5° OPEN - Deceleration at closing of leaf 2
close, and then resume normal operation.
6° OPEN - Leaf 2 stops at closing and leaf 1 begins its closing •It wind effected areas it is best to allow 2 second after
movement the leaf reaches open stop befor supplying Open A to
7° OPEN - Deceleration at closing of leaf 1 ensure full closing.
8° OPEN - Leaf 1 stops at closing
The DL10 LED stops flashing and the gate is ready for normal 6.3.3. LEARNING TIMES WITH ENCODER
operation. Learning with the encoder can be done in two different ways:
Notes: •If you wish to eliminate deceleration in certain stages,
wait for the leaf to reach its stop-limit and supply 2 - SIMPLE LEARNING:
consecutive Open pulses (by 1 second). Check if the leaves are closed, and then press F push-button for
•If only one leaf is present, the entire sequence must 1 second: DL10 LED begins flashing and the leaves begin the
nevertheless be effected. When the leaf has finished opening movement.
opening, supply 5 Open pulses until the leaf begins to The movement stops automatically when the opening stop limit
close, and then resume normal operation. is reached and the DL10 LED stops flashing.
•It wind effected areas it is best to allow 2 second after The procedure has ended and the gate is ready to operate,
the leaf reaches open stop befor supplying Open A to using fixed deceleration.
ensure full closing.
14
ENGLISH
- COMPLETE LEARNING:
Check if the leaves are closed, and then press the F push-button for
more than 3 seconds: DL10 LED begins flashing and leaf 1 begins the
flashing
flashing
lighted
lighted
lighted
lighted
lighted
lighted
W.L.
W.L.
OFF
OFF
opening movement. The following functions can be commanded by
the OPEN A pulses (by radio control or key push-button):
1° OPEN - Leaf 1 Decelerates at opening (it stops automatically
Locksand,onrelease,reversesatopening
2° OPEN - Leaf 2 opening movement begins
Locksand,onrelease,continuesopening
Noeffect(OPENdisabled)
on reaching the stop limit)
4° OPEN - Leaf 2 closing movement begins
5° OPEN - Leaf 2 decelerates at closing (it stops automatically on
Freezespauseuntilrelease(2)(OPENdisabled)
reaching the stop limit)
seeparagraph5.2.
No effect
No effect
Noeffect
Noeffect
•If only one leaf is present, the entire sequence must
nevertheless be effected. When the leaf has finished opening,
supply 5 Open pulses until the leaf begins to close, and then
resume normal operation.
•For a correct operation, the mechanical limit stop during
opening and closing is absolutely necessary.
6.3.4. LEARNING TIMES WITH ENCODER + LIMIT-SWITCHES
Learning with the encoder + Limit-switches can be done in two different OPENING SAFETY DEVICES
Reverses at closing
Reverses atclosing
- SIMPLE LEARNING:
PULSES
PULSES
Noeffect
No effect
No effect
Noeffect
Carry out the same procedure as for limit-switch learning. The encoder
is used only as an obstacle sensor.
Carry out the same procedure as for limit-switch learning. The encoder
is used only as an obstacle sensor.
Note: •If some limit-switches are not installed, start the corresponding
deceleration by supplying an Open pulse (which replaces
the limit-switch).
Stops operation
Stopsoperation
STOP
supply 5 Open pulses until the leaf begins to close, and then
resume normal operation.
6.4. PRE-FLASHING
If you wish to increase the equipment's safety level, you can activate
Opensthefreeleafandclosesafterpause
Re-closestheleafimmediately
OPEN-B
time (1)
active)
No effect (1)
4 - briefly press the F push-button and check if the DL10 LED lights
up.
Opens leaves and closes them after
Re-opens the leaves immediately(1)
Opensleavesandclosesthemafter
Stops operation
pausetime(1)
OPEN-A
pause time
OPEN on PAUSE
GATE STATUS
AT CLOSING
AT OPENING
GATE STATUS
LOCKED
CLOSED
Table 3/b
LOGIC "SP"
15
Table 3/c
LOGIC "E" PULSES
GATE STATUS OPEN-A OPEN-B STOP OPENING SAFETY DEVICES CLOSING SAFETY DEVICES OP/CLOS. SAFETY DEVICE W.L.
CLOSED Opens the leaves Opens the free leaf No effect (OPEN disabled) No effect No effect (OPEN disabled) OFF
ENGLISH
OPEN Re-closes the leaves immediately Re-closes the leaf immediately No effect No effect (OPEN disabled) lighted
Stops operation
AT CLOSING Re-opens the leaves immediately Re-opens the leaf immediately (1) No effect (saves OPEN) see paragraph 5.2. Locks and, on release, reverses at opening flashing
AT OPENING Stops operation Reverses at closing No effect Locks and, on release, continues opening lighted
Closes the leaf/leaves No effect (OPEN disabled) No effect No effect (OPEN disabled) lighted
LOCKED (with CLOSING SAFETY DEVICES active, opens at 2nd pulse)
Table 3/d
LOGIC "EP" PULSES
GATE STATUS OPEN-A OPEN-B STOP OPENING SAFETY DEVICES CLOSING SAFETY DEVICES OP/CLOS. SAFETY DEVICE W.L.
CLOSED Opens the leaves Opens the free leaf No effect (OPEN disabled) Noeffect No effect (OPEN disabled) OFF
OPEN Re-closes the leaf/leaves immediately No effect (OPEN disabled) No effect (OPEN disabled) lighted
Stops operation
AT CLOSING Stops operation No effect (saves OPEN) see paragraph 5.2. Locks and, on release, reverses at opening flashing
Table 3/e
PULSES
16
LOGIC "B"
GATE STATUS OPEN-A OPEN-B STOP OPENING SAFETY DEVICES CLOSING SAFETY DEVICES OP/CLOS. SAFETY DEVICE W.L.
Noeffect Noeffect Noeffect Noeffect OFF
CLOSED Opens the leaf or leaves Noeffect (OPEN-A disabled) (OPEN-A disabled) (OPEN-A disabled)
(OPEN-B disabled)
Table 3/f
LOGIC "C" COMMANDS ALWAYS PRESSED PULSES
GATE STATUS OPEN-A OPEN-B STOP OPENING SAFETY DEVICES CLOSING SAFETY DEVICES OP/CLOS. SAFETY DEVICE W.L.
Noeffect Noeffect Noeffect Noeffect OFF
CLOSED Opens the leaf or leaves Noeffect
(OPEN-A disabled) (OPEN-A disabled) (OPEN-B disabled) (OPEN-A disabled)
(1) If maintained, it prolongs the pause until disabled by the command (timer function)
(2) If remaining pause time is shorter than 5 sec., when safety devices are released, it closes after 5 sec.
NB.: Effects on other active pulse inputs in brackets.
FRANÇAIS
J6 J6
J4 J1 J5
J5
J3 J3 J4 J1
22 23 24 25
1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
FCC 2
FCA1
FCC 1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
J6
J5
J3 22 23 24 25
J4 J1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
FCC1
FCC2
FCA1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
BLEU
BLEU
C1 C2
M1 M2 230 VAC
max.60W 24 Vdc
3W
230 VAC
50 Hz
17
FRANÇAIS
4.1. Connexion des photocellules et des dispositifs de sécurité Sécurités en ouverture/fermeture: elles interviennent durant les
mouvements d'ouverture et fermeture du portail, elles
Avant de connecter les photocellules (ou d'autres dispositifs), il sont dont indiquées pour protéger la zone d'ouverture
est opportun d'en choisir le type de fonctionnement en fonction et la zone de fermeture contre le risque d'impact.
de la zone de mouvement qu'elles doivent protéger (voir fig. 3):
Sécurités en ouverture: elles interviennent uniquement durant le On préconise l'utilisation du schéma de la fig.4 (en cas d'obstacles
mouvement d'ouverture du portail, elles sont donc fixes en ouverture) ou du schéma de la fig.5 (absence d'obstacles
indiquées pour protéger les zones entre les vantaux en fixes).
ouverture et les obstacles fixes (murs, etc.) contre le
risque d'impact et d'écrasement. N.B. Si deux dispositifs ou plus ont la même fonction (ouverture
ou fermeture), ils faut les connecter en série entre eux (voir
Sécurités en fermeture: elles interviennent uniquement durant le fig.12). Il est nécessaire d'utiliser des contacts N.F.
mouvement de fermeture du portail, elles sont donc
indiquées pour protéger la zone de fermeture contre le Connexion d'une paire de photocellules en fermeture, et d'une paire
risque d'impact. de photocellules en ouverture/fermeture (schéma préconisé)
9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
Sécurités en ouverture/fermeture OPEN FSW +24V FSW W.L.
RX CL TX CL
1
2
- 1
3
+ 2
4 -
5 +
Sécurités en fermeture 1
Sécurités en
ouverture 2
Fig. 3 1
3
2
4
Connexion d'une paire de photocellules en fermeture, d'une paire
de photocellules en ouverture et d'une paire de photocellules en 5
ouverture/fermeture (schéma préconisé)
TX OP/CL RX OP/CL
9 10 11 12 13 14 15 16 17 18 19 20 21 Fig. 5
A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
Connexion d'un dispositif de sécurité en fermeture et d'un dispositif
de sécurité en ouverture
9 10 11 12 13 14 15 16 17 18 19 20 21
RX CL TX CL A B STP CL OP - - - + + -TX LOCK
1 OPEN FSW +24V FSW W.L.
2
- 1 Fig. 6
3
+ 2
4 -
5 + Connexion d'aucun dispositif de sécurité
9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
1
2 Fig. 7
1
3
2
4
Connexion d'une paire de photocellules en ouverture
5 9 10 11 12 13 14 15 16 17 18 19 20 21
TX OP/CL RX OP/CL A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
RX OP TX OP
RX TX
1
1
2
2
- 1
3 - 1
+ 2 3
4 - + 2
4 -
5 + +
5
Fig. 4 Fig. 8
18
FRANÇAIS
Fig. 12
RX TX
Connexion de 2 contacts N.O. en parallèle
1
(Ex.: Open A, Open B)
2
- 1
3
+ 2
4 -
5 +
Fig. 9
Fig. 13
Connexion d'une paire de photocellules en ouverture et d'une
paire de photocellules en fermeture
4.2. Bornier J3 - Alimentation (fig. 2)
9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK PE: Connexion de terre
OPEN FSW +24V FSW W.L. N : Alimentation 230 V~ ( Neutre )
L : Alimentation 230 V~ ( Ligne )
Nota bene: Pour un fonctionnement correct, il est obligatoire de
connecter la platine au conducteur de terre présent dans
RX OP TX OP l'installation. Prévoir en amont du système un disjoncteur
1
magnétothermique différentiel adéquat.
2
- 1 4.3. Bornier J4 - Moteurs et feu clignotant (fig. 2)
3
+ 2 M1 : COM / OP / CL: Connexion Moteur 1
4 -
Utilisable dans l'application d'un vantail unique
5 + M2 : COM / OP / CL: Connexion Moteur 2
Non utilisable dans l'application d'un vantail unique
LAMP : Sortie feu clignotant ( 230 V ~)
TX CL RX CL
4.4. Bornier J1 - Accessoires (fig. 2)
1
2 OPEN A - Commande d'"Ouverture Totale" (N.O.): on désigne par
1 - là tout générateur d'impulsion (poussoir, detector, etc.) qui,
3 en fermant un contact, commande l'ouverture et/ou la
2 +
- 4 fermeture des deux vantaux du portail.
+ 5 Pour installer plusieurs générateurs d'impulsion d'ouverture
totale, connecter les contacts N.O. en parallèle (fig.13).
OPEN B - Commande d'"Ouverture partielle" (N.O.) / Fermeture:
on désigne par là tout générateur d'impulsion (poussoir,
Fig. 10
detector, etc.) qui, en fermant un contact, commande
l'ouverture et/ou la fermeture du vantail commandé par le
Connexion de deux paires de photocellules en fermeture moteur M1. Dans les logiques B et C, il commande toujours
9 10 11 12 13 14 15 16 17 18 19 20 21 la fermeture des deux vantaux.
A B STP CL OP - - - + + -TX LOCK Pour installer plusieurs générateurs d'impulsion d'ouverture
OPEN FSW +24V FSW W.L. partielle, connecter les contacts N.O. en parallèle (fig.13).
STP - Contact de STOP (N.F.): on désigne par là tout dispositif (Ex.:
poussoir) qui, en ouvrant un contact, peut arrêter le mouvement
du portail.
RX CL1 TX CL1 Pour installer plusieurs dispositifs de STOP, connecter les contacts
1 N.F. en série (voir fig.12).
2 Nota bene: Si on ne connecte aucun dispositif de STOP, ponter
- 1 les bornes STP et -.
