Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
tp
://
Acer X233HZ&X243HQ Service Guide
1
ww
w. wj
el.
ne
ht
tp
://
2
ww
w. wj
el.
ne
Copyright Copyright 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, Transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
Disclaimer The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
Intel is a registered trademark of Intel Corporation. Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
Trademarks
Conventions
Gives bits and pieces of additional information related to the current topic.
ht
tp
Alerts you to any damage that might result from doing or not doing specific actions. Gives precautionary measures to avoid possible hardware or software problems.
://
Screen messages
ww
3
w. wj
el.
ne
Preface
Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office may have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details.
2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
provided by your regional Acer office to order FRU parts for repair and service of customer machines.
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibility of the user to correct such interference. As ENERGY STAR Partner our company has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Warning: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerous high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
ht
tp
://
ww
4
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
w. wj
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
el.
ne
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list
Precautions
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, uses a mounting kit approved by the manufacturer and follow the kit instructions. Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit
have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock. Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel
configured receptacles marked between 100 - 240V AC, Min. 5A. The wall socket shall be installed near the equipment and shall be easily accessible.
The following symptoms are normal with LCD monitor and do not indicate a problem.
Notes Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time. Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. 5
ht
tp
://
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
ww
w. wj
el.
only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,
ne
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of
Table Of Contents
Chapter 1 Monitor Features Introduction Electrical Requirements LCD Monitor General Specification LCD Panel Specification Factory Preset Timing Monitor Block Diagram Main Board Diagram Software Flow chart Main Board Layout Installation Chapter 2 Operating Instructions External Controls Front Panel Controls eColor Management (OSD) How to Adjust a Setting 7 7 8 9 10 13 14 15 16 18 19 21 21 21 22 23 27 27 28
How To Optimize The DOS-Mode Enter into the factory mode Chapter 3 Machine Disassembly
Chapter 4 Chapter 5
Troubleshooting
ww
w. wj
6
el.
ne
31 37
Connector Information
Chapter 7
ht
Exploded Diagram
tp
Chapter 6
://
38 38 43
Schematic Diagram
Monitor Features
Introduction
Scope
Chapter 1
This short specification describes the electrical, optical and functional performance requirements for a 63.2cm (23.6) TFT LCD color monitor with VGA&DVI compatible interface.
Description The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF target is 50k hours or more.
Chart of X233HZ&X243HQ
Panel Signal Interface Sync Type Color Temp User Adjust DDC Speaker
M236H1-L01 NB CMO
Headphone Jack
://
Tilt / Swivel
ht
tp
ww
No No 7
w. wj
Support DDC2B Yes support Yes /No
el.
ne
Warm up time AC supply voltage Ambient temperature Humidity Display mode e-color mode
30 min. 230V 5, 50 3 Hz 20C 5C 65% 20% 1920 x 1080, 60 Hz, Pixel Clock148.5MHZ,all white Set to User mode Set to The value under user mode, which allows that the brightest two of 32 linear distributed gray-scales (0 700mv) can be distinguished. 6500 K The value under user mode 700 mVss Factory preset value, 90 H and V
Color temperature Brightness control Analog Input signal Picture position and size Viewing angle Viewing distance Ambient illumination
40 cm for LCD performance, 20 cm for LCD failures Dark room < 1 cd/m2
Measurement systems
Degrees F = [ x 1.8] + 32 C Degrees C = [ - 32]/1.8 F u' = 4x/(-2x + 12y + 3) v' = 9y/(-2x + 12y + 3)
x = (27u'/4)/[(9u'/2) - 12v' + 9] y = (3v')/[(9u'/2) - 12v' + 9] nits = cd/(m2) = Ft-L x 3.426 lux = foot-candle x 10.76
ht
tp
://
ww
8
w. wj
el.
ne
Contrast control
Model name
X233HZ&X243HQ Driving system Active Display Area Pixel pitch TFT Color LCD 525.22 (H) x 297.22(V) 0.2715(H) x 0.2715(V) 1000 : 1 (typ) 5ms(Typ.). 8ms(max)
LCD Panel Contrast Ratio Response time Luminance of White Separate Sync. Input H-Frequency V-Frequency Viewing angle Display Colors Display mode (H)90 16.7M (V) 90(Type)
OFF Mode
:// tp
Contrast control
Set to The value under user mode, which allows that the brightest two of 32 linear distributed gray-scales (0 700mv) can be distinguished. 100 V ~ 240 V50 3Hz, 60 3Hz
Power Source
Environmental Considerations
Operating Temp: 0 to 40 C Storage Temp: -20 to 60 C Operating Humidity: 15% to 90% Storage Humidity: 15% to 90% Operating Altitude: 12,000 feet (3,658m) Storage Altitude: 40,000 feet (12,192m)
ht
< 55A peak at 240 VAC and cold starting No advance effects (no loss of information or defect)
ww
9
w. wj
< 65W < 1W
el.
