Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
The following safety precautions are given throughout this manual. They must be strictly followed to protect
those who install, use or maintain this product as well as to prevent other people’s injuries and property
damages.
WARNING
Indicates a situation where disregarding the suggestions could result in death or serious injury.
CAUTION
Indicates a situation where disregarding the suggestions could result in injury or product damage.
Indicates a matter of which care should be taken. Indicates a matter which is forbidden.
In this instruction manual, some procedures require a qualified in-shop maintenance person or industry
specialist. For such instructions, a qualified person must take care of the jobs.
• Otherwise an electric shock, machine trouble, or a serious accident may result.
• Replacing the machine parts, inspecting and maintaining the machines, and troubleshooting must be assigned only to
a qualified in-shop maintenance person or industry specialist. This booklet gives instructions that hazardous jobs in
particular must be handled by an industry specialist. Qualified in-shop maintenance person and industry specialist are
defined as follows.
Industry specialist
•An industry specialist must be engaged in designing, manufacturing, inspecting and servicing amusement machines.
Or he or she must have an education in electrical, electronic and mechanical engineering, and routinely maintain and
repair amusement machines.
3
Precautions for use Precautions for use
Setting Up Operation
Be sure to consult your nearest dealer when setting up, Be sure to use indoor wiring for within the specified If there is any abnormality such as smoke, Do not use this product anywhere other than
moving or transporting this product. voltage range. For extension cord, use indoor wiring bad smell or abnormal noise being emitted industrial areas.
• This product should not be set up, moved or transported by of the specified rating or more. • Using in a residential area or an area next to a
from the machine, immediately turn OFF the residential area could affect signal reception of
any one other than an industry specialist. Doing so could • Failure to do so could result in fire or equipment failure. main power switch and unplug the power cord radios, television sets, telephones, etc..
result in injury or product damage. Do not give impact to the glass cover.
• When installing this product, set the 4 leg levelers evenly Be sure to use the attached power cord. from the receptacle to stop operating it. • Otherwise, it may result in an unexpected accident or
on the floor and make sure that the product is installed • Otherwise a fire or machine trouble may result. • Using the machine in abnormal conditions could result injury.
stably in a horizontal position. Unstable installation may in fire or accidents.
result in injury or accident. Never plug more than one cord at a time in • Please do not play this game if
• When installing this product, use caution not to apply the electrical receptacle. In case of abnormality
1you have been drinking.
undue force to opening and closing parts and other • Doing so could result in fire or electrical shock. 1. Turn OFF the main power switch. 2you are tired or sick or have been recently sick.
movable parts. Otherwise, injury and accident may result, 2. Unplug the power cord from the receptacle. 3you think you might be pregnant.
or the product may be damaged. Do not lay the power cord where people walk 3 . Contact your nearest dealer. 4you have a pace maker.
through. You may trip on or stumble over 5 you have previously experienced muscle spasms or loss
This product is an indoor game machine. Never the cord. of consciousness by watching a TV screen.
set the game machine up outside. • You may stumble down and get injured, or damage the • Punching the pads too aggressively may cause injury to
• Setting this product up outside could result in power cord. Do not leave the power cord plugged in
your hands.
accidents or equipment failure. improperly or covered with dust. • This game is designed for one player only. Do not play
Be sure to ground this product. • Doing so could result in electrical shock or fire, with 2 or more people.
Do not set the game machine up near • Otherwise an electrical shock or machine so inspect the power cord periodically.
trouble may be caused. • When playing, please be aware of your surroundings.
emergency exits.
• Doing so could block exits in time of emergency
and could result in death or serious injury. Do not apply a strong force for moving the Do not plug or unplug the power cord with wet
machine. hands.
Do not set the game machine up. • Otherwise, it may result in an accident or • Doing so could result in electrical shock.
1. In a place exposed to rain or moisture. breakage of the units.
2. In a place exposed to direct sunlight. In handling the power cord, follow the
instructions below.
3. In a place exposed to direct heat from air-conditioning and Clearance of 100 mm (3.94in) or more should be • Otherwise, fire or electrical shock may result.
heating equipment, etc.. created between the game machine and walls.
4. Near hazardous flammable substance such as thinner and • Otherwise the machine (s) cannot be ventilated well,
kerosene. resulting in malfunction. • Do not damage the power • Do not modify the power
• Otherwise an accident or malfunction may result. cord. cord.
Do not change the DIP switch setting of this product • Do not bend the power • Do not twist the power
Do not place containers holding chemicals or to other than factory setting. cord excessively. cord.
water on or near the game machine. • Otherwise, the game can not be played properly. • Do not heat the power • Do not pull the power
• Electrical shock or damage could be caused by cord. cord.
water or foreign matter entering the inside of the machine. • Do not bind the power • Do not stand on the
cord. power cord.
