Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SLVT
SLVE
1.-CHARACTERISTICS Metallic anchor, with functioning principle by expansion and installation by controlled torque. Male thread Use in non-craked concrete Easy assembly Use for heavy duty loads (static or quasy-static) Versions: zinc yellow pasitavated bolt and stud. Through fastening installation. Zinc yellow passivated bolt version apporved by the Instituto Eduardo Torroja de Ciencias de la Construccin (EOTA member) with European Technical Approval ETA 04/0100 option 8, from European Organization of Technical Approvals guide ETAG-001
2.- MATERIALS
ZINC YELLOW PASSIVATED BOLT ITEM COMPONENT Class 8.8 UNE EN ISO 898-1, zinc yellow pasivated 5m ISO 4042 A2L Zinc yellow pasivated 5m ISO 4042 A2L Tube EN 10305-2 -E235+C (1.0308) zinc yellow pasivated 5m ISO 4042 A2L ZINC YELLOW PASSIVATED STUD
1 2 3 4 5 6 7
BOLT DIN 931 WASHER DIN 9021 SLEEVE ANTIGIRUS EXPANSION SLEEVE CONE STUD
----Zinc yellow pasivated 5m ISO 4042 A2L Tube EN 10305-2 - E235+C (1.0308) zinc yellow pasivated 5m ISO 4042 A2L
Poliamide 6.6 Tube EN 10305-2 -E235+C (1.0308) zinc yellow pasivated 5m ISO 4042 A2L EN 10277-3 - 1.0718 zinc yellow pasivated 5m ISO 4042 A2L -----Tube EN 10305-2 - E235+C (1.0308) zinc yellow pasivated 5m ISO 4042 A2L EN10277-3 - 1.0718 zinc yellow pasivated 5m ISO 4042 A2L EN 10277-5 - 1.1191+C zinc yellow pasivated 5m ISO 4042 A2L
3.- DIMENSIONS
M20 x190 M10x110 M10x130 M12x130 M12x160 M16x150 M16x180 M20x160 M20x220 M24x210 210 111 24 70 26 72 32 5 36 SLVT20220 SLVT24210 SLVE24210 SLVT24240 SLVE24240 M24x240 240 141 M8x100 M8 100 58.5 8 30.5 11 24 120 78.5 M8x120
SIZE
dp: bolt diameter l: bolt length l3: sleeve length l4: antivirus length
[mm] [mm] [mm] [mm]
M24
l5: expans. sleeve length [mm] l6: cone length d2: washer diameter d3: sleeve diameter d4: antivirus diameter
[mm] [mm] [mm] [mm]
d5: expans. sleeve diam. [mm] d6: cone diameter s2: washer thickness sw : nut key Zinc yellow passivated bolt codes
[mm] mm] [mm]
12
15
18
24
28
3 19 SLVT12160 SLVT16150
4 30 SLVT20190 SLVE20190
SLVE08100
SLVE08120
SLVE10110
SLVE10130
SLVE12130
SLVE12160
SLVE16150
SLVE16180
SLVE20220
FT SLV ingles 04.02.09 6 4 de 7 SLVT, SLVI, SLVE M20x220 M24x210 32 195 175 155 310 60 30 35 250 465 233 SLVT20220 SLVT24210 SLVE24210 SLVT24240 SLVE24240 60 M24x240
M8x100 [mm] [mm] [mm] [mm] [mm] [mm] [mm] [Nm] [mm] [mm] 12 90 78 70
SIZE
d0: drill diameter h1: drill depth hnom: embedment depth hef: effective depth hc: base material thick. tfix: fixture thickness dw: fixture diameter Tins: installation torque scr,N: critical spacing dist. ccr,N: critical edge distance
M8x120
24 140 122 106 212 25 26 120 318 159 SLVT16150 SLVT16180 SLVT20160 SLVE20160 55 2
SLVE10110
SLVE10130
SLVE12130
SLVE12160
SLVE16150
SLVE16180
Before placing the anchor, checks to be made to ensure the strength class of the concrete is not lower than that to which the characteristic loads apply The concrete to be well compacted, e.g. without significant voids Base material temperatures during installation: -5 / + 40 C (80 C in a short period of time) Anchors to be installed ensuring not less than the specified embedment depth, The edge distance and spacing to be kept to the specified values, no minus tolerances to be allowed
SLVE20220
