Sei sulla pagina 1di 58

P.

A COLLEGE OF ENGINEERING AND TECHNOLOGY POLLACHI, COIMBATORE - 6420 002

RECORD NOTE BOOK

VI - SEMESTER, BE - MECHANICAL ENGINEERING


SIMULATION AND ANALYSIS LABORATORY

DEPARTMENT OF MECHANICAL ENGINEERING


P.A. COLLEGE OF ENGINEERING AND TECHNOLOGY, POLLACHI - 6420 002

(Affiliated to Anna University - Coimbatore)

P.A COLLEGE OF ENGINEERING AND TECHNOLOGY POLLACHI, COIMBATORE - 642 002.


BONAFIDE CERTIFICATE

Registration No.

Certified

that

this

is

the

bonafide

record of

of

work -

done

by B.E.

Mr...

semester

Mechanical Engineering Branch / Batch during the academic year . in the Simulation And Analysis laboratory.

Head of the Department

Staff In-Charge

Submitted for the University practical examination held on at P.A College of Engineering and Technology, Pollachi.

Internal Examiner Date:

External Examiner Date:

LABARATORY CLASSES - INSTRUCTIONS TO STUDENTS


1. Students must attend the lab classes with ID cards and in the prescribed uniform. 2. Boys-shirts tucked in and wearing closed leather shoes. Girls students with cut shoes, overcoat, and plait incite the coat. Girls students should not wear loose garments. 3. Students must check if the components, instruments and machinery are in working condition before setting up the experiment. 4. Power supply to the experimental set up/ equipment/ machine must be switched on only after the faculty checks and gives approval for doing the experiment. Students must start to the experiment. Students must start doing the experiments only after getting permissions from the faculty. 5. Any damage to any of the equipment/instrument/machine caused due to carelessness, the cost will be fully recovered from the individual (or) group of students. 6. Students may contact the lab in charge immediately for any unexpected incidents and emergency. 7. The apparatus used for the experiments must be cleaned and returned to the technicians, safely without any damage. 8. Make sure, while leaving the lab after the stipulated time, that all the power connections are switched off. 9. EVALUATIONS: All students should go through the lab manual for the experiment to be carried out for that day and come fully prepared to complete the experiment within the prescribed periods. Student should complete the lab record work within the prescribed periods. Students must be fully aware of the core competencies to be gained by doing experiment/exercise/programs. Students should complete the lab record work within the prescribed periods. The following aspects will be assessed during every exercise, in every lab class and marks will be awarded accordingly: Preparedness, conducting experiment, observation, calculation, results, record presentation, basic understanding and answering for viva questions. In case of repetition/redo, 25% of marks to be reduced for the respective component.

NOTE 1 Preparation means coming to the lab classes with neatly drawn circuit diagram /experimental setup /written programs /flowchart, tabular columns, formula, model graphs etc in the observation notebook and must know the step by step procedure to conduct the experiment. Conducting experiment means making connection, preparing the experimental setup without any mistakes at the time of reporting to the faculty. Observation means taking correct readings in the proper order and tabulating the readings in the tabular columns.

Calculation means calculating the required parameters using the approximate formula and readings. Result means correct value of the required parameters and getting the correct shape of the characteristics at the time of reporting of the faculty. Viva voice means answering all the questions given in the manual pertaining to the experiments. Full marks will be awarded if the students performs well in each case of the above component NOTE 2 Incompletion or repeat of experiments means not getting the correct value of the required parameters and not getting the correct shape of the characteristics of the first attempt. In such cases, it will be marked as IC in the red ink in the status column of the mark allocation table given at the end of every experiment. The students are expected to repeat the incomplete the experiment before coming to the next lab. Otherwise the marks for IC component will be reduced to zero. NOTE 3 Absenteeism due to genuine reasons will be considered for doing the missed experiments. In case of power failure, extra classes will be arranged for doing those experiments only and assessment of all other components preparedness; viva voice etc. will be completed in the regular class itself. NOTE 4 The end semester practical internal assessment marks will be based on the average of all the experiments.

