Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Civil Works
S.No. Description Amount in `
1 2 3 4 5 6 7 8 9
EARTH WORK CONCRETE WORKS MASONARY WORKS FLOORING and DADO WORKS FINISHING WORKS DOORS AND WINDOWS STEEL WORKS ROOFING & WATERPROOFING WORKS MISCELLANEOUS WORKS Total
3,629,274.27
Amount in `
All the rates should be inclusive of scaffolding, curing at all levels and height
EARTH WORK
Earth work in excavationby mechanical means (Hydraulic excavator/manualmeans) including disposal of excavated earth, lead upto 50m and lift upto 1.5m; disposed earth to be levelled and neatly dressed In all kinds of soils - soft, hard Depth upto 1.5 mtr Extra for additional lift of 1.5m or part thereof Hard Rock without blasting upto 1.5 mtr Extra for additional lift of 1.5m or part thereof Filling in plinth or wherever called for as per directions of the Architect, in layers not exceeding 150mm thick (compacted) including watering, ramming, consolidating and dressing etc. Soling with stone aggregates upto 40mm size including watering ramming consolidating and filling voids with fine sand etc complete. With river sand brought from outside including loading, unloading and handling BackFilling available excavated earth ( excluding rock ) in sides of foundations upto plinth in layers not exceeding 20cms. In depth, compacting each deposited layer by ramming after watering with lead upto 50cm and lift upto 1.5m including cost of all labour complete as per specifications Providing and injecting,chemical emulsion for Pre-constructional Anti termite Treatmeny creating continous chemical barrier under and around the column pits, walls, trenches, basement excavation,top surface of plinth filling, junction of wall and floor, along the external perimeter of building, expansion joints, over the top of pipes and conduits, with chloropyriphos emulsifiable concentrates of 20% concentration, including the cost of chemical, diluting in water to one percent concentration , labour, HOM of equipments all complete as per specifications.. Only plinth area shall be measured
TOTAL TO SUMMARY
1.1 a) b) c) d) 1.2 a) b)
161 RO 40 RO
32184 28161
17 13
Cum Cum
949 817
16040 10259
2.0
141
Cum
55
7777
3.0
167
Sqm
120
20040
114,461
CONCRETE WORKS
Providing & laying PCC in foundation 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) including cost of centering, shuttering, mechanically mixing, vibrating, curing etc. complete as per the drawings and the directions of Engineer- In-charge Providing & laying Lean concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation and plinth ncluding cost of centering, shuttering, mechanically mixing, vibrating, curing etc. complete as per the drawings and the directions of Engineer- In-charge
Providing & laying cement concrete M 25 excluding cost of centering, shuttering and reinforcement but including mechanically mixing, vibrating, curing etc. complete as per the drawings and the directions of Engineer- In-charge In Sub- structure ( Till Plinth Lvl. Top) - Foundations, Plinth beams Column etc. In Superstructure ( Above Plinth lvl) - Columns, Beams, Slabs, staircase, steps Lintel, chajja etc. In sloping roof and gutter
2.1
Cum
3172
24726
2.2
Cum
3562
22365
2.3 a) b) c)
9 48 7.5
2.4
Providing & Laying reinforcements ribbbed tor/ TMT Bars of various diameters of grade Fe 415 conforming to IS code 1786 - 2008 for reinforced concrete work at all Height/ Levels including cutting, bending, binding with annealed 18G MS binding wire, placing in position as IS 2502 Providing centering & shuttering including strutting and propping etc. and removal of form work at all depths, heights and shapes
In Sub- structure ( Till Plinth Lvl. Top) - Foundations, Plinth beams Column etc. In Superstructure ( Above Plinth lvl) - Columns, Beams, Slabs, Lintel, chajja etc. In Staircase, steps etc. Shuttering in circular column
6248
kg
58
362412
2.5 a) b) c) d)
69 501 41 10.54
2.6
Providing and making Plinth Protection 50mm of Cement Concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) over 100 mm stone well rammed and consolidated and grouted with fine sand including finshing the top smooth , the rate shall be inclusive of shuttering
8.5
Sqm
380
3221
Amount in `
2.7
