Sei sulla pagina 1di 42

ITALIANO

ENGLISH

Elettromandrini rettangolari serie standard "HT/HM"

"HT/HM" standard series rectangular electro-spindles

Caratteristiche Features
Dimensioni d'ingombro Overall dimensions
Fissaggi standard disponibili Standard fixings available
Esecuzioni standard disponibili Standard versions available
Curve di potenza Power curves

25/07/2003 1/42
HT = versione studiata per lavorazioni leggere con carichi
sull'albero prevalentemente radiali.
HT = version designed for light machining with mainly
radial spindle loads.
Anteriore: 1 cuscinetto radiale. Front: 1 radial bearing.
Posteriore: 1 cuscinetto radiale. Rear: 1 radial bearing.

HM = versione studiata per lavorazioni pesanti con carichi


sull'albero radiali e assiali.
HM= version designed for heavy duty machining with both
radial and axial spindle loads.
Anteriore: 2 cuscinetti contatto obliquo. Front: 2 angular contact ball bearings
Posteriore: 1 cuscinetto radiale Rear: 1 radial bearing
2 cuscinetti contatto obliquo. 2 angular contact ball bearings

Nota: in questa pagina sono mostrate le dimensioni degli Note: The dimensions on this page refer to the unfinished
estrusi grezzi; per le dimensioni del motore finito vedere extrusions. See the detailed drawings later on for the
i disegni dettagliati piu' avanti dimensions of the finished motor.

Taglia 42 Taglia 55S Taglia 90


48

da pag. 6 da pag. 14 da pag. 30

67

120
63 Size 42 Size 55S Size 90
from page 6 70 from page 14 from page 30

103
Taglia 55 Taglia 73 Taglia 120
da pag. 10 da pag. 22 da pag. 38
80

93

Size 55 Size 73 Size 120

176
63 from page 10 from page 22 from page 38
82

145

25/07/2003 2/42
I PUNTI SALIENTI MAIN FEATURES

qualita' senza compromessi, certificata ISO9001; Incontrovertible and ISO 9001 certificated quality;
potenze superiori anche del 100% a parit di taglia a 100% higher power ranges than what is available on
quanto disponibile sul mercato; the market;
potenze dichiarate misurate al banco prova; declared power values are measured at the test bench;
grande possibilit di sovraccarico; wide possibility of overloads;
rispondenza alle normative; correspondence to the regulations;
rotore in rame; rotor in copper;
romorosit inferiore a quanto disponibile sul mercato; lower noisiness than what is available on the market;
temperatura di esercizio inferiore a quanto lower operative temperature than what is available on
disponibile sul mercato a parit di condizioni; the market;
corrente assorbita a vuoto ed a carico inferiore a lower loadless and load absorbed current than what is
quanto disponibile sul mercato a parit di condizioni; available on the market;
ventola proprietaria con efficienza migliorata, proprietary fan with improved efficiency, greater
maggior flusso generato con minor rumorosit; produced flow and lower noisiness
compensazione dei giochi dei cuscinetti con utensile compensation of bearing clearance with tool in thrust.
in spinta.

25/07/2003 3/42
PRESTAZIONI DEI GRUPPI ROTOSTATORICI ROTOR-STATOR GROUP PERFORMANCES

Velocit Massima
6000 rpm 12000 rpm 18000 rpm 18000 rpm 24000 rpm
Max. Speed

Velocit Nominale
6000 rpm 12000 rpm 12000 rpm 18000 rpm 18000 rpm
Nominal Speed

Taglia Motore Pagina


kW - rpm kW - rpm kW - rpm kW - rpm kW - rpm
Motor Size Page

42 - 080 0,30 - 12000 0,25 - 18000 0,45 - 18000 0,40 - 24000 6

55 - 090 0,65 - 12000 0,50 - 18000 1,00 - 18000 1,00 - 24000 10

55S - 055 0,35 - 12000 0,35 - 18000 0,55 - 18000 0,55 - 24000 14

55S - 090 0,65 - 12000 0,50 - 18000 1,00 - 18000 1,00 - 24000 18

73 - 070 1,30 - 12000 1,00 - 18000 2,00 - 18000 2,00 - 24000 22

73 - 140 2,40 - 12000 2,20 - 18000 3,50 - 18000 3,20 - 24000 26

90 - 100 3,50 - 12000 3,00 - 18000 4,50 - 18000 4,20 - 24000 30

90 - 140 5,00 - 12000 4,50 - 18000 6,00 - 18000 5,50 - 24000 34

120 - 170 8,10 - 6000 13,5 - 12000 12,00 - 18000 38

25/07/2003 4/42
DIAMETRI ACCETTATI DALLE PINZE "ER" ALLOWED DIAMETERS FOR "ER" COLLETS

PINZA
MIN MAX
COLLET
ER 11 1 mm 7 mm

ER 20 1 mm 13 mm

ER 25 2 mm 16 mm

ER 32 3 mm 20 mm

ER 40 3 mm 26 mm

Per le versioni pinza (alberi tipo P) sono Shaft and nut locking wrench for collet-type electrospindle
disponibili le chiavi di bloccaggio ghiera e albero. (type P shaft) are available on request.

25/07/2003 5/42
Elettromandrino taglia 42-080 Size 42-080 electro-spindle
Dimensioni di ingombro Overall dimensions

Velocit di rotazione Peso : ~ 2 kg Minimum rotation


minima 7000 rpm Weight : ~ 2 kg speed 7000 rpm

68 61 22 46

-0,009
-0,034
-0,011

O 43 g7
+0
27
Versione Albero tipo "L"

O 16 h6
con morsettiera albero liscio CH 17

Version Type "L" shaft

O 18,7
with terminals smooth shaft

M8
15 12
27 31

102 41,5 65

-0,009
-0,009
-0,034

-0,034
O 43 g7

O 43 g7
Albero tipo "P" Versione Albero tipo "T"

26,5
CH 13 CH 17
pinza ER11 con connettore albero con linguetta Linguetta 5x5x12
O 11
16

48
Type "P" shaft Version Type "T" shaft

M 16 x 1,5

-0,011
M 14 x 0,75

ER11 collet with connector keyed shaft

+0

O 18,7
O 16 h6
20 31 130 23 63

13 15 12
40 31

25/07/2003 6/42
Elettromandrino taglia 42-080 Size 42-080 electro-spindle
Fissaggi standard disponibili Standard fixings available

N.B. N.B.
Il profilo della carcassa non rende Because of the body profile, the
disponibili le versioni con la foratura di versions with RH and LH side mounting
montaggio laterale Dx e laterale Sx. holes are not available.