ne
General Specifications
Block Diagram
TFT LCD Module
ht
tp
://
10
ww
w. wj
el.
ne
Electrical Characteristics
ht
tp
://
11
ww
w. wj
el.
ne
Optical Specifications
ht
tp
://
12
ww
w. wj
el.
ne
Mode
Resolution 640x480@60Hz
Total 800 x 525 832 x 520 1024 x 625 1056 x 628 1040 x 666 1344x806 1328x806 1600 x 900 1800 x 1000 1650 x 750
VGA 640x480@72Hz 800x600@56Hz SVGA 800x600@60Hz 800x600@72Hz 1024x768@60Hz XGA 1024x768@70Hz 1152x864@70Hz VESA 1280x960@60Hz 1280x720@60Hz SXGA WXGA 1360x768@60Hz WXGA+ WSXGA+ 1440x900@60Hz 1680x1050@60Hz 1600x1200@60Hz 1920x1080@60Hz UXGA 1920x1080@60Hz 1920x1080@60Hz 1280x1024@60Hz 1280x800@60Hz
N P
ne
70.069 75.000 60.000 59.940 60.020 59.810 60.015 59.887 59.954 60.000 59.963 60.000 69.934 70.087 66.667 57.67 60.000
el.
P P P P P N N P N N P N N N N
w. wj
63.981 49.702 47.712 55.935 65.290 75.000 67.158 67.500 66.587 IBM MODES 31.469 MAC MODES 35.000 31.199 37.320 13
44.955
ww
1904 x 931
2240 x1089
://
DOS
ht
720x400@70Hz
tp
900 x 449
t
N P P P P N P P P P P N N P N P N
28.322
VGA
640x480@67Hz
864x525
30.240
ACER SPECIAL MODE 648x500@57.67 Hz 1024x600@60Hz 808 x 541 1312 x 622 25.209 48.964
CCFL Drive.
USB board
Key board
DVI Signal
ht
tp
://
14
ww
w. wj
el.
AC-IN 100V-240V
ne
D-SUB Signal
Power Board
Main Board
ht
tp
:// w
ww
D-Data D-Clock
.w j
(U401) H sync V sync RGB D-Sub Connector (CN101) 15
Scalar IC NT68667UFG/C
el.
ne t
Key control Interface (CN402)
Y 2 3 N
N
4
N Y 6
ww
10
://
N
w. wj
7 8 Y
Y 9
N 11
Y N 12 Y 14 15 Y 17 13 Y N 16
ht
tp
N 18
19 Y
16
el.
ne
Remark:
1) MCU initializes. 2) Is the EEPROM blank? 3) Program the EEPROM by default values. 4) Get the PWM value of brightness from EEPROM. 5) Is the power key pressed? 6) Clear all global flags.
8) Enter factory mode. 9) Save the power key status into EEPROM. Turn on the LED and set it to green color. Scalar initializes. 10) In standby mode? 11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming? 13) Does the scalar send out an interrupt request? 14) Wake up the scalar.
message disappears.
17) Program the scalar to be able to show the coming mode. 18) Process the OSD display. 19) Read the keyboard. Is the power key pressed?
ht
tp
16) Display "No connection Check Signal Cable" message. And go into standby mode after the
://
ww
17
w. wj
el.
ne
Description
tp
://
Symbol CN402 CN701 CN301 X401 CN101 CN102 Description WAFER WAFER 9P RIGHT ANELE PITCH CONNECTOR CRYSTAL 12MHz HC-49US ARG6-120 D-SUB 15PIN VERTICAL CONN WITH SCREW DVI 24PIN CONN F IC LD1117DT33TR IC AZC099-04S SOT23-6L IC AZC099-04S SOT23-6L SST25VF010A-33-4C-SAE IC AZ1117D-1.8-E1
ht
ww
18
w. wj
el.
ne
Installation
To install the monitor to your host system, please follow the steps as given below: Steps 1. 1-1 Connect Video Cable a. Make sure both the monitor and computer are powered-OFF. b. Connect the VGA video cable to the computer. 1-2 Digital Cable (Only Dual-Input Model) a. Make sure both the monitor and computer are powered-OFF. b. Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computers port. Steps 2. Connect power cord Connect the power cord to the monitor, then to a properly grounded AC outlet.
Steps 4. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem.
ht
tp
://
19
ww
w. wj
el.
ne
Power-ON the monitor first, then power-ON the computer. This sequence is very important.
Remove:
Depress the release button as indicated first before removing the base and follow the arrow direction to remove it.
In oder to optimize the best viewing position, you can adjust the tilt of the monitor by using both of your hands to hold the edges of the monitor as shown in the figure below. The monitor can be adjusted to 15 degrees up or 5 degrees down as indicated by arrow below.
ht
tp
://
ww
20
w. wj
el.
ne
Operating Instructions
monitor. By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. Connect the video cable from the monitor to the video card. Press the power button to turn on the monitor position. The power indicator will light up.