Do not place objects near the ventilating holes. • Do not sandwich the • Do not drive a nail into the
• Doing so could cause the internal temperature to rise power cord. power cord.
excessively, resulting in fire or equipment failure.
If the power cord or power plug becomes damaged,
Do not bend the power cord by force or place stop using the machine immediately and ask your
heavy objects on it. nearest dealer to replace the parts.
• Doing so could result in electrical shock or fire. • Using a damaged power cord or power plug could
result in fire or electrical shock.
Never plug or unplug the power cord with wet
hands.
• Doing so could result in electrical shock or fire.
4 5
Precautions for use Safety Instructions
These safety instructions are for user safety and to prevent the users properties from being damaged. Read the
following safety instructions carefully before using the pump it up.
ANDAMIRO takes no responsibility for any damages and troubles caused by the users mistakes.
Inspection and cleaning Moving and transportation
Be sure to turn OFF the main power switch The game machine contains parts such as
and unplug the power cord from the the monitor, electronic components and ■ Use only a grounded outlet.
receptacle before inspecting or cleaning the precision components which are sensitive to ■ Do not extend the power cord for use.
machine. vibrations and impacts. Great care therefore
• Failure to do so could result in electrical shock. should be taken when moving and ■ Check the power requirements for the place to install the product.
transporting the game machine.
When replacing parts, be sure to use parts of Be sure not to let the machine tip over. ■ Use the power cord matching with power requirements.
the correct specifications. Never use parts
other than the specified ones.
■ Use the rating fuse.
Before moving the machine, be sure to turn
• Using improper parts could result in fire or OFF the main power switch, unplug the ■ Do not touch the power plug with wet hands.
equipment failure. power cord form the receptacle and remove
the power cord form the machine.
■ Power off the product when installing the product.
There is high voltage inside the machine. • Stepping on or tripping over the power cord
Only qualified industry specialist is allowed may result in an accident or damage to the machine.
to open the machine's back door. With the back door
open, be very careful not to touch the monitor and its Before moving the machine, be sure to fully lift the
nearby parts. four levelers and move it on the casters.
• Otherwise an accident or electric shock may result.
6 7
Testing and Setting the PUMP I / O Test
Set and test the product before using it. The I/O Test lets you test the pad sensors and the lamps, buttons located on the body of product.
2 Press the "Service" button ( ) and the I/O Test items will appear on the screen.
SETUP MENU
I/O TEST
I/O TEST
EEPROM TEST 1. TEST BUTTON : OFF
SCREEN TEST 2. SERVICE BUTTON : OFF
GAME OPTION 3. CLEAR BUTTON : OFF
COIN OPTION 4. COIN1 : OFF
SOUND TEST 5. COIN2 : OFF
BOOKKEEPING
STATISTICS
EXIT EXIT - SERVICE BUTTON
Lock OK:0 Err:0
■Pad Test : Each pad includes four sensors. Check the sensors properly operate.
If every sensor is okay when you stand on a pad or pads, the pads shown
on the screen yellow light.
▶ Checking the version information ■Lamp Test : Check whether the halogen lamps (yellow, red) on the top of body
The program version information is displayed on the top and to the left of title screen and the neon lamp (blue) located on the bottom of body (speaker) flicker
and the bottom and to the left of initial screen. in regular sequence.
■Button Test : Check whether the Test, Service, Clear button and coin controller operate
normally. (If all lamps operate normally, their colors will be changed into red
and flicker.)
2 Setting the menu ※ If nothing normal happens, contact your service center for inspection or repair.
"Service" Button (
I/O TEST -> EEPROM TEST -> .. -> SOUND TEST -> EXIT
2 Press the "Service" button ( )and the EEPROM TEST items will appear on the screen.
When the letters and numbers for WRITE are identical with ones for READ, the result message "Success" 2
Press the "Service" button (
screen.
) and the pattern as shown on the right will appear on the
will appear. But when the letters and numbers for WRITE are different from ones for READ, the result Check whether the color and linearity of latticed pattern are normal.
message "Fail" will appear.
EEPROM TEST
SCREEN TEST
WRITE •••••• ABCDEFGHIJKLMNOPQRSTUVWXYZ123456789
READ •••••• ABCDEFGHIJKLMNOPQRSTUVWXYZ123456789
RESULT •••••• SUCCESS
※ If nothing normal happens, contact your service center for inspection or repair.
※ If nothing normal happens, contact your service center for inspection or repair.
10 11
Game Option
The Game Option lets the user set the degree of difficulty of game and stage option.
