Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
82-2
Objectives
Set up various workpieces for grinding
Observe the safety rules to operate the grinder Grind flat, vertical, and angular surfaces
82-3
Surface Grinding
Primarily for grinding flat surfaces on hardened or unhardened workpiece Perform operations such as form, angular, and vertical grinding Good results depend on several factors:
Proper mounting Proper wheel selection for job
82-4
82-5
Thin Workpieces
Tend to warp because of heat created during grinding
Minimize by mounting workpiece at angle of 15 to 30 from side of chuck
Reduces length of time wheel in contact with work
82-6
Short Workpieces
Work that does not straddle three magnetic poles generally not held firmly enough for grinding Advisable to straddle as many poles as possible
Set parallels or steel pieces around work to prevent it from moving
Parallels should be slightly thinner than workpiece
82-7
Grinder Safety
1. Before mounting a grinding wheel, ring test wheel to check for defects 2. Be sure grinding wheel properly mounted on spindle 3. See wheel guard covers at least one-half wheel 4. Make sure magnetic chuck has been turned on by trying to remove work
82-8
5. See that grinding wheel clears work before starting grinder 6. Be sure grinder operating at correct speed for wheel being used 7. When starting grinder, always stand to one side of wheel 8. Never attempt to clean magnetic chuck or mount and remove work until wheel has stopped completely 9. Always wear safety glasses when grinding
82-9
82-10
5. Set crossfeed for type of grinding operation roughing cuts, .030 to .050 in.; finishing cuts, .005 to .020 in. 6. Bring work under grinding wheel by hand, having about 18 in. of wheel edge over work 7. Start grinder and lower wheelhead until wheel just sparks work 8. Wheel may have been set on low spot of work.
82-11
Cutting fluid should be used whenever possible to aid grinding action keep cool 9. Start table traveling automatically and feed entire width of work under wheel to check for high spots 10. Lower wheel for every cut until surface is completed roughing cuts, .001 to .003 in.; finishing cuts, .0005 to .001 in. 11. Release magnet and remove workpiece by raising one edge to break attraction
82-12
Cause
Possible Reme
Burning or Wheel is too hard. Use a softer, free-cutting whee discoloration Decrease wheel speed. Increase work speed. Coarse-dress the wheel. Portion of table Take lighter cuts and dress the wheel frequently. taken from text Use coolant directed point of contact between wheel, work Burnished Wheel is glazed. work surface
82-13
82-14
82-15
5. Hold work firmly against angle plate and turn on magnetic chuck 6. Clamp work to angle plate and set clamps so they will not interfere with grinding operation 7. Turn off magnetic chuck and carefully place base of angle plate on magnetic chuck 8. Carefully fasten two more clamps on end of workpiece to hold work securely
82-16
82-17
4. Start grinding wheel and lower wheelhead until wheel just sparks work 5. Move work clear of wheel with crossfeed handle 6. Raise wheel about .005 to .010 in. in case wheel has been set to low spot on work 7. Check for high spots by feeding table by hand so entire length and width of work passes under wheel
82-18
8. Engage table reverse lever and grind surface until all marks removed
9. Stop machine and remove clamps from right-hand end of work 10. Turn off magnetic chuck and remove angle plate and workpiece as one unit 11. Clean chuck and angle plate
82-19
12. Place angle plate (with attached workpiece) on end, with surface to be ground at top 13. Fasten two clamps to right-hand side of workpiece and angle plate 14. Remove original clamps from top of setup 15. Repeat steps 1 to 8 and grind second edge 16. Remove assembly from chuck and remove workpiece from angle plate
82-20
82-21
4. Grind third edge to required size 5. Repeat operations 1 to 3 and grind 4th edge
82-22
82-23
Dressing
Operation of removing some of bond material from surface of trued wheel to expose abrasive crystals and allow wheel to cut
82-24
82-25
82-26
3. Clean magnetic chuck and place diamond holder on left-hand side of chuck
Cover as many magnetic inserts as possible Energize chuck
4. Adjust grinder table to locate diamond nib about 12 in. to left of wheel centerline
Lock table in position
5. Lower wheelhead by hand until just touches piece of paper held between wheel and diamond
82-27
6. Turn grinder crossfeed handle so diamond clears edge of wheel 7. Lightly coat wheel surface to be trued with wax marking crayon 8. Start grinder spindle and feed wheelhead down in .0004 in. increments until contact made with diamond 9. Direct coolant to wheel-diamond interface 10. Feed diamond across wheel face at 3 to 12 in./min 11. Continue truing until crayon removed
82-28
82-29
82-30
5. Use crossfeed handle to bring edge of dressing stick even with edge of wheel
8. Using slow but steady feedrate ( 5 to 10 ft./min) take one pass lengthwise along dressing stick
82-31
9. At end of pass, index table slightly less than width of grinding wheel 10. Repeat procedure until width of dressing stick ground 11. Downfeed wheel after full surface of dressing stick has been ground 12. When grinding wheel appears to be cutting dressing stick freely, stop and inspect wheel face
Surface feels rough dressing complete
82-32
82-33
Mounting the Workpiece 4. Remove burrs from magnetic chuck and workpiece and thoroughly clean chuck 5. Place piece of smooth paper between work and magnetic chuck; energize chuck Setting Speeds and Feeds 6. Adjust table reverse dogs so center of grinding wheel clears each end of work to be ground by 1 in.
