Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
001
prohibits any person to reproduce it or make it known in whole or in part to other parties or
Classificazione dei Lubrificanti
Olii - Fluidi Resistenti al Fuoco - Grassi Rev. 13 Pag. 1 Di/Of 49
Classification of Lubricants Sostituisce
DANIELI
to competitors without specific written authorization of Danieli's Management.
1 - SCOPO 1 - PURPOSE
Scopo della presente Norma é di definire la tipologia dei lu- Aim of this Standard is to define the series of lubricants and
brificanti ed i criteri di scelta per la loro utilizzazione. the selection criteria for their use.
2 - ABBREVIAZIONI 2 - ABBREVIATIONS
NON APPLICABILE NOT APPLICABLE
3 - APPLICABILITA' 3 - APPLICATION
La presente Norma si applica nei casi e nelle condizioni defi- This Standard applies on the applications and operating con-
nite nell'ambito dei criteri di scelta; ditions listed in the selection criteria;
condizioni operative differenti da quelle indicate comportano different operating conditions by those selected require the
l'impiego di lubrificanti specifici da definire di volta in volta. use of detailed lubricants to be specified.
4 - DEFINIZIONI 4 - DEFINITIONS
La terminologia utilizzata nella presente Norma e le relative The terminology used in this STD and the relevant defini-
definizioni sono riportate nei documenti elencati nel capitolo tions are the ones applied to the documents mentioned in
5 "RIFERIMENTI". Chapter 5 - REFERENCES.
5 - RIFERIMENTI 5 - REFERENCES
Le Norme citate nel presente paragrafo si intendono sempre The STDs mentioned in this paragraph always apply to the
applicabili nello stato di revisione corrente. updated revision.
ASTM D 2265 : Test method for dropping point of lubricating ASTM D 2265 : Test method for dropping point of lubricating
grease over wide temperature range. grease over wide temperature range.
ASTM D 2266 : Test method for wear preventive characteri- ASTM D 2266 : Test method for wear preventive characteri-
stics of lubricating grease (Four-ball method). stics of lubricating grease (Four-ball method).
ASTM D 2270 : Practice for calculating viscosity index from ASTM D 2270 : Practice for calculating viscosity index from
kinematic viscosity at 40° and 100°C. kinematic viscosity at 40° and 100°C.
ASTM D 2272 : Test method for oxydation stability of steam ASTM D 2272 : Test method for oxydation stability of steam
turbine oils by rotating bomb. turbine oils by rotating bomb.
ASTM D 2509 : Test method for measurement of load-car- ASTM D 2509 : Test method for measurement of load-car-
rying capacity of lubricating grease (Timken method). rying capacity of lubricating grease (Timken method).
ASTM D 2596 : Test method for measurement of extreme ASTM D 2596 : Test method for measurement of extreme
pressure properties of lubricating grease (Four-ball pressure properties of lubricating grease (Four-ball
method). method).
ASTM D 2711 : Test method for demulsibility characteristics ASTM D 2711 : Test method for demulsibility characteristics
of lubricating oils. of lubricating oils.
ASTM D 2782 : Test method for measurement of extreme ASTM D 2782 : Test method for measurement of extreme
pressure properties of lubricating fluids (Timken met- pressure properties of lubricating fluids (Timken met-
hod). hod).
ASTM D 4172 : Test method for wear preventive characteri- ASTM D 4172 : Test method for wear preventive characteri-
stics of lubricating fluid (Four-ball method). stics of lubricating fluid (Four-ball method).
ASTM D 4928 : Test method for water in crude oils by coulo- ASTM D 4928 : Test method for water in crude oils by coulo-
metric Karl Fischer titration. metric Karl Fischer titration.
ASTM D 5182 : Test method for evaluating the scuffing (sco- ASTM D 5182 : Test method for evaluating the scuffing (sco-
ring) load capacity of oils (FZG visual method). ring) load capacity of oils (FZG visual method).
DIN 51354 : Testing of lubricants; mechanical testing by the DIN 51354 : Testing of lubricants; mechanical testing by the
FZG gear rig test method; method for A/8,3/90 lubrica- FZG gear rig test method; method for A/8,3/90 lubrica-
ting oil. ting oil.
DIN 51355 : Testing of lubricants; testing gear oils for their DIN 51355 : Testing of lubricants; testing gear oils for their
corrosion-inhibiting properties with respect to steel in corrosion-inhibiting properties with respect to steel in
the presence of water; method A and B. the presence of water; method A and B.
DIN 51381 : Testing of governor oils and hydraulic fluids; DIN 51381 : Testing of governor oils and hydraulic fluids;
determination of air release properties. determination of air release properties.
DIN 51389-2 : Testing of lubricants; mechanical testing of DIN 51389-2 : Testing of lubricants; mechanical testing of
hydraulic fluids by the vane-pump method; method A hydraulic fluids by the vane-pump method; method A
for anhydrous hydraulic fluids. for anhydrous hydraulic fluids.
DIN 51513 : Lubricants; lubricating oils B; minimum require- DIN 51513 : Lubricants; lubricating oils B; minimum require-
ments. ments.
DIN 51502 : Lubricants and related products; designation of DIN 51502 : Lubricants and related products; designation of
lubricants and marking the containers. lubricants and marking the containers.
DIN 51517-1 : C lubricating oils; minimum requirements. DIN 51517-1 : C lubricating oils; minimum requirements.
DIN 51517-3 : CLP lubricating oils; minimum requirements. DIN 51517-3 : CLP lubricating oils; minimum requirements.
DIN 51524-2 : Pressure fluids; HLP hydraulic oils; minimum DIN 51524-2 : Pressure fluids; HLP hydraulic oils; minimum
requirements. requirements.
DIN 51558-1 : Testing of petroleum products; determination DIN 51558-1 : Testing of petroleum products; determination
of neutralization number; colour indicator titration. of neutralization number; colour indicator titration.
DIN 51562 : Viscometry; measurement of kinem. viscosity. DIN 51562 : Viscometry; measurement of kinem. viscosity.
DIN 51587 : Testing of lubricants; determination of the age- DIN 51587 : Testing of lubricants; determination of the age-
ing behaviour of steam turbine oils and hydraulic oils ing behaviour of steam turbine oils and hydraulic oils
containing additives. containing additives.
DIN 51599 : Determination of demulsification capacity of DIN 51599 : Determination of demulsification capacity of
lubricating oils using the stirring method. lubricating oils using the stirring method.
DIN 51757 : Testing of petroleum products and related pro- DIN 51757 : Testing of petroleum products and related pro-
ducts; determination of density. ducts; determination of density.
DIN 51759-1 : Testing of liquid petroleum products; determi DIN 51759-1 : Testing of liquid petroleum products; determi
nation of the corrosive effect on copper; copper strip nation of the corrosive effect on copper; copper strip
test. test.
DIN 51802 : Testing of greases for corrosion-inhibiting pro- DIN 51802 : Testing of greases for corrosion-inhibiting pro-
perties (SKF-Emcor method). perties (SKF-Emcor method).
Classificazione dei Lubrificanti STANDARD No. 0.000.001
Olii - Fluidi Resistenti al Fuoco - Grassi Rev. 13 Pag. 5 Di/Of 49
Classification of Lubricants Sostituisce
DANIELI Oils - Fire-Resistant Hydraulic Fluids - Greases Replaces
DIN 51805 : Determination of flow pressure of lubricating DIN 51805 : Determination of flow pressure of lubricating
greases (Kesternich method). greases (Kesternich method).
DIN 51807 : Testing of lubricants; test on the behaviour of DIN 51807 : Testing of lubricants; test on the behaviour of
greases in the presence of water. greases in the presence of water.
DIN 51818 : Consistency classification of lubricating grea- DIN 51818 : Consistency classification of lubricating grea-
ses; NLGI grades. ses; NLGI grades.
DIN 51821-2 : Testing of lubricating greases using the FAG- DIN 51821-2 : Testing of lubricating greases using the FAG-
FE9 roller bearing grease testing machine; method A/ FE9 roller bearing grease testing machine; method A/
1500/6000. 1500/6000.
DIN 51825 : K lubricating greases; classification and require- DIN 51825 : K lubricating greases; classification and require-
ments. ments.
DIN 51826 : G lubricating greases; requirements. DIN 51826 : G lubricating greases; requirements.
EN 7 : Determination of ash from petroleum products. EN 7 : Determination of ash from petroleum products.
EN 10204 : Metallic products-Types of inspection docu- EN 10204 : Metallic products-Types of inspection docu-
ments. ments.
IEC 60156 : Insulating liquids Determination of the break IEC 60156 : Insulating liquids Determination of the break
down voltage at power frequency; test method. down voltage at power frequency; test method.
IEC 60296 : Specification for unused mineral insulating oils IEC 60296 : Specification for unused mineral insulating oils
for transformers and switchgear. for transformers and switchgear.
ISO 2137 : Petroleum products; lubricating grease; determi- ISO 2137 : Petroleum products; lubricating grease; determi-
nation of cone penetration. nation of cone penetration.
ISO 2160 : Petroleum products; corrosiveness to copper; ISO 2160 : Petroleum products; corrosiveness to copper;
copper strip test. copper strip test.
ISO 2176 : Petroleum products; determination of dropping ISO 2176 : Petroleum products; determination of dropping
point of greases. point of greases.
ISO 2592 : Petroleum products; determination of flash and ISO 2592 : Petroleum products; determination of flash and
fire points; Cleveland open cup method. fire points; Cleveland open cup method.
ISO 2909 : Petroleum products; determination of viscosity ISO 2909 : Petroleum products; determination of viscosity
index from kinematic viscosity. index from kinematic viscosity.