Chapter 2
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
External Controls
Lights up to indicate the power is turned ON. 1) When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). 2) When OSD menu is in off status, press this button to select scenario mode. 1) When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). 2)When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function .The Auto Adjustment function is used to set the Hpos, Vpos, Clock and Focus. 3) When exit eColor OSD, it will activate the Auto Adjustment function Press < or > to select the desired function. Press < or > to change the settings of the current function. Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON.
3.Empowering / Exit
5.< / >
6.MENU / ENTER
ht
tp
://
ww
21
w. wj
el.
ne
Operation instructions
Acer eColor Management Step 1: Press
Key to open the Acer e-Color Management OSD and access the scenario modes
Automatic Adjustment
ht
tp
://
22
ww
w. wj
el.
ne
If selected to Acer eColor Management item, will appear the Acer eColor OSD. OSD and Key locations
USER
ht
tp
://
23
ww
w. wj
el.
ne
ht
tp
://
24
ww
w. wj
el.
ne
ht tp :// ww w. wj el. ne t
25
ht tp :// ww w. wj el. ne t
26
How To Optimize The DOS-Mode Plug And Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bi-directional data channel based on the IC protocol. The host can request EDID information over the DDC2B channel.
This monitor will appear to be non-functional if there is no video input signal. In order for this monitor to operate properly, there must be a video input signal.
This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA) and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no
automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a "Screen Saver" feature except the display is completely off. Pressing a key on the keyboard, or clicking the mouse restores the display.
The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 volts AC. Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, and CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties.
Turn off the power, press the e-color and turn the power on. The factory OSD will be at the left top of the panel.
ht
tp
://
ww
27
w. wj
el.
video-input signal present. When there is no video input signals this monitor, following a time-out period, will
ne
Machine Disassembly
HQ monitor for maintenance.
The tool for disassembly is as follows:
Screwdriver,Hexagonal screwdriver, Putty knife.
Chapter 3
Disassembly Procedure
1. Remove the hinge assembly.
2.
The arrows in blue are the hook that we should put attention to when remove the rear cover. Use plastic putty knife to release hooks, then you can easily remove the rear cover.
ht
tp
://
ww
28
w. wj
el.
ne
3 Remove the lamp connectors and remove the screws to remove the panel. Put attention to the LVDS cable.
4.
Remove the screws to remove the main board and power board.
ht
tp
://
29
ww
w. wj
el.
ne
5. The panel
ht tp :// ww w. wj el. ne t
30
Troubleshooting
1. No Power
Chapter 4
No power
OK
NG
OK
ww
OK 31
NG
Replace X401
ht
tp
://
NG Replace U401
w. wj
Check U703, C706 and C707
el.
ne
No picture
NG
NG Replace X401
OK OK Check reset circuit of U401 is normal Measure U703 Pin2=3.3V, OK Replace U401 OK NG NG Check Correspondent component
OK
ht
tp
Replace U401
://
ww
NG 32
w. wj
Replace X401 Check Correspondent component
el.
ne
White screen
OK
NG
Replace X401
OK
ht
tp
://
ww
33
Replace PANEL
w. wj
OK
NG
el.
NG Replace U401
ne
Check Correspondent component.
4. Key Board
ht
tp
://
34
ww
w. wj
el.
ne
Replace Key Board
5. Power Board
1) No power
OK
OK
NG
NG OK
Check the auxiliary voltage is bigger than 11V and smaller than 25V
://
OK
ww
NG 1) Check IC901 2) Check R909/D901/C908/C907circuit NG Check IC901 35
Check D906/D907/D908/IC903/Q903/ZD902
ht
tp
OK
w. wj
el.
ne
2.) No Backlight
OK
OK
OK
://
NG
ht
tp
OK
ww
NG Check R816/R817/R818/R819 Change PT801 36
w. wj
Change IC801
el.
NG
ne
Connector Information
D-sub connect and DVI connect:
Chapter 5
ht
tp
://
37
ww
w. wj
el.
ne
Chapter 6
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of X233HZ&X243HQ. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel (http://aicsl.acer.com.tw/spl/). For whatever reasons a part number change is made, it will not be noted in the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
ht
tp
://
38
ww
w. wj
el.
ne
how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 SCERW M3X8 SCERW M4X8 SCERW M4X10 SCERW M4X8 SCERW M3X5 SCERW M3X6 RUBER FOOT 2 RUBER FOOT 1 BAES BRACKET HINGE HINGE COVER R HINGE COVER L BASE BUTTON BASE STAND REAR STAND FRONT REAR COVER PW-SHIELD MAIN FRAME KEY BUTTON LED LENS BEZEL
Description 0Q1G130 0M1G140 0M1G1740 0Q1G 940 0M1G 130 0M1G1730 A12G0006 1 A12G0007 1
Q`ty 6 4 3 1 2 6 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1
A15G0567 101 A37G0110 1 A33G0271 RX 2L0200 A33G0271 RX 1L0200 A33G0266 RX 1L0100 A34G1109 RX 1B0130 A34G1108 RX 1B0100 A34G1106 RX 1B0100 A15G0478201 A15G0477F01101
A34G1107 RX 1B0100
ht
tp
://
39
ww
w. wj
A33G0270
A34G1105 RXA1B0130
el.
ne
Part List Above picture show the description of the following component.
