Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Features:
AAU RRU
• The fronthaul fiber between the AAU/RRU
BBU power
2. Fronthaul fiber between the AAU/RRU and
supply solution
the BBU:
80% within 10 km.
Fronthaul 20% ranges from 10 km to 20 km.
link
BBU
3. Application:
Japan SoftBank (with USUs)
BBU5900
BBU5900 Power Module
BBU5900 Fan Module
A. Purpose E. Appearance
Converts –48 V DC power into +12 V DC power.
(+12 V supplies power to the service boards through the backplane. The fan module is not supported by 12 V power
supply.)
Provides two ports transmitting RS485 signals and eight ports transmitting Boolean signals.
(Boolean alarm signal inputs support only dry contacts and Open Collector (OC) inputs.)
(Boolean alarm signals are transmitted to the main control board through the backplane and then reported to the EMS.)
B. Composition
One branch power cable
power modules.
One UPEUe is configured with one power cable.
Two UPEUes are configured with two power cables. (1) EPC4 connector
(1) HDEPC
(2) Scale line
Length: Maximum 20 m. It is recommended that the connector
(3) Sliders
(2) Slider
length be within 6 m. (4) Hole for the
(3) Terminal
conductor
D. Technical Specifications
BBU5900 Power Cable Introduction (English) HDEPC Installation Guide (English) EPC4 Installation Guide (English)
A. Purpose E. Appearance
The FANf module performs the following functions:
• Dissipates heat for other boards in the BBU.
• Controls the speed of fans, monitors the temperature of fans, and
reports the status, temperature, and in-position signals of fans.
• Provides a read/write electronic label.
C. Configuration Principle
The BBU5900 is delivered with one FANf by default.
A. Purpose
Provides 10 DC power outputs. DC input terminals NEG(-) Two M6 one-hole OT terminals.
The output voltage is equal to RTN(+) Maximum:
the input voltage. • One pair of 35 mm 2 cables.
• Two pairs of 25 mm 2 cables.
DC output terminal LOAD0 ~ Uses EPC5 connector. Single through-current
B. Composition LOAD5 Supports cables with the cross- capability is 30 A
DCDU12B case 2 2
sectional area of 3.3 mm to 10 mm . (derated). 25 A is used.
DCDU12B input power cable
Six EPC5 connectors (delivered by DC output terminal LOAD0 ~ Uses EPC4 connector. Single through-current
default) LOAD9 Supports cables with cross-sectional capability is 30 A
Four EPC5 connectors (delivered by area of 1.5 mm2 to 4 mm2. (derated). 25 A is used.
default)
DCDU12B ground cable EPC5 connector EPC4 connector
D. Technical Specifications
DCDU12B Introduction (English)
E. Appearance
B. Composition E. Appearance
Up converter case (EPU02D-02)
Two up converters (BDU65-03)
One management module (PMU12A)
One monitoring cable (included)
C. Configuration Principles
Length of the input power cable: 12 m by default.
(1) EPU02D series subrack
Types of ground cables: Determined based on the region. (2) BDU65-03
Length of the ground cable: 2 m by default. (3) PMU 12 A
UPEU
UPEU
UPEU
UPEU
Important notes: The external frames of EPU02D and EPU02D-02 are the same, but the two sets of equipment are different. For details, see
http://support.huawei.com.
HUAWEI TECHNOLOGIES CO., LTD. Huawei confidential. Page 15
EPU02D-02 Monitoring Signal Cable
E. Appearance
A. Purpose
Reports the environment variables and alarm parameters of
the EPU02D-02 to the BBU5900 power module (UPEUe).
(1) RJ45 connector
The environment variables of the EPU02D-02 are output by
the COM port of the PMU12A. X1 End X2 End Wire Type
The PMU12A alarm uses the RS485 serial port protocol. X1.1 X2.1
Twisted pair
X1.2 X2.2
X1.3 X2.3
Twisted pair
X1.6 X2.6
B. Composition
X1.4 X2.4
One cable Twisted pair
X1.5 X2.5
X1.7 X2.7
Twisted pair
D. Technical Specifications X1.8 X2.8
Remarks:
EPU02D-02 and BBU monitor Cable Introduction (English) The EPU is an active device and reports alarms and status. The EPU must be
connected to the BBU.