ISO 3016 : Petroleum products; determination of pour point. ISO 3016 : Petroleum products; determination of pour point.
ISO 3448 : Industrial liquid lubricants; ISO viscosity; classifi- ISO 3448 : Industrial liquid lubricants; ISO viscosity; classifi-
cation. cation.
ISO 4406 : Hydraulic fluid power; Fluids; Method for coding ISO 4406 : Hydraulic fluid power; Fluids; Method for coding
level of contamination by solid particles. level of contamination by solid particles.
ISO 6743-1 : Lubricants, industrial oils and related products ISO 6743-1 : Lubricants, industrial oils and related products
(class L); classification; family A (total loss systems). (class L); classification; family A (total loss systems).
ISO 6743-4 : Lubricants, industrial oils and related products ISO 6743-4 : Lubricants, industrial oils and related products
(class L); classification; family H (hydraulic systems). (class L); classification; family H (hydraulic systems).
ISO 6743-6 : Lubricants, industrial oils and related products ISO 6743-6 : Lubricants, industrial oils and related products
(class L); classification; family C (gears). (class L); classification; family C (gears).
ISO 6743-9 : Lubricants, industrial oils and related products ISO 6743-9 : Lubricants, industrial oils and related products
(class L); classification; family X (greases). (class L); classification; family X (greases).
ISO 6743-11 : Lubricants, industrial oils and related products ISO 6743-11 : Lubricants, industrial oils and related products
(class L); classification; family P (pneumatic tools). (class L); classification; family P (pneumatic tools).
VDE 0370-1 : Insulating oils;new insulating oils for transfor- VDE 0370-1 : Insulating oils;new insulating oils for transfor-
mers and switchgear. mers and switchgear.
6 - RESPONSABILITA' 6 - RESPONSIBILITY
NON APPLICABILE NOT APPLICABLE
Classificazione dei Lubrificanti STANDARD No. 0.000.001
Olii - Fluidi Resistenti al Fuoco - Grassi Rev. 13 Pag. 6 Di/Of 49
Classification of Lubricants Sostituisce
DANIELI Oils - Fire-Resistant Hydraulic Fluids - Greases Replaces
7 - NORMA 7 - STANDARD
Negli allegati seguenti, divisi per tipologia, sono elencati i mate- The following annexes list the materials treated in this STD,
riali oggetto della presente Norma. divided according to type.
Devono essere sempre accompagnati dalla relativa scheda Oils shall always be complete with safety card.
di sicurezza.
NOTE: NOTES:
-L'indicazione del tipo di lubrificante dovrà sempre fare riferi- -The type of lubricant shall always be referred to this Stan-
mento alla presente Norma, eccetto quei casi in cui é indi- dard, except when a product is to be defined by a specific
spensabile designare un prodotto con la sigla specifica del- acronym of the producing Company.
la Casa petrolifera.
-Le corrispondenze fra le specifiche Danieli ed il tipo di pro- -The correspondence between Danieli's specification and
dotto relativo, sono state indicate dai singoli Fabbricanti. In the associated product is specified by the various Sup-
caso di acquisto si suggerisce di ordinare non solo con la si- pliers. When purchasing a kindly state both the product
gla del prodotto ma anche con la Specifica Danieli. acronym and Danieli Specification.
Classificazione dei Lubrificanti STANDARD No. 0.000.001
Olii - Fluidi Resistenti al Fuoco - Grassi Rev. 13 Pag. 7 Di/Of 49
Classification of Lubricants Sostituisce
DANIELI Oils - Fire-Resistant Hydraulic Fluids - Greases Replaces
7.3 - TABELLA CORRISPONDENZA (Ex classificazione). 7.3 - CROSS REFERENCE TABLE (Old classification).
Tabella di corrispondenza tra i tipi di olii, fluidi resistenti Cross reference between oils, fire-resistant fluids and
al fuoco e grassi riportati nella Norma 0.000.001-Rev.05 greases types listed in superseded STD 0.000.001-
superata e l'attuale 0.000.001-Rev.07. Rev.05 and the applicable STD 0.000.001-Rev.07.
STD 0.000.001-Rev.05 - Superseded STD 0.000.001-Rev.07 - Revised Tab. 7.3/1
Type Designation CODE Design. CODE Notes OILS AND
DIN 51502 FIRE-RESISTANT
1 CLP 68 0.004981.Z - - Deleted FLUIDS
2 CLP 150 0.004982.S CLP 150 0.004982.S
3 CLP 220 0.004983.T CLP 220 0.004983.T
4 CLP 320 0.004984.R CLP 320 0.004984.R
5 CLP 460 0.004985.V CLP 460 0.004985.V
5a - - CLP 680 0.340322.T
6 CL 68 0.004986.W - - Deleted
7 CL 150 0.004987.X - - Deleted
8 CL 220 0.004988.F - - Deleted
9 CL 320 0.004989.G - - Deleted
10 HLP 46 0.004990.E HLP 46 0.341366.R 13-10 ISO 4406
13 11 HLP 68 0.004991.T HLP 68 0.341367.V 13-10 ISO 4406
12 CL 150 0.004992.R - - Use CLP 220
13 D 22 0.004993.V D 22 0.004993.V
14 C 100 0.004994.W - - Deleted
15 BC 0.004995.X - - Use OGF2G
16 C 320 0.014817.M - - Deleted
17 C 460 0.014818.V - - Deleted
18 C 32 0.069226.K C 32 0.069226.K
19 HLP 22 0.151149.L - - Deleted
20 J 0.151150.H J 0.151150.H
21 C 100 0.002117.R Danieli spec. 0.002117.R
22 C 220 0.086657.D Danieli spec. 0.086657.D BGV-ESS
23 C 320 0.092434.L Danieli spec. 0.092434.L Morgoil
24 C 460 0.081422.L Danieli spec. 0.081422.L specification
25 - - Danieli spec. 0.340321.S
31 PGP 460 0.151152.F - - Use CLP320/460
32 Gear couplings 0.151151.E - - Use CLP
33 Chains 150°C 0.151153.G BB-V 0.151153.G
34 Mould lubric. 0.151154.A FS 0.340325.W Vegetable-based
34a 0.340327.Z Syntetic-based
35 HFC 46 0.151165.D HFC VG 46 0.151165.D
36 HFD-U VG 46 0.151166.E HFD-U VG 46 0.151166.E
37 HFD-U VG 68 0.151314.A HFD-U VG 68 0.151314.A
Tab. A01.0/1b
Rif. APPLICAZIONI TIPICHE Designat. Danieli Parameters
Trans.
Ref. TYPICAL APPLICATIONS DIN 51502 CODE Speed Ratio Temp.°C Temp.°C Notes
Min Min - Max
A01.2.2a Lubrificazione a sbattimento di: CLP 220
A01.2.2b
-Ingranaggi, cuscinetti (riduttori). 0.004983.T -20°C
A01.2.2c (Type 3)
A01.2.2d
Splash lubrication on: CLP 320 <4 Max
0.004984.R − -10°C
-Gears, bearings (gear boxes). (Type 4) m/s 90°C
CLP 460 Speed
0.004985.V 0°C
(Type 5) reffered
CLP 150 to entry
0.004982.S -20°C shaft
(Type 2)
CLP 220 ≥ 4÷≤ 15 Max
0.004983.T - -10°C
(Type 3) m/s 90°C
CLP 320
0.004984.R 0°C
(Type 4)
A01.2.2c Lubrificazione a sbattimento di: CLP 320 ≥4 Max
A01.2.2d
-Riduttori a vite senza fine. 0.004984.R - 0°C Power
(Type 4) m/s 90°C
trans-
Splash lubrication on: CLP 460 <4 mission
0.004985.V 0°C
-Worm gears. (Type 5) m/s
ALL. 01-P.03 di 24 - OLII. STANDARD No. 0.000.001
Rev. 13 Pag. 12 Di/Of 49
ANN. 01-P.03 of 24 - OILS.
Sostituisce
DANIELI Replaces
Tab. A01.0/2
Rif. APPLICAZIONI TIPICHE Designat. Danieli Temp.°C Temp.°C
Ref. TYPICAL APPLICATIONS DIN 51502 CODE Min Max Notes
(pump start) (operating)
A01.3 Sistemi idraulici - Hydraulic systems
A01.3.1a Oli idraulici: Oli idraulici per dispositivi di comando con centrali HLP 46
13
A01.3.1b
oleodinamiche, che includono componenti molto caricati. 0.341366.R 10°÷30°C 60°C
(Type 10)
Hydraulic oils: Hydraulic fluids for control devices by hydraulic units, HLP 68
0.341367.V 10°÷50°C 60°C
which include highly loaded components. (Type 11)
A01.3.2a Fluidi resistenti al fuoco - Acqua-Glicole: Fluidi ininfiammabili, da
utilizzare in circuiti idraulici di macchine operanti in vicinanza di fiam-
me o punti ad alta temperatura (colata continua, forni, treni di lamina-
zione, trasportatori lingotti, trasporto siviere, ecc.). Utilizzato in tra-
smissioni idrauliche di comandi di potenza in circuiti operanti fino a
pressioni di 15 MPa.
HFC 46
Fire resistants hydraulic fluids - Water-Glycol: Non-flammable
0.151165.D 10°÷30°C 50°C
(Type 35)
fluids, to be used in hydraulic circuits of machines operating in the
vicinity of flames or sources of high temperature (continuous-casting
machines, furnaces, rolling trains, ingot conveyors, ladle cars, etc.).
These fluids are used in hydraulic transmissions of power drive
devices up to pressures of 15 MPa.