Picture
Description
Part No.
Main_frame_Sam
A15G0477F01101
Bezel
:// ht tp
ww
Panel 750GLM236H1112N000 Power Board PWPC8E41MQHA 40
w. wj
el.
ne
A34G1105 RXA1B0130
Main Board
CBPCRNDABQP
Key Board
KEPC7QK1
w. wj
Stand Front
:// ht tp
41
ww
Base A34G1109 RX 1B0130 Stand Rear A34G1108 RX 1B0100
el.
A34G1107 RX 1B0100
ne
Hinge
A37G0110
ht
tp
://
ww
42
w. wj
el.
ne
USB BOARD
USB7QK4
Schematic Diagram
Main Board
FB102 VGA_B+ H_Sy nc R102 V_Sy nc E5VCC R106 2K2 1/16W 5% R107 2K2 1/16W 5% C103 C104 VGA_B5V_ESD DSUB_SDA R143 4K7 1/16W 5% 100R 1/16W 5% R101 R144 4K7 1/16W 5% 16 CN101 DSUB_5V 10 5 9 4 8 3 7 2 6 1 17 DB15 VGA_PLUG DSUB_5V VGA_BVGA_B+ VGA_GVGA_G+ VGA_RVGA_R+ C112 AZC099-04S NC DSUB_SCL 6 5 4 U104 I/O4 I/O1 VDDGND I/O3 I/O2 1 2 3 H_Sy nc V_Sy nc R109 100R 1/16W 5% 22pF 22pF 0R05 1/10W 5% R103 1K 1/16W 5% R104 1K 1/16W 5% DSUB_H DSUB_V 1 BEAD R108 75R 1/16W 5% C106 0.047uF C107 1000pF C108 0.047uF C105 5pF/50V 2 R105 100R 1/16W 5% C102 0.047uF
Chapter 7
DSUB_B+
ne t
FB103 BEAD VGA_G+ 1 2 R112 VGA_GFB101 2 BEAD R116 VGA_R+ 1 VGA_RESD_5V 1 R137 4K7 1/16W 5% DVI_SCL DVI_SDA R121 R122 DDC_WP ( Top Victory Electronics Co . , Ltd. ) G3108-D-X-X-1-20080519 2.0.INPUT Thursday , May 22, 2008 Sheet
DSUB_B-
DSUB_SOG DSUB_G+
DDC1_SCL
DSUB_SCL 15 14 13
DDC1_SDA
ZD104 RLZ5.6B
ZD105 RLZ5.6B VGA_R+ VGA_G+ 3 2 1 U103 I/O2 I/O3 GNDVDD I/O1 I/O4 AZC099-04S 4 5 6
VGA_B+
el.
5V_ESD
U1 03
R115
100R 1/16W 5%
.w j
C101 NC
C111 0.047uF
DSUB_R+
VGA_DET
R141
1K 1/16W 5%
U1 01
75R 1/16W 5%
R139 CN102 VSY NC SY NC GND DDC SCL DDC SDA +5V HPD 1/3shield 2/4shield 0/5shield clk shield DAT0+ DAT0DAT1+ DAT1DAT2+ DAT2DAT3+ DAT3DAT4+ DAT4DAT5+ DAT5clk+ clk8 15 6 7 14 16 11 3 19 22 18 17 10 9 2 1 13 12 5 4 21 20 23 24 ESD_5V U107 4 5 6 I/O3 I/O2 VDDGND I/O4 I/O1 AZC099-04S 3 2 1 DVI_HPD
1K 1/16W 5% DVI_5V
DVI_DET
ww
R118 100R 1/16W 5% R119 100R 1/16W 5% DDC2_SCL DDC2_SDA HDCP_CTRL
:// w
R126 R127 R128 R129 R130 R131
5VCC
GND GND
tp
R132 R134
RXCP RXCN
R136 NC/4K7 1/16W 5% R138 4K7 1/16W 5% NC/100R 1/16W 5% NC/100R 1/16W 5%
C117 0.1uF/16V
26 25
JACK
ESD_5V
ESD_5V
C120 NC
ht
1 2 3
6 5 4
1 2 3
NC / M24C02-WMN6TP
C118 NC
C119 NC
U1 0 7
U1 05
U1 06
GND POWER DGND TPV OEM MODEL Acer X243HQ&X233HZ TPV MODEL PCB NAME 2 of 5 TDRMNDD8Y 1ABPN Size Rev B 1 <>
Key Component
Date
43
CN301 T0M T0P T1M T1P T2M T2P TCLK1M TCLK1P T3M T3P T4M T4P T5M T5P 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
C302 0.1uF/16V
.w j
Q301 AO3401
C303 R307 47K 1/16W 5% PPWR_ON# Q302 2N3904S-RTK/PS R306 10K 1/16W 5% C306 0.1uF 16V C304 NC NC
ww
el.