5
43
41

43
= =

M 5 - n 6 fori

Fissaggio inferiore Bottom fixing

48
63

Come ordinare How to order Esempio di Example of a


compilazione ordine compiled order
Taglia attacco Potenza Velocit Curva Esecuzione Taglia attacco Potenza Velocit Curva Esecuzione
Fissaggio Fissaggio
elettromandrino utensile (kW) (rpm) tipo n elettromandrino utensile (kW) (rpm) tipo n
Electro-spindle tool Power Speed Curve Version Electro-spindle tool Power Speed Curve Version
Fixing Fixing
size type (kW) (rpm) type n size type (kW) (rpm) type n
____-___ _ _,__ _____ __ __ _ 42-080 P 0,25 18000 42 1B 1

25/07/2003 7/42
Caratteristiche Elettriche Esecuzioni standard
Electrical specifications Standard versions
Elettromandrino Attacco utensile
Corrente nominale Curva di
Nominal current potenza
380 V 220 V
Electro-spindle Tool type Tipo fissaggio
Power Morsettiera Connettore Morsettiera Connettore Fixing type
Kw rpm 380V 220V curve
Terminals Connector Terminals Connector

0,30 12000 1,0 A 1,7 A 41


0 = Speciale
Albero tipo "P" 0 = Special
pinza ER11 0,25 18000 0,9 A 1,6 A 42
1 1A 1B 1C
Type "P" shaft 0,45 18000 1,5 A 2,6 A 43
ER11 collet 1 = Inferiore
1 = Bottom
0,40 24000 1,4 A 2,5 A 44

42-080 0,30 12000 1,0 A 1,7 A 41


0 = Speciale
Albero tipo "L" 0 = Special
2 Poli albero liscio 0,25 18000 0,9 A 1,6 A 42
1 1A 1B 1C
2 Poles Type "L" shaft 0,45 18000 1,5 A 2,6 A 43
smooth shaft 1 = Inferiore
1 = Bottom
0,40 24000 1,4 A 2,5 A 44

0,30 12000 1,0 A 1,7 A 41 0 = Speciale


Albero tipo "T"
0 = Special
albero con linguetta
0,25 18000 0,9 A 1,6 A 42 1 1A 1B 1C
Type "T" shaft
1 = Inferiore
keyed shaft 1 = Bottom
0,45 18000 1,5 A 2,6 A 43

25/07/2003 8/42
Curve di potenza Power curves

350 350
300 300
250 250
potenza [W]

potenza [W]
200 200
150 150
100 100
50 50
0 0
6000 7000 8000 9000 10000 11000 12000 6000 8000 10000 12000 14000 16000 18000
rpm rpm

Curva di potenza 41 Power curve 41 Curva di potenza 42 Power curve 42


Velocit max = 12000 Max. speed = 12000 Velocit max = 18000 Max. speed = 18000
Vel. Nominale = 12000 Nominal speed = 12000 Vel. Nominale = 12000 Nominal speed = 12000

500
500
400
400

potenza [W]
potenza [W]

300 300

200 200

100 100

0 0
6000 8000 10000 12000 14000 16000 18000 6000 9000 12000 15000 18000 21000 24000
rpm rpm

Curva di potenza 43 Power curve 43 Curva di potenza 44 Power curve 44


Velocit max = 18000 Max. speed = 18000 Velocit max = 24000 Max. speed = 24000
Vel. Nominale = 18000 Nominal speed = 18000 Vel. Nominale = 18000 Nominal speed = 18000

25/07/2003 9/42
Elettromandrino taglia 55-090 Size 55-090 electro-spindle
Dimensioni di ingombro Overall dimensions

Velocit di rotazione Peso : ~ 4 kg Minimum rotation


minima 7000 rpm Weight : ~ 4 kg speed 7000 rpm

89,5 61 22 46
CH 20

-0,029
-0,01
O 23,5
27

O 56 g6
Versione Albero tipo "L"

M8
-0,011
con morsettiera albero liscio

+0
O 16 h6
20 11
31 37,5
Version Type "L" shaft
with terminals smooth shaft

O 23,5
121 41,5 65 CH 20
Linguetta 5x5x12

26,5

-0,029
-0,01
Albero tipo "P" CH 20 Versione Albero tipo "T"

O 56 g6
pinza ER20 con connettore albero con linguetta
-0,029
-0,01
M 25 x 1,5

-0,011
M 16 x 1,5
O 20
16

80

+0
O 56 g6

O 16 h6
Type "P" shaft Version Type "T" shaft
ER20 collet 27,5 37,5 153,5 29 63 with connector keyed shaft 15 20 11
46 37,5

25/07/2003 10/42
Elettromandrino taglia 55-090 Size 55-090 electro-spindle
Fissaggi standard disponibili Standard fixings available

19,5
Fissaggio inferiore
Bottom fixing

110
22
= =
M 6 - n 4 fori

Fissaggio laterale Dx Fissaggio laterale Sx


RH side fixing LH side fixing

40
40

80
= =

= =
M 6 - n 4 fori M 6 - n 4 fori
19,5 110 63 110 19,5

Come ordinare How to order Esempio di Example of a


compilazione ordine compiled order
Taglia attacco Potenza Velocit Curva Esecuzione Taglia attacco Potenza Velocit Curva Esecuzione
Fissaggio Fissaggio
elettromandrino utensile (kW) (rpm) tipo n elettromandrino utensile (kW) (rpm) tipo n
Electro-spindle tool Power Speed Curve Version Electro-spindle tool Power Speed Curve Version
Fixing Fixing
size type (kW) (rpm) type n size type (kW) (rpm) type n
____-___ _ _,__ _____ __ __ _ 55-090 P 0,5 18000 52 1B 1

