Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Instruction manual
IMPORTANT:
Please read the entire manual for complete details on the features, accessories and operation before attempting to use your security system. This Security system must be installed by a qualified technician to ensure proper operation. Do not attempt to install or modify this system yourself as this way void your warranty.
Table of contents
1. 2. 2-1. 3. 4. 5. 6. 7. 7-1. 7-2. 7-3. 7-4. 7-5. 8. 8-1. 8-2. 8-3. 8-4. 8-5. 8-6. 8-7. 9. 9-1. 9-2. 9-3. 9-4. 9-5. 9-6. 9-7. 9-8. 9-9. 9-10. 9-11. 9-12. 9-13. 9-14. 9-15. 9-16. 9-17. 9-18. 9-19. 9-20. 9-21. 9-22. About your system System maintenance Remote battery replacement LCD 2-way configuration 1-way remote description 2-way & 1-way remote function table Standard LCD 2-way icon instructions Programming 2-way remote Disable remote receiving Remote button 1.2.3 on/off Vibrate mode on/off Time adjust mode Alarm clock setting 2-way signal paging features Command Page Alarm Page Page Recognition (Acknowledgement) Check-in range notification (on/off ) Reminder disarm status (Programmable) Vehicle status checking Turn on LCD display back light Standard features To ARM the system Defective Zone Bypass & Alert Auto Reset Arm without siren chirp To DISARM the system Intrusion Alert 2-way LCD Intrusion Alert Disarm without siren chirp Silent arm mode Automatic REARM (programmable) Passive arm (programmable) Panic mode Dual stage shock sensor Remote sensor by pass Car search mode Confort /window close Valet mode Ignition controlled door lock/unlock(programmable) Ch-4: 2nd stage door unlock (programmable) Ch-4: Remote latched (programmable) Passive immobilizer (programmable) Arming without Remote control (programmable)
Page 3 4 4 4 5 5 6 9 9 9 9 10 10 11 11 11 11 12 12 12 12 13 13 13 13 13 14 14 14 15 15 15 15 16 16 16 17 17 17 17 17 17 18 18
-1-
9-23. 9-24. 9-25. 9-26. 9-27. 9-28. 9-29. 9-30. 9-31. 9-32. 9-33. 9-34. 9-35 9-36. 9-37. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
2nd step disarm Remote trunk open CH-5: Dome light supervision CH-5: Arm W/Engine running CH-5: Turbo mode CH-6: Programmable output CH-7: Programmable output Red/black programme (+) input - Reverse warning - Heard light warning - Extra sensor (knock sensor) input Siren chirps ON/OFF (programmab le) Status LED timer Power disconnecting memory Emergency reset switch Emergency disarm (Valet SW & PIN code) Anti car-jacking mode R.f antenna call switch Set your own PIN code Transmitter programming Programme mode features Programme mode table System installation Wiring diagram Central door lock wiring
18 19 19 19 20 20 20 20 20 20 20 21 21 21 21 21 22 23 23 24 24 25 27 28 30
-2-
What is included:
A control module 2-way pager transceiver antenna One 5-button 2-way LCD remote transmitter One 3-button or 4-button random code remote transmitter Dual stage shock sensor High output 6-tone siren (optional) Status LED indicator Valet over-ride switch
*Many require additional parts and/or labor, see store for details
NOTE:
Some of the features described in this manual may required additional parts and/or labor, and may not be included as part of the standard installation of this unit. Additionally, many features of this security system have selectable options that must be activated or programmed during the system's installation. These items will be identified in the following sections. Please discuss these features and any questions you may regarding the installation of this product with your authorized dealer.
-3-
System maintenance
The system requires no specific maintenance other than battery replacement for the remotes.
FULL
REPLACE
EMPTY
To replace the battery, gently pull the battery cover release tab, then slide the door down to expose the battery and remove the expired battery. Place the new battery into the transceiver observing the correct polarity. When power is returned the transceiver will light all icons in the LCD and generate all beeper tones once.