All the rates should be inclusive of scaffolding, curing at all levels and height Providing & laying 40mm thick damp proof course of CC 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm and down gauge) providing and applying a coat of hot bitumen( 80/100 ) @ 1.70 Kg/Sqm. The rate shall be inclusive of 12 Sqm shuttering, providing and mixing water proofing compound @ 1 kg. per bag of cement (with CICO No. 1 or equivalent approved). Providing and laying 1:3:6 screed (1 cement : 3 coarse sand : 6 graded stone aggregate 12.5 mm nominal size) over existing slab, laid to slope after proper hacking of the old concrete surface. Providing & laying RCC 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12mm nominal size) for cill of windows including projections, mouldings ,all as per drawing. The rate shall be inclusive of shuttering whereever required
TOTAL TO SUMMARY
300
3606
2.8
Cum
3562
17243
2.9
Cum
4800
4800 931,503
MASONARY WORKS
Providing and laying Solid Concrete block masonary of crushing strength 4 Mpa 200mm thk. in CM 1:4 (1 cement :4 coarse sand) at all floors and levels. The rate shall include scaffolding & curing etc. complete. The work shall be done in acordance with IS 2185 - Part 1 and as per the drawings and the directions of Engineer- Incharge Providing and laying Solid Concrete block masonary of crushing strength 4 Mpa 100 mm thk in CM 1:4 (1 cement :4 coarse sand)at all floors and levels , partition walls or whereverrequired as shown in the drawings. The rate includes providing and placing in position 2 nos 6 mm dia. MS bars at every 3rd course of masonry work, scaffolding & curing etc. complete. The work shall be done in acordance with IS 2185 - Part 1 and as per the drawings and the directions of Engineer- In-charge Providing & laying hammer dressed hard stone( locally available) random rubble masonary in CM 1:6 (1 cement :6 coarse sand), including cost of scaffolding , curing all complete. Providing & laying hammer dressed hard stone( locally available) random rubble masonary in CM 1:5 (1 cement :5 coarse sand) including cost of scaffolding , curing all complete. Providing & laying burnt brick masonary work with approved quality of non-modular bricks of standard size class designation 50( table mounted ) in CM 1:4 (1 cement :4 coarse sand) in staircase steps including cost of scaffolding , curing all complete.
TOTAL TO SUMMARY
3.1
75
Cum
5853
441187
3.2
Cum
6146
23286
3.3
57
Cum
2300
131346
3.4
RO
Cum
2350
3.5
Cum
4546
4546 600,365
FLOORING WORKS
Providing & laying minimum 20mm thk polished Shahderali stone slabs uniform shade in balcony, terrace and common spaces flooring using 20mm thk.( avg.) Cement Mortar 1:4 over exisiting Concrete bed laid to line and level and jointed with cement slurry mixed with pigment to match the shade of the stone, including the cost of materials, labour, curing, polishing all complete as per the specifications and as per the directions of Engineer-in-charge. Basic Rate - Rs.625 / sq.m Providing & laying minimum 20mm thk polished Shahderali stone slabs uniform shade in steps, skirting using 12mm thk. Cement Mortar 1:3 laid to line and level and jointed with cement slurry mixed with pigment to match the shade of the stone, including the cost of materials, labour, curing, polishing all complete as per the specifications and as per the directions of Engineer-in-charge.Basic Rate - Rs. 940/ sq.m Providing and laying of Pergo Pre-laminated flooring, 8 mm thk. of over 0.2mm thick alkali resistant polyethylene sheet with a 1.5mm extruded ployethylene foam backing laid over existing screed as shown in the drawings.Rate includes the cost of door profiles, top beading, edge finsihing, skirting etc. any protection required , all complete as per manufacturer's specification, drawings and as directed by the architect / client. Providing and fixing skirting of Pergo Pre-laminated flooring as per manufacturer's specification, drawings and as directed by the architect / client. Providing and laying mm thick anti-skid glazed vitrfied floor tiles of size 600 x 600 mm in over 25 mm thick( avg.) bed of cement mortar 1:4 ( 1 cement : 4 coarse sand ) including pointing in white cement mixed with pigment of matching shade complete. Make Kajaria Fog perla - etc as per finishing schedule
4.1
77
Sqm
1032
79441
4.2
30
Sqm
1312
39723
4.3
43
Sqm
1938
83579
4.3a
44
rm
155
6820
4.4
109
Sqm
1650
180337
Sqm
1680
15259
Amount in `