25/07/2003 11/42
Caratteristiche Elettriche Esecuzioni standard
Electrical specifications Standard versions
Elettromandrino Attacco utensile
Corrente nominale Curva di
Nominal current 380 V 220 V
potenza Tipo Fixing
Electro-spindle Tool type Kw rpm Power Morsettiera Connettore Morsettiera Connettore fissaggio type
380V 220V curve Terminals Connector Terminals Connector
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
0,65 12000 1,8 A 3,2 A 51 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "P" 1 = Inferiore 1 = Bottom
pinza ER20 0,50 18000 1,5 A 2,6 A 52 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Type "P" shaft 1,00 18000 3,2 A 5,5 A 53 1 1A 1B 1C 1 = Inferiore 1 = Bottom
2 = Laterale Dx 2 = RH side
ER20 collet 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
1,00 24000 3,2 A 5,5 A 54 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
0,65 12000 1,8 A 3,2 A 51 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
55-090 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "L" 1 = Inferiore 1 = Bottom
2 Poli albero liscio 0,50 18000 1,5 A 2,6 A 52 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
2 Poles Type "L" shaft 1 = Inferiore 1 = Bottom
1,00 18000 3,2 A 5,5 A 53 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
smooth shaft 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
1,00 24000 3,2 A 5,5 A 54 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
Albero tipo "T" 0,65 12000 1,8 A 3,2 A 51 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
albero con 0 = Speciale 0 = Special
linguetta 1 = Inferiore 1 = Bottom
0,50 18000 1,5 A 2,6 A 52 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
Type "T" shaft 0 = Speciale 0 = Special
keyed shaft 1,00 18000 3,2 A 5,5 A 53 1 1A 1B 1C 1 = Inferiore 1 = Bottom
2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side

25/07/2003 12/42
Curve di potenza Power curves

700 700
600 600
500 500
potenza [W]

potenza [W]
400 400
300 300
200 200
100 100
0 0
6000 7000 8000 9000 10000 11000 12000 6000 8000 10000 12000 14000 16000 18000
rpm rpm

Curva di potenza 51 Power curve 51 Curva di potenza 52 Power curve 52


Velocit max = 12000 Max. speed = 12000 Velocit max = 18000 Max. speed = 18000
Vel. Nominale = 12000 Nominal speed = 12000 Vel. Nominale = 12000 Nominal speed = 12000

1200
1200
1000
1000

potenza [W]
800
potenza [W]

800
600 600

400 400

200 200

0 0
6000 8000 10000 12000 14000 16000 18000 6000 9000 12000 15000 18000 21000 24000
rpm rpm

Curva di potenza 53 Power curve 53 Curva di potenza 54 Power curve 54


Velocit max = 18000 Max. speed = 18000 Velocit max = 24000 Max. speed = 24000
Vel. Nominale = 18000 Nominal speed = 18000 Vel. Nominale = 18000 Nominal speed = 18000

25/07/2003 13/42
Elettromandrino taglia 55S-055 Size 55S-055 electro-spindle
Dimensioni di ingombro Overall dimensions

Velocit di rotazione Peso : ~ 3 kg Minimum rotation


minima 7000 rpm Weight : ~ 3 kg speed 7000 rpm

89,5 61 22 46

-0,029
-0,01
O 56 g6
27
Versione Albero tipo "L" CH 20
con morsettiera albero liscio

O 23,5

M8
-0,011
+0
Version Type "L" shaft

O 16 h6
20 11
with terminals smooth shaft 31 37,5

86 41,5 65
-0,029
-0,01
O 56 g6

26,5
CH 20
Albero tipo "P" CH 20 Versione Albero tipo "T" Linguetta 5x5x12

-0,029
-0,01
pinza ER20 con connettore albero con linguetta
M 25 x 1,5

O 56 g6
O 20

16

66

-0,011
M 16 x 1,5

+0
Type "P" shaft Version Type "T" shaft

O 23,5
O 16 h6
ER20 collet 27,5 37,5 118,5 29 70
with connector keyed shaft 15 20 11
46 37,5

25/07/2003 14/42
Elettromandrino taglia 55S-055 Size 55S-055 electro-spindle
Fissaggi standard disponibili Standard fixings available

N.B. N.B.
Il profilo della carcassa non rende Because of the body profile, the
disponibili le versioni con la foratura di versions with RH and LH side mounting
montaggio laterale Dx e laterale Sx. holes are not available.

19,5
55
22
= =
M 6 - n 4 fori

Fissaggio inferiore Bottom fixing

67

70

Come ordinare How to order Esempio di Example of a


compilazione ordine compiled order
Taglia attacco Potenza Velocit Curva Esecuzione Taglia attacco Potenza Velocit Curva Esecuzione
Fissaggio Fissaggio
elettromandrino utensile (kW) (rpm) tipo n elettromandrino utensile (kW) (rpm) tipo n
Electro-spindle tool Power Speed Curve Version Electro-spindle tool Power Speed Curve Version
Fixing Fixing
size type (kW) (rpm) type n size type (kW) (rpm) type n
____-___ _ _,__ _____ __ __ _ 55S-055 P 0,35 18000 57 1B 1

25/07/2003 15/42
Caratteristiche Elettriche Esecuzioni standard
Electrical specifications Standard versions
Elettromandrino Attacco utensile
Corrente nominale Curva di
380 V 220 V
Electro-spindle Tool type Nominal current potenza Tipo fissaggio
Kw rpm Power Morsettiera Connettore Morsettiera Connettore Fixing type
380V 220V curve Terminals Connector Terminals Connector

0,25 12000 1,0 A 1,8 A 56


0 = Speciale
Albero tipo "P" 0 = Specia
pinza ER20 0,35 18000 1,0 A 1,8 A 57
1 1A 1B 1C
Type "P" shaft 0,55 18000 1,6 A 2,8 A 58
1 = Inferiore
ER20 collet
1 = Bottom
0,55 24000 1,6 A 2,8 A 59

55S-055 0,25 12000 1,0 A 1,8 A 56


0 = Speciale
Albero tipo "L" 0 = Specia
2 Poli albero liscio 0,35 18000 1,0 A 1,8 A 57
1 1A 1B 1C
2 Poles Type "L" shaft 0,55 18000 1,6 A 2,8 A 58
1 = Inferiore
smooth shaft
1 = Bottom
0,55 24000 1,6 A 2,8 A 59

Albero tipo "T" 0,25 12000 1,0 A 1,8 A 56 0 = Speciale


albero con linguetta 0 = Specia
0,35 18000 1,0 A 1,8 A 57 1 1A 1B 1C
Type "T" shaft 1 = Inferiore
keyed shaft 0,55 18000 1,6 A 2,8 A 58 1 = Bottom