Antenna
Button 1
Button 2 Button 3
R T
BRAKE
LCD display
IMMO
Button 4 Button 5
AM PM
PASS
CALL
AHJ
TR-45
-4-
TX-4R
Step
once once then within 3sec. press once once then within 3sec. press over 2sec together over 2sec.. over 2sec. once after 8sec. of armed once within 8sec. of armed once within 8sec. of armed together over 2sec. once once
Condition
Disarmed & ACC off Disarmed & ACC off Armed Armed Any time ACC ON Armed Armed Armed Armed ACC ON
-5-
System Armed.
System Disarmed.
Silent Armed.
PASS
PASS
Panic mode.
-6-
IMMO
AHJ
Valet mode.
Turbo mode.
-7-
CALL
Alarm clock.
AM
BRAKE
-8-
Beeps 1-beep
-9-
AM/PM indicator
AM PM
12-hour display Minutes display
3. Press button to turn up the numbers. Press button to turn down the numbers. The button may be held down to scroll faster. 4. Press button to exit the setting mode. 2 beep will be heard. Note: The remote will revert to normal operation from the set mode when 10-seconds has elapsed without a button entry.
AM PM
2. Press button to select Hour & Min adjust setting. Icon flashing to indicate.
3. Press button to turn up the numbers. Press button to turn down the numbers. The button may be held down to scroll faster. 4. Press button to enable the alarm clock. 1 beep will be heard and exit the mode. Press button to disable the alarm clock. 2 beep will be heard and exit the mode. Note: The remote will revert to normal operation from the set mode when 10-seconds has elapsed without a button entry.
-10-
Command Page
When a command (arm/disarm, or auxiliary channel) from the remote control is sent and received, the system will send a command page back to confirm receipt.
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will be sent to the remote control. When the remote receives an Alarm Page, the LCD icons will display the alarm system status information and the remote control will generate beeps.
Display
Beeps
5 short
Vibrations
1 times
Trigger
1st stage-Sensor warning
Ignition triggering
Icon will on for 2sec. and give 1 beep sound to indicate the function has been turned ON.
- With in 5 minutes, the 2-way remote will than give 1 beep sound every one minute for 5 cycles to remind the user within range. - After 5 minutes , the Antenna icon will indicates under receiving status:
Full reception
Half reception
Weak signal
For friendly usage, the 2-way remote will provide 2 beeps/ 3cycles and flashing icon after 35 minutes if the user is out of the receiving rage. However, afterwards if the 2-way remote detect the signal again from the system, 1 beep sound will be provided and flashing icon will be ON to indicate the 2-way remote is within range. Note: If under Check-in range mode, if alarm triggered, this function will automatically turn off (disable).
-12-
STANDARD FEATURES:
- To ARM the system:
To arm your system within proper operation range, simply press button once (while system in disarmed or Acc off position) . The system will respond one siren chirp, one lights flash, doors lock, disable engine starter, LED will begin flashing quickly until all sensor inputs are active - LED will start blinking slowly (flash once per second) to indicate the system is in full armed.
Door opened
3 chirps
1 long + 3 short
Trunk opened
4 chirps
1 long + 4 short
Hood opened
5 chirps
1 long + 5 short
- Auto Reset:
If a violation occurs the system will respond by sounding the siren and flashing the lights for approximately 30sec. before the system resets itself and continues to protect your car. If violation still occurs the system, siren and lights will working for 8 cycles then the system reset itself and continues to protect other zones.
-13-
- Intrusion Alert:
Upon disarming the system, if the vehicle is attempted or intruded, siren and lights will Indicates 4 chirps and 5 flashes to identify which zone was triggered. LED mode indicates the following different triggering.
flash 2 times after a pause flash 3 times after a pause flash 4 times after a pause flash 5 times after a pause flash 6 times after a pause Flash 7times after a pause
Sensor 1st-stage triggered Sensor 2nd-stage triggered Door switch triggered Trunk switch triggered Hood switch triggered Ignition switch triggered
Note: Before the ignition turn on, you may realized again which zone been triggered by press button (status check) once, the LCD will display triggered zone again.
-14-
Note: Under Silent Arm mode, if Sensor, Door, Hood or trunk been triggered, the siren will not activated, but if Ignition been triggered will activated the siren.