A01.3.2b Fluidi resistenti al fuoco - Esteri organici: Fluidi anidri, ad elevato
A01.3.2c
punto di accensione, da utilizzare in condizioni di limitato pericolo di
incendio e ove non sia possibile utilizzare prodotti contenenti acqua. HFD-U 46
Devono possedere resistenza alla propagazione della fiamma. Utiliz- 0.151166.E 10°÷30°C 70°C
(Type 36)
zato in trasmissioni idrauliche di comando e potenza in circuiti ope-
ranti fino a pressione di 70 MPa.
Fire resistants hydraulic fluids - Organic esters: Water-free fluids
with a high ignition point to be used in conditions of low fire hazard
and where it is not possible to use water-containing products. HFD-U 68
These fluids must be resistant to flame propagation. Used in hydraulic (Type 37)
0.151314.A 10°÷50°C 70°C
drive and power transmissions in circuits operating at pressures up to
70 MPa.
A01.4 Diversificati - Miscellaneous
A01.4.1a Lubrificazione linee ad aria compressa: Lubrificatori di linee ad aria
compressa; utensili pneumatici. D 22
0.004993.V - -
Compressed air lines lubrication: Compressed air lines lubrication; (Type 13)
pneumatic tools.
A01.4.2a Lubrificazione lingottiere: Olii per lubrificazione lingottiere. FS Vegetable
A01.4.2b 0.340325.W - -
Mould separation: Oils for mould lubrication. (Type 34) oil based
FS
0.340327.Z 0°C - Syntetic oil
(Type 34a)
A01.4.3a Olii per isolamenti elettrici: Olii per isolamenti elettrici di tra-
sformatori ed interruttori. J
0.151150.H - -
Oils for electrical insulation: Oils for electrical insulation of (Type 20)
transformers and switches.
A01.4.4a Olio per flussaggio: Olio per flussaggio di impianti lubrificazione e
oleodinamici. C 32
0.340324.V - -
(Type 18)
Flushing oils: Flushing oils for lubrication and hydraulic systems.
ALL. 01-P.04 di 24 - OLII. STANDARD No. 0.000.001
Rev. 13 Pag. 13 Di/Of 49
ANN. 01-P.04 of 24 - OILS.
Sostituisce
DANIELI Replaces
Ex. des.: 0.151153.G - Mineral oil BB-V DIN51513 Design. Design. Viscosity DANIELI Tab. A01.1.1a/1
46÷100 mm2/s at 100°C DIN 51502 ISO 6743-6 mm2/s @ 100°C CODE
T.33 N 0.000.001
Cert. EN10204 - 2.2 Type 33
BB-V L-CKH-DIL 46÷100
Preferibili ma non obbligatori. 0.151153.G
Preferred but not mandatory.
Caratteristiche Characteristics
Olio minerale bituminoso in solvente non infiammabile. Bituminous mineral oil in non flammable solvent.
Adesivo ed idrorepellente, ottima efficacia antiusura; Adhesive and water repellent, excellent anti-wear efficiency,
proprietà detergenti; viscosità dopo evaporazione solventi. detergent properties; viscosity after evaporation of the solvent.
Antigoccia. Temperatura max 150°C. Antidrop. Max temperature 150° C.
Supera DIN 51513. Exceeds DIN 51513.
Tab. A01.1.1a/2 Physical characteristics Tab. A01.1.1a/3
Characteristics STD ref. U.M. Value BRANDS COMPARISON
EN 7 SOCIETY MARK
Ash content g/100g ≤ 0,2
ASTM D 874 AGIP FIN 332/F
DIN 51599 KLINGFAST XX LT
Demulsibility - - BROOKS
ASTM D 2711 KLINGFAST EX LT
DIN 51757 Stated by ESSO SURETT FLUID NX
Density @ 15°C kg/dm3 Supplier
ASTM D 1298 FUCHS 13 CEPLATTYN KG 10HMF 2500
ISO 2592 KLÜBER GRAFLOSCON SY20 ULTRA
Flash Point °C ≥ 180
ASTM D 92 MOBILTAC LL (1)
DIN 51558-1 MOBIL
Neutralization number TAN mg KOH/g Neutral MOBILTAC 375 NC (2)
ASTM D 974
SHELL MALLEUS OGH
ISO 3016
Pour Point °C ≤6 CRATER 0
ASTM D 97 TEXACO
CRATER SPECIAL 0
DIN 51562 cSt
Viscosity @ 40°C (kinematic) - VISCOL SIGNAL GN/S/NF
ASTM D 445 mm2/s
DIN 51562 cSt (1): Only for USA market.
Viscosity @ 100°C (kinem.) (*) 49÷114 (2): Available in Europe.
ASTM D 445 mm2/s
ISO 2909
Viscosity Index - > 100
ASTM D 2270
Corrosion tests
Characteristics STD ref. U.M. Value
DIN 51759-1
Copper strip corrosion
ISO 2160 3h @ 100°C -
method A
ASTM D 130
DIN 51355/A Level 0-A
Corrosion-prevention ASTM D 665/A Demi water Pass
ASTM D 665/B Salt water -
Wear characteristics
Characteristics STD ref. U.M. Value
4-Ball wear test
ASTM D 4172/B wear mm -
40 kg 1200 g/1' 75°C 1h
4-Ball EP test (weld point) ASTM D 2596 kg -
Timken EP test (OK load) ASTM D 2782 pounds -
FZG gear test A/8.3/90 DIN 51354-1/2 Pass stage -
(*): Without solvent.
ALL. 01-P.05 di 24 - OLII. STANDARD No. 0.000.001
Rev. 13 Pag. 14 Di/Of 49
ANN. 01-P.05 of 24 - OILS.
Sostituisce
DANIELI Replaces
A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio. A01.2 - Pressure-fed, Splash, Oil mist lubrication.
A01.2.1a - Tipo ISO - VG 100 (Tipo 21). A01.2.1a - Type ISO - VG 100 (Type 21).
BGV lubrificazione cuscinetti non additivati EP. BGV bearings lubrication not additivated EP.
Viscosity Tab. A01.2.1a/1
Ex. des.: 0.002117.R - Mineral oil ISO VG 100 Design. Design. ISO VG 3448 DANIELI
T.21 N 0.000.001 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
Cert. EN10204 - 2.2 ± 10%
Type 21
Preferibili ma non obbligatori. - - 100
0.002117.R
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali paraffinici altamente raffinati, ottime resistenza all' Paraffinic highly refined mineral oils with oxidation and corro-
ossidazione, alla formazione di depositi, di protezione contro sion inhibitors, resistance to formation of sludge, free from acid
la corrosione, privi di acidi o altre impurità. Non contengono ad- and other impurities. Do not contain EP additives; allowed light
ditivi EP; ammessa leggera additivazione antiusura. antiwear additivation; max working temperature 170°C.
Temp. max lavoro 170°C. Filtrabile classe 15-12 ISO 4406. Product should be filtered down to 15-12 ISO 4406 class.
Eccellenti potere di separare rapidamente acqua, aria, altri Must separate rapidly from water, air and other contaminants long
contaminanti a lungo termine in servizio. term in service.
Tab. A01.2.1a/2 Physical characteristics Tab. A01.2.1a/3a
Characteristics STD ref. U.M. Value OILS ACTUALLY RUNNING
DIN 51381 AND TESTED ON FIELD
Air separation ability min. ≤ 15
02% @ 50°C BRANDS COMPARISON
Ash content ASTM D 874 % wt ≤ 0,1 SOCIETY MARK
Color ASTM D 1500 - Report BP ENERGOL MGX 88 13
Demulsibility (2) 36 ml min total free water
ASTM D 2711 (≥ 90% before centrifuging)
ESSO NURAY RM 100
Reagent-grade distilled water 45 ml water MOBIL VACUOLINE 525
1,5% water in oil max
405 ml oil @ 82°C 1,0 ml max oil emulsion SHELL MORLINA OIL T 100
ASTM D 1401 to 40-37-3
40 ml water min Tab. A01.2.1a/3b
40 ml oil @ 82°C in < 20'
OILS WHOSE SPECIFICATIONS MEET
DIN 51757 3 Stated by DANIELI'S REQUIREMENTS BUT NOT
Density @ 15°C kg/dm ACTUALLY RUNNING AND TESTED ON FIELD
ASTM D 1298 Supplier
Flash Point ISO 2592 BRANDS COMPARISON
°C > 220
Cleveland open cup ASTM D 92 SOCIETY MARK
Foaming tendency/stability (3) ASTM D 892 10/0
CASTROL MAGNA XX 100
ml/ml 30/0
24°-93°-24°C Seq. I-II-III 10/0 FUCHS RENOLIN MORGEAR 100
DIN 51587 TEXACO/CALTEX HONOR ASHLESS AW 100
Neutralization number TAN mg KOH/g ≤1
ASTM D 974 TOTAL CORTIS RM 100
Oxydation stability after 1000 h ASTM D 943 ∆ mg KOH/g ≤2 CEPSA CIRCULANTE 525
ISO 3016
Pour Point °C ≤ -10
ASTM D 97
DIN 51562 cSt
Viscosity @ 100°C (kinematic) 2 ≥ 10
ASTM D 445 mm /s
ISO 2909
Viscosity Index (1) - ≥ 95 Notes:
ASTM D 2270
(1)-No Viscosity Index (VI) improvers. Danieli must be
Corrosion tests notified if the VI is ≥ 120.
Characteristics STD ref. U.M. Value (2)-Danieli highly recommends that mill operators request
DIN 51759-1 that the following tests also be run using local roll coo-
Copper strip corrosion 3h @ 100°C max 1b lant to confirm that standard test results are valid for
ASTM D 130
ASTM D 665/A Demi water Pass the specific installation.