PANEL_VCC R305 0 OHM +-5% 1/8W + C305 100uF25V
+5V
ne t
T6M T6P TCLK2M TCLK2P T7M T7P PANEL_VCC R301 330 OHM 1/4W C301 0.1uF/16V Co . , Ltd. ) OEM MODEL Acer X243HQ&X233HZ TPV MODEL PCB NAME Sheet 3 of 5 TDRMNDD8Y 1ABPN Size Rev
CONN
ht
tp
AO3401L
:// w
3D 1 G 2 S
T P V ( Top
Victory
Electronics
A 1 <>
Key Component
Date
44
5VCC CN701 1 2 3 4 5 6 7 8 9 +5V +5V +5V BKLT-VBRI BKLT-EN R710 R703 R707 NC 4K7 1/16W 5% 4K7 1/16W 5% PANEL_ID# Volume# Mute SM340A D701 5VCC R701 NC
CONN
lock type
C701 NC
C703 NC
C710 NC
DSUB_5V
ne t
3 C711 5VCC U701 3 VIN VSS 100uF25V 0.1uF/16V 1 + C706 C708 U703 3 2 1
VCC1.8
el.
+ C704 NC/100uF25V
E5VCC
NC/0.1uF/16V
VCC3.3
.w j
5VCC
NC/0.1uF/16V
R705 VCC3.3 BKLT-VBRI R702 10K 1/16W 5% BKLT-EN C702 NC R704 on_BACKLIGHT Q701 4K7 1/16W 5% 2N3904S-RTK/PS R706 1K 1/16W 5% 10K 1/16W 5%
VOUT
adj_BACKLIGHT
ww
NC/AP1117E33LA
:// w
AP1117D33LA
ht
tp
T P V ( Top
Key Component
Victory
Electronics
Co . ,
Ltd. )
OEM MODEL Acer X243HQ&X233HZ TPV MODEL PCB NAME Sheet 4 of 5 TDRMNDD8Y 1ABPN
Size Rev
B 1 <>
Date
45
FB401 300OHM
AVCC
FB406 300OHM
PVCC
VCC1.8
FB403 300OHM
CVDD DVDD
C403 0.1uF/16V
C404 0.1uF/16V
C448 0.1uF/16V
C406 0.1uF/16V
C407 0.1uF/16V
C442 0.1uF/16V WP R409 C401 0.22uF16V 100R 1/16W 5% R414 10K 1/16W 5% SPI_CE SPI_SO U402 1 2 3 4 CE VCC SO HOLD# WP# SCK GND SI PM25LV010A 8 7 6 5
FB404 300OHM
SPI_CK SPI_SI
DVDD
AVCC C438 CVDD 1uF/16V C413 ADC_VAA 0.1uF/16V C410 0.1uF/16V C412 0.1uF/16V C430 0.1uF/16V C423 0.1uF/16V 52 115 119 45 43 26 6 15 17 R401 470 OHM +-1% 1/16W 16 4 5 7 8 10 11 13 14 41 42 19 20 21 22 23 24 25 U401 REXT RX2+ RX2RX1+ RX1RX0+ RX0RXC+ RXCHSY NCI1 VSY NCI1 BIN1+ BIN1SOG1I GIN1+ GIN1RIN1+ RIN1PVCC
DVDD
ADC_VAA
PLL_GND
PLL_VDD
AVCC AVCC
PVCC
FB407 300OHM
ADC_VAA
AVCC
51 53 90 2
DVDD DGND/CGND DGND/CGND DGND/CGND DGND/CGND DGND/CGND DGND/CGND DGND/CGND DGND/CGND DGND/CGND DGND/CGND RSGB1M/T0M RSGB1P/T0P RSCLKBM/T1M RSCLKBP/T1P RSBB3M/T2M RSBB3P/T2P RSBB2M/TCLK1M RSBB2P/TCLK1P RSBB1M/T3M RSBB1P/T3P RSRA3M/T4M/RSRB0M RSRA3P/T4P/RSRB0P RSRA2M/T5M/GSGB0M RSRA2P/T5P/RSGB0P RSRA1M/T6M/RSGB0M RSRA1P/T6P/RSBB0P RSGA3M/TCLK2M RSGA3P/TCLK2P RSGA2M/T7M RSGA2P/T7P DGND/CGND RSGA1P/VCKI RSCLKAM/V7 RSCLKAP/V6 RSBA3M/V5 RSBA3P/V4 RSBA2M/V3 RSBA2P/V2 RSBA1M/V1 RSBA1P/V0 100 99 98 97 96 95 94 93 92 91 88 87 86 85 84 83 82 81 80 79 77 76 75 74 73 72 71 70 69 68 63 62 61 60 59 58 57 56 55 54
C447 0.1uF/16V
ne t
R440 4K7 1/16W 5% EE_WP MSCL MSDA VSO HSO adj_BACKLIGHT Volume# POWER_KEY # EE_WP on_BACKLIGHT PANEL_ID# DDC_WP HDCP_CTRL PPWR_ON# R443 3.9K OHM 1% 1/16W LED_LF_BLUE C433 0.1uF/16V C434 0.1uF/16V R411 10K 1/16W 5% C435 0.1uF/16V T P V ( Top
K ey Component
RX2P RX2N RX1P RX1N RX0P RX0N RXCP RXCN DSUB_H DSUB_V DSUB_B+ DSUB_BDSUB_SOG DSUB_G+ DSUB_GDSUB_R+ DSUB_R-
el.