-15-
- Panic mode:
If you are threatened in or near your vehicle, you can attract attention by press button for 2sec. system will triggering for 30sec. To stop Panic mode at any time, simply press any button once. Note: if Panic mode activate in disarmed position, the 2-way remote will respond melody sound and LCD indicates flashing icons as under:
Under Panic mode, the 2-way remote will respond melody sound and flashing icons .
+ 5 beeps sound
-Heavy impact will activate the 2nd stage sensor and trigger the alarm for 30sec. 2-way remote will respond melody and flashing icon as under.
+ Melody sound
NOTE: Adjustments are made via the rotary control above the shock sensor.
Note: - if remote sensor bypassed, it will be detected again by next arming. - if armed with silent mode, to operate sensor bypass will only indicate by lights flash. -16-
- Valet mode:
To enter valet mode: Disarm the system and turn Ignition switch to ON position then press button + for over 2 seconds, or press Valet/over-ride switch for over 5 seconds, until siren give 1 long with 1 short chirp and LED light ON to confirm the system is in valet mode.
Note: Under Valet mode, each time turn Acc off , the siren will give 2 chirps for notification.
When the system is in the valet mode it can not be armed. The door lock and unlock will function as keyless entry system. To exit valet mode: Turn Ignition switch to ON position , then press button + for over 2seconds, or press Valet/over-ride switch for 5 seconds. You will hear siren provide 1 long with 2 short chirps and LED light OFF to confirm exit this mode and in alarm mode. The 2-Way remote will respond 1 long and 2 short beeps.
Exit: To disarm this function by (1) simply press button once. LED off. Note: Under this mode, if ignition force been turn ON , siren will give 1long + 1 short chirps warning, 10seconds later will activate the alarm, the 2way remote will indicate Anti car-jack icon and warning sound. To disarm it with programmed "Valet SW or PIN code " feature. (Please see Emergency disarm.)
- 2 step disarm:
This system offers 2 step disarm. It's a feature that make it possible to silence and reset the system while it is triggering, without disarming the system. If the system is triggered and the siren has been sounding, pressing any button once on the remote transmitter will stop the trigger and return the unit to the armed state. Note: Under system triggering, if press any button of 2-way remote once , the remote will stop the beep sound and LCD display will indicate the intrusion icon for 2sec. Press any button again to stop alarm triggering.
-18-
Note: If trunk has been remote opened in arming position, trunk switch will delay sensing for
5 seconds, and the shock sensor will be bypassed.
Exit mode : Pressing button once of the remote control within engine running mode , the system will delay 15 seconds and exit turbo mode, this delay time is allow the user using the key turn ignition on without stop the engine running. NOTE: 1. In engine running mode, the sensor zone trigger will be bypassed. 2. In engine running mode, if door, hood or trunk has been triggered, engine will stop running and alarming the system, simply press button to disarm . -19-
Turbo mode:
If programmed , the CH-5 channel will constant output when ignition turn on 1 minutes. It will keeps the engine running after arriving at your destination by ignition off for a programmed time 1/ 3/ 5/ 10 minutes. This allows the system's timer to conveniently cool down the turbo after you have left the vehicle.
2-way LCD display when armed: NOTE: you may disable this turbo mode after ignition turn off ,by press button once, the CH-5 will stop outputting.
Flashing icon
Note: in turbo mode time , if arming the system, sensors will be bypassed and LED flashing Green color for a programmed turbo time. Important: Turbo mode should be used only in open areas. Never start and run the vehicle in an enclosed space such as a garage or carport.
- Reverse warning : If programmed , connect to the (+)reverse back light. when you are
reversing your car the siren will give a short warning chirp every one second. Note: you can proceed the Reverse warning without siren chirps : (1) when you activated the Disarm w/o chirp before Ignition On. (2) when you reversing the Car simply press the button once. Head warning : If programmed , connect to the (+)head light . This feature will provide pre-warning chirps if you forgot to turn off the head light while leaving the car. Extra sensor (knock sensor) : If programmed , connect to the (+) optional extra sensor ( knock sensor). This feature will paging the 2way remote while trigger the sensor.
+ Melody sound
-20-
AHJ
AHJ
Flashing
+ melody sound
0sec.
20sec.
40sec.
60sec.
100sec.