3
+ 2 CL FSW - Contact des sécurités en fermeture (N.F.): La fonction
4 -
des sécurités en fermeture est de protéger la zone concernée
5 + contre le mouvement des vantaux durant la phase de
fermeture. Dans les logiques A-SP-E-EP, durant la phase de
fermeture, le sécurités intervertissent le mouvement des
TX CL2 RX CL2 vantaux du portail, ou arrêtent et intervertissent le
mouvement à leur désengagement (voir programmation
1
microinterrupteur DS2-SW2). Dans les logiques B et C, durant
2
1
le cycle de fermeture elles interrompent le mouvement. Elles
3 n'interviennent jamais durant le cycle d'ouverture. Les
2 Sécurités de fermeture, si elles sont engagées avec le portail
4
ouvert, empêchent le mouvement de fermeture des
5 vantaux.
Nota bene: Si on ne connecte aucun dispositif de sécurité
en fermeture, ponter les bornes CL et -TX FSW (fig. 7).
Fig. 11
19
FRANÇAIS
OP FSW - Contact des sécurités en ouverture (N.F.): La fonction 4.7. Bornier J6- Fins de course et/ou encodeur(fig. 2)
des sécurités en ouverture est de protéger la zone concernée Ces entrées sont prédisposées pour la connexion de fins de course
contre le mouvement des vantaux durant la phase d'ouverture et de fermeture qui peuvent donner, suivant le type
d'ouverture. Dans les logiques A-SP-E-EP, durant la phase de programmation, l'arrêt du vantail ou le début du ralentissement.
d'ouverture, le sécurités arrêtent le mouvement des vantaux Les fins de course non connectés doivent être pontés (si on ne
du portail et, au désengagement, elles intervertissent le connecte aucun fin de course, le pontage n'est pas nécessaire).
mouvement. Dans les logiques B et C, durant le cycle En outre, il est possible d'utiliser les encodeurs pour détecter la
d'ouverture, elles interrompent le mouvement. Elles position angulaire du vantail et pour avoir par conséquent des
n'interviennent jamais durant le cycle de fermeture. positions de ralentissement et d'arrêt indépendantes du temps de
Les Sécurités d'ouverture, si elles sont engagées avec le fonctionnement.
portail fermé, empêchent le mouvement d'ouverture des Les fins de course et les encodeurs sont également utilisés pour
vantaux. arrêter le mouvement avant d'atteindre la butée mécanique.
Nota bene: Si on ne connecte aucun dispositif de sécurité Pour réaliser les câblages, suivre les fig.17a, 17b et 17c.
en ouverture, ponter les entrées OP et -TX FSW (fig. 7). FCA1 - Fin de course d'ouverture du Vantail 1
– - Négatif alimentation des accessoires FCC1 - Fin de course de fermeture du Vantail 1
+ - 24 Vcc - Positif alimentation des accessoires FCA2 - Fin de course d'ouverture du Vantail 2
Attention:La charge maxi des accessoires est de 500 mA. FCC2 - Fin de course de fermeture du Vantail 2
Pour calculer les absorptions, se reporter aux instructions de
chaque accessoire. Fig. 17a J6
J5
-TX FSW - Négatif alimentation des émetteurs photocellules
En utilisant cette borne pour la connexion du négatif de
22 23 24 25
l'alimentation des émetteurs photocellules, on peut
éventuellement utiliser la fonction FAILSAFE (voir 14 15 16 17 18 19 20 21
FCC1
FCC2
FCA1
FCA2
programmation microinterrupteur DS2-SW3). - - - + + -TX LOCK
Si on valide la fonction, la platine vérifie le fonctionnement +24V FSW W.L.
des photocellules avant chaque cycle d'ouverture ou
fermeture.
4.5. Bornier J5 - Lampe-Témoin et Electroserrure (fig. 2)
W.L. - Alimentation lampe-témoin
Connecter entre cette borne et le +24V une lampe-témoin
éventuelle à 24 Vcc - 3 W maxi. Pour ne pas compromettre
le fonctionnement correct du système, ne pas dépasser la Fig. 17b
puissance indiquée.
LOCK - Alimentation électroserrure
Connecter entre cette borne et le +24V une électroserrure
éventuelle de 12 Vca.
4.6. Connecteur J2 - Connecteur rapide 5 pins
On l'utilise pour la connexion rapide. Embrocher l'accessoire de
manière à ce que le côté de ses composants soit tourné vers
l'intérieur de la platine. Branchement et débranchement doivent
s'effectuer après coupé le courant. ROUGE
BLANC
ENCODEUR 1
NOIR
ROUGE
ENCODEUR 2 BLANC
NOIR
Fig. 17c
ROUGE
BLANC
NOIR ENCODEUR 1
ROUGE
BLANC
ENCODEUR 2
NOIR
RP
JA592 N.B.: Les configurations indiquées sur les dessins sont maximales.
Toutes les configurations intermédiaires sont permises, en
Fig. 16 utilisant seulement certains éléments (seulement 1 encodeur,
seulement 1 fin de course, 2 encodeurs et 2 fins de course,
etc.).
20
FRANÇAIS
DS1 1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4
DS2
LOGIQUE PAUSE (s) SW7 SW8 SW9 SW10
E / ON ON ON ON
EP / OFF ON ON ON
B / ON OFF ON ON FAILSAFE SW3
C / OFF OFF ON ON
A 0 ON ON OFF ON RETARD DE VANTAIL OUI ON
A 10 OFF ON OFF ON SW11 SW12
EN FERMETURE (s)
A 20 ON OFF OFF ON
NON OFF
20 ON ON
A 30 OFF OFF OFF ON
10 OFF ON
A 60 ON ON ON OFF 5 ON OFF COUP D'INVERSION
A 120 OFF ON ON OFF 0 OFF OFF + COUP DE BÉLIER SW4
SP 0 ON OFF ON OFF
SP 10 OFF OFF ON OFF SI ON
SP 20 ON ON OFF OFF NO OFF
SP 30 OFF ON OFF OFF
SP 60 ON OFF OFF OFF
Fig. 18 SP 120 OFF OFF OFF OFF
Fig. 19
La platine est dotée de deux groupes de microinterrupteurs DS1 Failsafe actif, la platine procède à une vérification des
(fig. 18) et DS2 (fig.19) qui permettent de programmer les photocellules avant chaque mouvement d'ouverture et
paramètres de fonctionnement du portail. fermeture.
Coup d'inversion + coup de bélier
5.1. MICROINTERRUPTEURS DS1 (fig.18) Grâce au microinterrupteur SW4, il est possible d'activer le "coup
Force Vantail 1 et 2 d'inversion" et le "coup de bélier". Le "coup d'inversion" pousse
Par l'intermédiaire des microinterrupteurs SW1, SW2 et SW3, il est pendant un instant les vantaux en fermeture avant d'effectuer
possible de programmer la force (et donc la sécurité anti- l'ouverture du portail, en facilitant le déclenchement de
écrasement) de l'opérateur connecté au vantail 1. La même l'électroserrure. Le "coup de bélier" commande une poussée en
opération devra être effectuée pour le moteur connecté au fermeture à pleine puissance lorsque le portail a déjà atteint la
vantail 2, en agissant sur les microinterrupteurs SW4, SW5 et SW6. butée, en facilitant l'enclenchement de l'électroserrure.
Logique de fonctionnement 6. MISE EN FONCTION
Grâce aux microinterrupteurs SW7, SW8, SW9 et SW10, il est
possible de choisir la logique de fonctionnement de l'automatisme. 6.1. Vérification des LEDs
En sélectionnant une logique automatique (A, SP), la combinaison Le tableau ci-après reporte l'état des Leds en relation avec l'état
des microinterrupteurs permet de choisir également le temps de des entrées.
pause (temps d'attente, en position ouverte, avant la refermeture Noter que: LED ALLUMÉE = contact fermé
automatique). LED ÉTEINTE = contact ouvert
Les logiques disponibles, dont le fonctionnement est décrit dans Vérifier l'état des leds de signalisation comme l'indique le Tableau.
les tableaux 3/a-b-c-d-e-f, sont les suivantes: A - SP
(Automatiques), et E-EP-B (Semi-automatiques), C (Homme mort). Fonctionnement leds de signalisation d'état
Retard de vantail en fermeture LEDS ALLUMÉE ÉTEINTE
La programmation des microinterrupteurs SW11 et SW12 permet OP_A Commande activée Commandeinactive
de retarder le départ en fermeture du vantail 1 par rapport au OP_B Commande activée Commandeinactive
vantail 2, pour éviter la superposition des vantaux durant le STOP Commandeinactive Commande activée
mouvement et donc augmenter la sécurité de l'installation. FSWCL Sécuritésdésengagées Sécurités engagées
FSWOP Sécuritésdésengagées Sécurités engagées
5.2. MICROINTERRUPTEURS DS2 (fig.19) FCA1 (si utilisée) Fin de course libre Fin de course engagé
Retard de vantail en ouverture FCC1 (si utilisée) Fin de course libre Fin de course engagé
La programmation du microinterrupteur SW1 permet de retarder FCC2 (si utilisée) Fin de course libre Fin de course engagé
le départ en ouverture du vantail 2 par rapport au vantail 1, pour FCA2 (si utilisée) Fin de course libre Fin de course engagé
éviter que les vantaux ne soient gênés l'un par l'autre durant la
phase initiale du mouvement.
Nota bene: En caractères gras, la condition des leds avec le portail au
Logique photocellules en fermeture repos.
Grâce au microinterrupteur SW2, on peut choisir le type de
comportement de l'automatisme au cas où les photocellules qui En outre, sur la platine se trouve la Led DL10 qui fonctionne
protègent le mouvement de fermeture du portail seraient comme l'indique le tableau suivant:
engagée. Il est possible d'obtenir l'inversion immédiate des vantaux
ou l'arrêt avec inversion au désengagement des photocellules. DL10
Failsafe Portail fermé au repos: Portail en mouvement Apprentissage temps:
La programmation du microinterrupteur SW3 permet d'activer éteinte ou pause: clignote rapidement
ou de désactiver le test de contrôle des photocellules. Grâce au comme lampe-témoin
21
FRANÇAIS
6.2. VERIFICATION DU SENS DE ROTATION ET DE LA FORCE •Dans le cas d’une utilisation collective, pour garantir
1) Programmer les fonctions de la platine électronique suivant la répétabilité du ralentissement, utiliser les fins de
les exigences propres comme au Chap.5. course ou l’encoder; dans le cas contraire, le vantail ne
2) Couper le courant à la platine électronique de commande. peut pas arriver à la butée avec le ralentissement
3) Débloquer les opérateurs et amener manuellement le portail •Si, en phase de fermeture / ouverture, on interrompt le
au centre de l'angle d'ouverture. cycle plusieurs fois de suite, le vantail peut ne pas
4) Rebloquer les opérateurs. arriver à la butée avec le ralentissement. Au premier
5) Rétablir le courant. cycle complet sans interruptions, le système reconnaîtra
6) Envoyer une commande d'ouverture sur l'entrée OPEN A (fig. 2) et les butées et exécutera de nouveau les ralentissements
vérifier qu'on commande une ouverture des vantaux du portail. programmés.
N.B.: Si la première impulsion d'OPEN A commande une fermeture,
il est nécessaire de couper le courant et d'intervertir sur le 6.3.2. APPRENTISSAGE AVEC FINS DE COURSE
bornier de la platine les phases du moteur électrique (câbles L'apprentissage avec les fins de course peut être effectué de
marron et noir). deux façons différentes:
7) Vérifier le réglage de la force sur les moteurs et éventuellement - APPRENTISSAGE SIMPLE:
la modifier (voir Chap.5.1.). Vérifier que les vantaux sont fermés, puis appuyer pendant 1
N.B.: Si on utilise des opérateurs oléo-dynamiques, la force doit seconde sur le poussoir F: la led DL10 commence à clignoter et
être programmée au niveau maximal (8) les vantaux commencent le mouvement d'ouverture.
8) Arrêter le mouvement des vantaux avec une commande Les moteurs s'arrêtent automatiquement lorsque les fins de course
de STOP. d'ouverture sont atteints, mais il est nécessaire de donner une
9) Débloquer les opérateurs, fermer les vantaux et rebloquer les impulsion d'OPEN A (avec la radiocommande ou avec le poussoir
opérateurs. à clé) pour terminer le cycle; les vantaux s'arrêtent et la led DL10
cesse de clignoter.
6.3. APPRENTISSAGE DES TEMPS DE FONCTIONNEMENT La procédure est terminée et le portail est prêt à fonctionner.
22
FRANÇAIS
clignotante
clignotante
suivantes:
allumée
allumée
allumée
allumée
allumée
allumée
éteinte
éteinte
W.L.
W.L.
