Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
: Date:
1 Input data
Anchor type and diameter: Effective embedment depth: Material: Evaluation Service Report:: Issued I Valid: Proof: Stand-off installation: Anchor plate: Profile: Base material: Reinforcement: ETA 98/0001 17-06-2011 | 19-02-2013 design method ETAG No. 001 Annex C(2010) eb = 0 mm (no stand-off); t = 20 mm lx x ly x t = 530 mm x 400 mm x 20 mm; (Recommended plate thickness: not calculated) IPEo; (L x W x T x FT) = 364 mm x 172 mm x 15 mm x 15 mm cracked concrete, C20/25, fcc = 25.00 N/mm2; h = 250 mm no reinforcement or reinforcement spacing >= 150 mm (any ) or >= 100 mm ( <= 10 mm) no longitudinal edge reinforcement Reinforcement to control splitting according to ETAG 001, Annex C, 5.2.2.6 present. Geometry [mm] & Loading [kN, kNm] HST M20 hef = 101 mm, hnom = 140 mm
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
y 4
Tension
Compression
3.3 Concrete Breakout Strength Ac,N [mm2] 173619 ec1,N [mm] 0 N0 [kN] Rk,c 36.541 A0 [mm2] c,N 91809 yec1,N 1.000 gM,c 1.500 ccr,N [mm] 152 ec2,N [mm] 0 NRd,c [kN] 46.069 scr,N [mm] 303 yec2,N 1.000 NSd [kN] 17.050 ys,N 1.000 yre,N 1.000 k1 7.200
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
4.1 Steel Strength (without lever arm) VRk,s [kN] 84.000 4.2 Pryout Strength Ac,N [mm2] 345519 ec1,V [mm] 0 N0 [kN] Rk,c 36.541 A0 [mm2] c,N 91809 yec1,N 1.000 gM,c,p 1.500 ccr,N [mm] 152 ec2,V [mm] 0 VRd,c1 [kN] 229.203 scr,N [mm] 303 yec2,N 1.000 VSd [kN] 4.000 k-factor 2.500 ys,N 1.000 yre,N 1.000 gM,s 1.250 VRd,s [kN] 67.200 VSd [kN] 1.000
bV 0.017
a 1.500
Status OK
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this calculation! The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
7 Warnings
To avoid failure of the anchor plate the required thickness can be calculated in PROFIS Anchor. Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the loading! Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software considers that the grout is installed under the anchor plate without creating air voids and before application of the loads. The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of ETAG 001, Annex C! For larger diameters of the clearance hole see Chapter 1.1. of ETAG 001, Annex C!
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
8 Installation data
Anchor plate, steel: Anchor type and diameter: HST, M20 Profile: IPEo; 364 x 172 x 15 x 15 mm Installation torque: 0.240 kNm Hole diameter in the fixture: df = 22 mm Hole diameter in the base material: 20 mm Plate thickness (input): 20 mm Hole depth in the base material: 140 mm Recommended plate thickness: not calculated Minimum thickness of the base material: 200 mm Cleaning: Manual cleaning of the drilled hole according to instructions for use is required. 8.1 Required accessories Drilling Suitable Rotary Hammer Properly sized drill bit Cleaning Manual blow-out pump y Setting Torque Wrench Hammer
265
265
50 300 200
2 50
130
270
130
Coordinates Anchor [mm] Anchor 1 2 3 4 x -135 135 -135 135 y -150 -150 150 150 c-x c+x c-y c+y -
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
200
www.hilti.in Company: Specifier: Address: Phone I Fax: E-Mail: Page: Project: Sub-Project I Pos. No.: Date:
Input data and results must be checked for agreement with the existing conditions and for plausibility! PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan