Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
-- Note: SI units
Competitors please replace the sample specification values in the table below with those appropriate for your vehicle and submit this to with your design report. This information will be reviewed by the design judges and may be referred to during the design event. --Please do not modify format of this sheet. Common formatting will help keep the judges happy! --The sample values are fictional and should not be used as the baseline for your designs.
Tire Size and Compound Type Wheels (width, construction) Center of Gravity Design Height Suspension design travel Wheel rate (chassis to wheel center) Roll rate (chassis to wheel center) Sprung mass natural frequency Jounce Damping Rebound Damping Motion ratio / type Camber coefficient in bump (deg / m) Camber coefficient in roll (deg / deg) Static Toe Static camber and adjustment method Front Caster and adjustment method Front Kingpin Axis Kingpin offset and trail Static Akermann and adjustment method Anti dive / Anti Squat Roll center position static Roll center position at 1g lateral acc Steer location, Gear ratio, Steer Arm Length Brake System / Hub & Axle Rotors Master Cylinder Calipers Hub Bearings Upright Assembly Axle type, size, and material
Ergonomics Driver Size Adjustments Seat (materials, padding) Driver Visibility (angle of side view, mirrors?) Shift Actuator (type, location) Clutch Actuator (type, location) Instrumentation 96247504.xls.ms_office V1
Fixed seat and steering wheel. Pedals adjust fore and aft 75mm from center position Wet lay-up carbon, padded lumber and knee protection, 80mm foam head support 210 degree side visibility, 60 x 100mm side mirrors rigidly mounted to nose Manually actuated lever/ linkage, right side cockpit mount Foot pedal, cable actuated Dash mounted temp/oil gauge, 5 LED tach/shift light 1 5/9/2012
Frame Frame Construction Material Joining method and material Targets (Torsional Stiffness or other) Torsional stiffness and validation method Bare frame weight with brackets and paint Crush zone material Crush zone length Crush zone energy capacity Powertrain Manufacture / Model Bore / Stroke / Cylinders / Displacement Compression ratio Induction (natural or forced, intercooled) Throttle Body / Mechanism Fuel Type Max Power design RPM Max Torque design RPM Min RPM for 80% max torque Fuel System (manf'r, and type) Fuel System Sensors (used in fuel mapping) Fuel Pressure Injector location Intake Plenum volume and runner length(s) Exhaust header design Effective Exhaust runner length Ignition System Ignition Timing Oiling System (wet/dry sump, mods) Coolant System and Radiator location Fuel Tank Location, Type Muffler Other significant engine modifications Drivetrain Drive Type Differential Type Final Drive Ratio Vehicle Speed @ max power (design) rpm 1st gear 2nd gear 3rd gear 4th gear 5th gear 6th gear Half shaft size and material Joint type
Frt and rear Tubular space frame / AL Monocoque mid section 1020 and 4130 steel round tubing 40mm dia / 2024-t3 .031" thk Al sheet Fusion welding ER70-S6 filler / 2 part room temp cure epoxy 6000 N-m / deg 6500 N-m/deg CAE beam model, 5700 N-m/deg physical test 50 kg closed cell PVC, aramid composite casing 150mm FEA -- 8200 Joules, physical test -- 9680 Joules
Aerodynamics (if applicable) Type / Configuration Front-Main Element fixed, adj. multi-element flaps, Rear 3 Element, undertray Total Downforce and Drag ( scale using incl. Downforce =212 N, Drag =180 N note ) Aero Balance (% Front, at v=115kph) 45 % front Noteable Features (unsprung mounted, active, etc) lizard skin over hand carved oak structure Optional Information Body Work? Special Bit A? Special Bit B?
3 piece carbon latex body, 2.6 kg complete w/ paint GPS with 'Cartman' voice navigation "Dukes of Hazzard" paint scheme
96247504.xls.ms_office V1
5/9/2012
96247504.xls.ms_office V1
5/9/2012