Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
- H/W -
March, 2014
This material is a property of Samsung Electronics Co., Ltd. Any unauthorized use of this material can be punished
under applicable International and/or domestic law.
- This document cannot be used without Samsungs Authorization -
Notice
All functionality, features, specifications and other product information provided in this
document including, but not limited to, the benefits, design, pricing, components,
performance, availability, and capabilities of the product are subject to change without
notice or obligation.
Samsung reserves the right to make changes to this document and the product described
herein, at anytime, without obligation on Samsung to provide notification of such change.
Contents
1.
2.
3.
Introduction
Specification
Fingerprint Sensor
Heart-Rate Sensor
Block Diagram
Component Layout
Troubleshooting
Troubleshooting
Boot Recovery
RF Calibration
Introduction
1. Specification
2. Fingerprint Sensor
3. Heart Rate Sensor
spec.
BODY
AP Chipset
Network
OS
Android OS V4.4.2(KitKat)
Memory
Display
Camera
Sensor
Connectivity
GPS
Battery
2,800mAh
Micro SD
SIM
Micro-SIM
- This document cannot be used without Samsungs Authorization -
Fingerprint Sensor
Primary Tx
(115)
Primary Rx
Secondary
Rx
Secondary Tx
(64)
- This document cannot be used without Samsungs Authorization -
Fingerprint Sensor
Tx Carrier Signal
No Finger
Ridge
Valley
Ridge
Rx AM Modulated Signal
- This document cannot be used without Samsungs Authorization -
Valley
Fingerprint Sensor
Sensor Test Mode (*#0*#)
Transmitting
Block
Receiving
Block
PPG(Photoplethysmogram) signal
1. Block Diagram
2. Component Layout
Component Layout
SUB ANT
(DRX B7 + GPS)
FLASH LED +
HRM SENSOR
SUB ANT
(DRX B1/2/3/5/8/20 +
BT/WIFI)
16M CAM
SIM + microSD
SOCKET
BATTERY
(2,800mAh)
ACCESSARY
CONTACT PINS
SPEAKER
MAIN ANT
Component Layout
2ND MIC HOLE
ANT CONTACT
ANT CONTACT
POWER KEY
VOLUME KEY
EAR-JACK
RECEIVER
IR LED
WINDOW
GRAPHITE
SHEET
SPEAKER
ANT CONTACT
Component Layout
FRONT CAM
MOTOR
16M CAM
VOLUME
KEY FPCB
MAIN PBA
OCTA
BRACKET
COAXIABLE
CABLE1,2
Fingerprint
HOME KEY
FPCB
SUB PBA
Component Layout
Component Layout
RGB / PROXIMITY /
GESTURE SENSOR
NFC
HRM
CAMERA
BT / WIFI
SENSOR
HUB
MHL
AUDIO
AP POWER
BLOCK
CHARGING /
SUB PMIC /
DISPLAY POWER
AP / MEMORY
RF BLOCK
Component Layout
ANT400
Ant. Contact (for GPS)
MIC801
SUB MIC
ANT815/816
RCV Contact
ANT1101/1102
Ant. Contact (for Sub Ant.1)
U407
Magnetic Sensor
ANT401/402
Ant. Contact (for BT/WIFI)
U410
NFC
F1107
CRX MLB LNA
(BAND1/2/3/5/8/20)
ANT1100/1103
Ant. Contact (for Sub Ant.2)
ANT401/402
Ant. Contact (for BT/WIFI)
U804
Audio Codec
SIM600
SIM/SD CARD SOCKET
ANT806/807
Power key Contact
U400
HRM SENSOR
U7002
GPIO Expander
U406
6 Axis Sensor (GYRO,ACCEL)
U403
SENSOR Hub
U1001
MHL 2.0
LED7000
Flash LED
ANT403/404/7000/7001/7005
COVER Contact
U7003
PMIC
U302
Transceiver
U7004
FPGA
ANT808/811/812/813/814
Earjack Contact
BTC7000
Battery Connector
U105
SUB MLB SW
(BAND1/2/3/5/8/20)
F102
BAND1 PRX
U803
2-MIC CHIP
F101
MAIN FEMID
(BAND1TX/2/3/5/8/20)
U103
MAIN SWITCH
(BAND7/38/40/B1 PRX)
HDC400
BTP IF Conn
U901
OVP IC
Component Layout
LED1000
SVC LED
U1000
Gesture Sensor
IRDA1000