2 Press the "Service" button ( ) and the Game Option items will appear on the screen.
Available settings: OFF/Stages 1~4
d. LANGUAGE
e. DEMO SOUND
a . GAME MODE
Select“N o r m a l”or“E v e n t”.
b. LEVEL
Set the degree of difficulty of game.
The degree of difficulty is set in three steps, including Easy/Normal/Hard.
12 13
Coin Option SOUND TEST
You can change the coin related settings. The Sound Test lets you test music tracks and effect sound.
Press the "Service" button ( ) and the Sound Test items will appear on the screen.
2 Press the "Service" button ( ) and the Coin Option items will appear on the screen.
2
COIN OPTION
COIN1 SETTING 1 CREDIT / 5 COINS
COIN2 SETTING 4 CREDIT / 1 COINS SOUND TEST
DEFAULT SETTING
SAVE AND EXIT AUDIO #00
EXIT EFFECT SOUND #00
EXIT
MOVE - TEST BUTTON
SELECT - SERVICE BUTTON MOVE - TEST BUTTON
SELECT - SERVICE BUTTON
14 15
BOOKKEEPING MENU STATISTICS MENU
Check the input of coins and the number of services. It indicates the number of the play.
Press the "Service" button ( ) and the Bookkeeping items will appear on the screen. Press the "Service" button ( ) and the Statistics items will appear on the screen.
2 2
16 17
CONTENS How to Install the Pump
Mechanical Drawing
Main Case
18 19
2 Connect all connectors. 3 Fasten all screws.
Bill-Board
Main Case
Main Case
20 21
4 Use brackets and fasten all screws to joint the left and right floor controllers. 5 External view of the Pump
RED
745(SX)
Bottom Left 1,100 300~500 770(GX)
16-M6XL20
Bottom Right
8-M6XL20
1,110
1,780
22 23
Mechanical Drawing
6 Connect the connector cables between the floor controller and main ass’
y. 1
8-M6XL20
RED(1P)
24 25
2 3
26 27
4 5
28 29
6 7
30 31
8 9
POWER ASS’Y
CD-ROM
32 33
9-1 10
FLW
SERVICE TEST
WOOF
MASTER
COIN COUNTER
34 35
Outward Shape of PUMP IT UP FAQ and Solutions
10
◇ There is no sound or the visual.
1. Check the switch below the right side of MAIN CABINET.
2. Check the lighting of LED pushing the play button of CD-ROM in main box.
3. In case LED does not turn on, the CD-ROM has to be replaced because the
problem comes from the CD-ROM.
4. In case LED turns on well, the main box has to be replaced because the problem
comes from the main box.
36 37
FAQ and Solutions PUMP IT UP, BLOCK DIAGRAM
AC 110~220V
CRT BOARD
JAMMA PCB
◇ 1P and 2P of step sensor do not work well.
MONITOR(CRT) MAIN BOX
1. Check the problem whether it comes from the electric connection or the FOOT
29”(SX)
PCB through exchanging the wire of 1P and 2P. 33”(GX) MK-5 BOARD
AMP BOX
◇ Step-lamp does not work.
LAMP PCB TEST S/W SERVICE S/W
1. Test it exchanging with the normal operating lamp. (Check whether the problem SMPS
COUNTER FLW VOLUME
comes from the lamp or inverter) DC 12~14.5V AMP PCB
2. Replace the defected one after test. MASTER VOLUME WOOFER VOLUME
HALOGEN LAMP “R” NEON LAMP FOOT SENSOR “1P” FOOT SENSOR “2P”
◇ When the games is in process, the music and the arrows do not match.
