Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Repeaters Mobile Infrastructure LTE / WCDMA / CDMA / EDGE General Purpose Wireless
SOT-89 Package
Product Features
100-4000 MHz 13 dB Gain @ 1.9 GHz 1.3 dB Noise Figure @ 1.9 GHz +41 dBm Output IP3 +23.6 dBm P1dB 50 Ohm Cascadable Gain Block Unconditionally Stable High Input Power Capability +5V Single Supply, 125 mA Current SOT-89 Package
1 RF IN
2 GND
3 RF OUT
General Description
The TQP3M9007 is a high linearity low noise gain block amplifier in a low-cost surface-mount package. At 1.9 GHz, the amplifier typically provides 13 dB gain, +41 dBm OIP3, and 1.3 dB Noise Figure while drawing 125 mA current. The device is housed in a leadfree/green/RoHS-compliant industry-standard SOT89 package. The TQP3M9007 has the benefit of having high linearity while also providing very low noise across a broad range of frequencies. This allows the device to be used in both receive and transmit chains for high performance systems. The amplifier is internally matched using a high performance E-pHEMT process and only requires an external RF choke and blocking/bypass capacitors for operation from a single +5V supply. The internal active bias circuit also enables stable operation over bias and temperature variations. The TQP3M9007 covers the 0.1 - 4 GHz frequency band and is targeted for wireless infrastructure or other applications requiring high linearity and/or low noise figure.
Pin Configuration
Pin #
1 3 2, 4
Symbol
RF IN RF OUT GND
Ordering Information
Part No.
TQP3M9007 TQP3M9007-PCB
Description
High Linearity LNA Gain Block 0.5-4 GHz Evaluation Board
Standard T/R size =1000 pieces on a 7 reel. Data Sheet: Rev D 12/27/11 2011 TriQuint Semiconductor, Inc. - 1 of 9 Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network
TQP3M9007
W High Linearity LNA Gain Block Specifications Absolute Maximum Ratings
Parameter
Storage Temperature RF Input Power,CW,50 ,T=25C Device Voltage,Vdd
Rating
-55 to 150 oC +20 dBm +7 V
Min
3 -40
Typ
5
Max Units
5.25 +85 190 V o C o C
Operation of this device outside the parameter ranges given above may cause permanent damage.
Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions.
Electrical Specifications
Test conditions unless otherwise noted: +25C, +5V supply, 50 system.
Parameter
Operational Frequency Range Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 Noise Figure Supply Voltage, Vdd Current, Idd Thermal Resistance (jnc to case) jc
Conditions
Min
100
Typical
1900
Max
4000
Units
MHz MHz dB dB dB dBm dBm dB V
11.5
13 18 13 +23.6
14.5
See Note 1.
+37
mA
o
C/W
Notes: 1. OIP3 is measured with two tones at an output power of 4 dBm / tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the OIP3 using 2:1 rule. 2:1 rule gives relative value with respect to fundamental tone.
- 2 of 9 -
Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network
TQP3M9007
W High Linearity LNA Gain Block Device Characterization Data
S11
6 0.
S22
Swp Max 6GHz
6 0.
1.0
0.8
30 25
3.
10.0
10.0
Gain (dB)
20 15
10.0
0.2
0.4
0.6
0.8
1.0
2.0
3.0
4.0
5.0
0.2
0.4
0.6
0.8
1.0
2.0
3.0
4.0
5.0
10 5 0.0
-0
.4
.4 -0
.0
-2
-0 .6
-0.8
-1.0
-0.8
Frequency (GHz)
S-Parameter Data
Vdd = +5 V, Icq = 125 mA, T = +25C, unmatched 50 ohm system, calibrated to device leads
Freq (MHz) 50 100 200 400 800 1000 1200 1500 1900 2000 2200 2500 2600 3000 3500 4000
S11 (dB) -9.21 -9.18 -9.58 -11.09 -13.55 -14.69 -15.31 -16.32 -16.36 -16.44 -16.55 -16.78 -16.83 -17.62 -18.79 -20.11
S11 (ang) -171.69 178.66 168.58 155.91 148.37 147.37 148.14 152.38 155.45 154.43 154.33 153.75 154.69 157.51 154.34 176.37
S21 (dB) 21.92 21.72 21.39 20.71 18.58 17.47 16.33 14.85 13.11 12.73 11.98 10.97 10.59 9.53 8.24 7.01
S21 (ang) 165.87 164.31 154.89 134.86 99.19 84.06 70.48 52.18 30.26 25.52 15.20 0.51 -4.70 -24.26 -48.07 -72.56
S12 (dB) -28.66 -28.54 -28.25 -27.05 -24.58 -23.58 -22.59 -21.45 -19.96 -19.77 -19.13 -18.24 -18.14 -17.17 -16.19 -15.53
S12 (ang) 7.52 8.08 11.48 16.59 17.74 14.87 12.31 6.08 -2.85 -5.72 -12.30 -20.16 -23.60 -36.43 -53.90 -72.99
S22 (dB) -10.26 -10.62 -10.93 -11.61 -12.39 -13.43 -13.72 -14.84 -15.21 -15.43 -16.18 -16.76 -16.24 -16.21 -14.74 -11.54
-1.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
-0 .6
-2
.0
S22 (ang) -177.68 166.81 145.14 112.74 63.78 40.99 23.70 -3.77 -32.08 -42.20 -54.41 -84.02 -91.43 -128.42 -165.72 154.74
- 3 of 9 -
Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network
-3 .0
-3
.0
Gain (dB)
-4 .0 -5. 0
-4 .0 -5. 0
2 -0.