All the rates should be inclusive of scaffolding, curing at all levels and height Providing and laying mm thick anti-skid glazed vitrfied floor tiles of size 600 x 600 mm in over 25 mm thick( avg.) bed of cement mortar 1:4 ( 1 cement : 4 coarse sand ) 4.5 a 15 Sqm including pointing in white cement mixed with pigment of matching shade complete. Make Kajaria Desert Crema - etc as per finishing schedule 4.5 b Same as above Skirting 12mm thk. Cement Mortar 1:3 2 Sqm Providing and laying 7.7mm thick matte finish anti-skid ceramic floor tiles of size 300 x 300 mm in Kitchen and Toilets, over 25 mm thick( avg.) bed of cement mortar 1:4 ( 1 cement : 4 coarse sand ) including pointing in white cement mixed with pigment of matching shade complete. Make - Kajaria Granelia Crema / Graneila Grey, Morroco Grey etc as per finishing schedule Same above but in skirting with 12mm thk. Cement Mortar 1:3 Providing and laying 6.8mm thick matte finish ceramic WALL tiles in Toilets in dado over 12mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) including pointing in white cement mixed with pigment of matching shade complete. Make Kajaria Pixel Grey blue, brown as per finishing schedule Providing and laying 6.8mm thick matte finish ceramic WALL tiles in Kitchen in dado over 12mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) including pointing in white cement mixed with pigment of matching shade complete. Make Kajaria Blanco Nieve as per finishing schedule Providing and laying 25mm thk cement concrete with mix 1:2:4 (1-cement : 2-coarse sand : 4-20mm nominal size of stone aggregate) Providing & laying minimum 25mm thk polished grey granite stone slabs in coping, Basic Rate - Rs. 1200/ sq.m including making drip course etc. as shown in the drawings Providing and fixing 20mm thk, prepolished grey granite stone in window cill laid over base of 20mm thk in CM 1:4 & joints neatly finished with cement of matching colour including chamfering and polishing of edges etc. as per drawing. (Rate shall include chamfering, levelling and polishing of edges) Basic Rate - Rs. 925/ sq.m Providing & laying 20mm thick pre-polished black granite stone slab counter of any shade laid over base of 20mm thk in CM 1:4 & joints neatly finished with cement of matching colour including chamfering and polishing of edges and cutting of holes for sink & wash basin etc. as per drawing. (Rate shall include chamfering, levelling and polishing of edges) Basic Rate - Rs. 1300/ sq.m Providing and fixing 80mm thk. M30 Concrete pavers made by block making machine with strong vibratory compaction and of approved size, design and colour, pattern laid over compacted bed of 50mm thick course sand filling the joints with coarse sand. Basic Rate - Rs. 755/ sq.m
TOTAL TO SUMMARY
1535
23214
1550
3196
4.6
30
Sqm
725
21854
4.6a
RO
Sqm
761
4.7
78
Sqm
745
58292
4.8
Sqm
606
4454
4.9
16
Sqm
192
3116
4.10
15
Sqm
2415
36924
4.11
Sqm
1975
12313
4.12
Sqm
2525
19546
4.13
29
Sqm
1230
35627 623,697
5 5.1
FINISHING WORKS
Providing & applying (12-15)mm avg. thick internal wall plaster in CM 1:6 ( 1 cement : 6 fine sand using 25% coarse sand and 75% river sand) at all heights and levels including scaffolding, curing, corner guards, chicken wire mesh etc. complete. 18mm external plaster in two coats - 12mm thick 1:5 Cement mortar ( 1: 5 Coarse sand ) for under 6mm thick 1:3 Cement mortar ( 1: 3 Fine sand ) for top coat using waterproofing compound at 1kg.per cement bag( for both coats) and finished rough with sponge at all heights and levels including scaffolding, curing, corner guards, chicken wire mesh etc. complete. 18mm plaster over tile dado and tile skirting in two coats - 12mm thick 1:5 Cement mortar ( 1: 5 Coarse sand ) for under 6mm thick 1:3 Cement mortar ( 1: 3 Fine sand ) for top coat and finished rough with sponge at all heights and levels including groove making, scaffolding, curing, chicken wire mesh etc. complete. Providing and fixing dholpur stone 20mm mm thick as wall cladding over 20mm thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the stone, including fixing cramps at supports wherever required, forming groove of uniform size Groove as per approved pattern in Dholpur stone and finishing the groove complete as per Architectural design and specifications, scaffolding, curing etc. at all levels and heights etc. complete. Basic Rate - Rs. 650/ sq.m 168 Sqm 165 27757
5.2
338
Sqm
242
81850
5.3
275
Sqm
235
64692
5.4
85
Sqm
1250
106827
Providing and fixing MS Angle 30 x 30 x 5mm for supporting external stone cladding 5.4 a in unsupported areas as shown in the drawings, including screwing it to the wall surface.