INDEX

Ex. No

Date

Name of the Experiment

Mark

Page No

Staff Signature

10

Completed date:

Average Mark:

Staff - in - charge

INDEX

Ex. No

Date

Name of the Experiment

Mark

Page No

Staff Signature

11

12

13

14

15

16

17

18

19

20

Completed date:

Average Mark:

Staff - in - charge

INTRODUCTION TO ANSYS
ANSYS HISTORY A general purpose Finite Element Analysis (FEA) package Founded in 1970 Founder: Dr. John Swanson 1969: STASYS (Structural Analysis System) 1970: ANSYS 1975: PC version 2004: ANSYS 8.1 multi-physics 2010: ANSYS 12.1 2012: ANSYS 13.0

WHAT CAN ANSYS DO? Structural analysis - Stress / strain, deformation, etc. Thermal analysis Fluid flow (CFD) Electro magnetic Multi-physics (solid/fluid/electromagnetic..) HOW IT WORKS? Finite Element Method (FEM) Continuum media Curve Piece-wised element connected by the Nodes

Piece-wised Line

FEM PROCESS: 3 BASIC STEPS PREPROCESSING

Build FEM Model


SOLUTION Geometry Construction Mesh Generation (right element type)

Boundary and Load condition implementation Submit the model to ANSYS solver
POSTPROCESSING

Check and Evaluate the results


Third Party CAD Model ANSYS 3D Model

Geometry Construction

PREPROCESSING

Mesh Generation

Boundary and Load implementation SOLUTION Job submission POSTPROCESSING

Evaluate the Results

MODELLING APPROACH Bottom-up approach of model by defining the geometry of the structure with nodes and elements Top-down approach

Creation

Building a solid model using a 3D CAD program and then dividing the model into
nodes and elements APDL (ANSYS Parametric Design Language) h - Method

It is used for regular surface Developed in 1970s The name is derived from the field of numerical analysis where the h is used for
step size, to achieve convergence in the analysis

The h-element is always of low order, usually linear or quadratic.


p Method

No restrictions to shape and size Developed in late 1980s This provides option of optimizing a structure. p elements can have edge polynomial as high as 9th order, unlike the low order
polynomials of h-elements UNIT SYSTEM IN ANSYS ANSYS had no build-in unit system The unit must be consistent The precision of results depends on the model type and mesh type ANSYS BENEFITS

Simulate how a design behaves under real-world conditions without having to build costly physical prototypes. Obtain accurate results on design behavior Increase your confidence in your final product design by virtually testing a design under all conceivable loading conditions. ANSYS APPLICATIONS

Strength, durability and vibration assessment of various structures such as aircrafts, cars, trucks, or a train Structural dynamic response simulation of loads that vary with time or frequency Modal based analysis of large systems such as in automotive and aerospace vehicle systems Simulation of interior acoustics for sound pressure inside a bounded domain Static and transient analysis of structures involving material and geometric nonlinear behavior and nonlinear boundary condition Advanced heat transfer analysis with contact including conduction, convection and radiation to understand the effect of temperature fluctuations in consumer electronic devices such as television

or cell phone.

Automated thermal followed by structural analysis Analysis of structures with rotating components Include the effects of aero elasticity on structures Combined topology, sizing and shape optimization of structures with manufacturing constraints.

STARTING ANSYS: The ANSYS graphical user interface can be started by selecting the ANSYS icon located in the ANSYS 12.1 Folder.
12.1

Selecting the ANSYS icon will take you directly to the graphical user interface. ANSYS Graphical User Interface: After starting ANSYS, two windows will appear. The first is the ANSYS 12.1 Output Window.

This window displays a listing of every command that ANSYS executes. If you encounter problems, this is a good place to look to see what ANSYS is doing or has done. This is one location where you will find all of the warnings and error messages that appear and the command that generated the warning/error.

The second window is the ANSYS Research FS graphical user interface. This is divided into 4 sections (shown on next page): 1. ANSYS Utility Menu 2. ANSYS Toolbar Menu 3. ANSYS Main Menu 4. Display window Each section will be discussed in further detail below. Current Job name

1 2

ANSYS Utility Menu Within this menu, you can perform file operations, list and plot items, and change display options.

File Drop-down Menu The File drop-down menu includes the options to clear the database, change, resume, and save the current model.

Clear and Start New deletes the current database. It does not clear the log or error files. Change Jobname changes the name of the database and associated files. The next time you save, it will write everything to the current jobname. It will not delete the previous jobname or associated files. Note: unless you check the box for New log and error files, it will continue to write to the current log and error files. Change Directory allows you to switch directories where the files are being saved.