Corrosion-prevention (3)-Danieli don't recommend the addition of excess anti-
ASTM D 665/B Salt water Pass
foaming agents, as theytend to interfere with demulsi-
Rotary bomb oxydation test
ASTM D 2272 minutes min 140 vity and air release.
(RBOT)
(4)-The lubricant supplier shall assume responsibility for
Wear characteristics satisfactory in-service performance, and shall provide
Characteristics STD ref. U.M. Value assurance that the lubricant will not cause damage to
4-Ball wear test materials commonly used in the bearing assembly or
ASTM D 4172/A wear mm ≤ 0,3 the lubrication system. The lubricant supplier shall as-
15 kg 1200 g/1' 75°C 1h
sume responsibility for compatibility of the lubricant
4-Ball EP test (weld load) ASTM D 2596 kg ≥ 150
with any existing lubricant in the system. The lubricant
Timken EP test (OK load) ASTM D 2782 pounds - supplier should also assume responsibility for repair
DIN 51354-1/2 any equipment damage directly caused by a defect or
FZG gear test A/8.3/90 Pass stage 10
ASTM D 5182 malfunction of a selected lubricant, provided that the
lubricant was selected and maintained in accordance
with specifications of the original equipment manufac-
turer.
ALL. 01-P.06 di 24 - OLII. STANDARD No. 0.000.001
Rev. 13 Pag. 15 Di/Of 49
ANN. 01-P.06 of 24 - OILS.
Sostituisce
DANIELI Replaces
(A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio.) (A01.2 - Pressure-fed, Splash, Oil mist lubrication.)
A01.2.1b - Tipo ISO - VG 220 (Tipo 22). A01.2.1b - Type ISO - VG 220 (Type 22).
ESS lubrificazione cuscinetti non additivati EP. ESS bearings lubrication not additivated EP.
Viscosity Tab. A01.2.1b/1
Ex. des.: 0.086657.D - Mineral oil ISO VG 220 Design. Design. ISO VG 3448 DANIELI
T.22 N 0.000.001 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
Cert. EN10204 - 2.2 ± 10%
Type 22
Preferibili ma non obbligatori. - - 220
0.086657.D
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali paraffinici altamente raffinati, ottime resistenza all' Paraffinic highly refined mineral oils with oxidation and corro-
ossidazione, alla formazione di depositi, di protezione contro sion inhibitors, resistance to formation of sludge, free from acid
la corrosione, privi di acidi o altre impurità. Non contengono ad- and other impurities. Do not contain EP additives; allowed light
ditivi EP; ammessa leggera additivazione antiusura. antiwear additivation; max working temperature 170°C.
Temp. max lavoro 170°C. Filtrabile classe 15-12 ISO 4406. Product should be filtered down to 15-12 ISO 4406 class.
Eccellenti potere di separare rapidamente acqua, aria, altri Must separate rapidly from water, air and other contaminants long
contaminanti a lungo termine in servizio. term in service.
Tab. A01.2.1b/2 Physical characteristics Tab. A01.2.1b/3a
Characteristics STD ref. U.M. Value OILS ACTUALLY RUNNING
DIN 51381 AND TESTED ON FIELD
Air separation ability min. ≤ 15
02% @ 50°C BRANDS COMPARISON
Ash content ASTM D 874 % wt ≤ 0,1 SOCIETY MARK
Color ASTM D 1500 - Report BP ENERGOL MGX 220 13
Demulsibility (2) 36 ml min total free water
ASTM D 2711 (≥ 90% before centrifuging)
MOBIL VACUOLINE 533
Reagent-grade distilled water 45 ml water SHELL MORLINA OIL T 220
405 ml oil @ 82°C
1,5% water in oil max
1,0 ml max oil emulsion
13
ASTM D 1401 to 40-37-3
40 ml water min Tab. A01.2.1b/3b
40 ml oil @ 82°C in < 20'
OILS WHOSE SPECIFICATIONS MEET
DIN 51757 3 Stated by DANIELI'S REQUIREMENTS BUT NOT
Density @ 15°C kg/dm ACTUALLY RUNNING AND TESTED ON FIELD
ASTM D 1298 Supplier
Flash Point ISO 2592 BRANDS COMPARISON
°C > 230
Cleveland open cup ASTM D 92 SOCIETY MARK
Foaming tendency/stability (3) ASTM D 892 10/0
CASTROL MAGNA XX 220
ml/ml 30/0
24°-93°-24°C Seq. I-II-III 10/0 FUCHS RENOLIN MORGEAR 220
DIN 51587 ESSO NURAY RM 220
Neutralization number TAN mg KOH/g ≤1
ASTM D 974 TEXACO/CALTEX HONOR ASHLESS AW 220
Oxydation stability after 1000 h ASTM D 943 ∆ mg KOH/g ≤2 CEPSA CIRCULANTE 535
ISO 3016
Pour Point °C ≤ -10
ASTM D 97
DIN 51562 cSt
Viscosity @ 100°C (kinematic) 2 ≥ 18
ASTM D 445 mm /s
ISO 2909
Viscosity Index (1) - ≥ 95 Notes:
ASTM D 2270
(1)-No Viscosity Index (VI) improvers. Danieli must be
Corrosion tests notified if the VI is ≥ 120.
Characteristics STD ref. U.M. Value (2)-Danieli highly recommends that mill operators request
DIN 51759-1 that the following tests also be run using local roll coo-
Copper strip corrosion 3h @ 100°C max 1b lant to confirm that standard test results are valid for
ASTM D 130
ASTM D 665/A Demi water Pass the specific installation.
Corrosion-prevention (3)-Danieli don't recommend the addition of excess anti-
ASTM D 665/B Salt water Pass
foaming agents, as theytend to interfere with demulsi-
Rotary bomb oxydation test
ASTM D 2272 minutes min 140 vity and air release.
(RBOT)
(4)-The lubricant supplier shall assume responsibility for
Wear characteristics satisfactory in-service performance, and shall provide
Characteristics STD ref. U.M. Value assurance that the lubricant will not cause damage to
4-Ball wear test materials commonly used in the bearing assembly or
ASTM D 4172/A wear mm ≤ 0,3 the lubrication system. The lubricant supplier shall as-
15 kg 1200 g/1' 75°C 1h
sume responsibility for compatibility of the lubricant
4-Ball EP test (weld load) ASTM D 2596 kg ≥ 150
with any existing lubricant in the system. The lubricant
Timken EP test (OK load) ASTM D 2782 pounds - supplier should also assume responsibility for repair
DIN 51354-1/2 any equipment damage directly caused by a defect or
FZG gear test A/8.3/90 Pass stage 10
ASTM D 5182 malfunction of a selected lubricant, provided that the
lubricant was selected and maintained in accordance
with specifications of the original equipment manufac-
turer.
ALL. 01-P.07 di 24 - OLII. STANDARD No. 0.000.001
Rev. 13 Pag. 16 Di/Of 49
ANN. 01-P.07 of 24 - OILS.
Sostituisce
DANIELI Replaces
(A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio.) (A01.2 - Pressure-fed, Splash, Oil mist lubrication.)
A01.2.1c - Tipo ISO - VG 320 (Tipo 23). A01.2.1c - Type ISO - VG 320 (Type 23).
ESS lubrificazione cuscinetti non additivati EP. ESS bearings lubrication not additivated EP.
Viscosity Tab. A01.2.1c/1
Ex. des.: 0.092434.L - Mineral oil ISO VG 320 Design. Design. ISO VG 3448 DANIELI
T.23 N 0.000.001 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
Cert. EN10204 - 2.2 ± 10%
Type 23
Preferibili ma non obbligatori. - - 320
0.092434.L
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali paraffinici altamente raffinati, ottime resistenza all' Paraffinic highly refined mineral oils with oxidation and corro-
ossidazione, alla formazione di depositi, di protezione contro sion inhibitors, resistance to formation of sludge, free from acid
la corrosione, privi di acidi o altre impurità. Non contengono ad- and other impurities. Do not contain EP additives; allowed light
ditivi EP; ammessa leggera additivazione antiusura. antiwear additivation; max working temperature 170°C.
Temp. max lavoro 170°C. Filtrabile classe 15-12 ISO 4406. Product should be filtered down to 15-12 ISO 4406 class.
Eccellenti potere di separare rapidamente acqua, aria, altri Must separate rapidly from water, air and other contaminants long
contaminanti a lungo termine in servizio. term in service.
Tab. A01.2.1c/2 Physical characteristics Tab. A01.2.1c/3a
Characteristics STD ref. U.M. Value OILS ACTUALLY RUNNING
DIN 51381 AND TESTED ON FIELD
Air separation ability min. ≤ 20
02% @ 50°C BRANDS COMPARISON
Ash content ASTM D 874 % wt ≤ 0,1 SOCIETY MARK
Color ASTM D 1500 - Report BP ENERGOL MGX 320 13
Demulsibility (2) 36 ml min total free water
ASTM D 2711 (≥ 90% before centrifuging)
MOBIL VACUOLINE 537
Reagent-grade distilled water 45 ml water SHELL MORLINA OIL T 320
405 ml oil @ 82°C
1,5% water in oil max
1,0 ml max oil emulsion
13
ASTM D 1401 to 40-37-3
40 ml water min Tab. A01.2.1c/3b
40 ml oil @ 82°C in < 30'
OILS WHOSE SPECIFICATIONS MEET
DIN 51757 3 Stated by DANIELI'S REQUIREMENTS BUT NOT
Density @ 15°C kg/dm ACTUALLY RUNNING AND TESTED ON FIELD
ASTM D 1298 Supplier
Flash Point ISO 2592 BRANDS COMPARISON
°C > 250
Cleveland open cup ASTM D 92 SOCIETY MARK
Foaming tendency/stability (3) ASTM D 892 10/0
CASTROL MAGNA XX 320
ml/ml 30/0
24°-93°-24°C Seq. I-II-III 10/0 FUCHS RENOLIN MORGEAR 320
DIN 51587 ESSO NURAY RM 320
Neutralization number TAN mg KOH/g ≤1
ASTM D 974 TEXACO/CALTEX HONOR ASHLESS AW 320
Oxydation stability after 1000 h ASTM D 943 ∆ mg KOH/g ≤2
ISO 3016
Pour Point °C ≤ -6
ASTM D 97
DIN 51562 cSt
Viscosity @ 100°C (kinematic) 2 ≥ 24
ASTM D 445 mm /s
ISO 2909
Viscosity Index (1) - ≥ 95 Notes:
ASTM D 2270
(1)-No Viscosity Index (VI) improvers. Danieli must be
Corrosion tests notified if the VI is ≥ 120.