RM
125
625
Amount in `
5.5
All the rates should be inclusive of scaffolding, curing at all levels and height Providing & applying 6mm thick plaster in CM 1:3 (1 cement : 3 coarse sand using 25% coarse sand and 75% fine sand) on ceiling including hacking the surface, 268 Sqm scaffolding, curing etc. at all levels and heights etc. complete. Providing and applying two coats of Berger Weather proof exterior texture finish paint over plastered wall & external ceilings,. with two coat of primer and wall putty . The rates shall be inlcusive of primer and paint , any minor repair if required as per the directions of Engineer-in-charge. The paint shall be of make Berger - weather coat category or any approved make of Nerolac , Asian . Providing and applying two coats of Berger Weather proof exterior smooth finish paint over plastered external ceiling with two coat of primer and wall putty . The rates shall be inlcusive of primer and paint , any minor repair if required as per the directions of Engineer-in-charge. The paint shall be of make Berger - weather coat category or any approved make of Nerolac , Asian . Providing and applying emulsion paint to Internal walls and internal ceiling, staircases with oil bound washable distemper of approved colour brand and maufacturer to give an even shade. The paint shall be of make Berger or any other approved quality. The work shall be done as per manufactueres specifications Providing & applying 4-6mm thick POP Punning for ceiling at all height and levels finished with smooth surface including groove making, scaffolding, curing, Corner Guard, chicken wire mesh (Approved make and guage) etc. complete.
TOTAL TO SUMMARY
127
34092
5.6
338
Sqm
245
82864
5.7
24
Sqm
230
5500
5.8
376
Sqm
90
33837
5.9
RO
Sqm
80 438,044
Providing & Fixing of powder coated Single leaf Aluminium Openable doors frames wherever required fixed with snap beading & hardwares etc. other appropriate sections of approved make conforming to IS:733 and IS : 1285 of required shade, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/ Neoprene felt etc. 6.1 Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, CP brass/stainless steel screws, . as per design, all complete as per architectural drawings and the directions of Engineer-in-charge. The rate shall be inclusive of Providing & fixing rough ground, EPDM / Neoprene Gasket, snap beading etc all complete. While arriving at the rate of item weight @ 5.85 kg/ sq.m is considered. Item in 6.12 shall be paid extra. Rest all shall be inclusive in the rates Contractor shall submit shop drg. for approval before start of work any order of material. Providing and fixing in position powder coated alluminium fixed window fully glazed or of any size as shown in the drawings as as directed by Engineer-in-charge with all necessary alluminium section including such snap beadings, hold fast, etc. complete. While arriving at the rate of item weight @ 6.0 kg/ sq.m is considered. Other specifications same as Item no 6.1 Providing and fixing in position powder coated alluminium partly fixed partly openable window shutter with Double leaf frame of any size as shown in the drawings as directed by Engineer-in-charge with all necessary alluminium section including such snap beadings, hold fast, etc. complete. While arriving at the rate of item weight @ 7.5 kg/ sq.m is considered. Other specifications same as Item no 6.1 2 Sqm 2400 4990
6.2
3.5
Sqm
2475
8539
6.3
30
Sqm
3250
97738
Providing and fixing in position powder coated alluminium partly fixed partly sliding window shutter with Double leaf frame of any size as shown in the drawings as 6.3 b directed by Engineer-in-charge with all necessary alluminium section including such snap beadings, hold fast, etc. complete. While arriving at the rate of item weight @ 7.25 kg/ sq.m is considered. Other specifications same as Item no 6.1 Providing and fixing in position powder coated alluminium fully openable window shutter with double leaf frame or of any size as shown in the drawings as directed by Engineer-in-charge with all necessary alluminium section including such snap beadings, hold fast, etc. complete. While arriving at the rate of item weight @ 7.25 kg/ sq.m is considered. Hardware, glass, hinges shall be paid extra Other specifications same as Item no 6.1
Sqm
3200
20535
6.4
17
Sqm
3000
49641
Qty
Unit
Rate
Amount in `
All the rates should be inclusive of scaffolding, curing at all levels and height
6.5
Sqm
2825
3331
6.6
Sqm
2965
10585
6.7
26
Sqm
865
22897
6.8
Providing & fixing 35mm flush door shutters (Anchor/ Kitply/ Sitapur/ Greenlam/Swastic or equivalent appd) core of block board construction, syntthetic resin bounded chemically impregnated with frames of first class hard wood & well matched 3mm thick ply on both faces including minimum 3mm thick teakwoodlipping with matching SS screws for each shutter.