Resume Jobname.db and Resume from allows you to open a model that has already been saved. Note: If you resume a file, ANSYS does not automatically switch the current jobname to the name of the file you resumed from. Change the jobname otherwise you may write over another model. Save as Jobname.db and Save as allow you to save the model. If you choose save as it will save the file as a different name. If you do not change the jobname, the next time you save it will overwrite the current jobname and not the save as file name.

List Pull-down Menu The list pull-down menu allows you to view the log and error files, obtain a listing of geometric entities, elements and their properties, nodes, and boundary conditions and loads applied to the model. This menu allows you to view the log and error files. The log file is a summary of every command performed in ANSYS while the error file may provide insight into troubleshooting problems with the model/analysis. These list the geometric entities and their components.

Selecting the Nodes and Elements listings are easy methods to determine the number of nodes and elements in the model.

Plot Pull-down Menu This pull-down menu allows you to plot the various components of the model such as keypoints, areas, volumes and elements.

Use the plot elements command to obtain the mesh plot.

PlotCtrls Pull-Down Menu This menu includes the controls to pan/zoom/rotate your model, select the numbering options, change styles and generate hard copies of the plots.

This pops up a window allowing you to pan, zoom and rotate the model.

The Numbering selection allows you to turn on/off the keypoint, lines, areas, volumes, nodes and element numbering.

The Hard Copy selection sends the plot to a printer or image file.

ANSYS Toolbar

If you get a message reporting that the percent error cannot be calculated with powergraphics turned on, click the POWRGRPH button to turn off powergraphics.

ANSYS Main Menu The ANSYS Main Menu contains all of the commands to create, mesh, apply loads, solve, and view results of the FE analysis. The Main Menu is divided into sections that sequentially follow the steps involved in an analysis. Preprocessor Select the element types to be used. Multiple types may be selected and applied to a model.

Input the material properties. Multiple materials may be entered and applied to a model.

Use the modeling options to create the model. Note: ANSYS uses a hierarchy for modeling: keypoints (lowest) lines areas volumes (highest) If you create a volume, all of the areas, lines and keypoints will be automatically created for you.

Use the meshing options to mesh the model.

To delete mistakes, choose the Delete menu under Modeling. It is important to select the right option. For example, if you select Areas Only, the area will be deleted but the lines and keypoints that make up that area will remain. If you select Areas and Below, it will delete the area plus the lines and keypoints that define the area. NOTE: there is not an undo button in ANSYS, once deleted, the component must be re-created.

Solution Choose the type of analysis to perform.

Apply loads and boundary conditions to the model.

Solve the model.

Post Processing

Plot contour or vector plots of results.

Lists the percent error. If you get a message Cannot view percent error with powergraphics on, click the powergraphics button on the ANSYS Toolbar to turn it off.

List the results for every node. This can be used to get the maximum and minimum values of results.

Ex. No: 1 Date:

STRESS ANALYSIS OF A PLATE WITH A CIRCULAR HOLE

AIM: To conduct the stress analysis in a plate with a circular hole using ANSYS software.

SYSTEM CONFIGURATION: Ram Processor Operating system Software : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version10.0)

PROCEDURE: The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10.0- Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 1. Preference - Structural- h-Method - Ok. 2. Preprocessor - Element type - Add/Edit/Delete Add Solid, 8 node 82 Ok Option Choose Plane stress w/thk - Close. 3. Real constants - Add/Edit/Delete Add Ok THK 0.5 Ok - Close. 4. Material props - Material Models Structural Linear Elastic Isotropic - EX 2e5, PRXY 0.3 - Ok. 5. Modeling Create Areas Rectangle - by 2 corner - X=0, Y=0, Width=100, Height=50 - Ok. Circle - Solid circle - X=50, Y=25, Radius=10 - Ok. Operate Booleans Subtract Areas - Select the larger area (rectangle) Ok Ok - Select Circle Next Ok - Ok. 6. Meshing - Mesh Tool Area Set - Select the object Ok - Element edge length 2/3/4/5 Ok Mesh Tool - Select TRI or QUAD - Free/Mapped Mesh - Select the object - Ok. SOLUTION: 1. Solution Define Loads Apply Structural Displacement - On lines - Select the boundary where is going to be arrested Ok - All DOF - Ok. Pressure - On lines - Select the load applying area Ok - Load PRES valve = 1 N/mm2- Ok. 2. Solve Current LS Ok Solution is done Close. POST PROCESSING: 1. General post proc - Plot Result - Contour plot - Nodal Solution Stress - Von mises stress - Ok.