Characteristics STD ref. U.M. Value (2)-Danieli highly recommends that mill operators request
DIN 51759-1 that the following tests also be run using local roll coo-
Copper strip corrosion 3h @ 100°C max 1b lant to confirm that standard test results are valid for
ASTM D 130
ASTM D 665/A Demi water Pass the specific installation.
Corrosion-prevention (3)-Danieli don't recommend the addition of excess anti-
ASTM D 665/B Salt water Pass
foaming agents, as theytend to interfere with demulsi-
Rotary bomb oxydation test
ASTM D 2272 minutes min 140 vity and air release.
(RBOT)
(4)-The lubricant supplier shall assume responsibility for
Wear characteristics satisfactory in-service performance, and shall provide
Characteristics STD ref. U.M. Value assurance that the lubricant will not cause damage to
4-Ball wear test materials commonly used in the bearing assembly or
ASTM D 4172/A wear mm ≤ 0,3 the lubrication system. The lubricant supplier shall as-
15 kg 1200 g/1' 75°C 1h
sume responsibility for compatibility of the lubricant
4-Ball EP test (weld load) ASTM D 2596 kg ≥ 150
with any existing lubricant in the system. The lubricant
Timken EP test (OK load) ASTM D 2782 pounds - supplier should also assume responsibility for repair
DIN 51354-1/2 any equipment damage directly caused by a defect or
FZG gear test A/8.3/90 Pass stage 10
ASTM D 5182 malfunction of a selected lubricant, provided that the
lubricant was selected and maintained in accordance
with specifications of the original equipment manufac-
turer.
ALL. 01-P.08 di 24 - OLII. STANDARD No. 0.000.001
Rev. 13 Pag. 17 Di/Of 49
ANN. 01-P.08 of 24 - OILS.
Sostituisce
DANIELI Replaces
(A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio.) (A01.2 - Pressure-fed, Splash, Oil mist lubrication.)
A01.2.1d - Tipo ISO - VG 460 (Tipo 24). A01.2.1d - Type ISO - VG 460 (Type 24).
ESS lubrificazione cuscinetti non additivati EP. ESS bearings lubrication not additivated EP.
Viscosity Tab. A01.2.1d/1
Ex. des.: 0.081422.L - Mineral oil ISO VG 460 Design. Design. ISO VG 3448 DANIELI
T.24 N 0.000.001 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
Cert. EN10204 - 2.2 ± 10%
Type 24
Preferibili ma non obbligatori. - - 460
0.081422.L
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali paraffinici altamente raffinati, ottime resistenza all' Paraffinic highly refined mineral oils with oxidation and corro-
ossidazione, alla formazione di depositi, di protezione contro sion inhibitors, resistance to formation of sludge, free from acid
la corrosione, privi di acidi o altre impurità. Non contengono ad- and other impurities. Do not contain EP additives; allowed light
ditivi EP; ammessa leggera additivazione antiusura. antiwear additivation; max working temperature 170°C.
Temp. max lavoro 170°C. Filtrabile classe 15-12 ISO 4406. Product should be filtered down to 15-12 ISO 4406 class.
Eccellenti potere di separare rapidamente acqua, aria, altri Must separate rapidly from water, air and other contaminants long
contaminanti a lungo termine in servizio. term in service.
Tab. A01.2.1d/2 Physical characteristics Tab. A01.2.1d/3a
Characteristics STD ref. U.M. Value OILS ACTUALLY RUNNING
DIN 51381 AND TESTED ON FIELD
Air separation ability min. ≤ 20
02% @ 50°C BRANDS COMPARISON
Ash content ASTM D 874 % wt ≤ 0,1 SOCIETY MARK
Color ASTM D 1500 - Report BP ENERGOL MGX 460 13
Demulsibility (2) 36 ml min total free water
ASTM D 2711 (≥ 90% before centrifuging)
MOBIL VACUOLINE 546
Reagent-grade distilled water 45 ml water SHELL MORLINA OIL T 460
405 ml oil @ 82°C
1,5% water in oil max
1,0 ml max oil emulsion
13
ASTM D 1401 to 40-37-3
40 ml water min Tab. A01.2.1d/3b
40 ml oil @ 82°C in < 30'
OILS WHOSE SPECIFICATIONS MEET
DIN 51757 3 Stated by DANIELI'S REQUIREMENTS BUT NOT
Density @ 15°C kg/dm ACTUALLY RUNNING AND TESTED ON FIELD
ASTM D 1298 Supplier
Flash Point ISO 2592 BRANDS COMPARISON
°C > 250
Cleveland open cup ASTM D 92 SOCIETY MARK
Foaming tendency/stability (3) ASTM D 892 10/0
CASTROL MAGNA XX 460
ml/ml 30/0
24°-93°-24°C Seq. I-II-III 10/0 FUCHS RENOLIN MORGEAR 460
DIN 51587 ESSO NURAY RM 460
Neutralization number TAN mg KOH/g ≤1
ASTM D 974 TEXACO/CALTEX HONOR ASHLESS AW 460
Oxydation stability after 1000 h ASTM D 943 ∆ mg KOH/g ≤2 CEPSA CIRCULANTE 546
ISO 3016
Pour Point °C ≤ -6
ASTM D 97
DIN 51562 cSt
Viscosity @ 100°C (kinematic) 2 ≥ 28
ASTM D 445 mm /s
ISO 2909
Viscosity Index (1) - ≥ 95 Notes:
ASTM D 2270
(1)-No Viscosity Index (VI) improvers. Danieli must be
Corrosion tests notified if the VI is ≥ 120.
Characteristics STD ref. U.M. Value (2)-Danieli highly recommends that mill operators request
DIN 51759-1 that the following tests also be run using local roll coo-
Copper strip corrosion 3h @ 100°C max 1b lant to confirm that standard test results are valid for
ASTM D 130
ASTM D 665/A Demi water Pass the specific installation.
Corrosion-prevention (3)-Danieli don't recommend the addition of excess anti-
ASTM D 665/B Salt water Pass
foaming agents, as theytend to interfere with demulsi-
Rotary bomb oxydation test
ASTM D 2272 minutes min 140 vity and air release.
(RBOT)
(4)-The lubricant supplier shall assume responsibility for
Wear characteristics satisfactory in-service performance, and shall provide
Characteristics STD ref. U.M. Value assurance that the lubricant will not cause damage to
4-Ball wear test materials commonly used in the bearing assembly or
ASTM D 4172/A wear mm ≤ 0,3 the lubrication system. The lubricant supplier shall as-
15 kg 1200 g/1' 75°C 1h
sume responsibility for compatibility of the lubricant
4-Ball EP test (weld load) ASTM D 2596 kg ≥ 150
with any existing lubricant in the system. The lubricant
Timken EP test (OK load) ASTM D 2782 pounds - supplier should also assume responsibility for repair
DIN 51354-1/2 any equipment damage directly caused by a defect or
FZG gear test A/8.3/90 Pass stage 10
ASTM D 5182 malfunction of a selected lubricant, provided that the
lubricant was selected and maintained in accordance
with specifications of the original equipment manufac-
turer.
ALL. 01-P.09 di 24 - OLII. STANDARD No. 0.000.001
Rev. 13 Pag. 18 Di/Of 49
ANN. 01-P.09 of 24 - OILS.
Sostituisce
DANIELI Replaces
(A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio.) (A01.2 - Pressure-fed, Splash, Oil mist lubrication.)
A01.2.1e - Tipo ISO - VG 680 (Tipo 25). A01.2.1e - Type ISO - VG 680 (Type 25).
Lubrificazione cuscinetti gabbie per nastri, non additi- Strip stands bearings lubrication not additivated EP.
vati EP.
Viscosity Tab. A01.2.1e/1
Ex. des.: 0.340321.S - Mineral oil ISO VG 680 Design. Design. ISO VG 3448 DANIELI
T.25 N 0.000.001 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
Cert. EN10204 - 2.2 ± 10%
Type 25
Preferibili ma non obbligatori. - - 680
0.340321.S
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali paraffinici altamente raffinati, ottime resistenza all' Paraffinic highly refined mineral oils with oxidation and corro-
ossidazione, alla formazione di depositi, di protezione contro sion inhibitors, resistance to formation of sludge, free from acid
la corrosione, privi di acidi o altre impurità. Non contengono ad- and other impurities. Do not contain EP additives; allowed light
ditivi EP; ammessa leggera additivazione antiusura. antiwear additivation; max working temperature 170°C.
Temp. max lavoro 170°C. Filtrabile classe 15-12 ISO 4406. Product should be filtered down to 15-12 ISO 4406 class.