Call switch
CALL
1. Enter Valet mode, the LED on status. 2. Turning ignition switch ON to OFF for 8 times within 10sec. , and steady in OFF position, siren will provide 1 long chirp. (Each time ignition switch turned off, siren will give 2 chirps for indication) 3. Now you have insert your former (old)PIN code to release this programming mode. For example your old PIN code is "2.5", turn ignition ON , LED start flashing (the times of LED flashing is according to the 1st PIN code), While LED flashing 2 times then turn ignition OFF, thus the 1st PIN code entered. Turn ignition ON again, LED start flashing, while it flashing 5 times then turn ignition OFF, thus the 2nd PIN code entered. If the 2-digits PIN code entered correctly, the siren will provide 2 long chirp and LED off . System now is in the new PIN code programming mode. Note: If enter not correct PIN code, siren will give 2 short chirps and exit this mode and back to Valet mode. Please repeat procedure step # 4 again. 4. Follow from 2-long chirp, the system under new PIN code setting mode. Suppose to set new PIN code : ( 3 . 8)., Turn ignition to ON , at time the LED will start flashing (the times of LED flashing is according to the 1st PIN code), While LED flashing 3 times then turn ignition OFF, thus the 1st PIN code been programmed. Turn ignition to ON again, LED start flashing, while it flashing 8 times then turn ignition OFF, thus the 2nd PIN code been programmed. 5. At the time system of Led will indicating to identify the New Pin code.3.8 (3 flash Pulse then 8 flash). Siren will give 2 short chirps to identify the new PIN has been programmed. 6. Then system existed new pin code setting and return back to the Valet mode.
-23-
Transmitter programming:
This programming features is provide the owner to learn the new transmitter into the system memory. This system can expand 4 different transmitters, and comes from factory with two transmitters already programmed into the system memory (1-way & 2-way ) . Whenever you want to add or delete transmitter code , the procedures are as following:
1. Enter Valet mode, the LED on status. 2. Turning ignition switch from ON to OFF and within 10 seconds, press Valet switch on-off
for 5 times, siren will provide 3 long chirp.
3. Now you have insert your former (old)PIN code to release this programming mode.
For example your old PIN code is "2.5", turn ignition ON , LED start flashing (the times of LED flashing is according to the 1st PIN code), While LED flashing 2 times then turn ignition OFF, thus the 1st PIN code entered. Turn ignition ON again, LED start flashing, while it flashing 5 times then turn ignition OFF, thus the 2nd PIN code entered. If the 2-digits PIN code entered correctly, the siren will provide 1 long chirp and the LED will flashing fast to indicate that the system is in Learning mode. Note: If enter not correct PIN code, siren will give 2 short chirps and exit this mode and back to Valet mode. Please repeat procedure step # 4 again. 4. Follow from 1-long chirp, LED flashing fast, It's available to learn the new transmitter into the
system by press any button once of the new transmitter, siren will give 1-long and 1-short chirps to indicate the first transmitter code learn into the system memory. To learn the 2nd,3rd,4th new transmitters, simply press any button once on the each transmitter, the numbers of siren short chirps is according to the numbers of the new transmitters learn into the system memory . (Each time learning new code of remote, the old code will be erased, hence you have to learn again.)
5. To exit this programming mode, if there is no new transmitters button been pressed, turn ignition
to ON or within 20 seconds without any button pressed , siren will give 2 short chirps and back to the Valet mode.
-24-
I
Press Item NO: LED flash
1-chirp
2-chirp
3-chirp
4-chirp
*W/I
W/O
*W/I
W/O
Automatic re-arm
W/I
*W/O
*Siren
Horn
*ON
OFF
W/I
With door lock
W/I
Without door lock
*W/O
Passive immobilizer
W/I
*W/O
W/I
*W/O
W/I
*W/O
10
*Remote latched
11
*0.8sec.
4sec.
2pulse unlock
12
*3sec.
45sec.