TO VIEW THE ANIMATION: 1. Plot control Animates - Mode Shape Stress Vonmises - Ok. 2. Plot control Animate - Save Animation - Select the proper location to save the file (E drive-user) Ok. FOR REPORT GENERATION: 1. File Report Generator Choose Append OK Image Capture Ok - Close.

RESULT:

Thus the stress analysis of rectangular plate with a circular hole is done by using the ANSYS Software.

STRESS ANALYSIS OF A PLATE WITH A CIRCULAR HOLE

1 N/mm2

100

Youngs Modulus Poissons Ratio

200 GPa = 0.3

Ex. No: 2 Date:

STRESS ANALYSIS OF RECTANGULAR L BRACKET

AIM: To conduct the stress analysis of a rectangular L section bracket using ANSYS software. SYSTEM CONFIGURATION: Ram Processor Operating system Software PROCEDURE: The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10- Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 1. Preference - Structural- h-Method - Ok. 2. Preprocessor - Element type - Add/Edit/Delete Add Solid, 8 node 82 Ok Option Choose Plane stress w/thk - Close. 3. Real constants - Add/Edit/Delete Add Ok THK 0.5 Ok - Close. 4. Material props - Material Models Structural Linear Elastic Isotropic - EX 2e5, PRXY 0.3 Ok. 5. Modeling Create Key points - In active CS enter the key point number and X, Y, Z location for 6 key points to form the rectangular L-bracket. Lines lines - Straight line - Connect all key points to form as lines. Areas Arbitrary - by lines - Select all lines - ok. Lines - Line fillet - Select the two lines where the fillet is going to be formed Ok enter the Fillet radius=10 - Ok. Areas Arbitrary - through KPs - Select the key points of the fillet - Ok. Operate Booleans Add Areas - Select the areas to be add (L Shape & fillet area) - ok. Create Areas Circle - Solid circle - Enter the co-ordinates, radius of the circles at the two ends (semicircles) -Ok. Operate Booleans Add Areas - Select the areas to be add (L Shape & two circles) - Ok. Create Areas Circle - Solid circle Enter the coordinates, radius of the two circles which are mentioned as holes - Ok. Operate Booleans Subtract Areas - Select the area of rectangle Ok - Select the two circles Ok. 6. Meshing - Mesh Tool Area Set - Select the object Ok - Element edge length 2/3/4/5 Ok Mesh Tool - Select TRI or QUAD - Free/Mapped Mesh - Select the object - Ok. SOLUTION: 3. Solution Define Loads Apply Structural Displacement - On lines - Select the boundary where is going to be arrested Ok - All DOF - Ok. : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version10)

Pressure - On lines - Select the load applying area Ok - Load PRES valve = -10000 N (- Sign indicates the direction of the force i.e. downwards) - Ok. 4. Solve Current LS Ok Solution is done Close. POST PROCESSING: 2. General post proc - Plot Result - Contour plot - Nodal Solution Stress - Von mises stress - Ok. TO VIEW THE ANIMATION: 3. Plot control Animates - Mode Shape Stress - Von mises - Ok. 4. Plot control Animate - Save Animation - Select the proper location to save the file (E drive-user) Ok. FOR REPORT GENERATION: 2. File Report Generator Choose Append OK Image Capture Ok - Close.

RESULT: Thus the stress analysis of rectangular L section bracket is done by using the ANSYS Software.

STRESS ANALYSIS OF RECTANGULAR L BRACKET

5 - 50 kN

Youngs Modulus Poissons Ratio

200 GPa = 0.3

Ex. No: 3 Date:

STRESS ANALYSIS OF BEAM

AIM: To conduct the stress analysis in a beam using ANSYS software.