The DCDU is a passive device and does not report alarms or status.
90%
E. Appearance
B. Composition C. Configuration Principle
One board main body TBD
UMPTe Introduction (English)
D. Technical Specifications
UMPTe1: Not includes satellite card. (In the initial phase of the NR, the TDD system is used, requiring
time synchronization. The main control board that does not contain the satellite card is not
UMPTe type recommended.)
UMPTe2: Delivered outside China (including the GPS satellite card).
UMPTe3: Delivered in China (including BeiDou/GPS dual-mode satellite card).
Transmission interfaces 2 x FE/GE (electrical interface, RJ45), 2 x FE/GE/10GE (optical interface, SFP)
Transmission bandwidth (DL+UL) 10 Gbps
RAT G/U/L/NB-IoT/NR
Three QSAs are inserted into three QSFP cages of the UBBPfw1 and UBBPfw2. Six SFP cages are displayed
on the board.
High-frequency Low-frequency
coverage, for example, coverage, for For details, please refer to
3.5 GHz frequency example, 1.8 GHz
band frequency band this technical document.
Cell radius
HEI interface
HEI interface
In co-subrack scenarios, the CPRI MUX connection mode is In inter-subrack scenarios, the CPRI MUX connection mode is preferred.
preferred. The CPRI MUX solution has one CPRI optical cable less than the dual-star solution.
The CPRI MUX solution has one CPRI optical cable less than Baseband processing board--LTE: UBBPd/UBBPe; NR: UBBPfw1
the dual-star solution.
Control Board--LTE: UMPT; NR: UMPTe (5G RAN2.0 supports L & NR in one UMPTe).
Application scenarios:
4G BBU + 5G BBU
(inter-connection between MPT) 1. The two subracks are separate-MPT: Implement NSA (optional).
2. The two subracks are co-MPT: CI interconnection is required for the two MPTs.
BBU39x0 BBU5900
Support LTE Support NR 3. The two LNR subracks implement uplink and downlink decoupling.
UMPTx(L) CI
UMPTe(N)
Add a group of optical modules and optical cables between the RRU and the BBU.
The types of optical modules and types of optical cables are the same as those of existing LTE.
UMPTx(L) CI
UMPTe(N) The following slide focus on the red interconnection solution.
E. Appearance
B. Composition
One QSFP port cable main body
C. Configuration Principles
Quantity: One cable is configured between two UBBPs.
(1) MPO connector
Length: 10 m, 30 m, or 100 m. For any other (2) Strap
(3) MPO connector
requirements, submit an RM workflow.
Note: The optical module interconnection of HEI port is different from that
of the CI port. Color rings need to be distinguished for CI, but not for HEI.
Electrical port backhaul solution: The Ethernet cable solution is used, supporting only GE.
Optical port backhaul solution: The optical module and optical cable solution (mainly introduced) are used, supporting 10GE.
C. Configuration Principles
Quantity: One for each UMPT
One user transmission backup feature can be configured.
C. Configuration Principles
Quantity:
(1) DLC connector
If one optical module is required in the transmission solution,
(2) Branch optical cable
configure one optical cable.
(3) Branch optical cable label
If two optical modules are required in the transmission
(4) FC connector
solution, configure two optical cables.
(5) LC connector
Length:
(6) SC connector
Determined based on the site survey. 10 m, 20 m, and 30 m
are provided.
Port type:
Determined based on the ODF. FC, LC, and SC are provided.
AAU5613
AAU5313
AAU5310
RRU5258
HAAU5213
• The AAU power cable is not included. Dimensions 585 mm x 300 mm x 152 mm (without the housing)
Weight 20 kg (without the housing)
• The AAU ground cable is not included.