-25-
FEATURES
Press
once Press
twice Press
3 times Press
4 times
1-chirp
2-chirp
3-chirp
4-chirp
13
*W/I
W/O
14
Dome light
15
*1 minute
3 minute
5 minute
10 minute
16
PIN code
17
*W/I
W/O
18
W/I
*W/O
19
*Reverse warning
20
CH-6
21
CH-7
Press button once , siren will give 1 chirp and also in counting time , after your desire time if press button : Press button + output 1~120sec. If press button once, siren will give 1 chirp for programme time when arming/disarming , then siren will give 1 long chirp to indicate jump to next item. Disarming output 1~120sec.. If press button once, siren will give 1 chirp Press button + output 1~120sec. for programme time by press buttons to activate, then siren will give 1 long chirp to indicate jump to next item.
Arming output 1~120sec..
22
Factory default
Press button
W/O : means without the feature W/I : means with the feature Note: means factory default setting before delivery.
-26-
System Installation:
1. Thoroughly read and become familiar with the installation instructions before beginning the installation. 2. Review system contents: (1). A control module. (2).2-way pager transceiver antenna (3). One 5-button 2-way LCD remote transmitter. (4).One 3-button or 4-button random code remote transmitter (5).Dual stage shock sensor (6).High output 6-tone siren (optional ) (7).Status LED indicator (8).Valet over-ride switch (9).Harness: . 20-Pin main harness . Two 4-pin shock sensor harness . 6-pin transceiver harness . 2-Pin dual color LED harness (optional) . Valet/over-ride switch harness . 6-PIN Central door lock harness 3. Verify with the owner, the mounting location for all visible components, including the LED and Valet/over-ride switch. 4. Verify with the owner, the optional programme features. 5. Inspect and perform a function test for all vehicle systems before and after the installation. 6. Always use a Volt / Ohm meter for testing vehicle circuits. Never use a test light. 7. Always look before drilling any holes or mounting self-tapping screws. Be sure fuel lines and exterior wiring looms are clear as they often close to the chassis and difficult to see. 8. Protect all wires running from the engine compartment to the interior of the vehicle by covering with electrical tape and split loom tubing. Be sure to use a grommet when routing wires through the firewall. 9. Properly fuse any additional accessories such as window module, trunk opener, etc., making sure to power them separate from the alarm module. This will ensure the functionality system in the event of an accessory failure.
WIRING DIAGRAM
Dual color LED
M ALAR 2 W AY O L U N I T R CONT
R.F Antenna
Antenna
Extend the whole wire, align it with the intersection of dashboard and the front window glass. Keep it away from the metal at least 5 centimeter to have the best receiving condition.
Call switch
Optional blue LED indicator
Green Green/black Green/red Blue Blue/black Blue/red Lock Com Lock N/C Lock N/O Unlock Com Unlock N/C Unlock NO
+12V DC output - Ground 1st stage(-) trigger 2nd stage (-) trugger
-28-
Black(-)
10
11
12
13
14
15
16
17
18
19
20
(-) Green
(+) Yellow
Immobilizer-2
(-) Orange/black
(+) Purple
(-) Trunk output
(-) Gray
- Reverse warning - Head light warning - Extra sensor input (knock sensor)
Optional relay
CH-3 (-) negative pulsed output for Window close (confort) CH-4 (PROG) (-) pulsed output : - 2nd stage unlock - Remote latched CH-5 (PROG)
(-) Yellow/black Connect to (-) Trunk Pin Switch (-) Blue (-)Gray/black Connect to Re from Siren (+)Brown
(+) Siren
(-) pulsed output for : -Dome light -Keep engine run -Turbo mode CH-6 (PROG)
(-) Pink
(-) Brown/black
10Amp Fuse (+) /(-) White/red Lights(+)or (-) input , for parking lights power sources
CH-7 (PROG)
6A2 diode
-29-
+ 12V
LOCK MOTOR
2 WIRE ACTUATOR
UNLOCK MOTOR
(-)GND
3.) A built-in Central door lock with electric lock switch( like: CHRYSLER.. )
Central door lock wiring
Green/black Green Green/red Blue/black Blue Blue/red
+ 12V
MOTOR LOCK INSIDE THE FRONT DOOR
DOWN
ELECTRIC MOTOR
UP
4.) For vacuum type central door lock system ( like : Mercedes Benz , AUDI.. )
Central door lock wiring
Green/black Green Green/red Blue/black Blue Blue/red
+ 12V
ELECTRIC MOTOR
DOWN UP
AIR COMPRESSOR
-30-