SYSTEM CONFIGURATION: Ram Processor Operating system Software : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version10)

PROCEDURE: The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10 - Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 7. Preference - Structural- h-Method - Ok. 8. Preprocessor - Element type - Add/Edit/Delete Add Beam, 2D elastic 3 Ok Options Ok Close. 9. Sections beam Common sections Select the correct section of the beam and input the values of B and H Preview Note down the values of area, Iyy. 10. Real constants - Add/Edit/Delete Add Ok Enter the values of area=6, Izz=4.5, height=3 Ok Close. 11. Material props - Material Models Structural Linear Elastic Isotropic - EX 200e9, PRXY 0.3 Ok. 12. Modeling Create Key points In active CS Enter the values of CS of each key points Apply Ok. Lines Lines Straight line Pick the all points Ok. 13. Meshing Mesh attributes All lines Ok. Meshing Size cntrls Manual size Lines All lines Enter the value of element edge length [or] Number of element divisions Ok. Mesh tool Mesh Pick all. SOLUTION: 5. Solution Define Loads Apply Structural Displacement - On key points Select the 1st key point UX, UY Ok. On key points select the 2nd key point UY Ok and 3rd key point UY Ok.

Pressure - On beam Box Select the area on the beam Ok Enter VAL I 200000, VAL J 200000 Ok. This method is followed for the remaining areas and loads. Force/Moment On key points Select the key point Ok direction of force/moment FY, value = -50,000 (- sign indicates the direction of the force) Ok. 6. Solve Current LS Ok Solution is done Close. POST PROCESSING: 3. General post proc Element table Define table Add By sequence num SMISC,6 Ok SMISC,12 Ok LS,2 Ok LS,3 - Ok Close. Plot results Contour plot Nodal solution DOF solution Y component of displacement Ok. Contour plot Line element Res Node I SMIS 6, Node J SMIS 12 Ok. Contour plot Line element Res Node I LS 2, Node J LS 3 Ok FOR REPORT GENERATION: 3. File Report Generator Choose Append OK Image Capture Ok - Close.

RESULT:

Thus the stress analysis of beam is done by using the ANSYS Software.

STRESS ANALYSIS OF BEAM

Youngs Modulus Poissons Ratio

200 GPa = 2m 3m 0.3

Breadth of the beam, b = Depth of the beam, d =

Ex. No: 4 Date:

CONVECTIVE HEAT TRANSFER ANALYSIS OF A 2D COMPONENT

AIM: To conduct the convective heat transfer analysis of a 2D component using ANSYS software. SYSTEM CONFIGURATION: Ram Processor Operating system Software PROCEDURE: The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10- Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 14. Preference Thermal - h-Method - Ok. 15. Preprocessor - Element type - Add/Edit/Delete Add Solid, Quad 4 node 55 Ok Close. 16. Real constants - Add/Edit/Delete Add Ok. 17. Material props - Material Models Thermal Conductivity Isotropic KXX 16 Ok. 18. Modeling Create Key points - In active CS enter the key point number and X, Y, Z location for 8 key points to form the shape as mentioned in the drawing. Lines lines - Straight line - Connect all the key points to form as lines. Areas Arbitrary - by lines - Select all lines - ok. [we can create full object (or) semi-object if it is a symmetrical shape] 19. Meshing Mesh tool Areas, set select the object Ok Element edge length 0.05 - Ok Mesh tool- Tri, free mesh Select the object Ok. SOLUTION: 7. Solution Define Loads Apply Thermal Temperature - On lines Select the lines Ok Temp. value 300 Ok Convection On lines select the appropriate line Ok Enter the values of film coefficient 50, bulk temperature 40 Ok. 8. Solve Current LS Ok solution is done Close. POST PROCESSING: 4. General post proc List results Nodal Solution DOF Solution Nodal temperature Ok 5. Plot results Contour plot Nodal solution DOF solution Nodal Temperature Ok. : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version10)

FOR REPORT GENERATION: 4. File Report Generator Choose Append OK Image Capture Ok - Close.

RESULT: Thus the convective heat transfer analysis of a 2D component is done by using the ANSYS Software.

CONVECTIVE HEAT TRANSFER ANALYSIS OF A 2D COMPONENT

Thermal Conductivity of the material =

16 W/m.C

Ex. No: 5 Date:

CONDUCTIVE HEAT TRANSFER ANALYSIS OF A 2D COMPONENT

AIM: To conduct the conductive heat transfer analysis of a 2D component using ANSYS software.

