Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SERIES
NOTE
MONTARBO COLORI STANDARD: NERO RAL 9
ARGENTO RAL 9006 , BIANCO RAL 9010
DISEGNO UNI ISO 128
QUOTE IN mm
TOLLERANZE NON SPECIFICATE U
MATERIALE PESO- Kg VO
F010510
DISEGNATO DA DESCRIZIONE
Andrea Malizia
PROPRIETARIO E RISERVATEZZA NUMERO DISEGNO REVISIONE
Le informazioni contenute in questo
disegno sono di proprietà esclusiva FIRE10LPMK2-AS00A
di Elettronica Montarbo srl.
Elettronica Montarbo S.r.l. Qualsiasi riproduzione parziale o SCALA FORMATO FOGLIO
totale senza l' autorizzazione di
1:5 A3
Via O. Pigini 8 - Z.I Aneto - 62010 Montelupone (MC) ITALY
www.montarbo.com - e-mail mail@montarbo.com Elettronica Montarbo è vietato.
tel. +39 0733 2271 - fax +39 07330227250
MANUALE D’ISTRUZIONI
OWNER’S MANUAL
ITALIANO - Norme di sicurezza 03
FIRE10LP MK2 04
Introduzione
Pannello
Dati tecnici
Parti di ricambio
FIRE12LP MK2 08
Introduzione
Pannello
Dati tecnici
Parti di ricambio
FIRE15LP MK2 12
Introduzione
Pannello
Dati tecnici
Parti di ricambio
FIRE10LP MK2 18
Introduction
Connection panel
Technical specifications
Spare parts
FIRE12LP MK2 22
Introduction
Connection panel
Technical specifications
Spare parts
FIRE15LP MK2 26
Introduction
Connection panel
Technical specifications
Spare parts
SCHEMA DI COLLEGAMENTO 30
LUGLIO 2018
UTILIZZO 31
Utilizzo a pavimento
Supporto piantana
Appendibilità tramite golfari
Appendibilità tramite staffe
ANGOLO DI COPERTURA 32
NOTE 33
Il lampo con la freccia inserito in un triangolo equilatero avvisa l’utilizzatore della presenza di tensione
pericolosa, senza isolamento, all’interno dell’apparecchio che potrebbe essere sufficientemente alta
da generare il rischio di scossa elettrica.
Il punto esclamativo inserito in un triangolo equilatero avvisa l’utilizzatore della presenza di importanti
istruzioni per l’utilizzo e per la manutenzione.
ATTENZIONE
Nell’interesse della propria e della altrui sicurezza, e per non invalidare
la garanzia, si raccomanda una attenta lettura di questa sezione
prima di utilizzare il prodotto.
Questo apparecchio è stato progettato e costruito per essere utilizzato come sistema
di altoparlanti con amplificatore nel contesto tipico di un sistema di amplificazione
sonora e/o di un sistema di registrazione sonora. L’utilizzo per scopi diversi da questi
non è contemplato dal costruttore, ed avviene pertanto sotto la diretta responsabilità
dell’utilizzatore/installatore.
ATTENZIONE
Questo apparecchio non contiene parti interne destinate all’intervento
diretto da parte dell’utilizzatore. Per evitare il rischio di incendio e/o
folgorazione, non smontarlo e non rimuovere il pannello posteriore.
Per qualsiasi intervento di manutenzione o riparazione, rivolgetevi
alla Elettronica Montarbo srl e/o a personale altamente qualificato
specificamente segnalato da questa.
CONTENUTO DELL’IMBALLO
◗ Sistema passivo
◗ Manuale d’istruzioni
◗ Certificato di garanzia
[H]
[I]
[B]
[F]
[I]
[I]
[A] Driver a compressione con gola da 1” e bobina da 1,4” caricato [F] Maniglia per il trasporto.
a tromba (dispersione 80° H x 60° V). [G] Pannello controlli e connessioni.
[B] Woofer ad alta efficienza da 10” con bobina da 2,5” e magnete [H] Adattatore per supporto asta.
in ferrite. [I] Punti di sospensione
[C] Cabinet in multistrato di betulla rifinito con vernice anti abrasioni.
[D] Griglia di protezione in acciaio. I materiali e la costruzione rispettano i più alti standard professionali
[E] Tubi di accordo. per assicurare la massima affidabilità.
FIRE10LP MK2
[1] [2]
[1] Connettore speakON® INPUT per il collegamento all'amplificatore. [2] Connettore speakON® LINK per il collegamento in parallelo di altri
Ad esso va collegato il cavo proveniente dall'amplificatore o dal diffusori. Esso è collegato in parallelo al connettore INPUT e permette
mixer amplificato. di inviare il segnale ad un secondo sistema di altoparlanti, tenendo
I contatti attivi sono [1+] e [1-]. conto dell'impedenza totale.