Moulded With both sides commerical ply paint ( Asian Paint - PU Pallette ) With both sides teak ply laminate of Greelam make as shown in the finishing schedule Providing and fixing 1st class chapwood work in frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position all complete as shown in the drawings and per the directions of engineer incharge. Basic rate of Chapwood assumed as Rs. 1200/ cft Providing and fixing GI FLY mesh with avg. width aperture 1.40mm and wire of dia. 0.63mm in doors and windows as shown in the drawings Providng and fixing 5.5 mm thick clear float glass in shutters of windows with all accessories
a) b)
22 4
Sqm Sqm
2200 3200
47542 12842
6.9
0.70
Cum
72000
50183
31 51
Sqm Sqm
475 550
14568 28187
Providing & fixing hardware fittings of Aluminium hardware to doors /windows complete with nuts, bolts, screws and accessories.
Tower Bolt - 9.5mm x 300mm - NLTL-01 Tower Bolt - 9.5mm x 200mm - NLTL-01 Tower Bolt - 9.5mm x 150mm - NLTL-01 Baby Latch NL3D-01 - 75 MM BUTT HINGE - 75x22mm x 2mm BUTT HINGE - 100x22mm x 3mm Pull Handle -NLPH30 Pull Handle -NL-CH-006 Window Stay 250mm Window Stay 250mm Mortise lock and handle - NLMOR-01 Door Stopper 01 - 150mm Providng and fixing in position 35mm shutters made of chap wood as shown in the drawings or directed bythe engineer-in-charge.forventilators including the cost of painting and screws but excluding hinges, handle etc. Extra over items 6.1 to 6.7 for increase in kg/sq.m weight for Aluminium after submission of shop drawings by the Contractor and it's approval from Architect. Deduct over items 6.1 to 6.7 for decrease in kg/sq.m weight for Aluminium after submission of shop drawings by the Contractor and it's approval from Architect. Providing and fixing 1st class teak wood strip 100x 45mm in sill and jamb of windows as shown in drawings , the rate shall include applynig one coat of wood primer and two coats of Apoclite satin enamel paint. Basic rate of Teakwood assumed as Rs. 2900/ cft TOTAL TO SUMMARY
2 35 25 10 58 106 8 52 21 4 5 18 1
nos nos nos nos nos nos nos nos nos nos nos nos
217 153 129 320 99 120 1684 815 336 3105 3561 284 3000
433 5340 3225 3196 5759 12739 13474 42396 7049 12420 17805 5114 2416
Sqm
6.14 6.15
RO RO
kg kg
415 415
6.16
19
rm
725
13558 516,502
Amount in `
All the rates should be inclusive of scaffolding, curing at all levels and height 7 7.1
STEEL WORKS
Providing and fixing steel work in built up sections / framed work including cutting, hoisting, fixing in position using structural steel etc. as given in the drawings. The rate shall be inclusive of welding, applying two coats of approved steel primer providing and fixing nut, bolts etc. all complete etc Providing and fixing steel work in Staircase , balcony Railing including cutting, hoisting, fixing in position using structural steel etc. as given in the drawings. The rate shall be inclusive of welding, applying two coats of approved steel primer providing and fixing nut, bolts etc. all complete etc Providing and painting Apcolite Premium Satin enamel (two or more coats) of approved shade and sample over Structural Steel. The rate shall be inclusive of cleaning the surfaces etc .all complete and as per the directions of engineer- incharge RO kg 72
7.2
247
kg
83
20487
7.3
1122
kg
5611
7.4
Providing M.S spiral staircase ( incl. railing) made out of 135 mm dia main vertical pipe 4.8mm thick with necessary M.S., steps made of 4mm thk. Chequred plate supported on MS Angle. The rate shall be inclusive of welding, applying two coats of 1000 approved steel primer providing and fixing nut, bolts, anti shrink grout etc. all complete etc Providing and fixing, making MS rungs of 26.9mm OD hollow section welded to MS flat into 500x200x200, as per details and pattern as shown in the drawings with one coat steel primer and two coats of synthethic enamel paint all complete. Providing and fixing MS ladder for shaft in double units fabricated at site with built up sections as per details and pattern as shown in the drawings with one coat steel primer and two coats of synthethic enamel paint all complete.
