- DocumentoNATE Module 1_Week1caricato daParag Naik
- DocumentoFrequently Asked Questions and Answers Emc 2017-Updatedcaricato daParag Naik
- Documentopuzyrewski2003caricato daParag Naik
- Documentoarticle1380788838_Ali et al.pdfcaricato daParag Naik
- Documento17-4-phcaricato daParag Naik
- DocumentoF02_3caricato daParag Naik
- DocumentoA Look at Compressor Impeller Technologies for Turbochargers Focusingon Surge Mitigation 2229 8711 1000185caricato daParag Naik
- Documento223caricato daParag Naik
- DocumentoAreas of Specializations 090418caricato daParag Naik
- DocumentoCommand Stylecaricato daParag Naik
- DocumentoAssess Score Evaluatecaricato daParag Naik
- Documento10 Evidence Based Principles of Effective Teaching Rsearchcaricato daParag Naik
- DocumentoAnalysis of a Shrink-fit Failure on a Gear Hub Shaft Assemblycaricato daParag Naik
- Documento9979726-Vibrations-of-Shells-and-Plates.pdfcaricato daParag Naik
- DocumentoOlofsson_2015_IOP_Conf._Ser.%3A_Mater._Sci._Eng._84_012026 (1)caricato daParag Naik
- Documentogao2006_2.pdfcaricato daParag Naik
- DocumentoCoupled Vibration and Naturalcaricato daParag Naik
- DocumentoCampbell Diagram Chart Results.docxcaricato daParag Naik
- DocumentoCampbell Diagram Chart Results.docxcaricato daParag Naik
- DocumentoStudy on Damping Control for Vibration Isolation Andcaricato daParag Naik
- DocumentoIJSETR-VOL-3-ISSUE-1-100-106.pdfcaricato daParag Naik
- Documento01FE16MMD011_Paragpushp Naik_FEMD assignment.xlsxcaricato daParag Naik
- DocumentoVibration assignment_01F16MMD011_Naik Paragpushp.docxcaricato daParag Naik
- DocumentoVibration assignment_01F16MMD011_Naik Paragpushp.docxcaricato daParag Naik
- DocumentoA THERMOELASTIC ANALYSIS of SHRINK-FIT TYPE Constructions by Boundaary Element Methodcaricato daParag Naik
- Documentospr Technical Information 4.pdfcaricato daParag Naik
- DocumentoMechanical Drawing Standards and Tables.pdfcaricato daParag Naik
- DocumentoContact Problem of Disk on Shaft Fixed by Induction Shrink Fit.pdfcaricato daParag Naik
- DocumentoAnalysis of Elastic-plastic Interference-fit Jointscaricato daParag Naik
- Documentoekhteraeitoussi2012caricato daParag Naik
- DocumentoIMECS2016_pp694-698caricato daParag Naik
- DocumentoModeling Component Assembly of a Bearing Using Abaqus.pdfcaricato daParag Naik
- Documento14. Separation Frequency Analysis of Interference Fitted Hollow Shaft–Hub Connections by Finite Element Methodcaricato daParag Naik
- DocumentoOn Shrink Fit Analysis and Designcaricato daParag Naik
- DocumentoModeling Component Assembly of a Bearing Using Abaquscaricato daParag Naik
- Documento19. Autofrettage of thick cylinders.pdfcaricato daParag Naik
- Documento9.A general autofrettage model of a thick-walled.pdfcaricato daParag Naik
- Documento9.a General Autofrettage Model of a Thick-walledcaricato daParag Naik
- Documento12. Autofrettage process analysis of a compound cylinder based on the elastic-perfectly.pdfcaricato daParag Naik
- Documento12. Autofrettage Process Analysis of a Compound Cylinder Based on the Elastic-perfectlycaricato daParag Naik
- Documento18. Determination of Residual Stress Distributions Incaricato daParag Naik
- Documento2. Simulation of Removing Autofrettage-Induced Residualcaricato daParag Naik
- Documento1.Optimum autofrettage pressure in thick cylinders.pdfcaricato daParag Naik
- Documento11. Residual Stress Analysis of an Autofrettagedcaricato daParag Naik
- Documento10. Actual Unloading Behavior and Its.pdfcaricato daParag Naik
- DocumentoDesign and Analysis on Interference Fit in the Hardwood Dowelglued.pdfcaricato daParag Naik
- DocumentoContact Problem of Disk on Shaft Fixed by Induction Shrink Fit.pdfcaricato daParag Naik
- Documento[3] Stress analysis of shrink-fitted joints for various fit forms via finite element method.pdfcaricato daParag Naik
- Documento[7] Finite Element Analysis of Optimized Compound Cylindercaricato daParag Naik