I contatti [2+] e [2-] non sono collegati [!] NOTA: Usare sempre cavi di potenza (cavi altoparlante) di
adeguata sezione (minimo 2 x 1.5 mm2) e qualità. Non usare cavi
schermati (cavi di segnale).
Attenzione! Non collegare mai due amplificatori alla stessa cassa.
speakON® è un marchio registrato da Neutrik® AG, registrato negli USA e altri Paesi.
Curva di risposta
[B02F147]
[A300230]
[A300198]
[D10F10L] [B010023]
[A30084]
[D20AF10]
A300198 B02F147
Tromba 80° X 60° Piastra di connessione
80° X 60° Horn Connection plate
A30084 D20AF10
Altoparlante 10" Griglia in acciaio perforato
10" loudspeaker Steel grille
[H]
[I]
[B]
[I]
[A] Driver a compressione con gola da 1” e bobina da 1,4” caricato [F] Maniglia per il trasporto.
a tromba (dispersione 80° H x 60° V). [G] Pannello controlli e connessioni.
[B] Woofer ad alta efficienza da 12” con bobina da 2,5” e magnete [H] Adattatore per supporto asta.
in ferrite. [I] Punti di sospensione
[C] Cabinet in multistrato di betulla rifinito con vernice anti abrasioni.
[D] Griglia di protezione in acciaio. I materiali e la costruzione rispettano i più alti standard professionali
[E] Tubi di accordo. per assicurare la massima affidabilità.
[1] [2]
[1] Connettore speakON® INPUT per il collegamento all'amplificatore. [2] Connettore speakON® LINK per il collegamento in parallelo di altri
Ad esso va collegato il cavo proveniente dall'amplificatore o dal diffusori. Esso è collegato in parallelo al connettore INPUT e permette
mixer amplificato. di inviare il segnale ad un secondo sistema di altoparlanti, tenendo
I contatti attivi sono [1+] e [1-]. conto dell'impedenza totale.
I contatti [2+] e [2-] non sono collegati [!] NOTA: Usare sempre cavi di potenza (cavi altoparlante) di
adeguata sezione (minimo 2 x 1.5 mm2) e qualità. Non usare cavi
schermati (cavi di segnale).
Attenzione! Non collegare mai due amplificatori alla stessa cassa.
speakON® è un marchio registrato da Neutrik® AG, registrato negli USA e altri Paesi.
Curva di risposta
[D21F12A]
[A300230]
[B010023]
[D1012PW]
[A300198]
[A300004]
[B02F125]
A300198 B02F125
Tromba 80° X 60° Piastra di connessione
80° X 60° Horn Connection plate
A300004 D21F12A
Altoparlante 12" Griglia in acciaio perforato
12" loudspeaker Steel grille
[H]
[I]
[B]
[E]
[I]
[A] Driver a compressione con gola da 1" e bobina da 1,4" caricato [F] Maniglie per il trasporto.
a tromba (dispersione 80° H x 60° V). [G] Pannello connessioni.
[B] Woofer ad alta efficienza da 15" con bobina da 2,5" e magnete [H] Adattatore per supporto asta.
in neodimio. [I] Inserti per appendimento 10MA (7 punti)
[C] Cabinet in multistrato di betulla rifinito con vernice anti abrasioni.
[D] Griglia di protezione in acciaio. I materiali e la costruzione rispettano i più alti standard professionali
[E] Tubi di accordo. per assicurare la massima affidabilità.
[1] [2]
[1] Connettore speakON® INPUT per il collegamento all'amplificatore. [2] Connettore speakON® LINK per il collegamento in parallelo di altri
Ad esso va collegato il cavo proveniente dall'amplificatore o dal diffusori. Esso è collegato in parallelo al connettore INPUT e permette
mixer amplificato. di inviare il segnale ad un secondo sistema di altoparlanti, tenendo
I contatti attivi sono [1+] e [1-]. conto dell'impedenza totale.
I contatti [2+] e [2-] non sono collegati [!] NOTA: Usare sempre cavi di potenza (cavi altoparlante) di
adeguata sezione (minimo 2 x 1.5 mm2) e qualità. Non usare cavi
schermati (cavi di segnale).
Attenzione! Non collegare mai due amplificatori alla stessa cassa.
speakON® è un marchio registrato da Neutrik® AG, registrato negli USA e altri Paesi.