Eccellenti potere di separare rapidamente acqua, aria, altri Must separate rapidly from water, air and other contaminants long
contaminanti a lungo termine in servizio. term in service.
Tab. A01.2.1e/2 Physical characteristics Tab. A01.2.1e/3a
Characteristics STD ref. U.M. Value OILS ACTUALLY RUNNING
DIN 51381 AND TESTED ON FIELD
Air separation ability min. ≤ 20
02% @ 50°C BRANDS COMPARISON
Ash content ASTM D 874 % wt ≤ 0,1 SOCIETY MARK
Color ASTM D 1500 - Report BP ENERGOL MGX 680 13
Demulsibility (2) 36 ml min total free water
ASTM D 2711 (≥ 90% before centrifuging)
MOBIL VACUOLINE 548
Reagent-grade distilled water 45 ml water 1,5% water in oil max
405 ml oil @ 82°C 1,0 ml max oil emulsion
ASTM D 1401 to 40-37-3
40 ml water min Tab. A01.2.1e/3b
40 ml oil @ 82°C in < 50'
OILS WHOSE SPECIFICATIONS MEET
DIN 51757 3 Stated by DANIELI'S REQUIREMENTS BUT NOT
Density @ 15°C kg/dm ACTUALLY RUNNING AND TESTED ON FIELD
ASTM D 1298 Supplier
Flash Point ISO 2592 BRANDS COMPARISON
°C > 250
Cleveland open cup ASTM D 92 SOCIETY MARK
Foaming tendency/stability (3) ASTM D 892 10/0
CASTROL MAGNA XX 680
ml/ml 30/0
24°-93°-24°C Seq. I-II-III 10/0 FUCHS RENOLIN MORGEAR 680
DIN 51587 TEXACO/CALTEX HONOR ASHLESS AW 680
Neutralization number TAN mg KOH/g ≤1
ASTM D 974 CEPSA CIRCULANTE 548
Oxydation stability after 1000 h ASTM D 943 ∆ mg KOH/g ≤2
ISO 3016
Pour Point °C ≤0
ASTM D 97
DIN 51562 cSt
Viscosity @ 100°C (kinematic) 2 ≥ 32
ASTM D 445 mm /s
ISO 2909
Notes:
Viscosity Index (1) - ≥ 90 (1)-Danieli must be notified if the Viscosity Index (VI) is ≥
ASTM D 2270
120.
Corrosion tests (2)-Danieli highly recommends that mill operators request
Characteristics STD ref. U.M. Value that the following tests also be run using local roll coo-
DIN 51759-1 lant to confirm that standard test results are valid for
Copper strip corrosion 3h @ 100°C max 1a the specific installation.
ASTM D 130
ASTM D 665/A (3)-Danieli don't recommend the addition of excess anti-
Demi water Pass
Corrosion-prevention foaming agents, as theytend to interfere with demulsi-
ASTM D 665/B Salt water Pass
vity and air release.
Rotary bomb oxydation test
ASTM D 2272 minutes min 140 (4)-The lubricant supplier shall assume responsibility for
(RBOT)
satisfactory in-service performance, and shall provide
Wear characteristics assurance that the lubricant will not cause damage to
Characteristics STD ref. U.M. Value materials commonly used in the bearing assembly or
the lubrication system. The lubricant supplier shall as-
4-Ball wear test
ASTM D 4172/A wear mm ≤ 0,3 sume responsibility for compatibility of the lubricant
15 kg 1200 g/1' 75°C 1h
with any existing lubricant in the system. The lubricant
4-Ball EP test (weld load) ASTM D 2596 kg ≥ 150 supplier should also assume responsibility for repair
Timken EP test (OK load) ASTM D 2782 pounds - any equipment damage directly caused by a defect or
DIN 51354-1/2 malfunction of a selected lubricant, provided that the
FZG gear test A/8.3/90 Pass stage 10
ASTM D 5182 lubricant was selected and maintained in accordance
with specifications of the original equipment manufac-
turer.
ALL. 01-P.10 di 24 - OLII. STANDARD No. 0.000.001
Rev. 13 Pag. 19 Di/Of 49
ANN. 01-P.10 of 24 - OILS.
Sostituisce
DANIELI Replaces
(A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio.) (A01.2 - Pressure-fed, Splash, Oil mist lubrication.)
A01.2.2a - Tipo DIN 51502 - CLP 150 (Tipo 2). A01.2.2a - Type DIN 51502 - CLP 150 (Type 2).
Ingranaggi, cuscinetti Additivati EP. Gears, bearings Additivated EP.
Viscosity Tab. A01.2.2a/1
Ex. des.: 0.004982.S - Mineral oil CLP 150 Design. Design. ISO VG 3448 DANIELI
DIN 51517-3 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
T.2 N 0.000.001 ± 10%
Cert. EN10204 - 2.2
CLP Type 2
Preferibili ma non obbligatori. L-CKC-150 150
150 0.004982.S
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali altamente raffinati contenente additivi EP atti a mi- Highly refined mineral oils, containing EP additives improving
gliorare le proprietà contro la corrosione, la resistenza all'in- corrosion protection, ageing resistance, protection against
vecchiamento, ridurre l'usura. wear and scoring wear.
Temperature di impiego max 120°C. Max operating temperature: 120°C.
Supera DIN 51517 Parte 3. Exceeds DIN 51517 Part 3.
(A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio.) (A01.2 - Pressure-fed, Splash, Oil mist lubrication.)
A01.2.2b - Tipo DIN 51502 - CLP 220 (Tipo 3). A01.2.2b - Type DIN 51502 - CLP 220 (Type 3).
Ingranaggi, cuscinetti Additivati EP. Gears, bearings Additivated EP.
Viscosity Tab. A01.2.2b/1
Ex. des.: 0.004983.T - Mineral oil CLP 220 Design. Design. ISO VG 3448 DANIELI
DIN 51517-3 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
T.3 N 0.000.001 ± 10%
Cert. EN10204 - 2.2
CLP Type 3
Preferibili ma non obbligatori. L-CKC-220 220
220 0.004983.T
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali altamente raffinati, estratti al solvente, contenente Highly refined mineral oils, containing EP additives improving
additivi EP atti a migliorare le proprietà contro la corrosione, in- corrosion protection, ageing resistance, protection against
crementare la resistenza all'invecchiamento, ridurre l'usura. wear and scoring wear.
Temperature di impiego max 120°C. Max operating temperature: 120°C.
Supera DIN 51517 Parte 3. Exceeds DIN 51517 Part 3.
(A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio.) (A01.2 - Pressure-fed, Splash, Oil mist lubrication.)
A01.2.2c - Tipo DIN 51502 - CLP 320 (Tipo 4). A01.2.2c - Type DIN 51502 - CLP 320 (Type 4).
Ingranaggi, cuscinetti Additivati EP. Gears, bearings Additivated EP.
Viscosity Tab. A01.2.2c/1
Ex. des.: 0.004984.R - Mineral oil CLP 320 Design. Design. ISO VG 3448 DANIELI
DIN 51517-3 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
T.4 N 0.000.001 ± 10%
Cert. EN10204 - 2.2
CLP Type 4
Preferibili ma non obbligatori. L-CKC-320 320
320 0.004984.R
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali altamente raffinati, estratti al solvente, contenente Highly refined mineral oils, containing EP additives improving
additivi EP atti a migliorare le proprietà contro la corrosione, in- corrosion protection, ageing resistance, protection against
crementare la resistenza all'invecchiamento, ridurre l'usura. wear and scoring wear.
Temperature di impiego max 120°C. Max operating temperature: 120°C.
Supera DIN 51517 Parte 3. Exceeds DIN 51517 Part 3.
(A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio.) (A01.2 - Pressure-fed, Splash, Oil mist lubrication.)
A01.2.2d - Tipo DIN 51502 - CLP 460 (Tipo 5). A01.2.2d - Type DIN 51502 - CLP 460 (Type 5).
Ingranaggi, cuscinetti Additivati EP. Gears, bearings Additivated EP.
Viscosity Tab. A01.2.2d/1
Ex. des.: 0.004985.V - Mineral oil CLP 460 Design. Design. ISO VG 3448 DANIELI
DIN 51517-3 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
T.5 N 0.000.001 ± 10%
Cert. EN10204 - 2.2
CLP Type 5
Preferibili ma non obbligatori. L-CKC-460 460
460 0.004985.V
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali altamente raffinati, estratti al solvente, contenente Highly refined mineral oils, containing EP additives improving
additivi EP atti a migliorare le proprietà contro la corrosione, in- corrosion protection, ageing resistance, protection against
crementare la resistenza all'invecchiamento, ridurre l'usura. wear and scoring wear.
Temperature di impiego max 120°C. Max operating temperature: 120°C.
Supera DIN 51517 Parte 3. Exceeds DIN 51517 Part 3.
(A01.2 - Circolazione forzata, Sbattimento, A goccia d'olio.) (A01.2 - Pressure-fed, Splash, Oil mist lubrication.)
A01.2.2e - Tipo DIN 51502 - CLP 680 (Tipo 5a). A01.2.2e - Type DIN 51502 - CLP 680 (Type 5a).
Ingranaggi, cuscinetti Additivati EP. Gears, bearings Additivated EP.
Viscosity Tab. A01.2.2e/1
Ex. des.: 0.340322.T - Mineral oil CLP 680 Design. Design. ISO VG 3448 DANIELI
DIN 51517-3 DIN 51502 ISO 6743-6 mm2/s @ 40°C CODE
T.5a N 0.000.001 ± 10%
Cert. EN10204 - 2.2
CLP Type 5a
Preferibili ma non obbligatori. L-CKC-680 680
680 0.340322.T
Preferred but not mandatory.