SYSTEM CONFIGURATION: Ram Processor Operating system Software : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version10)

PROCEDURE: The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10 - Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 20. Preference Thermal - h-Method - Ok. 21. Preprocessor - Element type - Add/Edit/Delete Add Solid, Quad 4 node 55 Ok Close Options plane thickness Ok. 22. Real constants - Add/Edit/Delete Add Ok THK 0.5 Ok Close. 23. Material props - Material Models Thermal Conductivity Isotropic KXX 10 Ok. 24. Modeling Create Areas - Rectangle by 2 corners Enter the coordinate values, height, width - Ok. 25. Meshing Mesh tool Areas, set select the object Ok Element edge length 0.05 - Ok Mesh tool- Tri, free - mesh Select the object Ok. SOLUTION: 9. Solution Define Loads Apply Thermal Temperature - On lines Select the right and left side of the object Ok Temp. Value 100 On lines select the top and bottom of the object Ok Temp 500 Ok. 10. Solve Current LS Ok Solution is done Close. POST PROCESSING: 6. General post proc Plot results Contour plot Nodal solution DOF solution Nodal Temperature Ok.

FOR REPORT GENERATION: 5. File Report Generator Choose Append OK Image Capture Ok - Close.

RESULT:

Thus the conductive heat transfer analysis of a 2D component is done by using the ANSYS Software.

CONDUCTIVE HEAT TRANSFER ANALYSIS OF A 2D COMPONENT

500C

100C

100C

500C

Thermal Conductivity of the material = Dimension of the object

10 W/m.C = 2mx2m

Ex. No: 6 Date:

THERMAL STRESS ANALYSIS OF A 2D COMPONENT

AIM: To conduct the thermal stress analysis of a 2D component by using ANSYS software.

SYSTEM CONFIGURATION: Ram Processor Operating system Software : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version10)

PROCEDURE: The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10 - Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 26. Preference Structural - h-Method - Ok. 27. Preprocessor - Element type - Add/Edit/Delete Add Solid, Quad 4 node 42 Ok Options plane strs w/thk Ok Close. 28. Real constants - Add/Edit/Delete Add Ok THK 100 Ok Close. 29. Material props - Material Models Structural Linear Elastic - Isotropic EX 2e5, PRXY 0.3 Ok Thermal expansion Secant coefficient Isotropic ALPX 12e-6 Ok. 30. Modeling Create Areas - Rectangle by 2 corners Enter the coordinate values, height, width - Ok. 31. Meshing Mesh tool Areas, set select the object Ok Element edge length 10 - Ok Mesh tool- Tri, free - mesh Select the object Ok. SOLUTION: 11. Solution Define Loads Apply Structural Displacement - On lines Select the boundary on the object Ok Temperature Uniform Temp Enter the temp. Value 50 Ok. 12. Solve Current LS Ok Solution is done Close. POST PROCESSING: 7. General post proc Plot results Contour plot Nodal solution Stress 1st principal stress Ok Nodal solution DOF Solution Displacement vector sum - Ok.

FOR REPORT GENERATION: 6. File Report Generator Choose Append OK Image Capture Ok - Close.

RESULT:

Thus the thermal stress analysis of a 2D component is done by using the ANSYS Software.

THERMAL STRESS ANALYSIS OF A 2D COMPONENT

T = 50C

500

500

Youngs modulus Poissons Ratio Thermal expansion coefficient

200 GPa = 0.3

12 x 10-6

Ex. No: 7 Date:

MODE FREQUENCY ANALYSIS OF BEAM

AIM: To conduct the mode frequency analysis of beam using ANSYS software. SYSTEM CONFIGURATION: Ram Processor Operating system Software PROCEDURE: The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10- Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 32. Preprocessor - Element type - Add/Edit/Delete Add Beam, 2D elastic 3 Ok Close. 33. Real constants - Add/Edit/Delete Add Ok Area 0.1e-3, Izz 0.833e-9, Height 0.01 Ok Close. 34. Material props - Material Models Structural Linear Elastic - Isotropic EX 206e9, PRXY 0.25 Ok Density DENS 7830 Ok. 35. Modeling Create Key points Inactive CS Enter the coordinate values - Ok. Lines lines Straight Line Join the two key points Ok. 36. Meshing Size Cntrls manual size lines all lines Enter the value of no of element divisions 25 Ok. Mesh Lines Select the line Ok. SOLUTION: 13. Solution Define Loads Apply Structural Displacement - On nodes Select the node point Ok All DOF Ok. Analysis type New analysis Modal Ok. Analysis type Analysis options Block Lanczos enter the value no of modes to extract as 3 or 4 or 5 Ok End Frequency 10000 Ok. 14. Solve Current LS Ok Solution is done Close. POST PROCESSING: 8. General post proc Read results First set - Plot results Deformed shape Choose Def+undeformed Ok. Read results Next set - Plot results Deformed shape Choose Def+undeformed Ok and so on. : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version10)