Curva di risposta
Curva di risposta | Response curve
Appendix | Fire15LP
14 | Manuale d’istruzioni | Serie FIRE PASSIVE MK2
16
Parti di ricambio
[A300198]
[A300086]
[D21F15A]
[B010023]
[D1015PW]
[B02F149]
A300230
A300230 D1015PW
D1015PW B010023
B010023
Driver
Driver
a compressione
a compressionedada1,4"
1,4" Filtro
Filtro crossover Adattatore
Adattatoreper
perasta
asta
1.4"
1.4"
compression
compression
driver
driver Cross-over
Cross-over filter Speaker
Speakerstand
standadaptor
adaptor
A300198
A300198 D515LP0
B02F149
Tromba
Tromba
80°80°
X 60°
X 60° Pannello
Piastra diconnessioni
connessione
80°80°
X 60°
X 60°
Horn
Horn Connections
Connection plate
panel
A300086
A300086 D21F15A
D21F15A
Altoparlante
Altoparlante
15"15" Griglia
Griglia in acciaio perforato
perforato
15"15"
loudspeaker
loudspeaker Steel
Steel grille
Fire15LP | Appendix
The exclamation point in an equilateral triangle, is intended to alert the user to the presence of
important operating and maintenance instructions in the literature accompanying the product
WARNING
In order to protect your own and others’ safety and to avoid invalidation
of the warranty of this product, please read this section carefully before
operating this product.
• Never expose this product to rain or moisture, never use it in proximity of water
or in high humidity conditions. Never let any liquid, as well as any object, penetrate
the product. Should this be the case, do not use the speaker system and refer to
qualified servicing before operating it again. Never place burning candles or other
sources of open flame on top of the device.
• This product must be connected only to the output of a power amplifier or a powered
mixer. Always use a good quality speaker cable (unscreened), and check it frequently
for any damage to insulation and connectors.
• Before attempting to move the product after it has been installed, remove all the
connections.
• Before moving the product after it has been installed, or while it is operating, make
sure that the power amplifier is switched off.
• To disconnect this product from connecting cable never pull the cable directly:
hold it by the plug instead.
• Before placing the product on a surface of any kind, make sure that its shape and
load rating safely match the product size and weight.
• To avoid shocks, kicks, or whatever action, always reserve a protected area with no
access to unqualified personnel as installation site of the product.
In case the product is used near children and animals closest supervision is necessary.
• This product can generate very high acoustic pressures which are dangerous for
the hearing system. Always avoid operation at loud levels if anyone is excessively
near to the product (at least 1 m of distance).
CAUTION
This product does not contain user serviceable parts. To prevent fire and/or
electrical shock, never disassemble it or remove the rear panel. For mainte-
nance and servicing always refer to the official Montarbo Distributor in your
Country or to qualified personnel specifically authorised by the Distributor.
PACKAGE CONTENTS
◗ Passive loudspeaker system
◗ Owner’s manual
◗ Warranty certificate
[H]
[I]
[B]
[F]
[I]
[I]
[A] Compression driver with 1” throat and 1.4” voice coil, mounted on [F] Transport handle.
a constant-directivity horn (80° H x 60° V). [G] Connection panel.
[B] 10” high efficiency woofer with 2.5” voice coil and ferrite magnet. [H] Speaker stand adaptor.
[C] 15 mm birch multiply cabinet finished with anti-scratch paint. [I] 10MA hanging points (7 in total).
[D] Steel protection grille.
[E] Tuning ports. Construction and components conform to the highest professional
standards for maximum reliability.
FIRE10LP MK2
[1] [2]
[1] Input speakON® connector [INPUT]. Connect it to the power amplifier [2] Input link speakON® connector [LINK]. Wired in parallel to the input
or to the powered mixer output. connector, making it possible to drive another, parallel connected,
Active terminals are [1+] and [1–]. speaker system. Always pay attention to the total impedance.
Terminals [2+] and [2–] are not used. [!] NOTE: Use only loudspeaker cables (unscreened) having
suitable cross section (at least 2 x 1.5 mm2) and quality. Do not
twist or sharply bend the cables and do not allow for knots to be
formed, because they may result in insulation damage.Do not use
Warning! Never connect two amplifiers to the same loudspeaker. shielded cables (microphone/signal cables).
speakON® is a trademark under property of Neutrik® AG, registered in US and other Countries.
Response curve
[B02F147]
[A603061]
[A300230]
[A300198]
[D10F10L] [B010023]
[A30084]
[D20AF10]
A30084 A603061
Altoparlante 10" Connettori Neutrik® speakON®
10" loudspeaker Neutrik® speakON® connectors
[H]
[I]
[B]
[I]
[A] Compression driver with 1” throat and 1.4” voice coil, mounted on [F] Transport handle.
a constant-directivity horn (80° H x 60° V). [G] Connection panel.
[B] 12” high efficiency woofer with 2.5” voice coil and ferrite magnet. [H] Speaker stand adaptor.
[C] 15 mm birch multiply cabinet finished with anti-scratch paint. [I] 10MA hanging points (7 in total).
[D] Steel protection grille.
[E] Tuning ports. Construction and components conform to the highest professional
standards for maximum reliability.