1er OPEN - Ralentissement en ouverture du vantail 1 (il s'arrête
automatiquement lorsque la butée est atteinte)
2e OPEN - Début du mouvement d'ouverture du vantail 2
3e OPEN - Ralentissement en ouverture du vantail 2 (il s'arrête
Bloqueetaudésengagementintervertiten
Bloqueetaudésengagementcontinueà
Bloqueetaudésengagementcontinueà
Bloqueetaudésengagementintervertiten
automatiquement lorsque la butée est atteinte)
4e OPEN - Début du mouvement de fermeture du vantail 2
Aucuneffet(OPENinhibé)
Aucuneffet(OPENinhibé)
SÉCURITÉ OUV/FERM
SÉCURITÉ OUV/FERM
5e OPEN - Ralentissement en fermeture du vantail 2 (il s'arrête
Congèlelapausejusqu'audésengagement(2)(OPENinhibé)
automatiquement lorsque la butée est atteinte)
ouverture
ouverture
ouvrir
ouvrir
6e OPEN - Début du mouvement de fermeture du vantail 1
7e OPEN - Ralentissement en fermeture du vantail 1 (il s'arrête
automatiquement lorsque la butée est atteinte)
Aucuneffet(OPENinhibé)
Aucuneffet(OPENinhibé)
fonctionnement normal.
Notes: •L'impulsion de ralentissement doit être donnée avec une
certaine avance par rapport à la butée pour éviter que
le vantail ne l'atteigne à pleine vitesse (elle serait dans ce
cas interprétée comme un obstacle).
SÉCURITÉS FERMETURE
SÉCURITÉS FERMETURE
voirparagraphe5.2.
voirparagraphe5.2.
•Dans le cas d'un seul vantail, il faut quoi qu'il en soit
Aucuneffet
Aucuneffet
Aucuneffet
Aucuneffet
exécuter toute la séquence. Au terme de l'ouverture du
vantail, donner 5 impulsions d'Open jusqu'à ce que le
vantail commence à se fermer, puis reprendre la procédure
normale.
•Pour un fonctionnement correct, il est indispensable
d'avoir la butée mécanique en ouverture et fermeture.
6.3.4. APPRENTISSAGE DES TEMPS AVEC ENCODEUR + FINS DE COURSE
Aucuneffet(mémoriseOPEN)
SÉCURITÉS OUVERTURE
SÉCURITÉS OUVERTURE
Intervertit en fermeture
- APPRENTISSAGE SIMPLE:
Intervertit en fermeture
IMPULSIONS
IMPULSIONS
Exécuter la même procédure que l'apprentissage avec les fins de
Aucuneffet
Aucuneffet
Aucuneffet
Aucuneffet
course. Le encodeur n'est utilisé que comme un détecteur d'obstacle.
- APPRENTISSAGE COMPLET:
Aucuneffet(OPENinhibé)
Aucuneffet(OPENinhibé)
Exécuter la même procédure que l'apprentissage avec les fins de
course. Le encodeur n'est utilisé que comme un détecteur d'obstacle.
Notes: •Si certains fins de course ne sont pas installés, faire
commencer le ralentissement correspondant par une
impulsion d'Open (qui substitue le fin de course).
•Dans le cas d'un seul vantail, il faut quoi qu'il en soit
Aucuneffet(OPENinhibé)
Aucuneffet(OPENinhibé)
exécuter toute la séquence. Au terme de l'ouverture
lefonctionnement
lefonctionnement
du vantail, donner 5 impulsions d'Open jusqu'à ce que
Bloque
Bloque
STOP
STOP
Rouvrelevantailimmédiatement
Rouvrelevantailimmédiatement
Bloque le fonctionnement
immédiatement
letempsdepause
OPEN-B
(1)
Fermele(s)vantail(vantaux)
3 - vérifier que la led DL10 est éteinte (si elle est allumée, le
pré-clignotement est déjà actif)
Aucuneffet(1)
Rouvrelesvantauximmédiatement
Ouvrelesvantauxetrefermeaprès
Ouvrelesvantauxetrefermeaprès
immédiatement
letempsdepause
OPEN-A
(1)
OUVERT en PAUSE
EN OUVERTURE
EN OUVERTURE
EN FERMETURE
EN FERMETURE
ÉTAT PORTAIL
ÉTAT PORTAIL
Tableau 3/b
Tableau 3/a
BLOQUÉ
BLOQUÉ
7. ESSAI DE L'AUTOMATISME
FERMÉ
FERMÉ
LOGIQUE "SP"
LOGIQUE "A"
23
Tableau 3/c
LOGIQUE "E" IMPULSIONS
ÉTAT PORTAIL OPEN-A OPEN-B STOP SÉCURITÉS OUVERTURE SÉCURITÉS FERMETURE SÉCURITÉ OUV/FERM W.L.
Tableau 3/d
LOGIQUE "EP" IMPULSIONS
ÉTAT PORTAIL OPEN-A OPEN-B STOP SÉCURITÉS OUVERTURE SÉCURITÉS FERMETURE SÉCURITÉ OUV/FERM W.L.
FERMÉ Ouvre les vantaux Ouvre le vantail dégagé Aucun effet (OPEN inhibé) Aucun effet Aucun effet (OPEN inhibé) éteinte
OUVERT Referme le(s) vantail(vantaux) immédiatement Aucun effet (OPEN inhibé) Aucun effet (OPEN inhibé) allumée
Bloque
EN FERMETURE Bloque le fonctionnement le fonctionnement Aucun effet (mémorise OPEN) voir paragraphe 5.2. Bloque et au désengagement clignotante
intervertit en ouverture
EN OUVERTURE Bloque le fonctionnement Intervertit en fermeture Aucun effet Bloque et au désengagement allumée
continue à ouvrir
Reprend le mouvement en sens inverse Aucun effet (si elle doit ouvrir, elle inhibe Aucun effet
BLOQUÉ (après un Stop ferme toujours)
Aucun effet (OPEN inhibé) Aucun effet (OPEN inhibé) allumée
OPEN) (si elle doit fermer, elle inhibe OPEN)
24
Tableau 3/e
LOGIQUE "B" IMPULSIONS
ÉTAT PORTAIL OPEN-A OPEN-B STOP SÉCURITÉS OUVERTURE SÉCURITÉS FERMETURE SÉCURITÉ OUV/FERM W.L.
Aucun effet Aucun effet Aucun effet Aucun effet éteinte
FERMÉ Ouvre les vantaux ou le vantail Aucun effet (OPEN-A inhibé) (OPEN-A inhibé) (OPEN-A inhibé)
(OPEN-B inhibé)
Tableau 3/f
LOGIQUE "C" COMMANDES TOUJOURS ENFONCEES IMPULSIONS
ÉTAT PORTAIL OPEN-A OPEN-B STOP SÉCURITÉS OUVERTURE SÉCURITÉS FERMETURE SÉCURITÉ OUV/FERM W.L.
Aucun effet Aucun effet Aucun effet Aucun effet éteinte
FERMÉ Ouvre les vantaux ou le vantail Aucun effet
(OPEN-A inhibé) (OPEN-A inhibé) (OPEN-B inhibé) (OPEN-A inhibé)
J6 J6
J3 J1 J5
J5
J4
22 23 24 25
J3
J4 J1
1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
FCC 2
FCA1
FCC 1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
Fig. 1
4. CONEXIONES ELÉCTRICAS
J6
J5
J3 22 23 24 25
J4 J1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
FCC1
FCC2
FCA1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
BLU
BLU
C1 C2
M1 M2 230 VAC
max.60W 24 Vdc
3W
230 VAC
50 Hz
25
ESPAÑOL
4.1. Conexión fotocélulas y dispositivos de seguridad Dispositivos de seguridad en apertura/cierre: intervienen durante
Antes de conectar las fotocélulas (u otros dispositivos) es los movimientos de apertura y cierre de la cancela, por
conveniente elegir el tipo de funcionamiento en base a la lo tanto son adecuados para proteger la zona de apertura
zona de movimiento que deben proteger (véase fig. 3): y la de cierre contra el riesgo de impacto.
Dispositivos de seguridad en apertura: intervienen sólo durante Se aconseja el uso del esquema de la fig.4 (en caso de obstáculos
el movimiento de apertura de la cancela, por lo tanto son fijos en apertura) o del esquema de la fig.5 (cuando no hay
adecuados para proteger las zonas entre las hojas en obstáculos fijos).
apertura y obstáculos fijos (paredes, etc.) contra los
riesgos de impacto y aplastamiento. NOTA: Si dos o varios dispositivos tienen la misma función
Dispositivos de seguridad en cierre: intervienen sólo durante el (apertura o cierre) deben conectarse en serie entre sí (véase
movimiento de cierre de la cancela, por lo tanto son fig.12). Deben utilizarse contactos N.C.
adecuados para proteger la zona de cierre contra el Conexión de una pareja de fotocélulas en cierre y otra en
riesgo de impacto. apertura/cierre (esquema aconsejado)
Dispositivos de seguridad 9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
en apertura/cierre OPEN FSW +24V FSW W.L.
RX CL TX CL
1
2
- 1
3
+ 2
4 -
5 +
9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
1 OPEN FSW +24V FSW W.L.
2
1
3 Fig. 7
2
4
RX OP TX OP
1
2 RX TX
- 1 1
3
+ 2 2
4 - - 1
3
5 + + 2
4 -
5 +
Fig. 4
Fig. 8
26
ESPAÑOL
Conexión de una pareja de fotocélulas en apertura y otra 4.2. Regleta de bornes J3 - Alimentación (fig. 2)
en cierre
PE: Conexión de tierra
9 10 11 12 13 14 15 16 17 18 19 20 21 N : Alimentación 230 V~ ( Neutro )
A B STP CL OP - - - + + -TX LOCK L : Alimentación 230 V~ ( Línea )
OPEN FSW +24V FSW W.L.
Nota: Para un correcto funcionamiento es obligatoria la
conexión de la tarjeta al conductor de tierra presente en la
instalación. Coloquen línea arriba del sistema un adecuado
RX OP TX OP interruptor magnetotérmico diferencial.
1
4.3. Regleta de bornes J4 - Motores y destellador (fig. 2)
2
- 1 M1 : COM / OP / CL: Conexión Motor 1
3
+ 2 Puede utilizarse en la aplicación hoja simple
4 - M2 : COM / OP / CL: Conexión Motor 2
5 + No puede utilizarse en la aplicación hoja simple
LAMP : Salida destellador ( 230 V ~)
4.4. Regleta de bornes J1 - Accesorios (fig. 2)
OPEN A - Mando de "Apertura Total" (N.A.): se entiende cualquier
TX CL RX CL
emisor de impulso (pulsador, detector, etc.) que, al cerrarse
1
un contacto, manda la apertura y/o cierre de ambas
2
1 - hojas de la cancela.
3 Para instalar varios emisores de impulso de apertura total,
2 +
- 4 conecten los contactos N.A. en paralelo (véase fig.13).
+ 5 OPEN B - Mando de "Apertura Parcial" (N.A.) / Cierre: se
entiende cualquier emisor de impulso (pulsador, detector,
etc.) que, al cerrarse un contacto, manda la apertura y/
o cierre de la hoja mandada por el motor M1. En las lógicas
Fig. 10 B y C manda siempre el cierre de ambas hojas.
Para instalar varios emisores de impulso de apertura parcial,
Conexión de dos parejas de fotocélulas en cierre
conecten los contactos N.A. en paralelo (véase fig.13).
9 10 11 12 13 14 15 16 17 18 19 20 21 STP - Contacto de STOP (N.C.): se entiende cualquier dispositivo
A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L. (p. ej.: pulsador) que, al abrir un contacto, puede detener
el movimiento de la cancela.
Para instalar varios dispositivos de STOP conecten los
contactos N.C. en serie (véase fig.12).
RX CL1 TX CL1 Nota: Si no se conectan dispositivos de STOP, puenteen los
1 bornes STP y -.
2
- 1 CL FSW - Contacto dispositivos de seguridad en cierre (N.C.): La
3 función de los dispositivos de seguridad en cierre es la de
+ 2
4 - proteger la zona interesada por el movimiento de las hojas
+ durante la fase de cierre. En las lógicas A-SP-E-EP, durante
5
la fase de cierre, los dispositivos de seguridad invierten el
movimiento de las hojas de la cancela, o bien detienen e
invierten el movimiento cuando se liberan (véase
TX CL2 RX CL2 programación microinterruptor DS2-SW2). En las lógicas B y
1 C, durante el ciclo de cierre interrumpen el movimiento. No
2 intervienen nunca durante el ciclo de apertura. Los dispositivos
1 de seguridad de cierre, si están ocupados con la cancela
3
2 abierta, impiden el movimiento de cierre de las hojas.
4
Nota: Si no se conectan dispositivos de seguridad en cierre,
5 puenteen los bornes CL y -TX FSW (fig. 7).
