Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Commissioning
www.huawei.com
Foreword
Page2
References
Page3
Objectives
Page4
Contents
1. Preparation and Data Configuration
2. Local Office Commissioning
3. Interconnection Commissioning
4. Signaling Transfer Commissioning
5. Service Commissioning
Page5
Steps of Commissioning
Preparation
Page6
CHK VERSION
DSP PATCH
Page7
Notes:
Page8
Method 1:
Method 2:
Method 3:
Page9
Contents
1. Preparation and Data Configuration
2. Local Office Commissioning
3. Interconnection Commissioning
4. Signaling Transfer Commissioning
5. Service Commissioning
Page10
Contents
2.Local Office
Commissioning
2.1 Boards
Commissioning
2.2 Clock Commissioning
2.3 Cascading
Commissioning
Page11
Boards Commissioning
On the LMT, click the Device Panel tab and click Device
Management.
Page12
Contents
2. Local Office
Commissioning
2.1 Boards Commissioning
2.2 Clock Commissioning
2.3 Cascading Commissioning
Page13
Remarks
Free
running
Fast
tracking
Indicates the CLK board is quick locking the reference source clock.
Usually, it occurs in the moment when the system is accessing the
reference source.
Locked
Indicates the CLK board has locked the reference source and
outputs the clock corrected by the reference source.
Holdover
Indicates the CLK board lost the reference source traced and outputs
clock based on phase-lock parameter saved during tracing.
Page14
Only be used when the UMG8900 locks the peer E1 line clock.
Check the status of the E1 port that extracts line clock.
Only be used when the UMG8900 locks the peer E1 line clock.
Check the slip statistics of the E1 port that extracts line clock. It
can make slip statistics for the latest 15 minutes or 24 hours.
Page15
Page16
Contents
2. Local Office
Commissioning
2.1 Boards Commissioning
2.2 Clock Commissioning
2.3 Cascading
Commissioning
Page17
Cascading Commissioning
Page18
Contents
1. Preparation and Data Configuration
2. Local Office Commissioning
3. Interconnection Commissioning
4. Signaling Transfer Commissioning
5. Service Commissioning
Page19
Contents
3. Interconnection Commissioning
3.1 Connecting with MGC
3.2 Connecting with BSC, MSC, PSTN
3.3 Connecting with MGW
Page20
Remark
The PPU
interface
The OMU
interface
The MPU
interface
Note: Use the PING command to check the H.248 interface address!
Page21
H.248 Interface
Commissioning
Step1: Check the LINK indicator of the H.248 interface.
Page22
Gateway Registration
Commissioning
Remark
DSP H248LNK Checking the status of H.248 signaling links. The link
status should be UP if the transport layer is SCTP and
TCP.
LST H248LNK
LST SCTPINIT
LST
H248PARA
LST VMGW
Page23
Contents
3. Interconnection Commissioning
3.1 Connecting with MGC
3.2 Connecting with BSC, MSC,
PSTN
3.3 Connecting with MGW
Page24
E1 Interfaces Commissioning
Ste
p
Remark
Take out all E1 connectors of an E32/T32 from the DDF. Make selfloop on the E1 interface.
Page25
E1 Interfaces Commissioning
Step
Remark
LOP E1: the loopback mode is set to OUTLOP (Remote). Ask the peer side
to check status of the peer E1 interface. The peer E1 interface should be in
the OK state.
If the links are normal, go to step 3; if abnormal, continue with step 2.
Make loopback tests section by section to determine the very section with
transport problems.
The loopback tests prove interfaces are OK, but they become FAULT again
after loopbacks. In this case, run DSP E1PORT to check if the frame
structure and line coding scheme of the UMG8900 match those of the peer
device.
Page26
E1 Interfaces Commissioning
Step
4
Page27
E1 Interfaces Commissioning
Local exchange
Receive
Send
Send
Receive
Send
Receive
Receive
Send
E1 A
E1 B
E1 A
E1 B
Note:
Set the peer device in remote loopback mode and the UMG8900 with no
loopback before running this command !
Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved.
Page28
Step2: To conduct loopback test with a flange at the ODF for both sides,
and check the SDH interface indicators of both sides.
Step3: If the LINK indicator is on during loopback test but off after the
test, check if the receive and send cables are inserted to interfaces
reversely.
Page29
Contents
3. Interconnection Commissioning
3.1 Connecting with MGC
3.2 Connecting with BSC, MSC, PSTN
3.3 Connecting with MGW
Page30
IP Bearer Commissioning
Item
Remark
LST IPIF
DSP GWADDR
PING
Page31
Contents
1. Preparation and Data Configuration
2. Local Office Commissioning
3. Interconnection Commissioning
4. Signaling Transfer Commissioning
5. Service Commissioning
Page32
Contents
4. Signaling Transfer Commissioning
4.1 MTP2-M2UA Signaling Links
Commissioning
4.2 MTP3-M3UA Signaling Links Commissioning
Page33
SEP
SS7
IP
UMG8900
S7UP
S7UP
MTP3
MTP3
M2UA-NIF
MTP2
MTP2
MTP1
MGC
TDM
M2UA
M2UA
SCTP
SCTP
IP
MTP1
MAC
IP
Page34
IP
MAC
MTP2-M2UA Commissioning
Steps
Step 1: Checking Status of M2UA Links
Page35
Contents
4. Signaling Transfer Commissioning
4.1 MTP2-M2UA Signaling Links Commissioning
4.2 MTP3-M3UA Signaling Links
Commissioning
Page36
SEP
SS7
IP
UMG8900
MGC
S7UP
S7UP
MTP3
MTP3
MTP2
MTP2
MTP1
M3UA
M3UA-NIF
TDM
SCTP
IP
MTP1
SCTP
M3UA
MAC
IP
IP
MAC
Page37
MTP3-M3UA Commissioning
Steps
Step 1: Checking Status of MTP3 Links
Note:
1. SLS is NULL indicates that MTP3 link setup fails !
2. DSP SPFSUBRD to check the subboard handling the MTP2 links for any fault !
Page38
MTP3-M3UA Commissioning
Steps
Step 3: Checking Status of M3UA Links
Note: To make changed SCTP parameters valid, you have to restart the SPF
first !!
Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved.
Page39
Contents
1. Preparation and Data Configuration
2. Local Office Commissioning
3. Interconnection Commissioning
4. Signaling Transfer Commissioning
5. Service Commissioning
Page40
Service Commissioning
The most direct and efficient way for service commissioning is to make
test calls. In different networking applications, the steps for service
debugging are different. The following steps are just for reference.
Voice
service
Requirement
Page41
Service Commissioning
Page42
Service Commissioning
CW
Use MS A to call MS B.
CH
Use MS A to call MS B.
Page43
Service Commissioning
Requirement
MPTY
service
Requirement
Data
service
Conversation is clear,
image is uninterrupted.
Page44
Summary
Page45
Thank you
www.huawei.com