Caratteristiche Characteristics
Olii minerali altamente raffinati, estratti al solvente, contenente Highly refined mineral oils, containing EP additives improving
additivi EP atti a migliorare le proprietà contro la corrosione, in- corrosion protection, ageing resistance, protection against
crementare la resistenza all'invecchiamento, ridurre l'usura. wear and scoring wear.
Temperature di impiego max 120°C. Max operating temperature: 120°C.
Supera DIN 51517 Parte 3. Exceeds DIN 51517 Part 3.
Ref. TYPICAL APPLICATIONS DIN 51502 CODE Load Power Speed Temp.°C Temp.°C Notes
Min Max
daN kW m/s Ambient Operating
A02.1 Grasso NON additivato EP - Grease NOT EP additivated
A02.1a Grasso multifunzionale: Grasso universale per
A02.1b K1K-20
impianti centralizzati per cuscinetti a rotolamento, 0.340331.R
(Type 4a)
motori elettrici, velocità normali, bassi carichi. Basso-medio
- - - 120°C
Multipurpose grease: Multipurpose grease for Low-medium
K2K-20
centralized system for rolling bearings, electric mo- 0.005004.A
(Type 4)
tors normal speed, low loads.
A02.1c Grasso multifunzionale: Grasso universale per
A02.1d
impianti centralizzati per cuscinetti a rotolamento e -20°C
K1R-20 ÷
strisciamento in presenza di elevate temperature e 0.340332.V
(Type 6a) 50°C
basse velocità: canalette doppie, tappeti di raffredda-
mento, settore curvo colata continua, rulli al piede.
Basso-medio
- - 160°C
Multipurpose grease: Multipurpose grease for Low-medium
centralized system for rolling and friction bearings, 0°C
K2R-20 ÷
operating at high temperatures and low speed: twin 0.005006.C
(Type 6) 50°C
channels, cooling conveyor, bens sector conti-
nuous casting, foot rollers.
A02.1e Grasso per basse temperature: Grasso adatto
per basse temperature ambientali. K1K-30
0.151164.C - - - -30°C 100°C
Low temperatures grease: Grease suitable for (Type 30)
low ambiental temperature
A02.2 Grasso additivato EP - Grease EP additivated
A02.2a Grasso multifunzionale: Grasso universale per
A02.2b
A02.2c impianti centralizzati per cuscinetti a rotolamento e
strisciamento, velocità normali, sollecitazioni gravo- KP0K-20 -20°C
÷
se: treni di laminazione, cuscinetti gabbie, via a rulli in (Type 1) 0.340328.G 30°C
genere, cesoie, raddrizzatrici, pattini (slitte).
Applicazioni singole con ingrassatore: bussole in ge-
nere, snodi, ingranaggi cilindrici e conici, viti senza fi-
ne, allunghe cardaniche, innesti scanalati.
KP1K-20 Medio-alto 0°C
0.340329.A Medium-high - ≤4 ÷ 100°C
Multipurpose grease: Multipurpose EP grease for (Type 2) 50°C
centralized system for rolling and friction bearings,
normal speed, heavy loads: rolling trains, stand
bearings, roller tables in general, shears, slides.
Single grease lubricator: bush in general, ball joints, 10°C
KP2K-20 ÷
spur and bevel gears, worms, spindles, grooved 0.340330.F
(Type 3) 50°C
couplings.
Tab. A02.0/1b
Rif. APPLICAZIONI TIPICHE Designat. Danieli Parameters
Ref. TYPICAL APPLICATIONS DIN 51502 CODE Load Power Speed Temp.°C Temp.°C Notes
Min Max
daN kW m/s Ambient Operating
A02.3 Grasso sintetico - Syntetic grease
A02.3a Grasso alta temperatura non additivato EP:
Grasso per lubrificazione centralizzata di cusci-
netti a rotolamento e strisciamento, in presenza di
calore. Temperature continue di 200°C.
KHC2S
High temperature grease not additivated EP: 0.340335.Z - - - - 200°C
(Type 21)
Grease for continuous lubrication of rolling or fric-
tion bearings with heat presence. To be used in
specific applications instead of mineral oil grease
based. Temperature up to 200°C.
A02.3b Grasso long-life additivato EP: Grasso sintetico
semifluido per riduttori a vite senza fine; applicazione
long-life. GPPG00K -10°C
0.341257.W - - 0,0667 ÷ 120°C
Long-life grease additivated EP: Semi-fluid (Type 9) 100°C
syntetic grease for worm-gear teeth; long-life ap-
plications.
A02.4 Grasso per sistemi aperti - Grease for open systems
A02.4a Grasso additivato EP per sistemi aperti: Ingra-
naggi scoperti lenti anche di grandi dimensioni,
fortemente caricati; funi; grandi comandi a catena,
eccentrici per placche. OGF2G Alto
0.340333.W - - - 120°C (1)
Grease for open systems additivated EP: Slow (Type 8) High
speed exposed gears even of large dimensions
and with heavy loads; steel ropes; large chain-
type drives, cammes for cooling beds.
A02.5 Pasta lubrificante infusibile - Lubricant infusible paste
A02.5a Grasso sintetico per altissime temperature:
Funi, catene e cerniere sul crogiolo; corsa elettro-
di; dispositivi inclinazione forno; tappi o saracine-
sche; viterie. Indicato per acciaio inossidabile. -
0.151157.D - - - - 1200°C
Syntetic grease for very high temperatures: (Type 22)
Ropes, chains and hinges on melting furnace, stro-
kes of electrodes, furnace tipping devices, stopper
or slide gates, screws. Suitable on stainless steel.
A02.6 Pasta di montaggio - Assembly paste
A02.6a Pasta di montaggio: Supporti colli cilindri; impie-
gata in montaggi in presenza di condensa e vibra-
zioni (es.: mandrini ESS). -
0.151163.B - - - - 120°C
Assembly paste: Rolling cylinder neck bearings; (Type 29)
used in assemblies with condensation and vibra-
tions (ex.: ESS spindles).
(1): Replaces applicacations of the formed oil BC.
ALL. 02-P.03 di 16 - GRASSI. STANDARD No. 0.000.001
Rev. 13 Pag. 36 Di/Of 49
ANN. 02-P.03 of 16 - GREASES.
Sostituisce
DANIELI Replaces
A02.1a - Tipo DIN 51502 - K1K-20 (Tipo 4a). A02.1a - Type DIN 51502 - K1K-20 (Type 4a).
Grassi multifunzionali NON additivati EP. Multipurpose greases NOT EP additives.
Tab. A02.1a/1
Ex. des.: 0.340331.R - Grease K1K-20 Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.4a N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
K Type 4a
L-XBCEA 1 310 340 1
1K-20 0.340331.R
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Elevata stabilità meccanica. High mechanical stability.
Buona resistenza contro: Ossidazione, corrosione, umidità, acqua. Good resistance against: Oxidation, corrosion, humidity and water.
Temp. -20°÷ +120°C. Temp. -20°÷ +120°C.
Conforme DIN 51825. Meet DIN 51825.
A02.1b - Tipo DIN 51502 - K2K-20 (Tipo 4). A02.1b - Type DIN 51502 - K2K-20 (Type 4).
Grassi multifunzionali NON additivati EP. Multipurpose greases NOT EP additives.
Tab. A02.1b/1
Ex. des.: 0.005004.A - Grease K2K-20 Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.4 N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
K Type 4
L-XBCEA 2 265 295 2
2K-20 0.005004.A
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Elevata stabilità meccanica. High mechanical stability.
Buona resistenza contro: Ossidazione, corrosione, umidità, acqua. Good resistance against: Oxidation, corrosion, humidity and water.
Temp. -20°÷ +120°C. Temp. -20°÷ +120°C.
Conforme DIN 51825. Meet DIN 51825.
A02.1c - Tipo DIN 51502 - K1R-20 (Tipo 6a). A02.1c - Type DIN 51502 - K1R-20 (Type 6a).
Grassi pompabili alte temperature, NON additivati EP. Pumbable greases for high temperature NOT EP addi-
tives.
Tab. A02.1c/1
Ex. des.: 0.340332.V - Grease K1R-20 Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.6a N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
K Type 6a
L-XBFEA 1 310 340 1
1R-20 0.340332.V
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Elevata stabilità meccanica. High mechanical stability.
Ottima resistenza contro ossidazione, corrosione, umidità, acqua. Excellent resistance to: Oxidation, corrosion, humidity and water.
Resistente a temperature continue fino 160°C (per brevi punte, fino a Resistance to continuous temperaturesup to 160°C (up to 180°C for
180°C). short intervals).
Basso contenuto in ceneri; pompabili. Low ash content; can be pumped.
Conformi DIN 51825. Meet DIN 51825.
A02.1d - Tipo DIN 51502 - K2R-20 (Tipo 6). A02.1d - Type DIN 51502 - K2R-20 (Type 6).
Grassi pompabili alte temperature, NON additivati EP. Pumbable greases for high temperature NOT EP addi-
tives.
Tab. A02.1d/1
Ex. des.: 0.005006.C - Grease K2R-20 Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.6 N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
K Type 6
L-XBFEA 2 265 295 2
2R-20 0.005006.C
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Elevata stabilità meccanica. High mechanical stability.
Ottima resistenza contro ossidazione, corrosione, umidità, acqua; Excellent resistance to: Oxidation, corrosion, humidity and water;
adesività. Resistente a temperature continue fino 160°C (per brevi adhesivity. Resistance to continuous temperaturesup to 160°C (up to
punte, fino a 180°C). 180°C for short intervals).