LAMP ASS’Y
1. Cleane the CD-ROM. INVERTER “1P” INVERTER “2P”
2. Replace the CD-ROM.
CCFL LAMP “1P” CCFL LAMP “2P”
FLW SPEAKER “L” FLW SPEAKER “R”
FOOT ASS’Y
WOOFER SPEAKER WOOFER SPEAKER
SPEAKER ASS’Y
AC VOLT
DC VOLT
CONTROL PANEL (PRE AMP ASS’Y)
포스트스크립트 그림
(\276\310\264\331\271\314\267\316\267\316\260\355-\307\245\301\366)
SIGNAL
38 39
Pump it up hidden mode information Specifications
Screen Size 2 9" 3 3"
40 41
PUMP IT UP PROBLEMS
PA RTS DESCRIPTION R E P O RTED PROBLEMS CHECK POINT CHECK NEXT
FUSE BOX CHECK FUSE,POWER S/W AND AC VOLTAGE (110~220V) AC CORD, AC VOLTAGE
AC POWER NOISE FILTER NO POWER ON GAME MACHINE (NO LIGHT ON AC LAMP,NO MOVE) CHECK AC VOLTAGE INPUT AND OUTPUT (110~220V) FUSE BOX
TRANSFORMER CHECK AC VOLTAGE INPUT AND OUTPUT (110~220V) NOISE FILTER
TEST BUTTON
80 CHECK TEST /SERVICE BUTTON AND WIRE
SERVICE BUTTON
MAIN PCB
COUNTER COUNTER WILL NOT REGISTER(COIN, PRIZE, TICKET) CHECK DC 12V INPUT
CONTROL PANEL
(TEST BRACKET) MASTER VOLUME
FLVV VOLUME INOPERATIVE SOUND VOLUME CONTROL(PRE AMP ERROR) CHECK VOLUME REGISTER (CHECK PRE-AMP)
PRE AMP
WOOFER VOLUME
ELECTRONIC BALLAST TRANSFORMER
AC LAMP ERROR (NO LIGHT ON AC LAMP) CHECK POWER AC VOLTAGE INPUT AND AC LAMP
AC PART AC LAMP ELECTRONIC BALLAST
AC FAN(LEFT, RIGHT) AC FAN ERROR (NO POWER ON AC FAN) CHECK POWER AC VOLTAGE INPUT
ATX POWER DC 12V, 5V MAIN BOX ASS’Y ERROR CHECK POWER AC VOLTAGE TRANSFORMER
POWER BOX ASS’Y FOOT ASS’Y ERROR
SMPS DC 12V CHECK OUTPUT DC 12V
LAMP PCB IN AMP BOX ASS’Y ERROR
MAIN BOX ASS’Y I/O ERROR
JAMMA PCB CHECK POWER AC VOLTAGE (ALL PCB ERROR)
I/O ERROR
BACKGROUND NOISE ON AUDIO CHECK CD-DISC AND WIRE CONNECTIONS
FOOT ASS’Y ERROR CHECK STEP I/O AND WIRE CONNECTIONS(REPLACE ACTEL CHIP)
CONTROL PANEL ERROR CHECK CONTROL PANEL AND WIRE CONNECTIONS
ALL LAMP ERROR CHECK ALL HALOGEN AND NEON LAMPS
SOUND BOARD (MAIN) CHECK DC 12V INPUT
COUNTER WILL NOT REGISTER (COIN, PRIZE, TICKET)
COIN MACHINE ERROR CHECK COIN MACHINE AND WIRE CONNECTIONS
NO VIDEO (BLUE SCREEN) CHECK VGA AND WIRE CONNECTION POWER BOX (ATX POWER)
MAIN BOX ASS’Y
GAME AND DEMO PLAY FROZEN OR FREEZING UP
CHECK POWER DC VOLTAGE AND MK-5(CHECK POWER BOX)
MK-5BOARD GAME FROZEN OR FREEZING UP
SCREEN NOISE OR VIDEO INTERFERENCE CHECK VGA CHIP AND WIRE CONNECTION
GAME FROZEN OR FREEZING UP
CD ROM DRIVE MUSIC AND FOOT STEP MOVEMENT DOES NOT SYNCH OR MATCH
CHECK POWER DC VOLTAGE, CD-ROM DRIVE AND DISC
SOUND AND VIDEO GRAPHIC ERROR
SLOW SELECTING ERROR
CD-DISC GAME AND DEMO PLAY FROZEN OR FREEZING UP
LOCK CHIP ERROR (CD-DISC AND LOCK CHIP MISMATCH) CHECK FOR DISC SCRATCH AND VERSION
SOUND AND GRAHPIC ERROR
LOCK CHIP LOCK CHIP ERROR CHECK LOCK CHIP VERSION AND DC VOLTAGE
PUMP IT UP PROBLEMS
PA RTS DESCRIPTION R E P O RTED PROBLEMS CHECK POINT CHECK NEXT
LAMP PCB ALL LAMP ERROR OR ALL LAMPS DOWN CHECK DC 12V INPUT AND LAMPS POWER BOX(SMPS POWER)
NO SOUND OR AUDIO
AMP BOX ASS’Y AMP PCB ERROR ON UPPER LEFT AND RIGHT SPEAKERS (FLW)
CHECK DC 15V INPUT AND AMP PCB SMPS DC 15V
ERROR ON LOWER LEFT AND RIGHT SPEAKERS (WOOFER)
ERROR ON PRE AMP POWER (OUTPUT DC 15V)
SMPS DC 15V NO POWER AMP PCB PRE AMP PCB (OUTPUT DC 15V) CHECK AC VOLTAGE INPUT AND DC 15V OUTPUT TRANSFORMER
FOOT SENSOR ERROR
FOOT PCB CHECK DC 12V INPUT AND ACTEL CHIP IF NOT, REPLACE MAIN BOX (SOUND PCB)
INVERTER ERROR
42