TOTAL TO SUMMARY
kg
95
95000
7.5
20
nos
310
6200
7.6
nos
11400
11400 127,298
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-incharge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. Laying brick bats with mortar using broken bricks/brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement:5coarsesand) admixed with water proffing compound conforming to IS:2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-Charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-charge. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and maing pattern of 300x300 mm square 3mm deep. The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and as directed and specified by the Engineer-in-Charge: With average thicknees of 120mm and minimum thickness at khurra as 65mm. Providing and laying Tapecrete water proofing in two coats as per manfacturer's specifications in toilets, balconies with 15 mm thk cement plaster with neat cement floating coat on top. Providing and laying gola 75x75mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with CM 1:3 (1 cement : 3 fine sand) as per standard design.
8.1
54
Sqm
700
37957
8.2
RO
Sqm
550
8.3
30
metre
96
2869
Amount in `
8.4
All the rates should be inclusive of scaffolding, curing at all levels and height Providing & applying vertically in postion 25mm thick damp proof course of CC 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm and down gauge) providing and applying a coat of hot bitumen( 80/100 ) @ 1.70 Kg/Sqm. The rate 20 Sqm shall be inclusive of shuttering,edge supports , providing and mixing water proofing compound @ 1 kg. per bag of cement (with CICO No. 1 or equivalent approved).
TOTAL TO SUMMARY
400
8000
48,826
MISCELLANEOUS WORKS
Providing and fixing wooden pergola ( Chap Wood ) with two coats of approved Apcolite satin Enamel Paint and one coat of approved wood primer as shown in the drawings and as directed by the engineer-in-charge. The rate also includes all SS shoe MS work like insert plate, etc. , carrying, lifting and tools, machinary required to carry out the works all heights and levels. Plan area shall be measured. For MS work the specs shall be same as that in 7.1 and 7.3 Basic rate of Chapwood Rs. 1200/ cft Providing and fixing Expansion Joint made of 140 x140x 10mm SS and MS plate and cover MS capped cylinder as shown in the drawings . The rate shall include all Reinforced bars, bolts, welding all complete. Including a coat of steel primer at all levels and floors. Providing and fixing Expansion Joint made of 140 x140x 10mm SS and MS plate and cover MS capped cylinder and making RCC bracket, shuttering, filling bitumen in joints etc. as shown in the drawings . The rate shall all Reinforced bars, bolts, paper joint, welding all complete. Including a coat of steel primer at all levels and floors. Providing and filling cast-in-situ foam block concrete of density 480 kg/cum in roof slab/ toilet and other similar locations in required thickness to level or in slope as directed laid, consolidated, etc., complete. Providing and constructing superior Indian teak wood hand rail as per detailed drawings or as directed by the Engineer, including painting with Apcolite Premium Asian Paint. Basic rate of Teakwood assumed as Rs. 2900/ cft Providing and fixing Manglore ( Master Bamboo Clay tiles ) Providing and laying mangalore tile over a bedding of 25mm thick ( avg) Cement Mortar 1:4 ( (1 cement : 4 Providing and fixing Aluminium Angle 25x25x3mm as per drawings under counter. Providing and fixing 50mm thick precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete excluding plastering of the jambs, sills and soffits as per manufactueres detail and specification FALSE CEILING WITH BISON BOARD. Providing and fixing Bison cement particle board 8mm thick with 600x600 mm grid system using frame of suspended grid system with galvanizedsteel `T section frame work of hot dipped galvanizedsteel precoated (exposed portion only), which includes flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centers to form 1200x600mm modules. Cut cross tees longer that 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200mm cross tees. Rate shall be inclusive of applying two coates of plastic emulsion paint to the particle board tiles as per manufacturer specification. Proving and fixing UPVC Gutter as per manufacturer's specifications at roof area, contractor should provide necessary detail and sample uPVC gutter matching with extreior detail and get them approved from the architect. Providing & fixing mirror of superior glass( of approved quality & make) and of required shape & size with 25 x 12.5 mm beading at edges of the mirror & 6 mm BWP ply at back with felt cloth backing complete as per drgs. & details Grassing with Doob Grass including watering and maintenanceof lawn for 30 days or more till the grass formsa thick lawn free from weeds and lit for moving including supplying good earth if needed complete in rows 15cm apart in each direction
TOTAL TO SUMMARY
9.1
14
Sqm
5670
77147
9.2
nos
1500
3000
9.3
rm
900
4675
9.4
0.5
cum
6000
3129
23 80 10
rm Sqm RM
9.8
15
Sqm
750
11160
9.9
34
Sqm
1065
35854
9.10
25
rm
700
17336
9.11
Sqm
2500
9020
9.12
21
Sqm
44
940 228,578