25/07/2003 16/42
Curve di potenza Power curves

400 400
350 350
300 300
potenza [W]

potenza [W]
250 250
200 200
150 150
100 100
50 50
0 0
6000 7000 8000 9000 10000 11000 12000 6000 8000 10000 12000 14000 16000 18000
rpm rpm

Curva di potenza 56 Power curve 56 Curva di potenza 57 Power curve 57


Velocit max = 12000 Max. speed = 12000 Velocit max = 18000 Max. speed = 18000
Vel. Nominale = 12000 Nominal speed = 12000 Vel. Nominale = 12000 Nominal speed = 12000

600
600
500
500

potenza [W]
400
potenza [W]

400
300 300

200 200

100 100

0 0
6000 8000 10000 12000 14000 16000 18000 6000 9000 12000 15000 18000 21000 24000
rpm rpm

Curva di potenza 58 Power curve 58 Curva di potenza 59 Power curve 59


Velocit max = 18000 Max. speed = 18000 Velocit max = 24000 Max. speed = 24000
Vel. Nominale = 18000 Nominal speed = 18000 Vel. Nominale = 18000 Nominal speed = 18000

25/07/2003 17/42
Elettromandrino taglia 55S-090 Size 55S-090 electro-spindle
Dimensioni di ingombro Overall dimensions

Velocit di rotazione Peso : ~ 4 kg Minimum rotation


minima 7000 rpm Weight : ~ 4 kg speed 7000 rpm

89,5 61 22 46

27
Versione Albero tipo "L" CH 20

-0,029
-0,01
con morsettiera albero liscio

O 23,5

M8

O 56 g6
-0,011
Version Type "L" shaft

+0
O 16 h6
with terminals smooth shaft 20 11
31 37,5

121 41,5 65
-0,029
-0,01
O 56 g6

26,5
CH 20
Albero tipo "P" CH 20
Versione Albero tipo "T" Linguetta 5x5x12

-0,029
-0,01
pinza ER20 con connettore albero con linguetta
M 25 x 1,5

O 56 g6
O 20
16

66

M 16 x 1,5

-0,011
Type "P" shaft Version Type "T" shaft

+0

O 23,5
ER20 collet with connector keyed shaft

O 16 h6
27,5 37,5 153,5 29 70

15 20 11
46 37,5

25/07/2003 18/42
Elettromandrino taglia 55S-090 Size 55S-090 electro-spindle
Fissaggi standard disponibili Standard fixings available

N.B. N.B.
Il profilo della carcassa non rende Because of the body profile, the

19,5
disponibili le versioni con la foratura di versions with RH and LH side mounting
montaggio laterale Dx e laterale Sx. holes are not available.

110
22
= =
M 6 - n 4 fori

Fissaggio inferiore Bottom fixing

67

82

Come ordinare How to order Esempio di Example of a


compilazione ordine compiled order
Taglia attacco Potenza Velocit Curva Esecuzione Taglia attacco Potenza Velocit Curva Esecuzione
Fissaggio Fissaggio
elettromandrino utensile (kW) (rpm) tipo n elettromandrino utensile (kW) (rpm) tipo n
Electro-spindle tool Power Speed Curve Version Electro-spindle tool Power Speed Curve Version
Fixing Fixing
size type (kW) (rpm) type n size type (kW) (rpm) type n
____-___ _ _,__ _____ __ __ _ 55S-090 P 0,5 18000 52 1B 1

25/07/2003 19/42
Caratteristiche Elettriche Esecuzioni standard
Electrical specifications Standard versions
Elettromandrino Attacco utensile
Corrente nominale Curva di
Nominal current potenza
380 V 220 V
Electro-spindle Tool type Tipo fissaggio
Power Morsettiera Connettore Morsettiera Connettore Fixing type
Kw rpm 380V 220V curve
Terminals Connector Terminals Connector

0,65 12000 1,8 A 3,2 A 51


0 = Speciale
Albero tipo "P" 0 = Special
pinza ER20 0,50 18000 1,5 A 2,6 A 52
1 1A 1B 1C
Type "P" shaft 1,00 18000 3,2 A 5,5 A 53
ER20 collet 1 = Inferiore
1 = Bottom
1,00 24000 3,2 A 5,5 A 54

55S-090 0,65 12000 1,8 A 3,2 A 51


0 = Speciale
Albero tipo "L" 0 = Special
2 Poli albero liscio 0,50 18000 1,5 A 2,6 A 52
1 1A 1B 1C
2 Poles Type "L" shaft 1,00 18000 3,2 A 5,5 A 53
smooth shaft 1 = Inferiore
1 = Bottom
1,00 24000 3,2 A 5,5 A 54

0,65 12000 1,8 A 3,2 A 51 0 = Speciale


Albero tipo "T"
0 = Special
albero con linguetta
0,50 18000 1,5 A 5,5 A 52 1 1A 1B 1C
Type "T" shaft
1 = Inferiore
keyed shaft 1 = Bottom
1,00 18000 3,2 A 5,5 A 53

25/07/2003 20/42
Curve di potenza Power curves

700 700
600 600
500 500
potenza [W]

potenza [W]
400 400
300 300
200 200
100 100
0 0
6000 7000 8000 9000 10000 11000 12000 6000 8000 10000 12000 14000 16000 18000
rpm rpm

Curva di potenza 51 Power curve 51 Curva di potenza 52 Power curve 52


Velocit max = 12000 Max. speed = 12000 Velocit max = 18000 Max. speed = 18000
Vel. Nominale = 12000 Nominal speed = 12000 Vel. Nominale = 12000 Nominal speed = 12000

1200
1200
1000
1000

potenza [W]
800
potenza [W]

800
600 600

400 400

200 200

0 0
6000 8000 10000 12000 14000 16000 18000 6000 9000 12000 15000 18000 21000 24000
rpm rpm

Curva di potenza 53 Power curve 53 Curva di potenza 54 Power curve 54


Velocit max = 18000 Max. speed = 18000 Velocit max = 24000 Max. speed = 24000
Vel. Nominale = 18000 Nominal speed = 18000 Vel. Nominale = 18000 Nominal speed = 18000

25/07/2003 21/42
Elettromandrino taglia 73-070 Size 73-070 electro-spindle
Dimensioni di ingombro Overall dimensions

