Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Specification:
Length: 1270mm(50) Wing span: 1465mm(57) Wing area: 36.3sq.dm (3.9sq.ft) Wing loading: 66g/sq.dm(21.6oz/sq.ft) Flying weight:2.4kg(5.2lbs) Radio: 4ch & 5servos Engine: 4-cycle 52-70 2-cycle 40-52 Motors: 4250 510KV ESC: 60A Battery: 6S 2200MAH 20C Propeller: 14*7
INSTRUCTION MANUAL
SAFETY PRECAUTIONS
(with 5 servos),
Li-Pox4 (2200mAh)
4-cycle 52-70.
Motor controller:60A
2 in Spinner
14"x7
We strongly recommend you use the thread lock for all the screws when you build your model.
Apply epoxy glue.
Warning Remove the covering with proper pressure to cut through only the covering itself.Otherwise, cutting down into the balsa structure may weaken the model part and cause accident. The pre-covered film on ARF kits may wrinkle due to variations of temperature.Smooth out as explained right.
Pre-cover the covering with clean cloth! Start at low setting. Increase the setting if necessary.If it is too high,you may damage the film.
Apply instand type CA glue to appropriate position of trailing edge and pin hinge.
2 6 2 2 2 2 2 2 8 2
Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents!
Collar (2mm)
Apply instant type CA glue to appropriate position of aileron and pin hinge.
Pin hinge(24x24mm) 6
Keep about 1mm width space between aileron and trailing edge.
Trailing edge
Collar
Aileron
Nut
1mm
Washer 2x6mm
Make sure they are in the right position while installing.
Screw 2x10mm
Secure the servo.Install the nylon control horn and connect the linkage.
TP Screw (2.3x12mm)
55
56
1
AILERON 40mm 40mm
Side View
50mm 50mm
1.5mm
AILERON
TP Screw (2.3x12mm) 8
Assemble the wings to the fuselage through the main wing joiner carefully.
57
58
Main wing joiner (16x494mm) Pin hinge(24x24mm) Tail landing gear(2mm) Tail wheel (30mm) Collar (2mm)
1 7 1 1 3 1 3 2 2
ELEVATOR
40mm 40mm
Top view
82mm
Cut away the covering in appropriate position in the fuselage to show the offered holes and slots like illustration.
10
Screw
Fix the wing to fuselage with screws throught the holes applied in the wings and fuselage.
Spring Washer
2 2
11
52
Trim the PVC part along the shaded line and glue it to the fuselage.
11
14
Keep about 1mm width space between the tailing edge and elevator.
Tailing edge
Pvc Pvc Screw (3x16mm) Washer (3x8mm) TP Screw (2.3x8mm) Ply (15x15x3mm)
1 1 2 2 7 7
Elevator
B'
A'
1mm
A=A' B=B'
50
Trim the PVC part along the shaded line and glue it to the cockpit.
53
According the engine mark out the conflictive position when assemble the cowling to fuselage.
12
Cut away the covering in appropriate position in the fuselage and vertical fin carefully and epoxy the vertical fin to fuselage.
15
51
54
13
16
1.5mm
2 2
7 7
Make sure hinges are mounted in the same line.
Pin hinge(24x24mm)
10
17
Glue the pin hinges to the rudder,drill a hole and trim a slot to appropriate position in the rudder. Pin hinge(24x24mm) 3
20
47
Cut away the covering in appropriate position in fuselage to show the offered slot for assembling the undercarriages.
Main landing gear LockNut (4mm) Screw (3x20mm) Washer (3x6mm) Wheel (55 mm) Washer (4x8mm) TP Screw ( 2.3x8mm)
3
1 2 6 6 2 4 2 2
2.5mm
Make sure hinges are mounted in the same line.
Pin hinge(24x24mm)
Screw (4x35mm)
18
Keep some space about 1mm width between the rudder and tail edge.
21
45
48
Insert the undercarriages to the fuselage, trim some holes to appropriate position for fixing the undercarriages.
Tailing edge
Rudder
Screw (4x35mm)
1mm
Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents!
TP Screw (2.3X8mm)
19
According to the illustration below bend the tail landing gear wire and cut off the surplus part. 25mm
22
46
49
2 4
TP Screw (2.3x12mm)
Screw (4x35mm)
CA
Washer (4x12mm)
50mm
Collar(2mm)
TP Screw (2.3x8mm) Nut (4mm)
aluminium plate (50X2mm) Tail landing gear(2mm)
Washer (3x6mm)
2 2 2
4.2mm
Blind Nut
Collar
TP Screw (2.3x12mm) 3
appropriate distance
6 6
39
42
Nut
25
5.2mm
Blind Nut
Nut
Nut (4mm) Linkage Stopper Plastic tube (2x400mm) Engine mount (52x86mm) Fuel tank (260cc) Rod (2x400mm) Motor mount box
Washer 2x5mm
Washer 2x5mm
Screw 2x10mm
Screw 2x10mm
40
Cut away the covering in appropriate position in the fuselage to show the offered hole as illustration.
43
Cut away the covering in appropriate position in the fuselage to show the offered hole as illustration.
23
26
4mm
Washer (4x8mm) Washer (4x8mm) Spring Washer (4mm) Nut (4mm)
Screw (4x20mm)
41
Assemble the servo to the hole and connect the elevator to the servo via linkage.
44
Assemble the servo to the hole and connect the rudder to the servo via linkage.
24
27
1 1 4 1 1
115mm
TP Screw (2.3x12mm)
4 4 1
28
31
34
Washer (2mm)
37
115mm
Washer (4x8mm)
Washer (2mm)
1 1 1 1 Screw (4x20mm)
29
32
35
38
4mm
Air pressure line Fuel spray line Fuel supply line
30
33
The consumers can also use motors for this plane.please find the assemble steps below.The front view when the motor install completion.
36
Control Horn(2mm) Clevis Screw (2x10mm) Nut (2mm ) Washer(2x6mm) Rod (2x300mm)
Washer (4x8mm) Screw (4x20mm)
2 2 2 2 2 2 2 8
motor dimension
O 42x50mm