Basso contenuto in ceneri; pompabili. Low ash content; can be pumped.
Conformi DIN 51825. Meet DIN 51825.
A02.1e - Tipo DIN 51502 - K1K-30 (Tipo 30). A02.1e - Type DIN 51502 - K1K-30 (Type 30).
Lubrificazione per basse temperature, NON additivati EP. Low temperature lubrication NOT EP additives.
Tab. A02.1e/1
Ex. des.: 0.151164.C - Grease K1K-30 Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.30 N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
K Type 30
L-XCCEA 1 310 340 1
1K-30 0.151164.C
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Antiruggine e antiossidante. Corrosion inhibitors and anti-oxidants.
Temperatura di lavoro: -30°÷ +110°C. Working temperature: -30°÷ +110°C.
Conformi DIN 51825. Meet DIN 51825.
A02.2a - Tipo DIN 51502 - KP0K-20 (Tipo 1). A02.2a - Type DIN 51502 - KP0K-20 (Type 1).
Grassi multifunzionali additivati EP. Multipurpose greases EP additives.
Tab. A02.2a/1
Ex. des.: 0.340328.G - Grease KP0K-20 Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.1 N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
K Type 1
L-XBCEB 0 355 385 0
P0K-20 0.340328.G
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Elevata stabilità meccanica. High mechanical stability.
Buona resistenza contro: Ossidazione, corrosione, umidità, acqua. Good resistance against: Oxidation, corrosion, humidity and water.
Temperatura di impiego: -20°÷ +100°C. Operating temperature: -20°÷ +100°C.
Additivati EP, pompabile. Contain EP additives; can be pumped.
Conformi DIN 51825. Meet DIN 51825.
A02.2b - Tipo DIN 51502 - KP1K-20 (Tipo 2). A02.2b - Type DIN 51502 - KP1K-20 (Type 2).
Grassi multifunzionali additivati EP. Multipurpose greases EP additives.
Tab. A02.2b/1
Ex. des.: 0.340329.A - Grease KP1K-20 Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.2 N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
K Type 2
L-XBCEB 1 310 340 1
P1K-20 0.340329.A
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Elevata stabilità meccanica. High mechanical stability.
Buona resistenza contro: Ossidazione, corrosione, umidità, acqua. Good resistance against: Oxidation, corrosion, humidity and water.
Temperatura di impiego: -20°÷ +120°C. Operating temperature: -20°÷ +120°C.
Additivati EP, pompabile. Contain EP additives; can be pumped.
Conformi DIN 51825. Meet DIN 51825.
A02.2c - Tipo DIN 51502 - KP2K-20 (Tipo 3). A02.2c - Type DIN 51502 - KP2K-20 (Type 3).
Grassi multifunzionali additivati EP. Multipurpose greases EP additives.
Tab. A02.2c/1
Ex. des.: 0.340330.F - Grease KP2K-20 Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.3 N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
K Type 3
L-XBCEB 2 265 295 2
P2K-20 0.340330.F
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Elevata stabilità meccanica. High mechanical stability.
Buona resistenza contro: Ossidazione, corrosione, umidità, acqua. Good resistance against: Oxidation, corrosion, humidity and water.
Temperatura di impiego: -20°÷ +120°C. Operating temperature: -20°÷ +120°C.
Additivati EP, pompabile. Contain EP additives; can be pumped.
Conformi DIN 51825. Meet DIN 51825.
A02.2d - Tipo DIN 51502 - KPF2K-20 (Tipo 26). A02.2d - Type DIN 51502 - KPF2K-20 (Type 26).
Lubrificazione cuscinetti molto caricati, velocità lente. Lubrication of heavy loaded and slow bearings.
Tab. A02.2d/1
Ex. des.: 0.151160.L - Grease KPF2K-20 Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.26 N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
KPF Type 26
L-XACEB 2 265 295 2
2K-20 0.151160.L
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Ottima efficacia lubrificante in presenza di vibrazioni e sollecitazioni d'urto. Excellent lubricating efficiency in the presence of vibrations and impacts.
Ottima resistenza contro ossidazione, corrosione, condense, acqua. Excellent resistance against oxidation, condensation, water.
Temperatura max 120°C. Max temperature 120°C.
Additivato EP, alta adesività. Contains EP additives. High adesivity.
Conformi DIN 51825. Meet DIN 51825
A02.3a - Tipo DIN 51502 - KHC2S (Tipo 21). A02.3a - Type DIN 51502 - KHC2S (Type 21).
Sintetico - Lubrificazione alta temperatura, NON additi- Syntetic - High temperature lubrication, NOT EP addi-
vato EP. tives.
Tab. A02.3a/1
Ex. des.: 0.340335.Z - Grease KHC2S Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.21 N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
K HC Type 21
L-XBGEA 2 265 295 1.1/2÷2
2S 0.340335.Z
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Grasso a base di olio sintetico; ottima stabilità meccanica. Ottima resi- Grease with synthetic base oil; excellent mechanical stability. Excel-
stenza contro ossidazione, corrosione, umidità, acqua, vapore. lent resistance to oxidation, corrosion, humidity,water and steam.
Bassissimo residuo in ceneri, pompabile, adesivo, stabile anche a Very low ash content, can be pumped, good adhesiveness, stability
temperature continue di 200°C con punte di 220°C. even at continuous temp. of 200° with peaks of 220°C.
Conformi DIN 51825 Meet DIN 51825.
A02.3b - Tipo DIN 51502 - GPPG00K-20 (Tipo 9). A02.3b - Type DIN 51502 - GPPG00K-20 (Type 9).
Sintetico - Additivati EP. Syntetic - EP additives.
Tab. A02.3b/1
Ex. des.: 0.341257.W - Grease GPPG00K-20 Worked Penetration Consistence
DIN 51826 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.9 N 0.000.001 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
GP PG Type 9
L-XBCEB 00 400 430 00
00 K-20 0.341257.W
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Grasso semifluido a base sintetica. Synthetic semi-fluid grease.
Elevata stabilità meccanica e termica, temperatura: -20°÷ +120°C. High mechanical and thermal stability; temperature -20°÷ +120°C.
Ottima resistenza contro ossidazione, corrosione, condense. Excellent resistance to oxidation, corrosion, condensation.
Fortemente caricabile. Capability of supporting heavy loads.
Conformi DIN 51826. Meet DIN 51826.
A02.4a - Tipo DIN 51502 - OGF2G (Tipo 8). A02.4a - Type DIN 51502 - OGF2G (Type 8).
Ingranaggi scoperti, funi, catene. Open gears, ropes, chains.
Tab. A02.4a/1
Ex. des.: 0.340333.W - Grease OGF2G Worked Penetration Consistence
DIN 51825 Design. Design. DANIELI
DIN ISO 2137 NLGI
T.8 N 0.000.001 DIN 51502 ISO 6743 CODE
Min Max DIN 51818
Cert. EN10204 - 2.2
OG Type 8
L-XBCHA 2 265 295 1-2
F2G 0.340333.W
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Ottima stabilità meccanica; ottima resistenza contro ossidazione, cor- Excellent mechanical stability; excellent resistance to oxidation,
rosione, umidità, acqua; ottima adesività. corrosion, humidity and water; adhesiveness.
Additivato con grafite, MoS2, additivi EP. Contains graphite, MoS2, EP additives.
Temperatura impiego: 120°. Operating temperature 120°C.
Esente da bitumi. Bitumen free.
Conformi DIN 51825. Meet DIN 51825.
A02.5a - Pasta lubrificante infusibile (Tipo 22). A02.5a - Lubricant infusible paste (Type 22).
Sintetico - Lubrificazione altissima temperatura. Syntetic - Very-High temperature lubrication.
Tab. A02.5a/1
Ex. des.: 0.151157.D - Infusible paste Worked Penetration Consistence
T.22 N 0.000.001 Design. Design. DANIELI
DIN ISO 2137 NLGI
Cert. EN10204 - 2.2 DIN 51502 ISO 6743-9 CODE
Min Max DIN 51818
Type 22
- - - - (≅1)
0.151157.D
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Ottima stabilità meccanica; sintetico long life. Excellent mechanical stability Long-life synthetic.
Ottima protezione anticorrosione, anti-tribocorrosione, antigrippante. Excellent protection against corrosion, frictional corrosion, antiseizing.
Lubrificazione, anche a secco, per temp. fino a 1200°C. Lubrication, even dry, at temp. up to 1200°C.
Esente da piombo, zolfo, cadmio e nichel. Free of lead, sulphur, cadmium and nickel.
Resistenza all'acqua secondo DIN 51807-2 level 1. Water resistance according to DIN 51807/2 level1.
A02.6a - Pasta di montaggio (Tipo 29). A02.6a - Assembly paste (Type 29).
Paste di montaggio. Assembly paste.
Tab. A02.6a/1
Ex. des.: 0.151163.B - Assembly paste Worked Penetration Consistence
T.29 N 0.000.001 Design. Design. DANIELI
DIN ISO 2137 NLGI
Cert. EN10204 - 2.2 DIN 51502 ISO 6743 CODE
Min Max DIN 51818
Type 29
13 - - 220 295 2-3
0.151163.B
Preferibili ma non obbligatori.
Preferred but not mandatory.
Caratteristiche Characteristics
Pasta da montaggio con spiccata efficacia antiusura ed anti-tribocor- Assembly paste with good anti-wear and antifriction-corrosion effi-
rosione. ciency.
Idrorepellente, additivato, alta adesività. Water repellent, additived, high adhesivity.
Temperatura di impiego: -30°÷ +130°C. Operational temperature: -30°÷ +130°C.