Velocit di rotazione Peso : ~ 5 kg Minimum rotation


minima 7000 rpm Weight : ~ 5 kg speed 7000 rpm

40 90 25 76

-0,04
-0,01
40
Versione Albero tipo "L"

O 75 g7
con morsettiera albero liscio CH 20

O 23,5

M8
Version Type "L" shaft

-0,013
with terminals smooth shaft

+0
O 20 h6
20 11
31 48,5

103 41,5 65
-0,04
-0,01
O 75 g7

26,5
Albero tipo "P" Versione Albero tipo "T"
CH 20
CH 27 Linguetta 6x6x15

pinza ER25 con connettore albero con linguetta

-0,04
-0,01
M 32 x 1,5
O 25

O 75 g7
92,5
16

M 20 x 1,5

-0,013
Type "P" shaft Version Type "T" shaft

+0

O 23,5
O 20 h6
ER25 collet 29 48,5 144,5 36,5 82 with connector keyed shaft
15 20 11
46 48,5

25/07/2003 22/42
Elettromandrino taglia 73-070 Size 73-070 electro-spindle
Fissaggi standard disponibili Standard fixings available

37,5
Fissaggio inferiore
Bottom fixing

90
30
= =
M 6 - n 4 fori

Fissaggio laterale Dx Fissaggio laterale Sx


RH side fixing LH side fixing

40
40

93
= =

= =
M 6 - n 4 fori M 6 - n 4 fori
37,5 90 82 90 37,5

Come ordinare How to order Esempio di Example of a


compilazione ordine compiled order
Taglia attacco Potenza Velocit Curva Esecuzione Taglia attacco Potenza Velocit Curva Esecuzione
Fissaggio Fissaggio
elettromandrino utensile (kW) (rpm) tipo n elettromandrino utensile (kW) (rpm) tipo n
Electro-spindle tool Power Speed Curve Version Electro-spindle tool Power Speed Curve Version
Fixing Fixing
size type (kW) (rpm) type n size type (kW) (rpm) type n
____-___ _ _,__ _____ __ __ _ 73-070 P 1 18000 72 1B 1
25/07/2003 23/42
Caratteristiche Elettriche Esecuzioni standard
Electrical specifications Standard versions
Elettromandrino Attacco utensile
Corrente nominale Curva di
Nominal current 380 V 220 V
potenza Tipo Fixing
Electro-spindle Tool type Kw rpm Power Morsettiera Connettore Morsettiera Connettore fissaggio type
380V 220V curve Terminals Connector Terminals Connector
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
1,30 12000 3,2 A 5,3 A 71 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "P" 1 = Inferiore 1 = Bottom
pinza ER25 1,00 18000 2,5 A 4,1 A 72 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Type "P" shaft 2,00 18000 5,1 A 8,8 A 73 1 1A 1B 1C 1 = Inferiore 1 = Bottom
2 = Laterale Dx 2 = RH side
ER25 collet 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
2,00 24000 5,1 A 8,8 A 74 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
1,30 12000 3,2 A 5,3 A 71 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
73-070 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "L" 1 = Inferiore 1 = Bottom
2 Poli albero liscio 1,00 18000 2,5 A 4,1 A 72 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
2 Poles Type "L" shaft 1 = Inferiore 1 = Bottom
2,00 18000 5,1 A 8,8 A 73 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
smooth shaft 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
2,00 24000 5,1 A 8,8 A 74 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
Albero tipo "T" 1,30 12000 3,2 A 5,3 A 71 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
albero con 0 = Speciale 0 = Special
linguetta 1 = Inferiore 1 = Bottom
1,00 18000 2,5 A 4,1 A 72 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
Type "T" shaft 0 = Speciale 0 = Special
keyed shaft 2,00 18000 5,1 A 8,8 A 73 1 1A 1B 1C 1 = Inferiore 1 = Bottom
2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side

25/07/2003 24/42
Curve di potenza Power curves

1400 1400
1200 1200
1000 1000
potenza [W]

potenza [W]
800 800
600 600
400 400
200 200
0 0
6000 7000 8000 9000 10000 11000 12000 6000 8000 10000 12000 14000 16000 18000
rpm rpm

Curva di potenza 71 Power curve 71 Curva di potenza 72 Power curve 72


Velocit max = 12000 Max. speed = 12000 Velocit max = 18000 Max. speed = 18000
Vel. Nominale = 12000 Nominal speed = 12000 Vel. Nominale = 12000 Nominal speed = 12000

2500
2500
2000
2000

potenza [W]
potenza [W]

1500 1500

1000 1000

500 500

0 0
6000 8000 10000 12000 14000 16000 18000 6000 9000 12000 15000 18000 21000 24000
rpm rpm

Curva di potenza 73 Power curve 73 Curva di potenza 74 Power curve 74


Velocit max = 18000 Max. speed = 18000 Velocit max = 24000 Max. speed = 24000
Vel. Nominale = 18000 Nominal speed = 18000 Vel. Nominale = 18000 Nominal speed = 18000

25/07/2003 25/42
Elettromandrino taglia 73-140 Size 73-140 electro-spindle
Dimensioni di ingombro Overall dimensions

Velocit di rotazione Peso : ~ 7 kg Minimum rotation


minima 7000 rpm Weight : ~ 7 kg speed 7000 rpm

110 90 25 76

-0,04
-0,01
O 75 g7
40
Versione Albero tipo "L" CH 20
con morsettiera albero liscio

O 23,5

M8
Version Type "L" shaft

-0,013
+0
with terminals smooth shaft

O 20 h6
20 11
31 48,5

173 41,5 65
-0,04
-0,01
O 75 g7

26,5
CH 20
Albero tipo "P" CH 27 Versione Albero tipo "T" Linguetta 6x6x15

-0,04
-0,01
pinza ER25 con connettore albero con linguetta
M 32 x 1,5

O 25

O 75 g7
92,5
16

-0,013
M 20 x 1,5
Type "P" shaft Version Type "T" shaft

+0
O 20 h6

O 23,5
ER25 collet 29 48,5 214,5 36,5 82
with connector keyed shaft
15 20 11
46 48,5

25/07/2003 26/42
Elettromandrino taglia 73-140 Size 73-140 electro-spindle
Fissaggi standard disponibili Standard fixings available

