Sei sulla pagina 1di 7

1

A network administrator has received complaints about slow network performance on one segment of a Layer 2 switched network. To determine wh types of traffic are on the segment, the administrator decides to configure SPAN to allow the installation of a packet sniffer. Which two items must be configured to allow SPAN to function? (Choose two.) a monitored port or VLAN the threshold value of monitored traffic the port that connects to the packet sniffer the sampling rate of the monitored port or VLAN the dot1q encapsulation on the monitored port

What is the effect of the snmp-server ifindex persist command? All SNMP messages will remain in memory until the next interface reset. The SNMP community string index will be encrypted and stored in NVRAM. The SNMP interfaces for all devices in the community will be synchronized in NVRAM. The SNMP interface index for each interface will stay the same, even if the device is rebooted.

Refer to the exhibit. A network administrator used an extended ping to verify connectivity to a remote location. The ping indicated a 50 percent pack loss. What could be the cause of the problem? NAT is filtering the echo reply packets. The packet size is exceeding the MTU. An ACL is blocking the echo reply packets. An ACL is blocking the echo request packets. Load balancing is occurring with packet loss on one path. 4

A network administrator has noticed an unusual amount of traffic being received on a switch port that is connected to a college classroom computer. Which tool would the administrator use from the NOC to take a closer look at the type of traffic that is being sent to the PC? RSPAN a port scanner an IDS the show interfaces fa0/x command SNMP agent software

A newly established branch office is reporting connectivity issues with the server farm that is located at the main office. The network administrator

suggests that the problem could be with the path MTU. How could the network administrator verify that this is the problem? Consult the network documentation to determine the MTU. Use the traceroute command to determine where packets are being lost. Adjust the MTU parameter on the router in the server farm to determine the acceptable path MTU. Use the extended ping option to send packets of increasing size to the destination to determine the path MTU. 6

Refer to the exhibit. What information does this output provide? The router has a connected default route. The router is installing five routes in its routing table. The router received routing updates from 10.89.64.28. The router is advertising its routes to the router with the address 10.89.94.31. 7 Which two symptoms would the show processes cpu command be helpful in troubleshooting? (Choose two.) no link lights failed Telnet sessions to router output queue drops input queue drops excessive collisions 8 Embedded Event Manager events can be triggered based on which three Cisco IOS subsystems? (Choose three.) changes in the CEF table changes in the routing table counter changes

execution of a Tcl script SNMP MIB object changes syslog messages 9

Refer to the the exhibit. Given the partial NetFlow configuration, which command sequence is required to forward the traffic statistics of interfaces Fa and Fa0/1 to the NetFlow traffic collector? R1(config)# interface FastEthernet1/0 R1(config-if)# ip flow egress R1(config-if)# exit R1(config)# interface FastEthernet1/0 R1(config-if)# ip flow ingress R1(config-if)# exit R1(config)# ip flow-control source Fa0/0 R1(config)# ip flow-control source Fa0/1 R1(config)# exit R1(config)# ip flow-control source Fa1/0 R1(config)# exit R1(config)# interface FastEthernet0/0 R1(config-if)# ip flow ingress R1(config-if)# exit R1(config)# interface FastEthernet0/1 R1(config-if)# ip flow ingress R1(config-if)# exit 10

Refer to the exhibit. A network administrator issues a ping command as shown. What could be the reason for the failure of the ping to host 172.16.1 Host 172.16.1.5 is not reachable. Ping packets are being blocked by an ACL somewhere along the path to 172.16.1.5. Packets with the DF bit set cannot be transported over a Frame Relay network. An interface of the device along the path to the destination cannot accommodate the large packets. 11

Refer to the exhibit. A network administrator is testing connectivity to a remote host. Based on the command output, what conclusion can be made? A problem exists with Layer 3 connectivity. A connection can be established to all TCP ports on the remote host. The Open response on R1 indicates that the port (application) is active. A Telnet connection to the specified host port is unsuccessful. 12

Refer to the exhibit. The administrative assistant using the user PC complains that retrieving e-mail has been slow for the past 30 minutes. The netw administrator using the administrative PC sees the same results. In an effort to identify the exact problem area, the network administrator accesses services server to retrieve performance data from the SQL server about the mail server. Which device in this scenario is considered an SNMP NMS? administrative PC user PC SQL server IT services server mail server 13

A router is currently running both OSPF and BGP. The administrator issues the command show ip route | exclude ^B. What routes will be displaye only OSPF routes only BGP routes both BGP and OSPF routes both OSPF and directly connected routes both BGP and directly connected routes

14

The administrator would like to see the commands that are associated with the serial1/0 interface. The administrator enters the command show run config | section interface serial1/0 but does not receive a response. What could be the problem? The interface is down. The interface does not have any commands associated with it. The interface serial1/0 keyword looks for an exact match and should specify interface Serial1/0. The administrator should have entered the command show run | i interface serial1/0.

15

A network administrator types the following command on a router: R1# show ip ospf interface | include is up|Cost

Which response would most likely be displayed after issuing this command? Ethernet0 is up, line protocol is up Internet Address 10.10.10.1/24 Area 0 Process ID, Router ID 192.168.45.1, Network Type BROADCAST, Cost: 10 Neighbor 10.19.199.137, interface address 192.168.80.37 In the area 0.0.0.0 via interface FastEthernet0/0 Neighbor priority is 1, State is FULL Cost is 100 FastEthernet0/0 is up, line protocol is up Cost: 1 Loopback22 is up, line protocol is up Process ID 1, Router ID 111.111.111.111, Network Type LOOPBACK, Cost: 1 17 By default, Cisco routers send which type of SNMP traps? SNMP version 1 SNMP version 2c SNMP version 3 SNMP versions 1 and 2c SNMP versions 1, 2c, and 3 18 A network administrator has just issued this command: R1# debug ip packet 5 detail Why would the network administrator issue the debug ip packet 5 detail command? to limit the output to five lines to limit the output to every fifth packet and include all details that are associated with the packet to limit output to packets that are matched by an ACL to increase the amount of given output to include the first five fields of the IP header to increase the amount of given output by including more detailed information 19 What will occur when the no debug all command is issued? Options for debugging will be displayed. All debugging output will immediately stop. No further debugging information will be generated. General debugging on the router will be disabled, but specific debugging will continue. 20

Refer to the exhibit. What tool was used to generate the output that is displayed? NetFlow

RSPAN SNMP SPAN syslog

Potrebbero piacerti anche