Fig. 11
27
ESPAÑOL
OP FSW - Contacto dispositivos de seguridad en apertura (N.C.): 4.7. Regleta de bornes J6- Fines de carrera y/o encoder(fig. 2)
La función de los dispositivos de seguridad en apertura es la Estas entradas están predispuestas para la conexión de fines de
de proteger la zona interesada por el movimiento de las hojas carrera de apertura y de cierre que pueden mandar, según el tipo
durante la fase de apertura. En las lógicas A-SP-E-EP, durante de programación, la parada de la hoja o bien el inicio de la
la fase de apertura, los dispositivos de seguridad detienen el ralentización. Hay que puentear los fines de carrera no conectados
movimiento de las hojas de la cancela y, cuando se liberen, (si no se conecta ninguno, no es necesario).
invierten el movimiento. En las lógicas B y C, durante el ciclo Asimismo se pueden utilizar los encoders para detectar la posición
de apertura interrumpen el movimiento.Nunca intervienen angular de la hoja y por lo tanto tener posiciones de ralentización y
durante el ciclo de cierre. de parada independientes del tiempo de trabajo.
Los dispositivos de seguridad de apertura, si están ocupados Los fines de carrera y los encoders también pueden utilizarse asociados
con la cancela cerrada, impiden el movimiento de apertura para detener el movimiento antes de que se alcance el tope
de las hojas. mecánico. Para efectuar los cableados, sigan las fig.17a, 17b y 17c.
Nota: Si no se conectan dispositivos de seguridad en apertura, FCA1 - Fin de carrera de apertura Hoja 1
puenteen las entradas OP y -TX FSW (fig. 7). FCC1 - Fin de carrera de cierre Hoja 1
– - Negativo alimentación accesorios FCA2 - Fin de carrera de apertura Hoja 2
FCC1
FCC2
FCA1
eventualmente utilizar la función FAIL SAFE (véase
FCA2
- - - + + -TX LOCK
programación microinterruptor DS2-SW3). +24V FSW W.L.
Si se habilita la función, el equipo verifica el funcionamiento
de las fotocélulas antes de cada ciclo de apertura o cierre.
4.5. Regleta de bornes J5 - Luz testigo y Electrocerradura (fig. 2)
W.L. - Alimentación luz testigo
Conecten entre este borne y el +24V una eventual luz
testigo de 24 Vdc - 3 W máx. Para no perjudicar el correcto
funcionamiento del sistema, no hay que superar la
Fig. 17b
potencia indicada.
LOCK - Alimentación electrocerradura
Conecten entre este borne y el +24V una eventual
electrocerradura 12 V ac.
4.6. Conector J2 - Conector rápido 5 pins
Se utiliza para la conexión rápida. Acoplen el accesorio con el
lado componentes dirigido hacia el interior de la tarjeta. La
activación y la desactivación deben efectuarse después de
haber quitado la tensión. ROJO
BLANCO
ENCODER 1
NEGRO
ROJO
BLANCO
ENCODER 2
NEGRO
Fig. 17c
ROJO
ENCODER 1 BLANCO
NEGRO
ROJO
BLANCO
ENCODER 2
NEGRO
RP
NOTA: Las configuraciones indicadas en los dibujos son las
JA592 máximas. Se permiten todas las configuraciones
Fig. 16 intermedias, utilizando sólo algunos elementos (sólo 1
encoder, sólo 1 fin de carrera, 2 encoders y 2 fines de
carrera, etc.).
28
ESPAÑOL
FUERZA HOJA 1 SW1 SW2 SW3 FUERZA HOJA 2 SW4 SW5 SW6
RETARDO DE LA HOJA EN APERTURA (s) SW1
1 (MIN) ON ON ON 1 (MIN) ON ON ON
2 OFF ON ON 2 OFF ON ON 2 ON
3 ON OFF ON 3 ON OFF ON
0 OFF
4 OFF OFF ON 4 OFF OFF ON
5 ON ON OFF 5 ON ON OFF
6 OFF ON OFF 6 OFF ON OFF
7 7 LÓGICA FOTOCÉLULAS CIERRE SW2
ON OFF OFF ON OFF OFF
8 (MAX) OFF OFF OFF 8 (MAX) OFF OFF OFF
INVIERTE AL LIBERARSE ON
DS1 1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4
DS2
LÓGICA PAUSA (s) SW7 SW8 SW9 SW10
E / ON ON ON ON
EP / OFF ON ON ON
B / ON OFF ON ON
FAIL SAFE SW3
C / OFF OFF ON ON
A 0 ON ON OFF ON RETARDO DE LA ON
SÍ
A 10 OFF ON OFF ON SW11 SW12
HOJA EN CIERRE (s)
A 20 ON OFF OFF ON NO OFF
20 ON ON
A 30 OFF OFF OFF ON
10 OFF ON
A 60 ON ON ON OFF 5 ON OFF
GOLPE DE INVERSIÓN
A 120 OFF ON ON OFF 0 OFF OFF SW4
+ GOLPE DE ARIES
SP 0 ON OFF ON OFF
SP 10 OFF OFF ON OFF SÍ ON
SP 20 ON ON OFF OFF
NO OFF
SP 30 OFF ON OFF OFF
SP 60 ON OFF OFF OFF
Fig. 18 SP 120 OFF OFF OFF OFF Fig. 19
El equipo está provisto de dos grupos de microinterruptores DS1 (fig. el equipo efectúa una comprobación de las fotocélulas antes de
18) y DS2 (fig.19) que permiten programar los parámetros de cada movimiento de apertura y cierre.
funcionamiento de la cancela. Golpe de inversión + golpe de aries
Con el microinterruptor SW4 se pueden activar el "golpe de inversión"
5.1. MICROINTERRUPTORES DS1 (fig.18) y el "golpe de aries". El "golpe de inversión" empuja durante algunos
Fuerza Hoja 1 y 2 instantes las hojas en cierre antes de efectuar la apertura de la
Mediante los microinterruptores SW1, SW2 y SW3 se puede programar cancela, facilitando el desenganche de la electrocerradura. El
la fuerza (y por lo tanto la seguridad antiaplastamiento) del "golpe de aries" manda un empuje en cierre a plena potencia
accionador conectado a la hoja 1. La misma operación deberá cuando la cancela ya ha alcanzado el tope, facilitando así el
efectuarse para el motor conectado a la hoja 2, mediante los enganche de la electrocerradura.
microinterruptores SW4, SW5 y SW6.
Lógica de funcionamiento
Con los microinterruptores SW7, SW8, SW9 y SW10 se puede elegir la
lógica de funcionamiento de la automación. Seleccionando una 6. PUESTA EN FUNCIONAMIENTO
lógica automática (A, SP), la combinación de los microinterruptores
permite escoger también el tiempo de pausa (tiempo de espera, en
6.1. COMPROBACIÓN DE LOS LED
posición abierta, antes del sucesivo cierre automático).
Las lógicas disponibles, cuyo funcionamiento se describe en las La siguiente tabla indica el estado de los Leds en relación con el
tablas 3/a-b-c-d-e-f, son las siguientes: A - SP (Automáticas), E - EP estado de las entradas.
- B (Semiautomáticas), C (Presencia operador). Noten que: LED ENCENDIDO = contacto cerrado
LED APAGADO = contacto abierto
Retardo de la hoja en cierre
Comprueben el estado de los leds de señalización como se indica
La programación de los microinterruptores SW11 y SW12 permite
en la Tabla.
retardar el arranque en cierre de la hoja 1 respecto a la hoja 2, para
evitar la sobreposición de las hojas durante el movimiento y aumentar Funcionamiento de los leds de señalización del estado
por consiguiente la seguridad de la instalación. LEDS ENCENDIDO APAGADO
OP_A Mando activado Mando inactivo
OP_B Mando activado Mando inactivo
5.2. MICROINTERRUPTORES DS2 (fig.19) STOP Mando inactivo Mando activado
FSWCL Disp. de seguridad libres Disp. de seguridad ocupados
Retardo de la hoja en apertura FSWOP Disp. de seguridad libres Disp. de seguridad ocupados
La programación del microinterruptor SW1 permite retardar el FCA1 (si se usara) Fin de carrera libre Fin de carrera ocupado
arranque en apertura de la hoja 2 respecto a la hoja 1, para evitar FCC1 (si se usara) Fin de carrera libre Fin de carrera ocupado
que las hojas se obstaculicen entre sí durante la fase inicial del FCC2 (si se usara) Fin de carrera libre Fin de carrera ocupado
movimiento.
FCA2 (si se usara) Fin de carrera libre Fin de carrera ocupado
Lógica fotocélulas en cierre
Con el microinterruptor SW2 se puede elegir el tipo de comportamiento Nota: En negrita la condición de los leds con la cancela en reposo.
de la automación en caso de que se ocupen las fotocélulas que Asimismo, en la tarjeta se encuentra el Led DL10 que funciona como
protegen el movimiento de cierre de la cancela. Se puede obtener se indica en la siguiente tabla:
la inversión inmediata de las hojas o bien la parada con inversión
DL10
cuando se liberan las fotocélulas.
Cancela cerrada en Cancela en movimiento Aprendizaje tiempos:
Fail safe reposo: o pausa: destella rápidamente
La programación del microinterruptor SW3 permite activar o apagado como luz testigo
desactivar el test de control de las fotocélulas. Con el Fail safe activo,
29
ESPAÑOL
6.2. COMPROBACIÓN DEL SENTIDO DE ROTACIÓN Y DE LA FUERZA •En caso de uso en cancelas de edificios, para
1) Programen las funciones del equipo electrónico según las garantizar la repetibilidad de la deceleración hay
propias exigencias, como indicado en el Cap.5. que utilizar los fines de carrera o el encoder, puesto que
2) Quiten la alimentación al equipo electrónico de mando. en caso contrario la hoja puede no llegar hasta el tope
3) Desbloqueen los accionadores y coloquen manualmente la con la deceleración
cancela en la línea de centro del ángulo de apertura. •Si en fase de cierre / apertura se interrumpe el ciclo varias
4) Bloqueen de nuevo los accionadores. veces consecutivamente, la hoja no podría llegar hasta
5) Restablezcan la tensión de alimentación. el tope con la deceleración. Cuando se realice el primer
6) Envíen un mando de apertura a la entrada OPEN A (fig. 2) y ciclo completo sin interrupciones, el sistema reconocerá
comprueben que se mande una apertura de las hojas de la los topes y realizará de nuevo las deceleraciones
cancela. programadas.
NOTA: Si el primer impulso de OPEN A manda un cierre, hay que 6.3.2. APRENDIZAJE CON FINES DE CARRERA
quitar la tensión e invertir en la regleta de bornes las fases
El aprendizaje con fines de carrera puede efectuarse de dos modos
del motor eléctrico (cables marrón y negro).
diferentes:
7) Comprueben la regulación de la fuerza en los motores y si fuera
- APRENDIZAJE SIMPLE:
necesario modifíquenla (véase Cap.5.1.).
Comprueben que las hojas estén cerradas, seguidamente presionen
NOTA: Si se utilizan accionadores oleodinámicos, la fuerza debe durante 1 segundo el pulsador F: el led DL10 inicia a destellar y las
programarse al nivel máximo (8). hojas inician el movimiento de apertura.
8) Detengan el movimiento de las hojas con un mando de STOP. Los motores se detienen automáticamente cuando se alcanzan
9) Desbloqueen los accionadores, cierren las hojas y bloqueen los fines de carrera de apertura, pero es necesario dar un impulso
de nuevo los accionadores. de OPEN A (con el radiomando o con el pulsador de llave) para
terminar el ciclo; las hojas se detienen y el led DL10 deja de destellar.
6.3. APRENDIZAJE DE LOS TIEMPOS DE FUNCIONAMIENTO El procedimiento ha terminado y la cancela está lista para
funcionar.