Operating temperature -40 ºC to +50 ºC (without solar radiation)
C. Configuration Principle Wind resistance Front: 285 N (at 150 km/h)
Side: 110 N (at 150 km/h)
• One for one sector Back: 290 N (at 150 km/h)
*: To achieve the claimed effectiveness, the Relative humidity 5% RH to 100% RH
following four conditions should be met: 25°C,
Ingress protection rating IP65
50% load, 3:1 uplink/downlink configuration, and
batch 70% modules configured.
One group of optical modules + single optical cable Two groups of optical modules + two optical cables
SFP connector
SFP connector
SFP optical module (10
Gbit/s or 25 G bit/s)
SFP optical module (10
Gbit/s or 25 G bit/s) QSA adapter
UBBPfw1 UBBPfw1
A. Purpose
Connects the BBU baseband
D. Main Parameters E. Appearance
processing board and RRU/AAU.
Item Specifications
Type Single-mode Single-mode Multi-mode
Calculation. Suggestion: Single-mode dual-fiber bidirectional optical module is preferred in the DRAN scenario.
Note: The cost of a 10 G single-mode optical module is the same as that of a multi-mode optical module.
Calculation. Suggestions: Select only when the optical fibers are limited in the CRAN scenario.
Note: The single-fiber bidirectional optical module has LC interface, rather than DLC interface.
E. Appearance
C. Configuration Principles
Quantity:
If one AAU/RRU is configured with one pair of optical modules, configure one optical
cable.
If one AAU/RRU is configured with two optical modules, configure two optical cables. (1) Double LC connector
Length: (2) Branch optical cable
Determined based on the site survey. 10 types of cables ranging from 10 m to 100 m (3) Branch optical cable
are provided.
C. Configuration Principles
(1) DLC connector
Quantity: (2) Branch optical
If one AAU/RRU is configured with one pair of optical modules, configure cable
one optical cable. (3) Branch optical
If one AAU/RRU is configured with two optical modules, configure two cable label
Wavelength division multiplexing (WDM): Transmit multiple optical waves with different wavelengths synchronously in a single fiber.
It makes full use of the large bandwidth resources in the low loss area of the single-mode optical fiber. Using the multiplexer, it combines the optical waves of
different wavelengths at the transmit end, and then transmits the signals to the single-mode optical fiber. In the receiving part, the demultiplexer adopts the
multiplexing method of separating the optical waves of different wavelengths. Because the optical waves of different wavelengths are independent of each
other, the bidirectional transmission can be solved.
Different number of wavelengths can be multiplexed using different wavelength division multiplexers (demultiplexers or multiplexers).
According to the different channel spacing, WDM can be classified into Coarse Wavelength Division Multiplexing (CWDM) and Dense Wavelength Division
Multiplexing (DWDM).
Appendix: MO Introduction
Huawei Wireless Product Line released the DWDM passive WDM solution for wireless fronthaul from 19AC9x.
Three types are fixed at the BBU side (the frequency value ends with an even number).
The other three types are fixed at the RF module side (the frequency value ends with an odd number).
The optical modules on the BBU side can only send wavelengths according to 60# The optical modules on the RF module side can only receive wavelengths
196.0THz. according to 60# 196.0THz.
The optical modules on the BBU side can only receive wavelengths according to 59# The optical modules on the RF module side can only send wavelengths
195.9THz. according to 59# 195.9THz.
34061920 34061921
Optical modules must be used in pairs.
Note: Supports 14 optical fibers. Twelve optical fibers support twelve RRUs, one is a convergence optical fiber, and one is reserved.
Ultimate planning: Outdoor multiplexer and demultiplexer have six BOM numbers.
Support
Support
Two 24-wavelength boards + two 12-wavelength boards
Six 12-wavelength boards
One 48-wavelength board + two 12-wavelength boards
Core point:
E. Appearance
B. Composition
Up converter case (included)
Two up converters (included)
One management module (included)
One monitoring cable (included)
Input power cable of the up converter (configuration and site survey are required)
Ground cable of the up converter (configuration and site survey are required)
C. Configuration Principles
Each case supports two up converters and a maximum of four AAUs/RRUs.