37,5
Fissaggio inferiore
Bottom fixing

90
30
= =
M 6 - n 4 fori

Fissaggio laterale Dx Fissaggio laterale Sx


RH side fixing LH side fixing

40
40

93
= =

= =
M 6 - n 4 fori M 6 - n 4 fori
37,5 90 82 90 37,5

Come ordinare How to order Esempio di Example of a


compilazione ordine compiled order
Taglia attacco Potenza Velocit Curva Esecuzione Taglia attacco Potenza Velocit Curva Esecuzione
Fissaggio Fissaggio
elettromandrino utensile (kW) (rpm) tipo n elettromandrino utensile (kW) (rpm) tipo n
Electro-spindle tool Power Speed Curve Version Electro-spindle tool Power Speed Curve Version
Fixing Fixing
size type (kW) (rpm) type n size type (kW) (rpm) type n
____-___ _ _,__ _____ __ __ _ 73-140 P 2,2 18000 77 1B 1
25/07/2003 27/42
Caratteristiche Elettriche Esecuzioni standard
Electrical specifications Standard versions
Elettromandrino Attacco utensile
Corrente nominale Curva di
Nominal current 380 V 220 V
potenza Tipo Fixing
Electro-spindle Tool type Kw rpm Power Morsettiera Connettore Morsettiera Connettore fissaggio type
380V 220V curve Terminals Connector Terminals Connector
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
2,40 12000 5,5 A 9,7 A 76 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "P" 1 = Inferiore 1 = Bottom
pinza ER25 2,20 18000 5,0 A 8,8 A 77 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Type "P" shaft 3,50 18000 8,8 A 15,3 A 78 1 1A 1B 1C 1 = Inferiore 1 = Bottom
2 = Laterale Dx 2 = RH side
ER25 collet 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
3,40 24000 8,1 A 15 A 79 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
2,40 12000 5,5 A 9,7 A 76 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
73-140 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "L" 1 = Inferiore 1 = Bottom
2 Poli albero liscio 2,20 18000 5,0 A 8,8 A 77 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
2 Poles Type "L" shaft 1 = Inferiore 1 = Bottom
3,50 18000 8,8 A 15,3 A 78 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
smooth shaft 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
3,40 24000 8,1 A 15 A 79 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
Albero tipo "T" 2,40 12000 5,5 A 9,7 A 76 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
albero con 0 = Speciale 0 = Special
linguetta 1 = Inferiore 1 = Bottom
2,20 18000 5,0 A 8,8 A 77 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
Type "T" shaft 0 = Speciale 0 = Special
keyed shaft 3,50 18000 8,8 A 15,3 A 78 1 1A 1B 1C 1 = Inferiore 1 = Bottom
2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side

25/07/2003 28/42
Curve di potenza Power curves

3000 3000
2500 2500
potenza [W]

potenza [W]
2000 2000
1500 1500
1000 1000
500 500
0 0
6000 7000 8000 9000 10000 11000 12000 6000 8000 10000 12000 14000 16000 18000
rpm rpm

Curva di potenza 76 Power curve 76 Curva di potenza 77 Power curve 77


Velocit max = 12000 Max. speed = 12000 Velocit max = 18000 Max. speed = 18000
Vel. Nominale = 12000 Nominal speed = 12000 Vel. Nominale = 12000 Nominal speed = 12000

4000
4000
3500
3500
3000
3000

potenza [W]
potenza [W]

2500 2500
2000 2000
1500 1500
1000 1000
500 500
0 0
6000 8000 10000 12000 14000 16000 18000 6000 9000 12000 15000 18000 21000 24000
rpm rpm

Curva di potenza 78 Power curve 78 Curva di potenza 79 Power curve 79


Velocit max = 18000 Max. speed = 18000 Velocit max = 24000 Max. speed = 24000
Vel. Nominale = 18000 Nominal speed = 18000 Vel. Nominale = 18000 Nominal speed = 18000

25/07/2003 29/42
Elettromandrino taglia 90-100 Size 90-100 electro-spindle
Dimensioni di ingombro Overall dimensions

Velocit di rotazione Peso : ~ 7 kg Minimum rotation


minima 7000 rpm Weight : ~ 7 kg speed 7000 rpm

80 90 25 76

-0,047
-0,012
O 85 g7
40
Versione Albero tipo "L"
CH 32
con morsettiera albero liscio

O 37

M8
Version Type "L" shaft

-0,016
+0
with terminals smooth shaft

O 30 h6
48,5 12,5
61 56,5

142 41,5 65 CH 32
-0,047
-0,012

Linguetta 8x7x45

-0,047
-0,012
O 85 g7

26,5

O 85 g7
Albero tipo "P" CH 32 Versione Albero tipo "T"

-0,016
M 25 x 1,5

+0
pinza ER32 con connettore albero con linguetta
M 40 x 1,5

O 37
O 30 h6
O 32

120
16

Type "P" shaft Version Type "T" shaft 16 48,5 12,5


ER32 collet 83
with connector keyed shaft 77 56,5
35 56,5 193 46

25/07/2003 30/42
Elettromandrino taglia 90-100 Size 90-100 electro-spindle
Fissaggi standard disponibili Standard fixings available

