Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Ultrasonics
USM Go
Setting new standards in inspection instrumentation
The USM Go is the lightest and most portable ultrasonic flaw detector available from GE Sensing & Inspection Technologies. The USM Go is designed for ease of prolonged operation in the harshest inspection environments in the oil and gas, aerospace, power generation and automotive industries.
USM Go - Integrating years of GE experience and expertise in ultrasonics in a portable flaw detector.
All controls within fingertip reach. User can dedicate four function keys according to preference. A Flip function allows the instrument to be used equally well by left-handed and right-handed people. A detachable stand allows the user to optimize the viewing angle, when the instrument is desk- or bench-mounted. The attachment point is suitable for a standard tripod thread.
Increasing Productivity
The USM Go features intuitive operation so there is virtually no time-consuming, learning curve. You are productive from the moment you pick it up! Navigation is simplified using the proven graphical user interface (GUI) and the innovative joystick, allowing one-handed operation and fast and accurate adjustment. Other features allowing increased productivity are: A robust moulded rubber casing to withstand the harshest environments and significantly reduce downtime. The instrument is dust- and water-proof to IP67 and is tested to withstand shock and vibration. A standard USB connection to allow data to be downloaded from the flaw detector for further analysis or storage. The instrument is standard delivered with a 2 GB SD memory card (multiple cards can be used). Reports are produced in jpeg or bmp format so there is no need for special reading software. A simple on-board data logger to collect and save thickness measurements. State-of-the-art electronics, including digital amplifier, square wave pulser (optional) and digital filters for a wide range of application benefits.
A wide Pulse Repetition Frequency range. This allows the USM Go to be used at low PRF to inspect forged parts for inclusions and porosity without any ghost echoes and just as easily find application in weld inspection at high PRF when fast and regular scanning movement is required to optimize inspection times.
Weld Inspection Inspection of Forgings and Castings Inspection of Rails Inspection of Composites
USM Go Base The instrument 1 Battery Battery charger Power Cable Transportation case Brief Instruction Card Operating Manual on CD Manufacturer Certificate Hand strap AWS option DAC / TCG Option DGS Option Phantom PRF Option Square Wave Pulser Option
USM Go AWS
USM Go Advanced
Environmental
Battery 5.5 hours On board charging Off board charging with optional adaptor Proportional battery gauge indicating remaining operation time Universal AC (100-240 V, 50-60 Hz) Meets CCC, CE, UL, CSA and PSE requirements 175 mm x 111 mm x 50 mm 845 g (1.87 lb) with the battery Russian, Portuguese, Italian, Polish, Czech, English, German, French, Spanish, Chinese and Japanese
Connectors
Probe Connectors UT Output Connector USB Interface SD-Card Connector Two LEMO-00 SAP output, Alarm micro USB connector Full size SD card slot to accommodate standard SD cards
Pulser -
All pulser measurements taken according to EN12668 specifications Pulser Mode Simulated spike standard, Uni-polar square wave optional Pulser Voltage 120 V to 300 V with 10 V step in a tolerance of 10% (SQ Mode) Pulser Width 30 ns to 500 ns with 20 ns step in a tolerance of 10% (SQ Mode) Pulser Amplitude Low: 120 V, High: 300 V (Spike Mode) Damping 50 or 1000 Ohms PRF Automatically optimized between 15 Hz to 2000 Hz, 3 automatic adjustment modes: AutoLow, Auto Med, AutoHigh - Optional manual control of PRF from 15 to 2000 Hz.
Receiver
Range Digital Gain Analog Bandwidth Filters 14016 mm at steel longitudinal wave (557) Dynamic range of 110 dB, with 0.2 dB step 0.2 MHz - 20 MHz Broad Band 0.6 - 16 1 MHz 0.5 - 2.3 2 MHz (also 2.25) 0.6 - 3.8 5 MHz (also 4) 2.3 - 7.9 10 MHz 6.2 - 13.4 13 MHz 10.8 - 17.3
Gate
Independent Gates Rectification Measurement 2 gates (A and B), Gate B supports triggering by gate A Positive (POS) Full wave (FW) Negative (NEG) RF Peak Flank
Options
USM Go AWS Option USM Go Dac Option AWS sizing tool according to AWS D1.1 Structural welding code Dac sizing tool EN 1712- EN 1713 EN 1714 16 points ASME & ASME III Compliant with JIS Z3060 compliant TCG: 120 dB dynamic TCG: 110 dB/s slope DGS sizing tool compliant with EN 1712 Custom linear and grid file creation
Memory
Capacity Report 2 GB SD Card) Jpeg reports
USM Go DGS Option USM Go Embedded Datalogger Option USM Go Squarewave Allows pulser parameters fine tuning Pulser Option Voltage adjustment from 120 V to 300V per 10 V steps Pulse width adjustment from 30 ns to 500 ns per 10ns steps USM Go Manual PRF Allows Manual PRF optimization between 15 Hz and and Phantom Option 2000 Hz per step of 5 Hz. Phantom PRF will help to identify ghost echo due to multiple reflections in low materials
www.geit.com
GEIT-20056EN(08/09) 2009 General Electric Company. All Rights Reserved. Specifications are subject to change without notice. GE is a registered trademark of General Electric Company. Other company or product names mentioned in this document may be trademarks or registered trademarks of their respective companies, which are not affiliated with GE. CRxFlex is a trademark of GE Sensing & Inspection Technologies