2 -0.
-10.0
0.2
-10.0
0.2
0 4.
5.0
0. 4
0. 4
2.
0.8
1.0
3.
0 4.
5.0
10.0
TQP3M9007
W High Linearity LNA Gain Block Application Circuit Configuration
GND J3
C3
C1
Q1
C2 C6
Notes: 1. See PC Board Layout, under Application Information section, for more information. 2. Components shown on the silkscreen but not on the schematic are not used. 3. B1 (0 jumper) may be replaced with copper trace in the target application layout. 4. All components are of 0603 size unless stated on the schematic. 5. C6 and L2 value are critical for linearity performance.
Value
Description
High Linearity LNA Gain Block Cap, Chip, 0603, 50V, NPO, 5% Cap, Chip, 0603, 50V, NPO, 5% Cap, Chip, 0603, 16V, X7R, 10% Ind, Chip, 0603, 5% Res, Chip, 0603, 1/16W, 5%
Manufacturer
TriQuint various various various various various various
Part Number
TQP3M9007
- 4 of 9 -
Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network
TQP3M9007
W High Linearity LNA Gain Block Typical Performance TQP3M9007-PCB
Test conditions unless otherwise noted: +25C, +5V, 125 mA, 50 system. The data shown below is measured on TQP3M9007-PCB
Frequency
Gain Input Return Loss Output Return Loss Output P1dB OIP3 [1] Noise Figure [2]
MHz
dB dB dB dBm dBm dB
500
20 11.5 10.5 +22.9 +39.3 1.4
900
18 14 13 +23.3 +40.2 1.2
1900
13 18 13 +23.5 +41.1 1.3
2100
12 17.5 12 +23.8 +42.2 1.4
2600
10 15.5 10.5 +24.0 +42.2 1.8
Notes: 1. OIP3 measured with two tones at an output power of +4 dBm / tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the OIP3 using 2:1 rule. 2. Noise figure data shown in the table above is measured on evaluation board and corrected for the board loss of about 0.13 dB @ 1.9 GHz.
Performance Plots
Performance plots data is measured using TQP3M9007-PCB. Noise figure plot has been corrected for evaluation board loss of 0.13 dB @ 1.9 GHz.
24 22 20 18
Gain (dB)
3.0
3.5
4.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Frequency (GHz)
4.0 3.5 3.0
NF (dB)
Vcc = 5 V
Frequency (GHz)
50
Frequency (GHz)
50 +85C +25C 30 C 40C
OIP3 (dBm)
40
OIP3 (dBm)
2.5
45
45
40
35
35
30 0 2 4 6 8 10 12
Frequency (GHz)
- 5 of 9 -
Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network
TQP3M9007
W High Linearity LNA Gain Block
50
25
-30 -35
ACLR1 (dBc)
45
OIP3 (dBm) P1dB (dBm)
24
40
23
35
22 -40 -20 0 20 40 60 80
-60
Frequency (GHz)
30 25
Output Power (dBm)
OIP3 (dBm)
Temperature (C)
45 1900MHz 900MHz 40
P1dB (dBm)
25
35
20
30
15
25 3 4 5 6 7
10 3 4 5 6 7
Vdd (Volts)
Vdd (Volts)
Idd vs Vdd
Vdd (Volts)
- 6 of 9 -
Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network
TQP3M9007
W High Linearity LNA Gain Block Pin Description
GND 4
1 RF IN
2 GND
3 RF OUT
Pin
1 3 2, 4
Symbol
RF Input Vdd / RFout GND Paddle
Description
Input, matched to 50 ohms. External DC Block is required. Output, matched to 50 ohms, External DC Block is required and supply voltage. Backside Paddle. Multiple vias should be employed to minimize inductance and thermal resistance; see page 7 for mounting configuration.
- 7 of 9 -
Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network
TQP3M9007
W High Linearity LNA Gain Block Mechanical Information Package Information and Dimensions
Markings: Part number: 3M9007 Assembly code: Y is last digit of part manufacture year. XXX is lot code. 3M9007 YXXX
Notes: 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135) diameter drill and have a final plated thru diameter of .25 mm (.010). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. RF trace width depends upon the PC board material and construction. 4. Use 1 oz. Copper minimum.
- 8 of 9 -
Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network
TQP3M9007
W High Linearity LNA Gain Block Product Compliance Information ESD Information Solderability
Compatible with both lead-free (maximum 260C reflow temperature) and lead (maximum 245C reflow temperature) soldering processes. ESD Rating: Value: Test: Standard: ESD Rating: Value: Test: Standard: Class 1A Passes 250 V to < 500 V Human Body Model (HBM) JEDEC Standard JESD22-A114 Class IV Passes 1000 V Charged Device Model (CDM) JEDEC Standard JESD22-C101 This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). This product also has the following attributes: Lead Free Halogen Free (Chlorine, Bromine) Antimony Free TBBP-A (C15H12Br402) Free PFOS Free SVHC Free
MSL Rating
Moisture Sensitivity Level 3 at 260C per JEDEC standard IPC/JEDEC J-STD-020.
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: www.triquint.com Email: info-sales@tqs.com For technical questions and application information: Email: sjcapplications.engineering@tqs.com Tel: Fax: +1.503.615.9000 +1.503.615.8902
Important Notice
The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained herein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. TriQuint products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death.
- 9 of 9 -
Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network