IRDA
U404
Barometer Sensor
U1104
RF Switch (BAND1/2/3)
HDC900
VT Camera Connector
U1109
RF Switch (BAND5/8/20)
HDC901
16M Camera Connector
ANT803/804/805
Volume key Contact
U903
DC/DC DDI_Core 1.5V
U405
BT/WIFI
HDC902
OCTA Connector
ANT800/801
Vibration Motor Contact
U900
OCTA DC-DC
U904
Companion IC
UCP500(upper part)
POP MEMORY
U7005
Ext.Buck for 16M Camera
UCP500(lower part)
Application
& Communication
Proccesor
U7000
IF PMIC
UME6000
eMMC MEMORY
U7006
SUB PMIC
PA201
BAND7 PAD (PA+DPX)
PA200
BAND1/2/3/5/8/20, GSM
QUAD MMMB PA
U907
Load Switch
U805
MAIN MIC Bias LDO
HDC903
SUB FPCB IF Connector
Troubleshooting
Troubleshooting
Boot Recovery
RF Calibration
Check point
Result value
Defect point
Solved
Battery
Not solved
Circuit short
C7030 = 3.8V
(same as power supply voltage)
IF PMIC (U7000)
C7023 = 1.8V
19.2MHz
X-TAL (OSC7000)
Step5
Step5
U7000
U7003
C7030
C7023
OSC7000
Step6
Step6
UCP500
Check point
Result value
Defect point
Abnormal
Settings
Normal
Coaxial cable
Main ant, diversity ant
Normal
Abnormal status
(compared with a good PBA)
RF components.
U302 Transceiver
F101 Main FEMID
PA200 PAM(Power Amplitude Module)
F1107 Sub FEM
U301 PA DCDC
Normal status
(compared with a good PBA)
CP(Call Processor)
(UCP500)
CP PMIC(U7003)
Troubleshooting - RF (GSM,WCDMA,LTE)
Step2
Step2
Step3
Step3
Coaxial cable
(connect Main Ant.
with PBA)
CHECK SETTINGS
DEBUG SCREEN
STATUS
Same value compared
with normal device.
Main
ANTENNA contact
Step5
Step5
U301 PA DCDC
Step3
Step3
U302 Transceiver
Diversity
ANTENNA contact
Troubleshooting - BT/WIFI
Step
Check point
Result value
Defect point
Turned on
Turned off
Turn on
Normal
C427 = ~1.8V
PMIC (U7003)
C428 = ~1.5V
BT/WIFI IC (U405)
L410
or BT/WIFI IC (U405)
Troubleshooting - BT/WIFI
Step1
Step1
Step2
Step2
ANT402
Step4
Step4 &
& 55
BT/ WIFI IC
L410
C427
C428
U7003 (PMIC)
ANT401
Troubleshooting - NFC
Step
Check point
Result value
Defect point
Turned on
Ir al siguiente paso
Turned off
Turn on
BATTERY
Normal
R419=1.8V
Si no es el valor correcto
PMIC (U7003)
PRINCIPAL
CHIP(UCP500) o
Chip(U410) de NFC
Si no es el valor correcto
PMIC (U7003)
or OSC7000
Troubleshooting - NFC
Step1,2
Step1,2
CHECK SETTING
Step
Step 4,5
4,5
R419
U401
R7004
UCP500
Troubleshooting - GPS/GLONASS
Step
1
Check point
Confirm the defect symptom
(Check the turned on GPS function)
Check the status ANT400, GPS ANT & Contact
Power on with a power supply
(power supply voltage : 3.8V)
Check the voltage of C406
Result value
Defect point
Turned on
Turned off
Turn on
ANT400
GPS ant
Normal
C406 = 2.8V
PMIC(U7003)
C405= 1.8V
Main Chip(UCP500)
C308 = 19.2Mhz
(Same signal compared with
a good PBA)
GPS IC(U302)
GPS LNA(U402)
PMIC (U7003)
or OSC7000
Step2
Step2
ANT400
GPS ANTENNA
(LDS Type)
GPS ANTENNA
Contact
Step4,5,6
Step4,5,6
UCP500
U402
C406
C308
C405
Check point
Confirm the defect symptom
Check the Main Camera connector (HDC901)
Result value
Defect point
Normal
Solved
Main Camera
Not solved
PMIC(U7003)
SUB PMIC(U7006)
U7005 or L7015
C902 = 0.875~1.0V
R916 = 24MHz
MAIN CHIP
Step2
Step2
C907 C908
Step8
Step8
Step6,
Step6, 77
C950
C902
R916
C917
Check point
Confirm the defect symptom
Check the AMOLED connector (HDC902)
Result value
Defect point
AMOLED connector
(HDC902)
Normal
Solved
AMOLED
Not solved
PMIC(U7003)
C906=3.0V
U903
C921=1.5V
U900
C903 = 7.0V
C919 = -1.4 ~ -4.4V
C920 = 4.6V
MAIN CHIP
Step2
Step2
LCD CONNECTOR
HDC902
C906
U900
C921
Step7
Step7
C903
C919
C920
Check point
Confirm the defect symptom
Check the AMOLED connector (HDC902)
Result value
Defect point
AMOLED connector
(HDC902)
Normal
Solved
TSP
Not solved
PMIC(U7003)
C911 = 1.8V
C922 = 3.3V
R506,R508
C911
C922
U7003
R508
R506
Check point
Result value
Defect point
Solved
Setting error
Not solved
Solved
speaker
Not solved
Go to step 7
No signal
Go to step 8
Solved
Assembly error
Not solved
Go to step 3
Solved
SUB PBA
Not solved
Step6
Step6
Assy SUB PBA
(GH96-07020A)
Assy case-rear
(GH98-32015A)
Speaker contacts
Speaker (3001-002733)
Step8
Step8
Reverse
HDC903
Connector
U804
Audio Codec
Check point
Result value
Defect point
Solved
Setting error
Not solved
connector
Normal
Solved
Receiver
Not solved
No signal
Audio codec
(U804)
Okay
Not okay
Modem (UCP500)
Step3
Step3
Receiver
Assy case-rear
(GH98-32015A)
Receiver connector
(ANT815, ANT 816)
Step7,
Step7, Step8
Step8
U803
2-MIC Chip
U804
Audio Codec
Check point
Result value
Defect point
Dust
Normal
Wrong insert
Re-insert
Normal
1.8V
- Main MIC :
MIC LDO(U805)
- SUB MIC :
Audio codec(U804)
No CLK Signal
Audio codec(U804)
MIC
Microphone
Microphone
Rubber Holder
Step5,
Step5, 66
U805
MIC LDO
C952 / MIC DATA
C825 / MIC BIAS
Check point
Result value
Defect point
Solved
Oscillator(OSC400)
Not solved
Solved
Sensor Hub(U403)
Not solved
Sensor
Caution: Temperature/Humidity sensor should not be directly exposed to the heat-gun when you replace
USB connector, because excessive heat can cause abnormal operation of the sensor. The temperature
that Temperature/Humidity sensor sees should not exceed 260C. Use proper heat-shielding material to
protect Temperature/Humidity sensor
Step2,3
Step2,3
I2C Pull up
Resistor
I2C Pull up
Resistor
*#0*#
Sensor
Sensor hub
Oscillator
Sensors
Sensors
Accelerometer & Gyro
Magnetic
Barometer
HRM
Boot Recovery
- Brief Process of Boot Recovery
1) Make T-Flash card for boot recovery.
2) Turn on the defective phone with T-Flash card inserted.
3) Download full S/W when the defective phone enters download mode automatically.
- Preparations
1) One normal SM-G900F phone
2) One micro-SD CARD (4GB)
3) Odin3 v3.09.exe
4) MSM8974PRO_boot_recovery.pit
5) Bootloader.tar.md5
Boot Recovery
Download bootloader file into T-Flash card using normal phone.
Boot Recovery
Screen of downloading with T-Flash card
Boot Recovery
Turn on the defective device with the T-Flash Card inserted.
It will automatically make the device go into the download mode.
Boot Recovery
Download full S/W.
RF Calibration
Power Divider
50ohm Termination
RF CABLE
(1 for PRX, 1 for DRX)
RF calibration
1. Download Factory Binary for calibration
Filename
DASEUL_Launcher_v3.0.22.exe
Remark
RF calibration
1) Run Daseul Launcher Program
RF calibration
2) Select Sequence Files and click Start.
3) Check Calibration
RF calibration
4) Click Hardware Config option and Select Port number like capture.
5) Click Save and OK to enter Calibration program.
RF calibration
6) Click START button and check if Running message appears.
Q&A
Question