Types of input power cables: Determined based on the region.
Length of the input power cable: The default value is 12 m, which can be manually changed. (1) EPU02D series subrack
Types of ground cables: Determined based on the region. (2) BDU65-03
(3) PMU 12A
Length of the ground cable: The default value is 2 m.
DCDU-12B BBU5900
RF module
DCDU input
BBU power cable
Customer DC RF module
power ground
distribution box cable
RF module power cable
RF module
Monitoring cable
COM_IN MON0
EPU02D-02 BBU5900
DCDU input
BBU power cable RRU5258
ground
cable
Customer DC
power
distribution box RRU power cable
DCDU-12B BBU5900
DCDU input
BBU power cable
RF
module
ground
cable
Customer DC
power
distribution box
RF module power cable
APU BBU5900
BBU power RF
DCDU input cable module
power cable ground
cable
Customer DC
power
distribution box
RF module
power cable
AAU5310 is mainly delivered to Korea, where the Centralize RAN scenario is used.
The power supply solution of the AAU5310 must be adopted in the outdoor. Blade power supplies and blade
batteries are recommended.
Blade power supply and blade battery in the wireless configurator are OPM30 VB and TBD.
Blade power supply and blade battery in the energy configurator are DPU40D and DBU40B.
In some scenarios, the AAU power supply distance is long. When the existing DCDU-12B, EPU02D-02, or APU
does not meet the requirements, AC power supply is recommended. The power supply and battery of the AC
blade are deployed under the tower.
48 V DC
220 V AC
PLC
DBU40B • PLC (Power Line Carrier Communication) is an approach to utilize the existing power
DPU40D
lines for the transmission of information.
• By source, the signal is modulated on carrier frequency and injected onto power line.
-48 V
• By sink, the signal is filtered out and demodulated.
AAU/RRU
Channel
Source modulate filter coupling
coding
Power
BBU line
PLC
eCPRI/CPRI Channel
Sink demodulate filter coupling
decoding
EMS
PLC communication block diagram
CPRI/eCPRI
Results:
1. The MEB alarm cable needs to be
added.
2. The MEB supports six dry contact
alarms. Dry contact
alarm cable
EMS
To third-party
power supply To MEB
83 Huawei Confidential
Specifications of MEB-06D
Item Specification
Dimensions (H x W x D) 240 mm x 86 mm x 60 mm
Weight 1.3 kg (2.87 lb)
Input power -48 V DC;
voltage range: -36 V DC to -57 V DC
Rated current 40 A
Power consumption 5W
Ambient temperature (long-term • With solar radiation of 1120 W/m ²: -40 ℃ to +50 ℃
operation) • Without solar radiation: -40 ℃ to +55 ℃
Relative humidity 5% RH to 95% RH
Ingress protection (IP) rating IP65
Neighboring eNB D D S U D D
Impacts and requirements of NR (TDD) base station clock source faults:
Interference
Downlink interferes uplink between base stations -> Inter-base station out-of-synchronization
Faulty eNB D D S U D D tolerance time
Downlink interferes uplink between UEs -> Inter-UE guard interval
The clock synchronization specifications of 5G NR (TDD) are basically the same as those of LTE
TDD: ±1.5us
GPS satellite/BeiDou satellite Solution introduction: Deploy the GPS at the site.
Solution features
Precision: The base station obtains the air clock source
directly, so the precision is high.
Reliability: There is no single point of failure, and the
impact scope is small.
Security: Only use the air clock source, which brings
security risks.
Deployment period: Deployed at the site, so the
deployment period is relatively short.
O&M: Easy to locate the fault.
Cost: GPS is required for each site, so the hardware
cost is high.
A. Purpose E. Appearance
D. Technical Specifications
Connects the RF output port of the The cables of 2 m, 3 m, 4 m, 6 m, and 10 m are 4.3-10 female
RRU and the antenna. available.