Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
INFORMAZIONI GENERALI
GENERAL INFORMATION
I raccordi a saldare di testa della società Intertubi sono forniti in accordo alle seguenti norme:
Intertubi's butt welding fittings are provided in according to the following standards:
68
RACCORDI A SALDARE EN | BUTT WELDING FITTINGS EN
Le tabelle riportate in seguito permettono un confronto tra i differenti gradi di acciaio secondo la composizione chimica e le proprietà
meccaniche:
Tables shown below allow a comparision between the different steel grades according to the chemical composition and mechanical properties:
Grado acciaio /
Steel grade C Si Mn P S N Cr Cu Mo Nb Ni Ti Altri
EN max. max. max. max. max. max. max. max. max. max. max. max. Others
% % % % % % % % % % % % %
Nome / Names
X2CrNi18-9 1.4307 0,030 1,00 2,00 0,045 0,015 ≤ 0,11 17,50-19,50 - - - 8,00-10,00 - -
X5CrNi18-10 1.4301 0,07 1,00 2,00 0,045 0,015 ≤ 0,11 17,00-19,50 - - - 8,00-10,50 - -
X2CrNiMo17-12-2 1.4404 0,030 1,00 2,00 0,045 0,015 ≤ 0,11 16,50-18,50 - 2,00-2,50 - 10,00-13,00 - -
X5CrNiMo17-12-2 1.4401 0,07 1,00 2,00 0,045 0,015 ≤ 0,11 16,50-18,50 - 2,00-2,50 - 10,00-13,00 - -
LE TOLLERANZE, COME DA PAR 11.2 E EN 10253-4, SONO RIEPILOGATE NELLA SEGUENTE TABELLA:
TOLERANCES, AS EXPLAINED IN PAR 11.2 E EN 10253-4, ARE SUMMARIZED IN THE FOLLOWING TABLE:
Diametro esterno
Outside diameter Diametro interno Ovalità (2) Spessore (3) F-G-H-L B C K
D Inside diameter Out of round Thickness (mm) (mm) (mm) (mm)
(mm)
Alle estremità Sul corpo Alle estremità Sul corpo Alle estremità
At the ends On the body At the ends On the body At the ends
<=114,3 ±2mm ±7mm ±7mm ±4mm
Inclusa nella tolleranza del
>=139,7 <=219,1 diametro ±2mm ±7mm ±7mm ±7mm
Almeno 80% del -12,5%
273 diametro interno alle Included in the tolerance of ±5mm ±7mm ±10mm ±7mm
+15%
± 1% estremità the diameter
>=323,9 <=406,4 ±5mm ±10mm ±10mm ±7mm
min ± 0,5 mm Max 4%
>=457 <=610 (classe D2) At least 80% of the
±5mm ±10mm ±10mm ±7mm
internal diameter at
>=660 <=762 the ends Senza saldatura
Max 2% ±5mm ±10mm ±10mm ±7mm
Seamless
>762 -0,35 mm
+15% ±10mm ±10mm ±10mm ±10mm
(1) Le quote F-G-H-L-B-C-K sono riferite alle figure 1-2-3-4-5-6- (1) Dimensions are F-G-H-L-B-C-K are refering to the figures 1-2-
7-8-9-10-11-12 della EN 10253-4. 3-4-5-6-7-8-9-10-11-12 of EN 10253-4.
(2) L’ovalità deve essere così calcolata Ov=100(D max -D min)/D in (2) The out of roundness must be so calculate: Ov=100(D max -D
% dove: min
)/D in % where:
D max = diametro massimo misurato sulla sezione in mm D max = maximum diameter measured on the section in mm
D min = diametro minimo misurato sulla sezione in mm D min = minimum diameter measured on the section in mm
D = diametro nominale della sezione in mm D = nominal diameter of section in mm
(3) La tolleranza minima si applica anche sul corpo del raccordo (3) Minimum tolerance is applied also on the body of the fitting.
69
ACCIAIO INOX | STAINLESS STEEL
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
70
RACCORDI A SALDARE EN | BUTT WELDING FITTINGS EN
e
D
PESO TEORICO
Ø EST.MM SPESSORE RAGGIO
H THEORETICAL WEIGHT
OUTS. DIAM MM THICKNESS RADIUS
KG
2 0,07
21,3 45 55
3 0,08
2 0,11
26,9 57 70
3 0,14
2 0,18
33,7 72 88
3 0,27
2 0,29
42,4 93 114
3 0,45
2 0,39
48,3 108 132
3 0,61
2 0,62
60,3 135 165
3 0,89
2 1,01
76,1 175 213
3 1,44
2 1,39
88,9 205 250
3 2,07
2 2,35
114,3 270 327
3 3,49
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
71
ACCIAIO INOX | STAINLESS STEEL
CARATTERISTICHE TECNICHE
Ricavate da tubo saldato o lamiera
L Dimensioni tipo ISO 5251, forma diritta
d1 s
d2
CONCENTRIC AND ECCENTRIC REDUCERS
TECHNICAL INFORMATION
L
Made from welded pipe or plate
Dimensions type ISO 5251, straight form
s
d2
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
72
RACCORDI A SALDARE EN | BUTT WELDING FITTINGS EN
CARATTERISTICHE TECNICHE
Ricavate da tubo saldato o lamiera
L Dimensioni tipo ISO 5251, forma diritta
d1 s
d2
CONCENTRIC AND ECCENTRIC REDUCERS
TECHNICAL INFORMATION
L
Made from welded pipe or plate
Dimensions type ISO 5251, straight form
s
d2
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
73
ACCIAIO INOX | STAINLESS STEEL
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
74
RACCORDI A SALDARE EN | BUTT WELDING FITTINGS EN
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
75
ACCIAIO INOX | STAINLESS STEEL
D1
D
Ricavate da tubo saldato o lamiera
T1
T
Dimensioni e tolleranze in accordo EN 10253-3
L
D1
T
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
76
RACCORDI A SALDARE EN | BUTT WELDING FITTINGS EN
D1
D
Ricavate da tubo saldato o lamiera
T1
T
Dimensioni e tolleranze in accordo EN 10253-3
L
D1
T
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
77
ACCIAIO INOX | STAINLESS STEEL
F
T
T
D
T1
h
D1
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
78
RACCORDI A SALDARE EN | BUTT WELDING FITTINGS EN
PESO TEORICO
Ø D1 EST.MM O D1 SPESSORE
L H THEORETICAL WEIGHT
OUTS.DIAM MM THICKNESS
KG
21,3 2 50 18 0,04
26,9 2 58 22 0,05
33,7 2 76 26 0,13
42,4 2 95 33 0,19
2 0,40
60,3 127 44
3 0,62
2 0,55
76,1 152 53
3 0,83
2 0,80
88,9 171 60
3 1,00
2 1,18
114,3 210 67
3 1,70
2 1,50
139,7 248 81
3 2,60
2 2,20
168,3 286 96
3 3,20
2 3,40
219,1 356 120
3 5,30
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
79
ACCIAIO INOX | STAINLESS STEEL
T
derivazione saldato
D
G
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
80
RACCORDI A SALDARE EN | BUTT WELDING FITTINGS EN
T
derivazione saldato
D
G
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
81
ACCIAIO INOX | STAINLESS STEEL
T
Norma dimensionale EN 10253-3
Ricavati da tubo saldato o lamiera
D
G
F T1
T
D D1
EQUAL AND REDUCER WELDED TEE
F F F F TECHNICAL INFORMATION
T
T T1
D D1
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
82
RACCORDI A SALDARE EN | BUTT WELDING FITTINGS EN
T
Norma dimensionale EN 10253-3
Ricavati da tubo saldato o lamiera
D
G
F T1
T
D D1
EQUAL AND REDUCER WELDED TEE
F F F F TECHNICAL INFORMATION
T
T T1
D D1
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
83
ACCIAIO INOX | STAINLESS STEEL
FONDI BOMBATI
CARATTERISTICHE TECNICHE
Dimensioni tipo EN 10253-3 con altezze
secondo quanto esposto in tabella
CAPS
TECHNICAL INFORMATION
Dimensions type EN 10253-3 with lenght
according to the size table beside
K
T
R
2 26,0 0,19
101,6
3 27,0 0,28
Nota: i dati tecnici su questo catalogo sono indicativi e non impegnativi / Note: the technical data reported in this catalogue is proximative and not binding.
Data di emissione: 2020 Revisione: 01 / Date of issue: 2020 Revision: 01 - Copyright ® Intertubi S.p.a. Tutti i diritti riservati / Copyright ® Intertubi S.p.a. All rights reserved
84
RACCORDI A SALDARE EN | BUTT WELDING FITTINGS EN
85