Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
ZTE University
Content
Overview NodeB Configuration Ground Resource Configuration Transmission Resource Configuration Wireless Resource Configuration
On-line configuration This mode is to configure the ZDB of the B8200 directly. The data configured on the line take effect immediately. To configure on the line, modify the contents in the C:\ump file first, to set the IP address as the IP address of the debugging network interface on the CC board of the B8200. Then, run the LMT. The CC board is defaulted before delivery. Off-line configuration This mode is to modify the configurations on the client. The configurations are saved into the designated directory in the mode of the XML file. In the off-line configuration, the LMT is not connected to the B8200 and the operation does not affect the running of the B8200. The off-line configuration mode is used when there is no ump file under the root directory of the Disc C. One local configuration file is required for the off-line configuration.
IPOE
PCH FP
RACH FP
FACH FP
DSCH FP
USCH FP
CPCH FP
DCH FP
Transport Layer
Content
LMT Data Configuration NodeB Configuration Ground Resource Configuration Transmission Resource Configuration Wireless Resource Configuration
NodeB Configuration
NodeB Basic Attributes Clock Reference Source Configuring Rack and Board
NodeB Configuration
Setting NodeB Basic Attributes :Basic Parameter and Other Relevant Parameters
NodeB Configuration
NodeB Configuration
NodeB Configuration
NodeB Configuration
Configuring Rack and Board : Create board on BBU and RRU rack
NodeB Configuration
Configuring Rack and Board : Create board on BBU and RRU rack
NodeB Configuration
Configuring Clock Reference Source : Right-click and choose Configuration Management BS Configure Clock Reference Source. Configure Clock Reference Source dialog box pops up.
Content
LMT Data Configuration NodeB Configuration Ground Resource Configuration Transmission Resource Configuration Wireless Resource Configuration
Environment Monitoring In-line Tower Amplifier Serial Port Topology structure AISG Device Dry Contact
Configuring Environment Monitoring: click Configuration Management Ground Resource Management Environment Monitoring to open the Environment Monitoring window:
Configuring Topology Structure: Click Configuration Management Ground Resource Management Topology to open the Topology window.
The board/rack near the baseband processing unit is the upper-level The board/rack away from the baseband processing unit is lower-level.
Content
LMT Data Configuration NodeB Configuration Ground Resource Configuration Transmission Resource Configuration Wireless Resource Configuration
For the IP over FE transmission, the following nine items should be configured:
Ethernet Parameter Global Port Parameter IP Parameter Static Route Parameter SCTP Parameter SCTP Stream Parameter IP Clock Parameter BFD Parameter OMC-B Parameter
Configuring Ethernet Parameter--Click Physical Media Configuration Ethernet parameter .Right-click the blank part in this pane and choose Add to open the Ethernet parameter management dialog box:
Configuring Global Port Parameter--Click Transmission Resource Management IP Bearing Configuration Global port parameter to open the Global port parameter pane. Right-click the blank part in this pane and choose Add to open the Global Port Parameter dialog box:
Configuring IP Parameter--Click Transmission Resource Management IP Bearing Configuration IP parameter to open the IP parameter pane. Rightclick the blank part in this pane and choose Add to open the IP Parameter Management dialog box:
Configuring Static Route Parameter--Click Transmission Resource Management IP Bearing Configuration Static Router Parameter. Rightclick the blank part in the right pane and choose Add to open the Static route configuration dialog box.
Configuring SCTP Parameter--Click Transmission Resource Management IP Bearing Configuration SCTP Parameter to open the SCTP parameter pane. Right-click the blank part in this pane and choose Add to open the SCTP parameter management dialog box:
Configuring SCTP Stream Parameter--Click Transmission Resource Management IP Bearing Configuration SCTP Stream Parameter to open the SCTP stream parameter pane. Right-click the blank part in this pane and choose Add to open the SCTP stream parameter management dialog box.
Configuring IP Clock Parameter--Click Transmission Resource Management IP Bearing Configuration IP Clock Parameter to open the IP Clock parameter pane. Right-click the blank part in this pane and choose Add to open the IP Clock parameter dialog box.
Configuring BFD Parameter--Click Transmission Resource Management IP Bearing Configuration BFD Parameter to open the BFD parameter pane. Right-click the blank part in this pane and choose Add to open the BFD parameter dialog box.
Content
LMT Data Configuration NodeB Configuration Ground Resource Configuration Transmission Resource Configuration Wireless Resource Configuration
RF Connection RRU Common Parameter Base Band Resource Pool WCDMA Sector Local Cell
Configuring RF Connection--Click Wireless Resource Management RF Connection to open the RF Connection pane. Right-click the blank part in this pane and choose Add Rack to open the RF Connection dialog box.
Configuring RRU Common Parameter --Click Wireless Resource Management RRU Common Parameter to open the RRU Common Parameter pane. Right-click the blank part in this pane and choose Add to open the RRU Common Parameter dialog box.
Configuring Baseband resource pool--Click Wireless Resource Management Baseband Resource Pool and right-click the blank part in this pane and choose Add to open the baseband resource pool Management dialog box:
Configuring Baseband resource--Click Baseband Resource Pool Baseband Resource to open the Baseband Resource pane. Right-click the blank part in this pane and choose Add to open the Baseband Resource dialog box:
Configuring WCDMA Sector--Click Wireless Resource Management WCDMA Sector to open the WCDMA Sector pane. Right-click the blank part in this pane and choose Add to open the WCDMA Sector dialog box:
Configuring Local cell--Click Wireless Resource Management WCDMA Sector to open the WCDMA Sector pane. Right-click the blank part in this pane and choose Add Local Cell to open the Local Cell Management dialog box: