Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Format For Instruction Plan [for Courses with Labs Course No ECE306 Course Category Cours Title UNIFIED ELECTRONICS LABORATORY-IV Courses with skill focus Course Planner 14907 :: Kranthi Kumar Pulluri Lectures Tutorial Practical Credits 0 0 4 2
Text Book:
1 LMECE306
Other Specific Book: Other Reading Sr No Jouranls atricles as compulsary readings (specific articles, Complete reference)
Relevant Websites Sr. No. (Web adress) (only if relevant to the courses) Salient Features
List of experiments :Lecture Number Individual 1 Lecture Topic Pedagogical Tools Or Equipment Planned lab Manual Not Applicable
Perform the following using 8085 Microprocessor kit in 8085 Microprocessor Kit, Keyboard assembly language. a) Write a program to add two 8-bit numbers. (Or) Write a program to add two 16-bit numbers. b) Write a program to subtract two 8-bit numbers. (Or) Write a program to subtract two 16-bit numbers. c) Write a program to multiply two 8 bit numbers by repetitive addition method. (Or) Write a program to multiply two 8 bit numbers by rotation method. d) Write a program to generate Fibonacci series.
Individual 2 Individual 3
Interfacing of Seven segment display with 8085 microprocessor. Interfacing and control of stepper motor using 8085 microprocessor.
8085 Microprocessor Kit, Keyboard, Seven segment Not Applicable LED, 10K resistor, Power Supply. 8085 Microprocessor Kit, Motor Driver & Stepper Motor Not Applicable
Individual 4
Interfacing of D/A converter with 8085 microprocessor. 8085 Microprocessor, DAC0800, 5K (2), 10K (2), 0.1uF (2),0.01uF. Design a 8085 Microprocessor based Traffic light control 8085 Microprocessor, 10K (9),Led(9)
Not Applicable
Individual 5 Individual 6
8051 Assembly language programming using Keil Keil Simulator compiler. (At least 5 programs.). a. Find the sum of the values 79H, F5H, E2H. Put the sum in register R0 (low byte) and R5 (high byte). b. Write a program to copy the values 55H into RAM memory locations 40H to 45H using i) Direct addressing mode ii) Register indirect addressing mode without using loop iii) With a loop c. Write a program to toggle all the bits of P1 after some delay d. Write a program to generate square wave of 50% duty cycle on bit 0 of port 1 e. Write a program to i) Make P1 as input port. ii) To get hex data from P1 and convert it into decimal and save the digits in R7, R6, R5. f. Write a program to add two 16 bit numbers 3CE7H and 3B8DH. Place the sum in R7 and R6 (Lower Byte). g. A switch is connected to P1.7. Write a program to check the status of SW and perform the following: i) If SW=0, send letter N. to P2. ii) If SW=1, send letter Y. to P2. h. Write a program for Hex to ASCII conversion i. Write a program to generate square wave using timer
Mid Term
Individual 7 Interfacing of LCD with8051 Micro-controller 8051, 11.0592MHz Crystal, 30pF (2), 10uF, 10K, push button, LCD (16x2), 10K Pot. 8051, 11.0592MHz Crystal, 30pF (2), 10uF, 10K, button, ADC0808, 10K Pot, 10K, 150pF. Not Applicable
Individual 8
Not Applicable
Individual 9
8051, 11.0592MHz Crystal, 30pF (2), 10uF, 10K, push button, DAC0800, 5K (2), 10K (2), 0.1uF (2), 0.01uF. 8051, 11.0592MHz Crystal, 30pF (2), 10uF, 10K, push button(4), LCD (16x2), 10K Pot. 8051, 11.0592MHz Crystal, 30pF (2), 10uF(5), 10K, push button, LCD (16x2), 10K Pot, Max232, RS232 Cable
Not Applicable
Individual 10
Not Applicable
Individual 11
Not Applicable
Spill Over
Individual 12 Revision. Not Applicable