82-34
8. Set table speed rate from 50 to 100 ft/min 9. Set spindle speed for size and type of CBN wheel used Setting wheel to work surface 10. Set wheel to top of work surface 11. Traverse workpiece under revolving wheel to locate high spot of work surface
82-35
12. Move table so wheel clears edge of work surface to be ground Coolant 13. Use proper grinding fluids to suit wheel and workpiece 14. Stop grinder spindle and adjust coolant nozzle so it is about in. above work surface and as close to wheel face as possible
82-36
15. Place dummy block, slightly lower than work surface, at right-hand end so entire surface receives coolant at all times
Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
82-37
Grinding the Surface 16. Start grinder spindle and lower wheelhead .001 in. for first cut 17. Start coolant flow 18. Start table reciprocating and engage crossfeed to take roughing pass 19. Be sure edge of grinding wheel clears side of work after each pass 20. Take as many passes (.001 in.) as needed 21. Set wheelhead for .0005 in. depth for final pass to improve surface finish
82-38
82-39
5. Turn on magnetic chuck and test to see if work held securely 6. Set reversing dogs 7. Bring side of wheel close to vertical surface to be ground 8. Lower wheel to within .002 to .005 in. of flat or horizontal surface finish ground 9. Start table slowly and feed wheel across until just sparks vertical surface
82-40
10. Rough-grind vertical surface to within .002 in. of size by feeding table in .001 in. maximum per pass 11. Redress side of wheel if necessary 12. Finish-grind vertical surface by feeding table approximately .0005 in. maximum per pass
82-41
Hold work flat and dress grinding wheel to required angle with sine dresser
Sine dresser not available, parallel set to desired angle by means of sine bar may be clamped to angle plate setup placed on magnetic chuck
82-42
Form Grinding
Production of curved and angular surfaces produced by means of specially dressed wheel Reverse form or contour required on workpiece is dressed on grinding wheel Contours and radii may be produced by means of radius wheel dresser
Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
82-43
82-44
4. Place gage block buildup using wear blocks on each side, equal to radius required on grinding wheel
Between height-setting bar and diamond point
5. Raise diamond until just touches gage blocks then lock in position 6. Move table longitudinally until diamond is under center of grinding wheel 7. Lock table to prevent longitudinal movement
82-45
8. Rotate arm of radius dresser of turn so diamond is in horizontal position 9. Start machine spindle and bring diamond in until just touches side of grinding wheel
Using crossfeed handle
10. Lock table cross-slide in position 11. Stop grinder and raise wheel until clears diamond
82-46
12. Start grinder and lower wheel until it just touches diamond
Slowly rotate diamond back and forth through 90 arc
13. Feed wheel down approximately .002 to .003 in. for every rotation of dresser 14. Continue to dress radius until periphery of wheel just touches diamond when it is in vertical position 15. Stop grinder, raise wheel, remove dresser
82-47
Crush-Formed Wheels
Tool-steel or carbide Grinding roll wheel having Wheel assumes desired then form reverse used or to form grind contour of finished of crushing workpiece roll form or contour on workpiece
Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
82-48
82-49
Cutting-Off Operations
Using thin cutoff wheels to cut off hardened materials using the surface grinder Work clamped in fixture or vise and positioned below wheel Thin, short pieces, wheelhead fed straight down; longer pieces, work mounted and table is reciprocated while wheel fed down Diamond wheels used on carbide