ATENCIÓN: durante el procedimiento de aprendizaje, los dispositivos
de seguridad están desactivados! Por lo tanto, realicien la operción - APRENDIZAJE COMPLETO:
evitando cualquier tránsito en la zona de movimiento de las hojas. Comprueben que las hojas estén cerradas, seguidamente presionen
durante más de 3 segundos el pulsador F: el led DL10 inicia a destellar
El tiempo de apertura/cierre está determinado por un y la hoja 1 inicia el movimiento de apertura. Las hojas deceleran
procedimiento de aprendizaje que varía ligeramente si se utilizan automáticamente cuando se alcanzan los fines de carrera, por lo
los fines de carrera. tanto es suficiente informar al equipo, mediante impulsos de OPEN
A (con radiomando o con pulsador de llave), de que se han
6.3.1. APRENDIZAJE NORMAL TIEMPOS alcanzado los topes:
El aprendizaje normal (es decir, sin fines de carrera) puede efectuarse FCA1 - Ralentización en apertura hoja 1
de dos modos diferentes: 1° OPEN - Parada en apertura hoja 1 e inicio movimiento de
- APRENDIZAJE SIMPLE: apertura hoja 2
Comprueben que las hojas estén cerradas, seguidamente presionen FCA2 - Ralentización en apertura hoja 2
durante 1 segundo el pulsador F: el led DL10 inicia a destellar y las 2° OPEN - Parada en apertura hoja 2 e inicio inmediato del
hojas inician el movimiento de apertura. movimiento de cierre hoja 2
Esperen a que las hojas lleguen hasta el tope de apertura y FCC2 - Ralentización en cierre hoja 2
seguidamente den un impulso de OPEN A (con el radiomando o con 3° OPEN - Parada en cierre hoja 2 e inicio movimiento de
el pulsador de llave) para detener el movimiento: las hojas se cierre hoja 1
detienen y el led DL10 deja de destellar. FCC1 - Ralentización en cierre hoja 1
El procedimiento ha finalizado y la cancela está lista para funcionar. 4° OPEN - Parada en cierre hoja 1
El led DL10 deja de destellar y la cancela está lista para el
- APRENDIZAJE COMPLETO:
funcionamiento normal.
Comprueben que las hojas estén cerradas, seguidamente presionen
durante más de 3 segundos el pulsador F: el led DL10 inicia a destellar Notas: •Si se desea eliminar la ralentización en algunas fases, hay
y la hoja 1 empieza el movimiento de apertura. Mediante impulsos que dar un impulso de Open dentro de 1 s. a partir de
de OPEN A (con el radiomando o con el pulsador de llave) se que se alcancen los fines de carrera.
mandan las siguientes funciones: •Si algunos fines de carrera no están instalados, hagan
1° OPEN - Ralentización en apertura hoja 1 iniciar la ralentización correspondiente con un impulso
de Open (que sustituye al fin de carrera).
2° OPEN - Parada en apertura hoja 1 e inicio movimiento de
apertura hoja 2 •Si sólo está presente una hoja, hay que realizar
igualmente toda la secuencia. Cuando termina la
3° OPEN - Ralentización en apertura hoja 2
apertura de la hoja hay que dar 5 impulsos de Open
4° OPEN - Parada en apertura hoja 2 e inicio inmediato del hasta que la hoja empiece a cerrarse, y seguidamente
movimiento de cierre hoja 2 se sigue con el normal procedimiento.
5° OPEN - Ralentización en cierre hoja 2 6.3.3. APRENDIZAJE TIEMPOS CON ENCODER
6° OPEN - Parada en cierre hoja 2 e inicio movimiento de El aprendizaje con encoder puede efectuarse de dos modos
cierre hoja 1 diferentes:
- APRENDIZAJE SIMPLE:
7° OPEN - Ralentización en cierre hoja 1
Comprueben que las hojas estén cerradas, seguidamente presionen
8° OPEN - Parada en cierre hoja 1 durante 1 segundo el pulsador F: el led DL10 inicia a destellar y las
El led DL10 deja de destellar y la cancela está lista para funcionar hojas inician el movimiento de apertura.
normalmente. El movimiento se detiene automáticamente cuando se alcanza el
tope de apertura y el led DL10 deja de destellar.
Notas: •Si se desea eliminar la ralentización en algunas fases, hay El procedimiento ha terminado y la cancela está lista para funcionar
que esperar a que la hoja llegue hasta el tope y dar dos utilizando una ralentización fija.
impulsos de Open consecutivos (antes de 1 segundo). - APRENDIZAJE COMPLETO:
•Si sólo está presente una hoja, hay que realizar igualmente Comprueben que las hojas estén cerradas, seguidamente presionen
toda la secuencia. Cuando termina la apertura de la durante más de 3 segundos el pulsador F: el led DL10 inicia a destellar
hoja hay que dar 5 impulsos de Open hasta que la hoja y la hoja 1 inicia el movimiento de apertura.
empiece a cerrarse, y seguidamente se sigue con el
normal procedimiento.
30
ESPAÑOL
encendida
encendida
encendida
destellante
encendida
encendida
encendida
destellante
apagada
apagada
1° OPEN - Ralentización en apertura hoja 1 (se detiene
W.L.
W.L.
automáticamente cuando se alcanza el tope)
2° OPEN - Inicio movimiento de apertura hoja 2
3° OPEN - Ralentización en apertura hoja 2 (se detiene
automáticamente cuando se alcanza el tope)
Bloqueaycuandoseliberacontinúa
Bloqueaycuandoseliberainvierteen
Bloqueaycuandoseliberacontinúa
4° OPEN - Inicio movimiento de cierre hoja 2
Ningúnefecto(OPENinhibido)
DISP. SEGURIDAD AP/CI
Ningúnefecto(OPENinhibido)
5° OPEN - Ralentización en cierre hoja 2 (se detiene
apertura
abriendo
abriendo
apertura
Congelalapausahastalaliberación(2)(OPENinhibido)
7° OPEN - Ralentización en cierre hoja 1 (se detiene
automáticamente cuando se alcanza el tope)
Cierradespuésde5"(OPENinhibido)
El led DL10 deja de destellar y la cancela está lista para el
Ningúnefecto(OPENinhibido)
Ningúnefecto(OPENinhibido)
funcionamiento normal.
Notas: •El impulso de ralentización debe darse con un cierto
adelanto respecto al tope, para evitar que la hoja llegue
a plena velocidad (sería interpretado como obstáculo).
•Si sólo está presente una hoja, hay que realizar
DIS.SEGURIDAD CIERRE
DIS.SEGURIDAD CIERRE
igualmente toda la secuencia. Cuando termina la
Véasepárrafo5.2.
Véasepárrafo5.2.
Ningúnefecto
Ningúnefecto
apertura de la hoja hay que dar 5 impulsos de Open
Ningúnefecto
Ningúnefecto
hasta que la hoja empiece a cerrarse, y seguidamente
se sigue con el normal procedimiento.
•Para un correcto funcionamiento es indispensable
tener el tope mecánico en apertura y en cierre.
DIS.SEGURIDAD APERTURA
Ningúnefecto(memorizaOPEN)
DIS.SEGURIDAD APERTURA
Ningúnefecto(memorizaOPEN)
- APRENDIZAJE SIMPLE:
Efectúen el mismo procedimiento descrito para el aprendizaje con
Invierte en cierre
Invierte en cierre
Ningúnefecto
Ningúnefecto
IMPULSOS
Ningúnefecto
Ningúnefecto
IMPULSOS
Ningúnefecto(OPENinhibido)
Efectúen el mismo procedimiento descrito para el aprendizaje con
Ningúnefecto(OPENinhibido)
Ningúnefecto(OPENinhibido)
Ningúnefecto(OPENinhibido)
funcionamiento
funcionamiento
Bloqueael
hasta que la hoja empiece a cerrarse, y seguidamente
Bloqueael
STOP
STOP
Bloquea el funcionamiento
Recargaeltiempodepausa(1)
Abredenuevolahoja
Abre de nuevo la hoja
inmediatamente
inmediatamente(1)
inmediatamente
Cierrala/shoja/s
Bloquea el funcionamiento
Recargaeltiempodepausa(1)
inmediatamente
inmediatamente(1)
tiempodepausa
inmediatamente
7. PRUEBA DE LA AUTOMACIÓN
ABIERTA en PAUSA
ABIERTA en PAUSA
ESTADO CANCELA
ESTADO CANCELA
EN APERTURA
BLOQUEADA
EN APERTURA
BLOQUEADA
EN CIERRE
EN CIERRE
funcione correctamente.
LÓGICA "SP"
LÓGICA "A"
Tab. 3/b
31
Tab. 3/c
LÓGICA "E" IMPULSOS
ESTADO CANCELA OPEN-A OPEN-B STOP DIS.SEGURIDAD APERTURA DIS.SEGURIDAD CIERRE DISP. SEGURIDAD AP/CI W.L.
EN CIERRE Abredenuevolashojas Abre de nuevo la hoja Bloqueael Ningúnefecto(memorizaOPEN) Véasepárrafo5.2. Bloqueaycuandoseliberainvierteen destellante
inmediatamente inmediatamente funcionamiento apertura
Tab. 3/d
LÓGICA "EP" IMPULSOS
ESTADO CANCELA OPEN-A OPEN-B STOP DIS.SEGURIDAD APERTURA DIS.SEGURIDAD CIERRE DISP. SEGURIDAD AP/CI W.L.
CERRADA Abre las hojas Abre la hoja libre Ningún efecto (OPEN inhibido) Ningún efecto Ningún efecto (OPEN inhibido) apagada
ABIERTA Cierra de nuevo la/s hoja/s inmediatamente Ningún efecto (OPEN inhibido) Ningún efecto (OPEN inhibido) encendida
EN CIERRE Bloquea el funcionamiento Ningún efecto (memoriza OPEN) Véase párrafo 5.2. Bloquea y cuando se libera invierte en destellante
Bloquea el
funcionamiento apertura
EN APERTURA Bloquea el funcionamiento Invierte en cierre Ningún efecto Bloquea y cuando se libera continúa encendida
abriendo
32
Tab. 3/e
LÓGICA "B" IMPULSOS
ESTADO CANCELA OPEN-A OPEN-B STOP DIS.SEGURIDAD APERTURA DIS.SEGURIDAD CIERRE DISP. SEGURIDAD AP/CI W.L.
Ningún efecto Ningún efecto Ningún efecto Ningún efecto apagada
CERRADA Abre las hojas o la hoja Ningún efecto (OPEN-A inhibido) (OPEN-A inhibido) (OPEN-A inhibido)
(OPEN-B inhibido)
Tab. 3/f
LÓGICA "C" COMANDI SEMPRE PREMUTI IMPULSOS
ESTADO CANCELA OPEN-A OPEN-B STOP DIS.SEGURIDAD APERTURA DIS.SEGURIDAD CIERRE DISP. SEGURIDAD AP/CI W.L.
Ningún efecto Ningún efecto Ningún efecto Ningún efecto apagada
CERRADA Abre las hojas o la hoja Ningún efecto
(OPEN-A inhibido) (OPEN-A inhibido) (OPEN-B inhibido) (OPEN-A inhibido)
- Das Erdungskabel ist an die entsprechende Klemme auf dem Stecker J3 F DL10
FCC 2
FCA1
FCC 1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
2. TECHNISCHE EIGENSCHAFTEN
Abb. 1
Versorgungsspannung 230 V~ ( +6% -10%) - 50 Hz
Leistungsverbrauch 10 W Led OP_A LED-DIODE OPEN VOLLSTÄNDIG
Max. Last Motor 800 W Led OP_B LED-DIODE OPEN FLÜGEL 1 / CLOSE
Max. Last Zubehör 0,5 A Led STOP LED-DIODE STOP
Max. Last Elektroschloß 15 VA Led FSWCL LED-DIODE SICHERHEITSVORRICHTUNGEN BEIMSCHLIESSVORGANG
Temperatur am Aufstellungsort -20 °C +55 °C
Led FSWOP LED-DIODESICHERHEITSVORRICHTUNGENBEIMOFFNUNGSVORGANG
Sicherungen Nr. 2 (siehe Abb. 1)
Led FCC1 LED-DIODE ENDSCHALTER ÖFFNUNGSVORGANG FLÜGEL 1
BetriebssteuerungenAutomatik / Halbautomatik / Sicherheit "Schrittbetrieb" / Halbautomatik B
/ Totmann C / Halbautomatik "Schrittbetrieb" Led FCA1 LED-DIODE ENDSCHALTER SCHLIEßVORGANG FLÜGEL 1
Zeit Öffnungs-/Schließvorgang programmierbar (zwischen 0 und 120 s) Led FCC2 LED-DIODE ENDSCHALTER ÖFFNUNGSVORGANG FLÜGEL 2
Pausenzeit 0, 10, 20, 30, 60, 120 s Led FCA2 LED-DIODE ENDSCHALTER SCHLIEßVORGANG FLÜGEL 2
VerzögerungszeitdesFlügelsbeimSchließvorgang 0, 5, 10, 20 s DL10 LED-DIODE ANZEIGE LERNVERFAHREN ZEITEN
VerzögerungszeitdesFlügelsbeimÖffnungsvorgang 2 s (über Dip-Schalter ausschaltbar)
J1 KLEMMENLEISTE NIEDERSPANNUNG
Schubkraft über Dip-Schalter auf 8 Stufen für jeden Motor regulierbar
J2 SCHNELLSTECKER 5 PINS
Eingänge in Klemmenleiste Open / Open Flügel frei / Stop /
J3 KLEMMENLEISTE VERSORGUNG 230 VAC
Endschalter / Sicherheitsvorrichtung für Öffnungsvorgang /
Sicherheitsvorrichtung für Schließvorgang / Versorgung+Erdung J4 KLEMMENLEISTE ANSCHLUSS MOTOREN UND BLINKLEUCHTE
Ausgänge aus Klemmenleiste Blinkleuchte - Motoren - Versorgung Zubehör 24 Vdc J5 KLEMMENLEISTE KONTROLLAMPE UND ELEKTROSCHLOß
- Kontrollampe 24 Vdc - Failsafe - Versorgung Elektroschloß 12 Vac J6 KLEMMENLEISTE ENDSCHALTER UND ENCODER
Schnellstecker Schnellstecker 5 pins F1 SICHERUNGENMOTORENUNDPRIMÄRWICKLUNGTRANSFORMATOR(F5A)
Anwählbare Funktionen Steuerungen und Pausenzeiten - Schubkraft- F2 SICHERUNGEN NIEDERSPANNUNG UND ZUBEHÖR (T 800MA)
Verzögerung des Flügels beim Öffnungs- und Schließvorgang - Umkehrstoß-
Failsafe - Steuerung Sicherheitsvorrichtungen beim Schließvorgang - Vorblinken F TASTE ANWAHL LERNVERFAHREN ZEITEN
Programmierungstaste Einfaches oder vollständiges Lernverfahren der DS1 1. GRUPPE MIKROSCHALTER PROGRAMMIERUNG
Arbeitszeiten mit oder ohne Endschalter und/oder encoder DS2 2. GRUPPE MIKROSCHALTER PROGRAMMIERUNG
4. ELEKTRISCHE ANSCHLÜSSE
J6
J5
J3 22 23 24 25
J4 J1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
FCC1
FCC2
FCA1
FCA2
PE N L OP
COM M1
OP
COM M2 CL LAMP
A B STP CL OP - - - + + -TX LOCK
MAIN OPEN FSW +24V FSW W.L.