T4M T4P T5M T5P T6M T6P TCLK2M TCLK2P T7M T7P LED_A R418 R417 120R 1/16W 5% 100R 1/16W 5% LED_B R425 R402 VSO HSO 1K 1/16W 5% 100R 1/16W 5% R421 R422 R406 R419 NC/120R 1/8W NC/120R 1/8W LED_A NC/120R 1/8W LED_ORANGE NC/120R 1/8W 5% LED_B R420 10K 1/8W 5% VCC3.3 R444 3.9K OHM 1% 1/16W
T0M T0P T1M T1P T2M T2P TCLK1M TCLK1P T3M T3P
+5V
NC/10K 1/16W
R465
.w j
89 110 111 112 113 114 116 117 118 103 102 124 123 122 28 121 120 40 39 38 37 36 67 66 65 PC7 PC6 PC5 PC4/PWM1 PC3/PWM0 PC2 PC1* PC0* PA7/PWM9* PA6/PWM8* PA5/PWM7* PA4/PWM6* PA3/PWM5 PA1/PWM3 PA2/PWM4 PA0/PWM2
+5V DDC1_SDA DDC1_SCL DDC2_SDA DDC2_SCL 5V_DET KEY 1 KEY 2 R415 R416 1K 1/16W 5% 1K 1/16W 5% 34 35 46 47 30 33 125 126 PB7/DDC_SDA1* PB6/DDC_SCL1* PB5/DVI_SDA0* PB4/DVI_SCL0* PB3/ADC3/INTE1 PB2/ADC2/INTE0 PB1/ADC1 PB0/ADC0
Q401 NC/2N3906S-RTK/PS LED_LF_BLUE R468 NC/0R05 1/16W +5V 2K2 1/16W 5% 0R05 1/8W 1 R471 NC 3 2 Q402 2N3906S-RTK/PS R472 LED_GRN/BLUE 120R 1/16W 5%
R469
R470
C446 0.1uF/16V
49 50 31 32 1
RSTB OSCI
C422 0.1uF/16V
C420 22pF
DUBUG
tp
44 3 109 64 78 101 18 12 9 27
NT68667FG
:// w
GND DGND GND DGND/CGND DGND/CGND DGND/CGND PGND AGND AGND ADC_GNDA
ww
ht
CONN
C432 0.1uF/16V
CN401
CN406 NC/CONN
POWER_KEY# KEY 1 KEY _LEFT KEY _RIGHT KEY 2 KEY _AUTO LED_LF_BLUE
1 2 3 4 5 6 7 8
1 2 3 4 5
FFC CONNECTOR
NC/2x4PIN/1.0mm
Victory
Electronics
Co . ,
Ltd. )
OEM MODEL Acer X243HQ&X233HZ TPV MODEL PCB NAME Sheet 5 of 5 TDRMNDD8Y 1ABPN
Size Rev
C C <>
Date
46
Power board
L904 100 OHM 1/4W R918 100 OHM 1/4W R919 C912 0.001uF 100 OHM 1/4W R920 FB902 80OHM 1 4 + 2 4 2 2 C917 + 3 + 470UF M 35V Q903 KTD1028 R943 470R 1/8W 5% C932 0.001uF F903 +5V FUSE + R940 NC R939 1K 1/8W 5% D906 FMX-12SL 3 470UF M 35V 1 C918 + Coil +16V 1
!BD901 GBU408
ZD90 2 T ZX18B
!
T901 POWER X'FMR
!
C904
C938 1500PF2KV
R904 8.2K OHM 1/4W R903 C906 1500PF2KV R905 8.2K OHM 1/4W D901 FR103 3 0.1uF C907 + C908 22uF 50V D900 FR107 R909 3.3 OHM 1/4W 100K OMH 2W +-5% 6 1 9 10 12 11 5 8 7
R935 100 OHM 1/4W R961 100 OHM 1/4W L903 C929 R962 100 OHM 1/4W 0.001uF
R946 100OHM 2W
NC
0.22UF275V
!
2 3 L901 27mH
D907 31DQ06FC3
IC901
!