FOR REPORT GENERATION: 7. File Report Generator Choose Append OK Image Capture Ok - Close. (Capture all images)

RESULT: Thus the mode frequency analysis of beam is done by using the ANSYS Software.

MODE FREQUENCY ANALYSIS OF BEAM

Youngs modulus Poissons Ratio Weight Density

206 GPa = = 0.25 7.83 x 103 kg/m3

Ex. No: 8 Date:

HARMONIC ANALYSIS OF A 2D COMPONENT

AIM: To conduct the harmonic analysis of a 2D component by using ANSYS software.

SYSTEM CONFIGURATION: Ram Processor Operating system Software : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version10)

PROCEDURE: The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10- Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 37. Preprocessor - Element type - Add/Edit/Delete Add Beam, 2D elastic 3 Ok Close. 38. Real constants - Add/Edit/Delete Add Ok Area 0.1e-3, Izz 0.833e-9, Height 0.01 Ok Close. 39. Material props - Material Models Structural Linear Elastic - Isotropic EX 206e9, PRXY 0.25 Ok Density DENS 7830 Ok. 40. Modeling Create Key points Inactive CS Enter the coordinate values - Ok. Lines lines Straight Line Join the two key points Ok. 41. Meshing Size Cntrls manual size lines all lines Enter the value of no of element divisions 25 Ok. Mesh Lines Select the line Ok. SOLUTION: 15. Solution - Analysis type New analysis Harmonic Ok. Analysis type Analysis options Full, Real+imaginary Ok Use the default settings Ok 16. Solution Define Loads Apply Structural Displacement - On nodes Select the node point Ok All DOF Ok. Force/Moment On Nodes select the node 2 Ok Direction of force/mom FY, Real part of force/mom -100 Ok. Load step Opts Time/Frequency Freq and Substps Enter the values of Harmonic freq range 1-100, Number of sub steps 100, Stepped Ok. 17. Solve Current LS Ok Solution is done Close.

POST PROCESSING: 9. TimeHist postpro Variable Viewer Click Add icon Nodal Solution DOF Solution YComponent of displacement Ok Enter 2 Ok. Click List data icon and view the amplitude list. Click Graph icon and view the graph. To get a better view of the response, view the log scale of UY. Plotctrls Style Graphs Modify axes Select Y axis scale as Logarithmic Ok. Plot Replot Now we can see the better view.

FOR REPORT GENERATION: 8. File Report Generator Choose Append OK Image Capture Ok - Close. (Capture all images)

RESULT:

Thus the harmonic analysis of a 2D component is done by using the ANSYS Software.

HARMONIC ANALYSIS OF A 2D COMPONENT

Youngs modulus Poissons Ratio Weight Density Length of the Beam

= = = =

206 GPa 0.25 7.83 x 103 kg/m3 1m

Ex.No: 9 Date:

STRESS ANALYSIS OF A PLATE WITH A CIRCULAR HOLE

AIM:
To determine the stress and displacement fields on the Hollow Pipe using ANSYS.

SYSTEM CONFIGURATION:
Ram Processor Operating system Software : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version12.0/12.1)