BLAU
BLAU
C1 C2
M1 M2 230 VAC
max.60W 24 Vdc
3W
230 VAC
50 Hz
Hinsichtlich des
ACHTUNG: Beachten Sie Anschlusses der
die Folge Phase/Nullleiter OPEN VOLLSTÄNDIG Photozellen und der
beim Anschluss. Sicherheitsvorrichtungen 12 V ac
OPEN FLÜGEL 1 ist auf den
Abschnitt 4.1.
ENDSCHALTER
STOP Bezug zu nehmen.
Anmerkung: die Kondensatoren werden gemeinsam mit den Antrieben geliefert. Abb. 2
33
DEUTSCH
4.1. Anschluß der Photozellen und der Sicherheitsvorrichtungen Sicherheitsvorrichtungen beim Öffnungs-/Schließvorgang: diese
Vorrichtungen greifen während der Öffnungsbewegung und
Vor dem Anschluß der Photozellen (oder anderen Vorrichtungen) sollte die während der Schließbewegung des Tors ein und eignen sich
Betriebsart entsprechend des Bewegungsbereiches, den diese daher sowohl für den Schutz des Öffnungsbereichs wie des
überwachen oder schützen sollen, ausgewählt werden (siehe Abb. 3): Schließbereichs vor Aufschlägen.
Sicherheitsvorrichtungen beim Öffnungsvorgang: diese Vorrichtungen Man empfiehlt die Verwendung des Anschlußplans der Abb.4 (im Falle von
greifen lediglich während der Öffnungsbewegung des Tors ein, feststehenden Hindernissen beim Öffnungsvorgang) oder des
sie eignen sich daher für den Schutz der Bereiche zwischen den Anschlußplans der Abb.5 (Kein Vorhandensein von feststehenden
Flügeln beim Öffnungsvorgang und feststehenden Hindernissen Hindernissen).
(Wänden, usw.) vor Aufschlag und Quetschungen.
Anmerkung: sollten zwei oder mehrere Vorrichtungen die gleiche Funktion
Sicherheitsvorrichtungen beim Schließvorgang: diese Vorrichtungen greifen ausüben (Öffnungs- oder Schließvorgang), so sind diese in Reihenschaltung
lediglich während der Schließbewegung des Tors ein, sie eignen untereinander anzuschließen (siehe Abb. 12). Dabei sind Arbeitskontakte zu
sich daher für den Schutz des Schließbereichs vor Aufschlägen. verwenden.
RX CL TX CL
1
2
- 1
3
+ 2
4 -
5 +
Sicherheitsvorrichtungen beim
Sicherheitsvorrichtungen
Schließvorgang
beim Öffnungsvorgang 1
Abb. 3
2
1
3
Anschluß eines Photozellenpaars beim Schließvorgang, eines Paars 2
beim Öffnungsvorgang sowie eines Paars beim Öffnungs-/ 4
Schließvorgang (empfohlener Anschlußplan)
5
9 10 11 12 13 14 15 16 17 18 19 20 21 TX OP/CL RX OP/CL
A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L. Abb. 5
RX CL TX CL 9 10 11 12 13 14 15 16 17 18 19 20 21
1 A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
2
- 1
3
+ 2 Abb. 6
4 -
5 + Kein Anschluß einer Sicherheitsvorrichtung
9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
1
2
1
3 Abb. 7
2
4
Anschluß 1 Photozellenpaars beim Öffnungsvorgang
5
TX OP/CL RX OP/CL 9 10 11 12 13 14 15 16 17 18 19 20 21
A B STP CL OP - - - + + -TX LOCK
OPEN FSW +24V FSW W.L.
RX OP TX OP
1
RX TX
2 1
- 1
3 2
+ 2 - 1
4 - 3
+ + 2
5 4 -
5 +
Abb. 4
Abb. 8
34
DEUTSCH
Abb. 11
35
DEUTSCH
OP FSW - Kontakt Sicherheitsvorrichtungen beim Öffnungsvorgang 4.7. Klemmenleiste J6- Endschalter und/oder encoder(Abb. 2)
(Arbeitskontakt): Die Funktion der Sicherheitsvorrichtungen beim
Öffnungsvorgang liegt im Schutz des Bereichs, der von der Diese Eingänge sind für den Anschluß der Endschalter für den Öffnungs-
Bewegung der Flügel in der Öffnungsphase betroffen ist. In den und den Schließvorgang ausgelegt, die je nach Programmierung den
Steuerungsarten A-SP-E-EP halten die Sicherheitsvorrichtungen Stopp des Flügel oder den Beginn der Abbremsung steuern. Die nicht
während der Öffnungsphase die Bewegung der Flügel des Tors angeschlossenen Endschalter müssen mit Überbrückungsklemmen
an und steuern die Bewegungsumkehr bei Freiwerden der versehen werden (werden keine Endschalter angeschlossen, so ist dies
Sicherheitsvorrichtungen. In den Steuerungsarten B und C wird nicht erforderlich).
während des Öffnungszyklus die Bewegung unterbrochen. Diese Darüber hinaus können die encoderen eingesetzt werden, um die
Sicherheitsvorrichtungen werden nicht während des Schließzyklus jeweilige Winkelposition des Flügels zu ermitteln und damit Abbrems- und
aktiv.
Stoppositionen zu gewährleisten, die unabhängig von der Arbeitszeit sind.
Die Sicherheitsvorrichtungen beim Öffnungsvorgang verhindern,
sprechen sie bei geschlossenem Tor an, die Öffnungsbewegung Die Endschalter und die encoderen können auch gemeinsam eingesetzt
der Flügel. werden, um die Bewegung vor dem Erreichen des mechanischen
Anmerkung: werden keine Sicherheitsvorrichtungen beim Anschlags anzuhalten. Hinsichtlich der Ausführung der Verkabelung ist auf
Öffnungsvorgang angeschlossen, so sind die Klemmen OP und - die Abb.17a, 17b und 17c Bezug zu nehmen.
TX FSW mit Überbrückungsklemmen zu versehen (Abb. 7). FCA1 - Endschalter Öffnungsvorgang Flügel 1
– - Negativ Versorgung Zubehör FCC1 - Endschalter Schließvorgang Flügel 1
+ - 24 Vdc - Positiv Versorgung Zubehör FCA2 - Endschalter Öffnungsvorgang Flügel 2
Achtung: die maximale Last des Zubehörs liegt bei 500 mA. Um
den jeweiligen Verbrauch zu berechnen, ist auf die Anleitungen FCC2 - Endschalter Schließvorgang Flügel 2
der einzelnen Zubehörteile Bezug zu nehmen.
-TX FSW - Negativ Versorgung Übertragungsgeräte Photozellen
Abb. 17a J6
J5
Durch Verwendung dieser Klemme für den Anschluß des Negativs
der Versorgung der Übertragungsgeräte der Photozellen kann
eventuell die Funktion FAILSAFE verwendet werden (siehe 22 23 24 25
Programmierung Mikroschalter DS2-SW3).
Wird die Funktion aktiviert, überprüft das Gerät den störungsfreien 14 15 16 17 18 19 20 21
FCC1
FCC2
FCA1
FCA2
Betrieb der Photozellen vor der Ausführung eines jeden Zyklus zur - - - + + -TX LOCK
Öffnung oder zur Schließung. +24V FSW W.L.
4.5. Klemmenleiste J5 - Kontrollampe und Elektroschloß (Abb. 2)
W.L. - Versorgung Kontrollampe
Zwischen dieser Klemme und dem +24V eine eventuelle
Kontrollampe mit 24 Vdc - max. 3 W anschließen. Um den
störungsfreien Betrieb des Systems nicht zu beeinträchtigen, sollte
die angegebene Leistung nicht überschritten werden.
LOCK - Versorgung Elektroschloß
Zwischen dieser Klemme und dem +24V ist ein eventuelles Abb. 17b
Elektroschloß 12 V ac anzuschließen.
4.6. Stecker J2 - SCHNELLSTECKER 5 PINS
Dieser Stecker wird für den Schnellanschluß benutzt. Das Zubehör mit der
Komponentenseite zum Inneren der Karte hin einstecken. Das Einstecken
und Abziehen erfolgt lediglich nach dem abnahme der Spannung.
ROT
WEISS
SCHWARZ ENCODER 1
ROT
WEISS
ENCODER 2
SCHWARZ
Abb. 17c
ROT
WEISS
SCHWARZ ENCODER 1
ROT
WEISS
ENCODER 2
SCHWARZ
RP
36
DEUTSCH
5. MIKROSCHALTERPROGRAMMIERUNG
KRAFT FLÜGEL 1 SW1 SW2 SW3 KRAFT FLÜGEL 2 SW4 SW5 SW6
VERZÖGERUNG FLÜGEL BEIM SW1
1 (MIN) ON ON ON 1 (MIN) ON ON ON ÖFFNUNGSVORGANG (s)
2 OFF ON ON 2 OFF ON ON 2 ON
3 ON OFF ON 3 ON OFF ON
0 OFF
4 OFF OFF ON 4 OFF OFF ON
5 ON ON OFF 5 ON ON OFF
6 OFF ON OFF 6 OFF ON OFF
STEUERUNG PHOTOZELLEN SW2
7 ON OFF OFF 7 ON OFF OFF
SCHLIESSVORGANG
8 (MAX) OFF OFF OFF 8 (MAX) OFF OFF OFF
UMKEHR BEI FREIWERDEN ON
DS1 1 2 3 4 5 6 7 8 9 10 11 12
Das Gerät ist mit zwei Gruppen von Mikroschaltern ausgestattet: DS1 (Abb. Failsafe
18) und DS2 (Abb.19). Diese ermöglichen die Programmierung der Die Programmierung des Mikroschalters SW3 ermöglicht die Ein- oder
Betriebsparameter des Tors. Ausschaltung des Kontrolltests auf den Photozellen. Mit der aktivierten
Failsafe-Funktion führt das Gerät eine Überprüfung des störungsfreien
5.1. MIKROSCHALTER DS1 (Abb.18) Betriebs der Photozellen vor jeder Öffnungs- und Schließbewegung aus.
Kraft Flügel 1 und 2 Umkehrstoß + Druckstoß
Über die Mikroschalter SW1, SW2 und SW3 kann die Kraft (und damit die Mit dem Mikroschalter SW4 können der "Umkehrstoß" und der "Druckstoß"
Sicherheitseinrichtung Quetschschutz) des Antriebs, der an den Flügel 1 eingeschaltet werden. Der "Umkehrstoß" drückt die Flügel für einen Moment
angeschlossen ist, reguliert werden. Der gleiche Arbeitsvorgang ist für den in die Schließrichtung, bevor die Öffnung des Tors erfolgt, und erleichtert
Motor des Flügels 2 auszuführen, indem die Mikroschalter SW4, SW5 und SW6 damit die Öffnung des Elektroschlosses. Der "Druckstoß" steuert einen Schub
programmiert werden. in der Schließbewegung mit voller Leistung, wenn das Tor bereits den
Betriebslogik Anschlag erreicht hat, und erleichtert damit die Schließung des Elektroschlosses.