C903
!
C940 0.047uF
1 2 3 4
8 7 6 5
D903
el.
1
ne t
Coil + R924 C939 1000uF/25V C935 0.001uF 1 D908 SP1060 + C916 1000uF/25V C934 NC +
C937 100pF/2KV 4
!
3 2 C924 0.1uF
NC
R925 1K 1/8W 5%
FB901 BEAD
R949 100 OHM 1/4W R950 100 OHM 1/4W R951 100 OHM 1/4W
0.22UF275V R902 1M 1/4W 5% R901 1M 1/4W 5% NR901 NTCR C909 220pF 0.39 OHM 2W +-5% R912 220 OHM 1/4W R914
IC904 KIA431A-AT/P
ww
.w j
R926 1K 1/10W 1% 3
!
C902 1000pF
!
C901 1000pF
:// w
1 2 3 4
NC
CN903
+16V
!
1
CONN
2 CN901 SOCKET
C931 0.1uF
GND2 GND 1 2 1 2
GND1 GND 1 2
tp
HS1 HEAT SINK(Q901) 1 2
CONN
ht
T P V ( Top
K ey Component
Victory
Electronics
Co . ,
Ltd. )
Size Rev
Date
47
R817 4R7 1/8W 5% R816 4R7 1/8W 5% Q805 4 3 2 1 G1 S1 G2 S2 D1 D1 D2 D2 5 6 7 8 PT801 6 POWER X'FMR 7 5 2 1 5 6 7 8 8 CN801 C819 56pF3KV 1 2 HV LV CN802 C820 56pF3KV LV2 1 L801 4 CONN 2 L802 1 L 4 LV4 3 CONN 1 2 HV LV
+5V 1 R803 5K1 1/8W 5% R804 5K1 1/8W 5% C815 0.1uF C802 0.047uF R802 22R 1/8W 5% R805 NC C801 0.047uF R819 4R7 1/8W 5% 4 3 2 1 C811 0.1uF 1
AO4620
DIM PID
Q806 G1 S1 G2 S2 D1 D1 D2 D2
LV1
AO4620
C804 R801 10K 1/10W 5% R807 10K 1/10W 5% 9 10 11 12 13 14 15 16 R815 R808 NC 390R 1/10W 1% C818 R806 100K 1/10W 1% 1.5UF/10V C812 C806 NC 2.2uF/16V C805 0.022uF R813 100K 1/10W 5% R809 1M 1/10W 5% C810 0.0033uF NDR1 NDR2 PDR1 GNDP VDDA PDR2 TIMER GNDA PWM RT1 ISEN CT OVPT SSTCMP ENA VSEN 8 7 6 5 4 3 2 1 R810 100K 1/10W 1% IN4148 D801
el.
ne t
R828 6.2M1W C817 2PF6KV C813 NC C814 220pF R836 56K 1/10W 5% R837 R830 6K8 1/8W 5% 6K8 1/10W 5% R838 1M 1/10W 5% LV1 R839 1M 1/10W 5% LV2 R840 1M 1/10W 5% LV3 R841 1M 1/10W 5% R844 10K 1/10W 5% LV4 R845 10K 1/10W 5% Electronics Co . , Ltd. ) OEM MODEL TPV MODEL PCB NAME Sheet 715G2824-1-5 3 of 4
2 L
3 C821 56pF3KV 1 2
CN803
HV LV CN804 CONN
.w j
C809 220pF D806 BAV70 1
IC801 ta9687GN-A-0-TR
Q802
HV LV CONN
ww
3
D807 BAV70 1
:// w
D808 BAV70 1
D803 BAV99 1 2
3 2
ht
tp
T P V ( Top
Key Component
Victory
Size Rev
Date
48
+5V1 R602 10K 1/10W 5% VOL R603 10K 1/10W 5% C609 1uF/25V 10K 1/10W 5% R609 CN601 4 5 3 2 1 PHONEJACK R606 12KOHM +-5% 1/10W 12KOHM +-5% 1/10W +5V1 R612 10R 1/10W 5% Lin Rin R605 6.2K 1/10W 5% R604 6.2KK 1/10W 5% C601 0.47uF/16V C606 0.47uF/16V IC601 +
ne t
SE/BTL VOLUME LINGND GND RINBYPASS SHUTDOWN LOUTVDD LOUT+ GND GND ROUT+ VDD ROUT9 10 11 12 13 14 15 16 APA2069JITUL C608 1uF/25V Acer X243HQ&X233HZ TDRMNDD8Y1ABPN 715G2824-1-5 4 of 4
0.47uF/16V
2008-08-18 EE MODIFY
LOUT+ LOUTROUTROUT+ CONN 4 3 2 1 CN602
R607
D601
IN4148
:// w
MUTE
tp ht
Q608 MMBT3904
R613 1K 1/10W 5%
ww
C613 + Q607 MMBT3906
C610
C611
.w j
C612 0.1uF/16V R601 10K 1/10W 5% C614 0.1uF/16V
100pF
100pF
el.