39
Fissaggio inferiore

60
Bottom fixing
36

60
= =
M 8 - n 6 fori

Fissaggio laterale Dx Fissaggio laterale Sx


RH side fixing LH side fixing

60
60

120
= =

= =
M8 M8
n 6 fori 103 n 6 fori
39 60 60 60 60 39

Come ordinare How to order Esempio di Example of a


compilazione ordine compiled order
Taglia attacco Potenza Velocit Curva Esecuzione Taglia attacco Potenza Velocit Curva Esecuzione
Fissaggio Fissaggio
elettromandrino utensile (kW) (rpm) tipo n elettromandrino utensile (kW) (rpm) tipo n
Electro-spindle tool Power Speed Curve Version Electro-spindle tool Power Speed Curve Version
Fixing Fixing
size type (kW) (rpm) type n size type (kW) (rpm) type n
____-___ _ _,__ _____ __ __ _ 90-100 P 3 18000 92 1B 1
25/07/2003 31/42
Caratteristiche Elettriche Esecuzioni standard
Electrical specifications Standard versions
Elettromandrino Attacco utensile
Corrente nominale Curva di
Nominal current 380 V 220 V
potenza Tipo Fixing
Electro-spindle Tool type Kw rpm Power Morsettiera Connettore Morsettiera Connettore fissaggio type
380V 220V curve Terminals Connector Terminals Connector
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
3,50 12000 8,4 A 14,3 A 91 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "P" 1 = Inferiore 1 = Bottom
pinza ER25 3,00 18000 8,0 A 13,5 A 92 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Type "P" shaft 4,50 18000 9,5 A 16,4 A 93 1 1A 1B 1C 1 = Inferiore 1 = Bottom
2 = Laterale Dx 2 = RH side
ER25 collet 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
4,20 24000 9,0 A 16,0 A 94 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
3,50 12000 8,4 A 14,3 A 91 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
90-100 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "L" 1 = Inferiore 1 = Bottom
2 Poli albero liscio 3,00 18000 8,0 A 13,5 A 92 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
2 Poles Type "L" shaft 1 = Inferiore 1 = Bottom
4,50 18000 9,5 A 16,4 A 93 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
smooth shaft 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
4,20 24000 9,0 A 16,0 A 94 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
Albero tipo "T" 3,50 12000 8,4 A 14,3 A 91 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
albero con 0 = Speciale 0 = Special
linguetta 1 = Inferiore 1 = Bottom
3,00 18000 8,0 A 13,5 A 92 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
Type "T" shaft 0 = Speciale 0 = Special
keyed shaft 4,50 18000 9,5 A 16,4 A 93 1 1A 1B 1C 1 = Inferiore 1 = Bottom
2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side

25/07/2003 32/42
Curve di potenza Power curves

4000 4000
3500 3500
3000 3000
potenza [W]

potenza [W]
2500 2500
2000 2000
1500 1500
1000 1000
500 500
0 0
6000 7000 8000 9000 10000 11000 12000 6000 8000 10000 12000 14000 16000 18000
rpm rpm

Curva di potenza 91 Power curve 91 Curva di potenza 92 Power curve 92


Velocit max = 12000 Max. speed = 12000 Velocit max = 18000 Max. speed = 18000
Vel. Nominale = 12000 Nominal speed = 12000 Vel. Nominale = 12000 Nominal speed = 12000

5000
5000
4000
4000

potenza [W]
potenza [W]

3000 3000

2000 2000

1000 1000

0 0
6000 8000 10000 12000 14000 16000 18000 6000 9000 12000 15000 18000 21000 24000
rpm rpm

Curva di potenza 93 Power curve 93 Curva di potenza 94 Power curve 94


Velocit max = 18000 Max. speed = 18000 Velocit max = 24000 Max. speed = 24000
Vel. Nominale = 18000 Nominal speed = 18000 Vel. Nominale = 18000 Nominal speed = 18000

25/07/2003 33/42
Elettromandrino taglia 90-140 Size 90-140 electro-spindle
Dimensioni di ingombro Overall dimensions

Velocit di rotazione Peso : ~ 10 kg Minimum rotation


minima 7000 rpm Weight : ~ 10 kg speed 7000 rpm

120 90 25 76

-0,047
-0,012
40
Versione Albero tipo "L"

O 85 g7
con morsettiera albero liscio CH 32

O 37

M8
Version Type "L" shaft

-0,016
with terminals smooth shaft

+0
O 30 h6
48,5 12,5
61 56,5
-0,047
-0,012

182 41,5 65
O 85 g7

26,5
Albero tipo "P" CH 32
Versione Albero tipo "T"
CH 32
pinza ER32 con connettore albero con linguetta Linguetta 8x7x45
M 40 x 1,5

-0,047
-0,012
O 32

120
16

O 85 g7
Type "P" shaft Version Type "T" shaft

-0,016
M 25 x 1,5

+0
ER32 collet with connector keyed shaft

O 37
O 30 h6
35 56,5 233 46 83

16 48,5 12,5
77 56,5

25/07/2003 34/42
Elettromandrino taglia 90-140 Size 90-140 electro-spindle
Fissaggi standard disponibili Standard fixings available

39
Fissaggio inferiore
Bottom fixing

60
36

60
= =
M 8 - n 6 fori

Fissaggio laterale Dx Fissaggio laterale Sx


RH side fixing LH side fixing

60
60

120
= =

= =
M8 M8
n 6 fori 103 n 6 fori
39 60 60 60 60 39

Come ordinare How to order Esempio di Example of a


compilazione ordine compiled order
Taglia attacco Potenza Velocit Curva Esecuzione Taglia attacco Potenza Velocit Curva Esecuzione
Fissaggio Fissaggio
elettromandrino utensile (kW) (rpm) tipo n elettromandrino utensile (kW) (rpm) tipo n
Electro-spindle tool Power Speed Curve Version Electro-spindle tool Power Speed Curve Version
Fixing Fixing
size type (kW) (rpm) type n size type (kW) (rpm) type n
____-___ _ _,__ _____ __ __ _ 90-140 P 4,5 18000 97 1B 1

25/07/2003 35/42
Caratteristiche Elettriche Esecuzioni standard
Electrical specifications Standard versions
Elettromandrino Attacco utensile
Corrente nominale Curva di
Nominal current 380 V 220 V
potenza Tipo Fixing
Electro-spindle Tool type Kw rpm Power Morsettiera Connettore Morsettiera Connettore fissaggio type
380V 220V curve Terminals Connector Terminals Connector
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
5,00 12000 10,0 A 17,0 A 96 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "P" 1 = Inferiore 1 = Bottom
pinza ER32 4,50 18000 9,5 A 16,0 A 97 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Type "P" shaft 6,00 18000 12,6 A 22,0 A 98 1 1A 1B
Non disponibile 1 = Inferiore 1 = Bottom
Not availlable 2 = Laterale Dx 2 = RH side
ER32 collet 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Non disponibile 1 = Inferiore 1 = Bottom
5,50 24000 12,0 A 20,0 A 99 1 1A 1B Not availlable 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
5,00 12000 10,0 A 17,0 A 96 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
90-140 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Albero tipo "L" 1 = Inferiore 1 = Bottom
2 Poli albero liscio 4,50 18000 9,5 A 16,0 A 97 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
2 Poles Type "L" shaft Non disponibile 1 = Inferiore 1 = Bottom
6,00 18000 12,6 A 22,0 A 98 1 1A 1B Not availlable 2 = Laterale Dx 2 = RH side
smooth shaft 3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
Non disponibile 1 = Inferiore 1 = Bottom
5,50 24000 12,0 A 20,0 A 99 1 1A 1B Not availlable 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
0 = Speciale 0 = Special
1 = Inferiore 1 = Bottom
Albero tipo "T" 5,00 12000 10,0 A 17,0 A 96 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
albero con 0 = Speciale 0 = Special
linguetta 1 = Inferiore 1 = Bottom
4,50 18000 9,5 A 16,0 A 97 1 1A 1B 1C 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side
Type "T" shaft 0 = Speciale 0 = Special
keyed shaft 6,00 18000 12,6 A 22,0 A 98 1 1A 1B
Non disponibile 1 = Inferiore 1 = Bottom
Not availlable 2 = Laterale Dx 2 = RH side
3 = Laterale Sx 3 = LH side