Mit den Mikroschaltern SW7, SW8, SW9 und SW10 kann die Betriebslogik der
Automation angewählt werden. Bei der Anwahl einer automatischen
Steuerung (A, SP), ermöglicht die Kombination der Mikroschalter auch die
6. INBETRIEBNAHME
Auswahl der Pausenzeit (Wartezeit in offener Position vor der erneuten
automatischen Schließung).
6.1. ÜBERPRÜFUNG DER LED-DIODEN
Die folgenden Steuerungen, deren Betrieb in den Tabellen 3/a-b-c-d-e-f Die folgende Tabelle zeigt den Status der LED-Dioden in Bezug auf den Status
beschrieben wird, stehen zur Verfügung: A - SP (Automatik), E - EP - B der Eingänge.
(Halbautomatisch), C (Totmann). Dabei ist zu berücksichtigen: LED-DIODE EIN = Kontakt geschlossen
LED-DIODE AUS = Kontakt offen
Verzögerung des Flügels beim Schließvorgang
Der Status der Hinweis-LED-Dioden ist gemäß der Angaben in der Tabelle zu
Die Programmierung der Mikroschalter SW11 und SW12 ermöglicht die
überprüfen.
Verzögerung des Beginns des Schließvorgangs des Flügels 1 gegenüber
dem Flügel 2, um ein Übereinnanderlappen der Flügel während des Betrieb der Hinweis-LED-Dioden Status
Bewegungsablaufs zu vermeiden, und damit die Sicherheit der Anlage zu
erhöhen. LED-Dioden EIN AUS
OP_A Steuerung aktiviert Steuerung nicht aktiviert
OP_B Steuerung aktiviert Steuerung nicht aktiviert
STOP Steuerung nicht aktiviert Steuerung aktiviert
FSWCL Sicherheiten frei Sicherheiten sprechen an
FSWOP Sicherheiten frei Sicherheiten sprechen an
5.2. MIKROSCHALTER DS2 (Abb.19) FCA1 (soweit eingesetzt) Endschalter frei Endschalter spricht an
Verzögerung des Flügels beim Öffnungsvorgang FCC1 (soweit eingesetzt) Endschalter frei Endschalter spricht an
Die Programmierung des Mikroschalters SW1 ermöglicht die Verzögerung FCC2 (soweit eingesetzt) Endschalter frei Endschalter spricht an
des Beginns des Öffnungsvorgangs des Flügels 2 gegenüber dem Flügel 1, FCA2 (soweit eingesetzt) Endschalter frei Endschalter spricht an
um zu vermeiden, daß sich die Flügel in der Anfangsphase des
Bewegungsablaufs gegenseitig behindern.
Anmerkung: Der Zustand der LED-Dioden bei Tor in Ruhestellung ist fettgedruckt.
Steuerung Photozellen beim Schließvorgang
Mit dem Mikroschalter SW2 kann das Verhalten der Automation in dem Falle Darüber hinaus befindet sich auf der Karte die LED-Diode DL10, deren Betrieb
angewählt werden, in dem die Photozellen abgedunkelt werden, die die aus folgender Tabelle hervorgeht:
Schließbewegung des Tors überwachen. Dabei kann die unmittelbare
Umkehr der Flügel oder aber ein Stopp mit Umkehr bei Freiwerden der DL10
Photozellen eingestellt werden. Tor geschlossen in Tor in Bewegung oder Lernverfahren Zeiten:
Ruhestellung: Pause: schnelles Blinken
aus wie Kontrollampe
37
DEUTSCH
6.2. ÜBERPRÜFUNG DER DREHRICHTUNG UND DER KRAFT oder Encoder zu verwenden, um die Wiederholbarkeit der
1) Programmierung der Funktionen des elektronischen Geräts Verlangsamung zu gewährleisten. Andernfalls erreicht der
entsprechend der jeweiligen Anforderungen unter Bezugnahme auf Flügel mit der Verlangsamung möglicherweise den Anschlag
Kap.5. nicht.
2) Abnahme der Versorgung vom elektronischen Steuergerät. •Wenn der Zyklus beim Öffnungs-/Schließvorgang mehrmals
3) Freigabe der Antriebe und manuelles Verschieben des Tors auf die hintereinander unterbrochen wird, erreicht der Flügel mit der
Mittellinie des Öffnungswinkels. Verlangsamung möglicherweise den Anschlag nicht. Beim
4) Erneute Sperre der Antriebe. ersten vollständigen unterbrechungsfreien Zyklus erkennt das
5) Wiederanlage der Versorgungsspannung. System die Anschläge und führt die programmierten
6) Übertragung eines Öffnungsbefehls auf den Eingang OPEN A (Abb. Verlangsamungen erneut aus.
2) und Überprüfung, ob eine Öffnung der Flügel des Tors gesteuert
6.3.2. LERNVERFAHREN MIT ENDSCHALTERN
werden kann.
Das Lernverfahren mit Endschaltern kann auf zwei verschiedene
Anmerkung: Sollte der erste Impuls OPEN A einen Schließvorgang steuern, Weisen ausgeführt werden:
so ist die Spannung abzunehmen und die Phasen des
Elektromotors (braunes und schwarzes Kabel) sind auf der - EINFACHES LERNVERFAHREN:
Klemmenleiste des Steuergeräts umzukehren. Überprüfen, ob die Flügel geschlossen sind, dann für einen Zeitraum von
1 Sekunde die Taste F drücken: die LED-Diode DL10 beginnt zu blinken und
7) Überprüfung der Einstellung der Kraft auf den Motoren und Ausführung
die Flügel beginnen die Öffnungsbewegung.
eventueller Veränderungen (siehe Kap.5.1.).
Die Motoren stoppen automatisch bei Erreichen der Endschalter des
Anmerkung: beim Einsatz von hydraulischen Antrieben sollte die Kraft auf Öffnungsvorganges, es ist jedoch ein Impuls OPEN A (über die Funksteuerung
der höchsten Stufe (8) eingestellt werden. oder mit der Schlüsseltaste) erforderlich, um den Zyklus abzuschließen. Die
8) Stopp der Bewegung der Flügel durch einen STOP-Befehl. Flügel halten an und die LED-Diode DL10 blinkt nicht mehr.
9) Freigabe der Antriebe, Schließung der Flügel und erneute Sperre der Das Lernverfahren ist abgeschlossen und das Tor ist für den Betrieb bereit.
Antriebe. - VOLLSTÄNDIGES LERNVERFAHREN:
Überprüfen, ob die Flügel geschlossen sind, dann für einen Zeitraum von
6.3. LERNVERFAHREN DER BETRIEBSZEITEN mehr als 3 Sekunden die Taste F drücken: die LED-Diode DL10 beginnt zu
blinken und der Flügel 1 beginnt die Öffnungsbewegung. Die Flügel
ANMERKUNG: Während des Lernverfahrens werden die Sicherheiten bremsen automatisch bei Erreichen der Endschalter ab, es ist daher
nicht aktiv! Deshalb ist während dieses Vorgangs kein Durchgang ausreichend, das Gerät über das Erreichen der Anschläge zu informieren,
im Flügelbewegungsbereich zu gestatten . indem Impulse OPEN A (über die Funksteuerung oder mit der Schlüsseltaste)
gegeben werden:
Die Zeit für den Öffnungs-/Schließvorgang wird durch ein Lernverfahren FCA1 - Abbremsung beim Öffnungsvorgang Flügel 1
festgelegt, das beim Einsatz von Endschaltern geringfügig 1. OPEN - Stopp beim Öffnungsvorgang Flügel 1 und Beginn der
unterschiedlich ist. Öffnungsbewegung Flügel 2
FCA2 - Abbremsung beim Öffnungsvorgang Flügel 2
6.3.1. NORMALES LERNVERFAHREN DER ZEITEN
2. OPEN - Stopp beim Öffnungsvorgang Flügel 2 und
Das normale Lernverfahren (d.h. ohne den Einsatz von Endschaltern ) kann unverzüglicher Beginn der Schließbewegung Flügel 2
auf zwei verschiedene Weisen ausgeführt werden: FCC2 - Abbremsung beim Schließvorgang Flügel 2
- EINFACHES LERNVERFAHREN: 3. OPEN - Stopp beim Schließvorgang Flügel 2 und Beginn der
Überprüfen, ob die Flügel geschlossen sind, dann für einen Zeitraum von 1 Schließbewegung Flügel 1
Sekunde die Taste F drücken: die LED-Diode DL10 beginnt zu blinken und die FCC1 - Abbremsung beim Schließvorgang Flügel 1
Flügel beginnen die Öffnungsbewegung. 4. OPEN - Stopp beim Schließvorgang Flügel 1
Die Ankunft der Flügel auf dem Öffnungsanschlag abwarten, dann einen Die LED-Diode DL10 hört auf zu blinken und das Tor ist für den normalen
Impuls OPEN A geben (über Funksteuerung oder Schlüsseltaste), um die Betrieb bereit.
Bewegung anzuhalten: die Flügel halten an und die LED-Diode DL10 hört auf
zu blinken. Anmerkungen: • Soll die Abbremsung in einigen Phasen ausgeschaltet
Das Verfahren ist nun abgeschlossen und das Tor ist für den Betrieb bereit. werden, so muß innerhalb einer Sekunde nach dem
Erreichen des Endschalters ein Impuls Open gegeben
- VOLLSTÄNDIGES LERNVERFAHREN: werden.
Überprüfen, ob die Flügel geschlossen sind, dann für einen Zeitraum von
mehr als 3 Sekunden die Taste F drücken: die LED-Diode DL10 beginnt zu • Sind einige Endschalter nicht installiert worden, so ist die
blinken und der Flügel 1 beginnt die Öffnungsbewegung. Durch die entsprechende Abbremsung mit einem Impuls Open zu
Impulse OPEN A (über Funksteuerung oder Schlüsseltaste) werden die beginnen (der den Endschalter ersetzt).
folgenden Funktionen gesteuert: • Ist lediglich ein Flügel vorhanden, so ist dennoch die
1. OPEN - Abbremsung beim Öffnungsvorgang Flügel 1 gesamte Abfolge auszuführen. Nach Beendigung des
Öffnungsvorganges des Flügels sind 5 Impulse Open zu
2. OPEN - Stopp beim Öffnungsvorgang Flügel 1 und Beginn der
geben, bis der Flügel beginnt, sich zu schließen. Dann ist
Öffnungsbewegung Flügel 2
die normale Vorgehensweise wieder aufzunehmen.
3. OPEN - Abbremsung beim Öffnungsvorgang Flügel 2
4. OPEN - Stopp beim Öffnungsvorgang Flügel 2 und unverzüglicher
6.3.3. LERNVERFAHREN ZEITEN MIT ENCODER
Beginn der Schließbewegung Flügel 2 Das Lernverfahren mit encoder kann auf zwei verschiedene Weisen
ausgeführt werden:
5. OPEN - Abbremsung beim Schließvorgang Flügel 2
- EINFACHES LERNVERFAHREN:
6. OPEN - Stopp beim Schließvorgang Flügel 2 und Beginn der
Überprüfen, ob die Flügel geschlossen sind, dann für einen Zeitraum von
Schließbewegung Flügel 1
1 Sekunde die Taste F drücken: die LED-Diode DL10 beginnt zu blinken und
7. OPEN - Abbremsung beim Schließvorgang Flügel 1 die Flügel beginnen die Öffnungsbewegung.
8. OPEN - Stopp beim Schließvorgang Flügel 1 Die Bewegung stoppt automatisch bei Erreichen des Öffnungsanschlages
und die LED-Diode DL10 blinkt nicht mehr.
Die LED-Diode DL10 hört auf zu blinken und das Tor ist für den normalen Betrieb Das Lernverfahren ist abgeschlossen und das Tor ist für den Betrieb unter
bereit. Einschluß einer vorbestimmten Abbremsung bereit.
Anmerkungen: •Soll die Abbremsung in einigen Phasen ausgeschaltet - VOLLSTÄNDIGES LERNVERFAHREN:
werden, so sollte abgewartet werden, bis der Flügel am Überprüfen, ob die Flügel geschlossen sind, dann für einen Zeitraum von
Anschlag ankommt. Dann sind zwei aufeinanderfolgende mehr als 3 Sekunden die Taste F drücken: die LED-Diode DL10 beginnt zu
Impulse Open zu geben (innerhalb einer Sekunde). blinken und der Flügel 1 beginnt die Öffnungsbewegung.
