Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Introduction
In this Packet Tracer Practice Skills-based Assessment, you will: complete the configuration of a partially configured network establish connectivity to the West Region and the Internet through the use of static and dynamic routing verify connectivity
Addressing Table
Device Interface S0/0/0 up EastHQ S0/0/1 do S0/1/0 up S0/1/1 up Fa0/0 E-Branch1 Fa0/1 S0/0/0 S0/0/1 Fa0/0 E-Branch2 Fa0/1 S0/0/0 S0/0/1 EPC1 EPC2 EPC3 EPC4 NetAdmin NIC NIC NIC NIC NIC Address 192.168.1.249/30 192.168.1.253/30 209.165.201.6/30 192.0.2.2/30 192.168.0.1 /25 192.168.0.129 /25 192.168.1.250 /30 192.168.1.245 /30 192.168.1.1 /26 192.168.1.65 /26 192.168.1.254 /30 192.168.1.246/30 192.168.0.2 /28 192.168.0.254 192.168.1.2 /26 192.168.1.126 192.168.1.66 /26 Subnet Mask 255.255.255.252 255.255.255.252 255.255.255.252 255.255.255.252 255.255.255.128 255.255.255.128 255.255.255.252 255.255.255.252 255.255.255.192 255.255.255.192 255.255.255.252 255.255.255.252 255.255.255.128 255.255.255.252 255.255.255.192 255.255.255.192 255.255.255.192 Default Gateway N/A N/A Internet 192.0.2.1 N/A N/A N/A N/A N/A N/A N/A N/A 192.168.0.1 192.168.0.1 192.168.1.1 192.168.1.1 192.168.1.65
Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode is class.
The privileged EXEC mode uses the following encrypted password: class.
Enable Telnet and console line logins and use the following password: cisco. EB2(config)#line vty 0 4 EB2(config)#password class EB2(config)#login EB2(config)#exit
Configure the banner message-of-the-day as Authorized access only! EB2(config)#banner motd %Authorized access only!% b. Using the Addressing Table, configure and activate all the necessary interfaces on E-Branch2. c. Configure correct host IP addressing. EB2#show ip interface brief EB2#show ip route
Configure EPC2 with the last IP address in the subnet. 192.168.0.254 255.255.255.128 Default gateway 192.168.0.1
Configure EPC4 with the last IP address in the subnet. 192.168.1.126 255.255.255.192 Default gateway 192.168.1.1
EastHQ (config-if)#no shutdown EastHQ (config-if)#exit EastHQ (config)#interface serial0/0/1 EASTHQ(config-if)#ip address 192.168.1.253 255.255.255.252 EASTHQ(config-if)#no shutdown EASTHQ(config-if)#exit EASTHQ(config)#interface serial0/1/0 EASTHQ(config-if)#ip address 209.165.201.6 255.255.255.252 EASTHQ(config-if)#no shutdown EASTHQ(config-if)#exit EASTHQ(config)#interface serial0/1/1 EASTHQ(config-if)#ip address 192.0.2.2 255.255.255.252 EASTHQ(config-if)#no shutdown EASTHQ(config-if)#exit
Configure a default route on EastHQ to send to the Internet all other traffic for destinations that are not found in the EastHQ routing table. Use the exit interface argument. EastHQ(config)#ip route 0.0.0.0 0.0.0.0 serial0/1/0
EastHQ(config)#router eigrp 100 EastHQ(config-router)#network 192.168.1.248 0.0.0.3 EastHQ(config-router)#network 192.168.1.252 0.0.0.3 EastHQ(config-router)#no auto-summary EastHQ(config-router)#ip default-network EastHQ(config)#interface serial0/1/0 EastHQ(config-if)#no eigrp 100 EastHQ(config)#interface serial0/1/1 EastHQ(config-if)#no eigrp 100 ----------------------------------------EB1(config)#router eigrp 100 EB1(config-router)#network 192.168.0.0 0.0.0.127 EB1(config-router)#network 192.168.0.128 0.0.0.127 EB1(config-router)#network 192.168.1.248 0.0.0.3 EB1(config-router)#network 192.168.1.244 0.0.0.3 EB1(config-router)#passive-interface fa0/0 EB1(config-router)#passive-interface fa0/1 EastHQ(config-router)#no auto-summary EB1(config-router)#CTRL+Z -----------------------------------------EB2(config)#router eigrp 100 EB2(config-router)#network 192.168.1.244 0.0.0.3 EB2(config-router)#network 192.168.1.0 0.0.0.63 EB2(config-router)#network 192.168.1.64 0.0.0.63 E B2 ( conf ig-rout e r) # ne t work 192.168.1.252 0.0.0.3 EB2(config-router)#passive-interface fa0/0 EB2(config-router)#passive-interface fa0/1 EastHQ(config-router)#no auto-summary EB2(config-router)#CTRL+Z
EB2(router-config)#network 192.168.1.0 0.0.0.63 EB2(router-config)#end summary routes EB1(config)interface serial0/0/0 EB1(config-if)#ip summary-address eigrp 5 192.168.0.0 255.255.255.0 EB1(config-if)#end EB1(config)interface serial0/0/1 EB1(config-if)#ip summary-address eigrp 5 192.168.0.0 255.255.255.0 EB1(config-if)#end EB2(config)interface serial0/0/0 EB2(config-if)#ip summary-address eigrp 5 192.168.1.0 255.255.255.128 EB2(config-if)#end EB2(config)interface serial0/0/0 EB2(config-if)#ip summary-address eigrp 5 192.168.1.0 255.255.255.128 EB2(config-if)#end
Version 1.0 Created in Packet Tracer 5.3.1.0044 and Marvel 1.0.1 All contents are Copyright 1992 - 2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.