25/07/2003 36/42
Curve di potenza Power curves

6000 6000
5000 5000
potenza [W]

potenza [W]
4000 4000
3000 3000
2000 2000
1000 1000
0 0
6000 7000 8000 9000 10000 11000 12000 6000 8000 10000 12000 14000 16000 18000
rpm rpm

Curva di potenza 96 Power curve 96 Curva di potenza 97 Power curve 97


Velocit max = 12000 Max. speed = 12000 Velocit max = 18000 Max. speed = 18000
Vel. Nominale = 12000 Nominal speed = 12000 Vel. Nominale = 12000 Nominal speed = 12000

7000
7000
6000
6000
5000

potenza [W]
5000
potenza [W]

4000 4000

3000 3000
2000 2000
1000 1000
0 0
6000 8000 10000 12000 14000 16000 18000 6000 9000 12000 15000 18000 21000 24000
rpm rpm

Curva di potenza 98 Power curve 98 Curva di potenza 99 Power curve 99


Velocit max = 18000 Max. speed = 18000 Velocit max = 24000 Max. speed = 24000
Vel. Nominale = 18000 Nominal speed = 18000 Vel. Nominale = 18000 Nominal speed = 18000

25/07/2003 37/42
Elettromandrino taglia 120-170 Size 120-170 electro-spindle
Dimensioni di ingombro Overall dimensions
Velocit di rotazione minima 3000 rpm Minimum rotation speed 3000 rpm
per V max = 6000 rpm Peso : ~ 30 kg for V max = 6000 rpm
Velocit di rotazione minima 7000 rpm Weight : ~ 30 kg Minimum rotation speed 7000 rpm
per V max = 18000 rpm for V max = 18000 rpm

50 75 47 72

34,5
Albero tipo "P" Versione
-0,054
-0,014

M 50 x 1,5

pinza ER40 con connettore


O 40

145
O 120 g7

Type "P" shaft Version


ER40 collet with connector

38 61,5 300 55 175


-0,054
-0,014

50 75 47
72
O 120 g7

34,5
Linguetta 10x8x56
Albero tipo "T" Versione
albero con linguetta con connettore

145
Type "T" shaft Version
with connector
M 30 x 2

keyed shaft
-0,016
+0
O 40 h6

22 58

80 55 300 55 175
25/07/2003 38/42
Elettromandrino taglia 120-170 Size 120-170 electro-spindle
Fissaggi standard disponibili Standard fixings available

20
N.B. N.B.
Il profilo della carcassa non rende Because of the body profile, the
M 12 - n4 fori version with LH side mounting
disponibili la versione con la foratura di
montaggio laterale Sx. 140
= =
holes is not available.

265
Fissaggio inferiore
Bottom fixing

Fissaggio laterale DX
RH side fixing
70

145
= =

M 12 - n4 fori 176
15 270

Come ordinare How to order Esempio di Example of a


compilazione ordine compiled order
Taglia attacco Potenza Velocit Curva Esecuzione Taglia attacco Potenza Velocit Curva Esecuzione
Fissaggio Fissaggio
elettromandrino utensile (kW) (rpm) tipo n elettromandrino utensile (kW) (rpm) tipo n
Electro-spindle tool Power Speed Curve Version Electro-spindle tool Power Speed Curve Version
Fixing Fixing
size type (kW) (rpm) type n size type (kW) (rpm) type n
____-___ _ _,__ _____ __ __ _ 120-170 P 8,1 6000 121 1A 1

25/07/2003 39/42
Caratteristiche Elettriche Esecuzioni standard
Electrical specifications Standard versions
Elettromandrino Attacco utensile
Corrente nominale Curva di
Nominal current potenza 380 V 220 V
Tipo Fixing
Electro-spindle Tool type Kw rpm Power Morsettiera Connettore Morsettiera Connettore fissaggio type
380V 220V curve Terminals Connector Terminals Connector
Non
0 = Speciale 0 = Special
Albero tipo "P" 13,5 12000 31,0A
disponibile
122 1 1A Non disponibile Non disponibile
1 = Inferiore 1 = Bottom
Not Not availlable Not availlable
pinza ER40 availlable
2 = Laterale Dx 2 = RH side
120-170 Non
Type "P" shaft disponibile Non disponibile Non disponibile
0 = Speciale 0 = Special
ER40 collet 12,0 18000 31,0A Not 122 1 1A Not availlable Not availlable
1 = Inferiore 1 = Bottom
2 = Laterale Dx 2 = RH side
4 Poli availlable
Albero tipo "T"
Non
4 Poles albero con linguetta disponibile Non disponibile Non disponibile
0 = Speciale 0 = Special
8,10 6000 19,5A Not 121 1 1A Not availlable Not availlable
1 = Inferiore 1 = Bottom
Type "T" shaft availlable
2 = Laterale Dx 2 = RH side
keyed shaft

25/07/2003 40/42
Curve di potenza Power curves

16000
9000
14000
8000
7000 12000

potenza [W]
potenza [W]

6000 10000
5000 8000
4000
6000
3000
4000
2000
1000 2000
0 0
3000 4000 5000 6000 6000 8000 10000 12000 14000 16000 18000
rpm rpm

Curva di potenza 121 Power curve 121 Curva di potenza 122 Power curve 122
Velocit max = 6000 Max. speed = 6000 Velocit max = 18000 Max. speed = 18000
Vel. Nominale = 6000 Nominal speed = 6000 Vel. Nominale = 12000 Nominal speed = 12000

25/07/2003 41/42
==

42/42

Potrebbero piacerti anche