•Ist lediglich ein Flügel vorhanden, so ist dennoch die Uber die Impulse OPEN A (über die Funksteuerung oder mit der Schlüsseltaste)
gesamte Abfolge auszuführen. Nach Beendigung des können die folgenden Funktionen gesteuert werden:
Öffnungsvorganges des Flügels sind 5 Impulse Open zu 1. OPEN - Abbremsung beim Öffnungsvorgang Flügel 1 (dieser hält
geben, bis der Flügel beginnt, sich zu schließen. Dann ist automatisch bei Erreichen des Anschlages an)
die normale Vorgehensweise wieder aufzunehmen. 2. OPEN - Beginn der Öffnungsbewegung Flügel 2
3. OPEN - Abbremsung beim Öffnungsvorgang Flügel 2 (dieser hält
•Bei Verwendung in Mehrfamilienhäusern sind Endschalter
38
DEUTSCH
blinkt
blinkt
W.L.
aus
ein
ein
ein
aus
ein
ein
ein
W.L.
automatisch bei Erreichen des Anschlages an)
6. OPEN - Beginn der Schließbewegung Flügel 1
7. OPEN - Abbremsung beim Schließvorgang Flügel 1 (dieser hält
automatisch bei Erreichen des Anschlages an)
BlockierungundbeiFreiwerdenFortsetzungder
BlockierungundbeiFreiwerdenFortsetzungder
Blockierung und bei Freiwerden Umkehr in
Blockierung und bei Freiwerden Umkehr in
Die LED-Diode DL10 blinkt nicht mehr und das Tor ist für den normalen Betrieb
KeineAuswirkung(OPENunterdrückt)
SICHERHEITENÖFFNUNG/SCHLIESSUNG
KeineAuswirkung(OPENunterdrückt)
SICHERHEITENÖFFNUNG/SCHLIESSUNG
bereit.
Anmerkung: •Der Abbremsimpuls sollte mit einem gewissen Vorlauf
VerbleibtinPausebiszumFreiwerden(2)(OPENunterdrückt)
gegenüber dem Anschlag gegeben werden, um zu
Öffnung
Öffnung
Öffnung
Öffnung
verhindern, daß der Flügel den Anschlag mit voller
Geschwindigkeit erreicht (der Anschlag würde andernfalls
als Hindernis betrachtet).
KeineAuswirkung(OPENunterdrückt)
KeineAuswirkung(OPENunterdrückt)
Schließtnach5"(OPENunterdrückt)
•Ist lediglich ein Flügel vorhanden, so ist dennoch die
gesamte Abfolge auszuführen. Nach Beendigung des
Öffnungsvorganges des Flügels sind 5 Impulse Open zu
geben, bis der Flügel beginnt, sich zu schließen. Dann ist
die normale Vorgehensweise wieder aufzunehmen.
•Für einen störungsfreien Betrieb ist der mechanische
SICHERHEITENSCHLIESSUNG
Anschlag beim Öffnungs- und Schließvorgang unbedingt
SICHERHEITENSCHLIESSUNG
SieheAbschnitt5.2.
SieheAbschnitt5.2.
erforderlich.
KeineAuswirkung
KeineAuswirkung
KeineAuswirkung
KeineAuswirkung
6.3.4. LERNVERFAHREN ZEITEN MIT ENCODER + ENDSCHALTERN
Das Lernverfahren mit Gatecoder + Endschaltern kann auf zwei verschiedene
Weisen ausgeführt werden:
- EINFACHES LERNVERFAHREN:
Die gleiche Vorgehensweise wie beim Lernverfahren mit Endschaltern
ausführen. Der encoder wird lediglich als Hindernissensor eingesetzt.
- VOLLSTÄNDIGES LERNVERFAHREN:
Die gleiche Vorgehensweise wie beim Lernverfahren mit Endschaltern
KeineAuswirkung(speichertOPEN)
KeineAuswirkung(speichertOPEN)
UmkehrbeimSchließvorgang
UmkehrbeimSchließvorgang
ausführen. Der encoder wird lediglich als Hindernissensor eingesetzt.
SICHERHEITENÖFFNUNG
SICHERHEITENÖFFNUNG
KeineAuswirkung
KeineAuswirkung
KeineAuswirkung
KeineAuswirkung
Anmerkungen: • Sind einige Endschalter nicht installiert worden, so ist die
IMPULSE
IMPULSE
entsprechende Abbremsung mit einem Impuls Open zu
KeineAuswirkung(OPENunterdrückt)
KeineAuswirkung(OPENunterdrückt)
beginnen (der den Endschalter ersetzt).
• Ist lediglich ein Flügel vorhanden, so ist dennoch die
gesamte Abfolge auszuführen. Nach Beendigung des
Öffnungsvorganges des Flügels sind 5 Impulse Open zu
geben, bis der Flügel beginnt, sich zu schließen. Dann ist
die normale Vorgehensweise wieder aufzunehmen.
6.4. VORBLINKEN
KeineAuswirkung(OPENunterdrückt)
KeineAuswirkung(OPEN
BlockiertdenBetrieb
BlockiertdenBetrieb
Funktion des Vorblinkens aktiviert werden, die die Einschaltung der
unterdrückt)
Blinkleuchte 5 Sekunden vor dem Beginn der Bewegung der Flügel
STOP
STOP
ermöglicht.
Bei der Einschaltung des Vorblinkens ist folgendermaßen vorzugehen:
1 - überprüfen, ob das Tor geschlossen ist
2 - öffnen und den Stop-Kontakt offen halten
3 - überprüfen, ob die LED-Diode DL10 ausgeschaltet ist (leuchtet
ÖffnetdenfreigegebenenFlügelundschließtnach
ÖffnetdenFlügelunmittelbar
ÖffnetdenFlügelunmittelbar
4 - die Taste F kurz drücken und das Aufleuchten der LED-Diode DL10
Blockiert den Betrieb
AblaufderPausenzeitwieder(1)
AblaufderPausenzeitwieder
überprüfen
5 - den Stop-Kontakt wieder schließen (DL10 schaltet sich aus).
wieder(1)
wieder
OPEN-B
OPEN-B
wieder
Schließtdie/denFlügel
KeineAuswirkung(1)
ÖffnetdieFlügelunmittelbarwieder
4 - die Taste F kurz drücken und die Ausschaltung der LED-Diode DL10
Öffnet die Flügel und schließt nach
ÖffnetdieFlügelundschließtnach
AblaufderPausenzeitwieder
überprüfen
Blockiert den Betrieb
OPEN-A
(1)
IMÖFFNUNGSVORGANG
IMSCHLIESSVORGANG
IMSCHLIESSVORGANG
GEÖFFNETINPAUSE
GEÖFFNETINPAUSE
GESCHLOSSEN
GESCHLOSSEN
ZUSTANDTOR
ZUSTANDTOR
BLOCKIERT
BLOCKIERT
STEUERUNG "SP"
STEUERUNG"A"
Tab. 3/b
Tab. 3/a
39
Tab. 3/c
STEUERUNG"E" IMPULSE
ZUSTANDTOR OPEN-A OPEN-B STOP SICHERHEITENÖFFNUNG SICHERHEITENSCHLIESSUNG SICHERHEITENÖFFNUNG/SCHLIESSUNG W.L.
IMSCHLIESSVORGANG ÖffnetdieFlügelunmittelbarwieder ÖffnetdenFlügelunmittelbar BlockiertdenBetrieb KeineAuswirkung(speichertOPEN) SieheAbschnitt5.2. Blockierung und bei Freiwerden Umkehr in blinkt
wieder Öffnung
Tab. 3/d
STEUERUNG "EP" IMPULSE
ZUSTAND TOR OPEN-A OPEN-B STOP SICHERHEITEN ÖFFNUNG SICHERHEITEN SCHLIESSUNG SICHERHEITEN ÖFFNUNG/SCHLIESSUNG W.L.
GESCHLOSSEN Öffnet die Flügel Öffnet den freigegebenen Flügel Keine Auswirkung (OPEN unterdrückt) Keine Auswirkung Keine Auswirkung (OPEN unterdrückt) aus
GEÖFFNET Schließt die/den Flügel unverzüglich wieder Keine Auswirkung (OPEN unterdrückt) Keine Auswirkung (OPEN unterdrückt) ein
IM SCHLIESSVORGANG Blockiert den Betrieb Blockiert den Betrieb Keine Auswirkung (speichert OPEN) Siehe Abschnitt 5.2. Blockierung und bei Freiwerden Umkehr blinkt
in Öffnung
IM ÖFFNUNGSVORGANG Blockiert den Betrieb Umkehr beim Schließvorgang Keine Auswirkung Blockierung und bei Freiwerden ein
Fortsetzung der Öffnung
Setzt die Bewegung in umgekehrter Richtung fort Keine Auswirkung (OPEN Keine Auswirkung (soll geöffnet werden, wird Keine Auswirkung (soll geschlossen
BLOCKIERT Keine Auswirkung (OPEN unterdrückt) ein
(nach einem Stopp erfolgt stets Schließung) unterdrückt) OPEN unterdrückt) werden, wird OPEN unterdrückt)
40
Tab. 3/e
STEUERUNG "B" IMPULSE
ZUSTAND TOR OPEN-A OPEN-B STOP SICHERHEITEN ÖFFNUNG SICHERHEITEN SCHLIESSUNG SICHERHEITEN ÖFFNUNG/SCHLIESSUNG W.L.
Keine Auswirkung Keine Auswirkung Keine Auswirkung Keine Auswirkung aus
GESCHLOSSEN Öffnet die/den Flügel Keine Auswirkung (OPEN-A unterdrückt) (OPEN-A unterdrückt) (OPEN-A unterdrückt)
(OPEN-B unterdrückt)
Tab. 3/f
STEUERUNG "C" STETS GEDRÜCKTE STEUERUNGEN IMPULSE
ZUSTAND TOR OPEN-A OPEN-B STOP SICHERHEITEN ÖFFNUNG SICHERHEITEN SCHLIESSUNG SICHERHEITEN ÖFFNUNG/SCHLIESSUNG W.L.
Note supplémentaire:
Note aggiuntive: Notes: ces produits ont été soumis à des essais dans une
questi prodotti sono stati sottoposti a test in una configu- these products have been subject to testing procedures carried configuration typique homogène (tous les produits sont
razione tipica omogenea (tutti i prodotti di costruzione GE- out under standardised conditions (all products manufactured fabriqués par GENIUS s.r.l.).
NIUS s.r.l.). by GENIUS s.r.l.).
Declara que: El equipo electrónico JA592 erklärt: das elektronisch Gerät JA592 The descriptions and illustrations contained in the present
manual are not binding. GENIUS reserves the right, whils
leaving the main features of the equipments unaltered, to
• entspricht den wesentlichen undertake any modifications to holds necessary for either
Sicherheitsbestimmungen folgender Richtlinien: technical or commercial reasons, at any time and without
• Cumple los requisitos esenciales de seguridad
revising the present publication.
de las siguientes directivas: 73/23 EWG und nachträgliche Änderung 93/68 EWG
73/23 CEE y sucesiva modificación 93/68 CEE, 89/336 EWG und nachträgliche Änderung 92/31 EWG Les descriptions et les illustrations du présent manuel sont
89/336 CEE y sucesivas modificaciones 92/31 CEE y sowie 93/68 EWG fournies à titre indicatif. GENIUS se réserve le droit d’apporter
93/68 CEE. à tout moment les modifications qu’elle jugera utiles sur ce
produit tout en conservant les caractéristiques essentielles,
sans devoir pour autant mettre à jour cette publication .
Las descripciones y las ilustraciones de este manual no
Anmerkung: comportan compromiso alguno. GENIUS se reserva el
Nota: die o.g. produkte sind in einer typischen und einheitlichen weise derecho, dejando inmutadas las características esenciales
los productos mencionados han sido sometidos a pruebas getestet (alle von GENIUS s.r.l. gebaute produkte). de los aparatos, de aportar, en cualquier momento y sin
en una configuración típica homogénea (todo productos comprometerse a poner al día la presente publicación,
fabricado por GENIUS s.r.l.). todas las modificaciones que considere oportunas para el
perfeccionamiento técnico o para cualquier otro tipo de
Grassobbio, 1º de Marzo de 2002. exigencia de carácter constructivo o comercial.
Grassobbio, 1 März 2002
Der Geschäftsführer Die Beschreibungen und Abbildungen in vorliegendem
Administrador Delegado Handbuch sind unverbindlich. GENIUS behält sich das Recht
D. Gianantoni
D. Gianantoni vor, ohne die wesentlichen Eigenschaften dieses Gerätes zu
verändern und ohne Verbindlichkeiten in Bezung auf die
Neufassung der vorliegenden Anleitungen, technisch bzw,
konstruktiv / kommerziell bedingte Verbesserungen
vorzunehmen.
GENIUS s.r.l.
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO-ITALY
tel. 0039.035.4242511
fax. 0039.035.4242600
info@geniusg.com
www.geniusg.com
I0077 REV.4