PROCEDURE:
The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10 - Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 42. Preference - Structural- h-Method - Ok. 43. Preprocessor - Element type - Add/Edit/Delete Add Solid, 8 node 82 Ok Option Choose Plane stress w/thk - Close. 44. Real constants - Add/Edit/Delete Add Ok THK 0.5 Ok - Close. 45. Material props - Material Models Structural Linear Elastic Isotropic - EX 2e5, PRXY 0.3 Ok. 46. Modeling Create Areas Solid annuals circle - X=0, Y=0, radi1=1000, radi 2-1200, Ok. 47. Meshing - Mesh Tool Area Set - Select the object Ok - Element edge length 2/3/4/5 Ok Mesh Tool - Select TRI or QUAD - Free/Mapped Mesh - Select the object - Ok. SOLUTION: Solution Define Loads Apply Structural Displacement - On lines - Select the boundary where is going to be arrested Ok - All DOF - Ok. Pressure - On lines - Select the load applying area Ok - Load PRES valve = 1 MPa- Ok. 19. Solve Current LS Ok Solution is done Close. 18. POST PROCESSING: 10. General post proc - Plot Result - Contour plot - Nodal Solution Stress - Von mises stress - Ok.

TO VIEW THE ANIMATION: 5. Plot control Animates - Mode Shape Stress - Von mises - Ok. 6. Plot control Animate - Save Animation - Select the proper location to save the file (E drive-user) Ok. FOR REPORT GENERATION: 9. File Report Generator Choose Append OK Image Capture Ok - Close.

RESULT:
Thus the stress analysis of rectangular plate with a circular hole is done by using the ANSYS Software.

STRESS ANALYSIS OF A PLATE WITH A CIRCULAR HOLE

All Dimensions are in mm

Youngs Modulus Poissons Ratio

= 200 GPa = 0.33

Ex.No: 10 Date:

STRESS ANALYSIS OF BEAM

AIM:
To conduct the stress analysis in a beam using ANSYS software.

SYSTEM CONFIGURATION:
Ram Processor Operating system Software : 2 GB : Core 2 Quad / Core 2 Duo : Window XP Service Pack 3 : Ansys (Version12.0/12.1)

PROCEDURE:
The three main steps to be involved are 1. Pre Processing 2. Solution 3. Post Processing Start - All Programs Ansys 10 - Mechanical APDL Product Launcher Set the Working Directory as E Drive, User - Job Name as Roll No., Ex. No. Click Run. PREPROCESSING: 48. Preference - Structural- h-Method - Ok. 49. Preprocessor - Element type - Add/Edit/Delete Add Beam, 2D elastic 3 Ok Options Ok Close. 50. Sections beam Common sections Select the correct section of the beam and input the values of w1, w2, w3 and t1, t2, t3 Preview Note down the values of area, Iyy. 51. Real constants - Add/Edit/Delete Add Ok Enter the values of area=5500, Izz=0.133e8, height=3 Ok - Close. 52. Material props - Material Models Structural Linear Elastic Isotropic - EX 2e5, PRXY 0.3 Ok. 53. Modeling Create Key points In active CS Enter the values of CS of each key points Apply Ok. Lines Lines Straight line Pick the all points Ok. 54. Meshing Mesh attributes All lines Ok. Meshing Size cntrls Manual size Lines All lines Enter the value of element edge length [or] Number of element divisions Ok. Mesh tool Mesh Pick all. SOLUTION: 20. Solution Define Loads Apply Structural Displacement - On key points Select the 1st key point ALL DOF Ok. On key points select the 2nd key point UY Ok. Force/Moment On key points Select the key point Ok direction of force/moment FY, Value = -1,000 (- sign indicates the direction of the force) Ok.

21. Solve Current LS Ok Solution is done Close. POST PROCESSING: 11. General post proc Element table Define table Add By sequence num SMISC,6 Ok SMISC,12 Ok LS,2 Ok LS,3 - Ok Close. Plot results Contour plot Nodal solution DOF solution Y component of displacement Ok. Contour plot Line element Res Node I SMIS 6, Node J SMIS 12 Ok. Contour plot Line element Res Node I LS 2, Node J LS 3 Ok FOR REPORT GENERATION: 10. File Report Generator Choose Append OK Image Capture Ok - Close.

RESULT:
Thus the stress analysis of beam is done by using the ANSYS Software.

STRESS ANALYSIS OF BEAM

1ooo N

All Dimensions are in mm Youngs Modulus Poissons Ratio = 200 GPa = 0.3

PREPARED AND PUBLISHED BY:


Mr.V.P.SURESH KUMAR M.E., M.I.ST.E.
Assistant Professor, Department of Mechanical Engineering, P.A.College of Engineering and Technology, Pollachi, Coimbatore - 642 002. Email: vpsuresh4@gmail.com

Potrebbero piacerti anche