Drill to the minimum depth and diameter specified, maintaining perpendicular to the surface of the base material. Fixture holes themselves can be used as template. When drilling holes, care to be taken not to damage reinforcement in close proximity to the hole position. Action to be taken in the event that drilling is aborted, e.g. due to encountering reinforcement. It is recommended to install the anchors immediately beside the aborted drill hole, provide that anchoring depth is increased by the depth of the aborted drill hole, or make a new drilling at a minimum distance away of two times the depth of the aborted hole. Alternatively, a smaller distance may be chosen, provided the aborted drill hole is filled with high strength mortar. However, unless the aborted drill hole is filled with mortar, it is not permissible under a shear or oblique tension load for it to be closer than installation depth hnom in the direction of load application. Thoroughly clean hole from dust and drilling fragments. For holes to be subjected to temperatures below 0 C, measures to be taken to avoid the ingress of water into the hole and subsequent risk of local cracking of the concrete due to ice expansion. To introduce the anchor into the hole up to the embedment depth through the fixture. The installation minimum depth must be such that the sleeve notch is not visible out of the base material once installed. A hammer can be use to assure this depth. Do not apply any intermediate lay between the fixture and the washer (sealant, etc.). Apply the specified torque with a torque wrench. In case of holes with diameters higher than specified use washers of bigger diameter and thickness, but in this case it is not assured a correct distribution of shear loads amongst all the anchors of a same group. The shear load will be applied on those anchors with the correct fixture diameter. Due to the heavy loads transmitted by this anchor, when design of the structure it may be considered all the applied loads, including those transmitted by the anchor itself.
6.- CHARACTERISTIC RESISTANCES 6.1.- Characteristic resistances* in non-cracked C20/25** for an isolated anchor (without spacing and edge distance effects) are as per this table: METRIC
Zinc yellow passivated bolt
M8
SLVT08100 SLVT08120
M10
SLVT10110 SLVT10130
M12
SLVT12130 SLVT12160
M16
SLVT16150 SLVT16180
M20
SLVT20160 SLVT20190 SLVT20220
M24
SLVT24210 SLVT24240
[KN] [KN]
29.3 21.9
SLVE08100 SLVE08120
33.7 48.7
SLVE08100 SLVE08120
42.3 84.6
SLVE10110 SLVE10130
55.0 93.6
SLVE12130 SLVE12160
83.9 112.1
SLVE16150 SLVE16180
97.3 129.3
SLVE20160 SLVE20190 SLVE20220
[KN] [KN]
29.5 21.9
33.7 48.7
42.3 84.6
55.0 93.6
83.9 105.1
97.3 121.2
1KN 100 Kg * The characteristic resistance of an anchor is that with a 95% probability to be achieved in a tension test. It depends on the mean ultimate resistance, the number of tests and the scatter of the results. ** Concrete C20/25 per ENV206: characteristic resistance for a specimen 28 days old: Cylindrical sample 150 mm. x 300 height 200 N/mm2 Cubic sample 150 mm. side 250 N/mm2
Underline and cursive values correspond to steel failure. Characteristic resistance for tension and shear must be considered separately. 6.2.- Recommended safety factors SAFETY COEFFICIENTS
Zinc yellow passivated bolt Tension Shear Zinc yellow passivated stud Tension Shear REDUCTION COEFFICIENT FOR RESISTANCES CONCRETE STEEL FAILURE FAILURE 1.5 1.5 1.5 1.5 1.5 1.25 -1.5 1.4 INCREASING COEFFICIENT FOR LOADS
6.3.- Calculation example Fixing a load tension of 4.000 kg 4.000 kg 40 KN Increasing coefficient for loads: Using two SLVT M12 anchors Pull load characteristic resistance for SLVT M12 anchor: Concrete failure Concrete reduction for resistances coefficient: Checking: increased load must be lower than reduced resistance 40 KN x 1.4 2 x 42.3 KN / 1.5 Wedges distance must be longer than 267 mm and distance to any edge must be longer than 134 mm as well. 7.- OFFICIAL DOCUMENTATION The official European Technical Approval document ETA 04/0100 for zinc yellow pasivated bolt version is available through our export department. 1.4 42.3 KN 1.5