[1] [2]
[1] Input speakON® connector [INPUT]. Connect it to the power amplifier [2] Input link speakON® connector [LINK]. Wired in parallel to the input
or to the powered mixer output. connector, making it possible to drive another, parallel connected,
Active terminals are [1+] and [1–]. speaker system. Always pay attention to the total impedance.
Terminals [2+] and [2–] are not used. [!] NOTE: Use only loudspeaker cables (unscreened) having
suitable cross section (at least 2 x 1.5 mm2) and quality. Do not
twist or sharply bend the cables and do not allow for knots to be
formed, because they may result in insulation damage.Do not use
Warning! Never connect two amplifiers to the same loudspeaker. shielded cables (microphone/signal cables).
speakON® is a trademark under property of Neutrik® AG, registered in US and other Countries.
Response curve
[D21F12A]
[A300230]
[B010023]
[D1012PW]
[A300198]
[A300004]
[A603061]
[B02F148]
A300004 A603061
Altoparlante 12" Connettori Neutrik® speakON®
12" loudspeaker Neutrik® speakON® connectors
[H]
[I]
[B]
[E]
[I]
[A] Compression driver with 1” throat and 1.4” voice coil, mounted on [F] Transport handle.
a constant-directivity horn (80° H x 60° V). [G] Connection panel.
[B] 15” high efficiency woofer with 2.5” voice coil and neodymium [H] Speaker stand adaptor.
magnet. [I] 10MA hanging points (7 in total).
[C] 15 mm birch multiply cabinet finished with anti-scratch paint.
[D] Steel protection grille. Construction and components conform to the highest professional
[E] Tuning ports. standards for maximum reliability.
[1] [2]
[1] Input speakON® connector [INPUT]. Connect it to the power amplifier [2] Input link speakON® connector [LINK]. Wired in parallel to the input
or to the powered mixer output. connector, making it possible to drive another, parallel connected,
Active terminals are [1+] and [1–]. speaker system. Always pay attention to the total impedance.
Terminals [2+] and [2–] are not used. [!] NOTE: Use only loudspeaker cables (unscreened) having
suitable cross section (at least 2 x 1.5 mm2) and quality. Do not
twist or sharply bend the cables and do not allow for knots to be
formed, because they may result in insulation damage.Do not use
Warning! Never connect two amplifiers to the same loudspeaker. shielded cables (microphone/signal cables).
speakON® is a trademark under property of Neutrik® AG, registered in US and other Countries.
Response curve
Curva di risposta | Response curve
Appendix | Fire15LP
28 | Owner’s manual | Series FIRE PASSIVE MK2
16
Spare parts
Parti di ricambio | Spare parts
[A300230]
[A300198]
[A300086]
[D21F15A]
[B010023]
[D1015PW]
[A603061]
[B02F149]
A300230
A300230 D1015PW
D1015PW D21F15A
B010023
Driver
Driver
a compressione
a compressionedada1,4"
1,4" Filtro
Filtro crossover Griglia
Adattatore
in acciaio
per asta
perforato
1.4"
1.4"
compression
compression
driver
driver Cross-over
Cross-over filter Steel
Speaker
grillestand adaptor
A300198
A300198 D515LP0
B02F149 B010023
Tromba
Tromba
80°80°
X 60°
X 60° Pannello
Piastra diconnessioni
connessione Adattatore per asta
80°80°
X 60°
X 60°
Horn
Horn Connections
Connection plate
panel Speaker stand adaptor
A300086
A300086 D21F15A
A603061
Altoparlante
Altoparlante
15"15" Griglia
Connettori Neutrik
in acciaio speakON®
perforato
®
15"15"
loudspeaker
loudspeaker Steel grille
Neutrik speakON connectors
® ®
Fire15LP | Appendix
Staffa lunga
Long bracket
Staffa corta
Short bracket
FIRE10LP MK2
FIRE12LP MK2
FIRE15LP MK2
Le informazioni contenute in questo manuale sono state attentamente redatte e controllate. Tuttavia The information contained in this manual have been carefully drawn up and checked. However
non si assume alcuna responsabilità per eventuali inesattezze. Questo manuale non può contenere una no responsibility will be assumed for any incorrectness. This manual cannot cover all the possible
risposta a tutti i singoli problemi che possono presentarsi durante l’installazione e l’uso dell’apparecchio. contingencies which may arise during the product installation and use. Should further information
Siamo a vostra disposizione per fornirvi eventuali ulteriori informazioni e consigli. Elettronica Montarbo be desired, please contact us or our local distributor. Elettronica Montarbo srl can not be considered
srl non può essere ritenuta responsabile per danni o incidenti a cose o persone, causati o connessi responsible for damages which may be caused to people and things when using this product.
all’utilizzazione o malfunzionamento dell’apparecchio.