8 7 6 5 4 3 2 1
TPV
( Top
Victory
Electronics
Co . ,
Ltd. )
Size Rev
Key Component
Date
49
Key board
LED001 LED 2007/5/18
POWER
el.
2007/5/18 2 5 4
MENU
VOL-
.w j
UDZS5.6B
SW004 SW
C007
ZD004
SW001 SW 3
NC
NC
NC
GND
ww
GND1 G GND-EMI
GND2 G GND-EMI
:// w
CN001
GND
CONNECTOR
ECOLOR AUTO
MENU
VOL-
VOL+
POWER LED
ht
tp
TPV
( Top
Victory
Electronics
Co . ,
Ltd. )
OEM MODEL X173/X173W/X193W/P193W/X223W TPV MODEL PCB NAME Sheet ACER 715G2731-B-AC 1 of 2
NC
Size Rev
Key Component
Date
50
AUTO
VOL+
CONN
ECOLOR
C001 NC
C002 C003 NC NC
C004 NC
C005 NC
R004 R005
ne t
Usb board
U708 VBUS0 C769 1uF/16V R719 100K 1/10W 5% 27 USB2514-AEZG CN710 5 4 3 2 1 30 31 DM0 DP0 R731 CONN USB5V VBUS3 5 CN707 NC 1 6 DM1 DP1 2 3
Upstream
USBUP_DM VBUS_DET USBUP_DP
VBUS1 CN706
Dow nstream 1
USBDN1_DM 13 OCS1 USBDN1_DP PRTPWR1
1 2 12
4 3 2 1
t
VBUS1A1
VBUS1
9 10
5 6 7 8 5 6 7 8 11 12 1 2 3 4 1 2 3 4 VBUS2 USB5V 1
/OC1
Dow nstream 2
USBDN2_DM /OC2 17 OCS2 USBDN2_DP PRTPWR2 3 4 16 DM4 DM2 DP2
ne t
USB5V 1 FB721 VBUS2 F703 PTCR 2 VBUS2A1 2 120 OHM
0R05 1/10W 5%
+ C772 100uF/16V
C770 0.1uF16V
DM2 DP2
2 3
Dow nstream 3
USBDN3_DM /OC3 19 OCS3 USBDN3_DP PRTPWR3 6 DM3
DP4
el.
t
1 ZD709
1 ZD710
Dow nstream 4
R750 NC/10K 1/10W 5% USBDN4_DM /OC4 21 OCS4 USBDN4_DP PRTPWR4 8 9 20 DM4 DP4 R764 NC/10K 1/10W 5% R765 NC/10K 1/10W 5%
VCC3.3V
NC CONN
t
VBUS3A1 +
t
VBUS4A 1 +
VBUS4
C773
.w j
+ C771
0.1uF16V
C776 100uF/16V
C777 0.1uF16V
VCC3.3V
EEPROM/Config
SDA/SMBDATA/NON_REM1 SCL/SMBCLK/CFG_SEL0 HS_IND/CFG_SEL1 22 24 25
8 7 6 5
RESET
Common
RBIAS
35
C7101 0.1uF16V
ww
Power USB
R743 U709 AP1510SA 3K9 1/10W 5% 4 3 2 1 VCC OUTPUT OCSET OUTPUT EN VSS FB VSS 5 6 7 8
D702 SM540A C723 1000PF50V L711 22uH 8K2 1/10W 1% C784 0.1uF16V
+12V +5V
C779 1uF/25V
CN709
+ C778 470uF/25V
C783 0.1uF16V
R744
28
LOCAL_PWR/NON_REM0/SUSP_IND VDD33
C722 0.1uF16V
:// w
5 10 29 36
5 4 3 2 1
R755 10K 1/10W 5% Q711 NC/AO4411 1 2 3 4 R767 R747 NC/33K 1/10W 5% NC/22K 1/10W Q713 S S S G D D D D 8 7 6 5 FB725 1 NC 2 R745 10R 1/10W 5% R751 1K5 1/10W 1%
USB_CTRL
C788 0.1uF16V
C789 0.1uF16V
C790 0.1uF16V
R762 1M 1/10W 5% 2
CONN
tp
VSS(FLAG)
VDDA18PLL
34
C7103 0.1uF16V
C7104 1uF/16V
ht
1 2 3 4
5 2 1 <> 6 A3 C
CN704
3 4
R761
Power Regulator
U710 3 VIN AP1117E33LA 2 VOUT VSS
USB5V
USB CONNECTOR
C793 100uF/16V
C794 0.1uF16V
+ C795 C796 0.1uF16V 100uF/16V T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Acer X243HQ&X233HZ TPV MODEL PCB NAME Sheet 715G3015-C 2 of 2 Size Rev
G3015-C-X-X-3-080806
TO
Main Board
K ey Component
Date
51