Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Connections
Pin Number 1 2 3 4 5 6
DESIGNATION
FUNCTION
Chassis ground RS 232 Transmission RS 232 Reception RS 422/485 Transmission RS 422/485 Transmission RS 422/485 Reception RS 232/RS 422 Common Common for multipoint address and Adjust (pins 12, 14-l 7, 24) Isolated current loop reception Isolated current loop reception Reserved Reserved Reserved Terminal address in multipoint mode (binary 1) Terminal address in multipoint mode (binary 2) Terminal address in multipoint mode (binary 4) Terminal address in multipoint mode (binary 8) RS 422J485 Reception Reserved Isolated current loop transmission Isolated current loop transmission Reserved Reserved Multipoint address parity Reserved
0
10 20 30 40
50
014
7 8 9 10 11 12 13 14
015
016
017
Q9
60
70
OW
QO 021
80
90
15 16 17 18 19 20
100
110 120
Q2 023 024
130
025
21 22 23 24 25
PAR
Connections
Serial Link and Supply Connector Pin Arrangement
+ _ El
Power Supply 24V ov
G c
4-
Chassis ground
Connections
8.2
Connecting
The connection between the CRT terminal and the XBT-A uses a 2.50 meter XBT Z 905 cable connected to the LINE input to the CRT terminal and to the Serial port of the XBT-A terminal. The transmission parameters must be set first. To change the settings on the XBT-A terminal, refer to sub-section 4.5: Configuration, page 24.
The connection between the TSX T407 programming terminal and the XBT-A uses a 2.50 meter XBT Z 905 cable. - connected to the Printer port on the TSX T407, - connected to the Serial port on the XBT-A, - connect the XBT Z 905 cable with the end showing the reference number to the XBT-A.
Connections
Connecting a CRT or TSX T407 Terminal
pin arrangement:
----_
XBT-A
I
A
TRANSMISSION
I I I I I I I I I I I I
cl
2
cl
3
I I r-l
-L TXD
L.--L
TRANSMISSION
RECEPTION
cl
r-l
RXD
RECEPTION
E
4 5
lid
Connections
PUPS Serial port Connector g-pin male 25.pin male 25-pin female products available since July 1988 Ref. No. XBTZ915 XBTZ905 XBTZ9052
Connections
Connecting a PUPS Microcomputer
XBTZ915
I
I
I
I
TRANSMISSION
I I
I I
q
2
RECEPTION
RECEPTION
I I I I I
I I I I 8
TRANSMISSION
FITS r-l
q
XBTZ905 and XBTZ9052 cable pin arrangement:
CTS
DSR cl
--XBT-A --
---_
t 2.5pin serial port
TRANSMISSION
TRANSMISSION
RECEPTION
RECEPTION
u
n DSR L-l DTR cl
Connections
Note: RS 485 is an extension of the RS 422 standard ( 4-wire differential transmission) that loops the transmitter back to the receiver in the XBT-A.
Distance (m) I
1OM
SPEED (BAUD)
Programming Port
Connections
Connecting a TSX17-20 Micro-PLC
-----
r---------
TSX 17-20
(PROGRAMMING PORT)
00 00
00 00 OO 00 00 00 00 00
00
0
go
R
!
0 <
0 0 00 00 00 00 00 00 00
(I
12 ------------J
oI
Connections
The supply for the current loop is provided by the TSX 27/47 (ACTIVE). Current limiting is ensured by the XBT-A (PASSIVE PROTECTED). Note: the programming port of TSX 27 and TSX 47100 PLCs is not isolated. When using these PLCs, when the distance between the XBT-A and the TSX 27/47 is more than 3 meters, a XBT Z 9011/l 2 isolating device must be used between the two units (further details on the XBT Z 90.. in this section).
Distance+ (m)
1 OOOm
loom 15m
(BAUD)
XBT-A
TSX 7
Connections
Connecting TSX 27/47 PLCs
------__
XBT-A
r_____-___--___
iission
-----__-----__J
8 , ----cl I
I
I
ov
ti
12
5-IL
L___________-___
Connections
Connecting TSX 27147 PLCs
If the distance betweeh the XBT-A terminal and the PLC is more than 3 meters, the XBT Z 901 l/12 isolating device should be used. The distance between the PLC and the XBT Z 90.. must be less than 5 meters (connected by two shielded twisted pairs of not less that 0.6 mm2 (AWG 22) gauge). The distance between the XBT Z 901 l/12 and the XBT-A terminal can be as much as 1000 meters (connected by two shielded twisted pairs of not less that 0.6 mm2 (AWG 22) gauge).
131
Connections
Connecting TSX 27/47 PLCs
TOP VIEW
XBT-A 2 1000 m.
TSX 47
Transmission I-I\
:
L-_-_---1
Mechanical characteristics:
- XBT
Z9011: symetrical rail mount Dimensions: Length Width Depth :96mm :27mm :42mm
Connections
The power supply to the current loop is provided by the module (ACTIVE). The XBT-A ensures current limiting (PASSIVE PROTECTED). The maximum data link distance is 1000 meters (connected by two shielded twisted pairs of not less that 0.6 mm*(AWG 22) gauge). When used with TSX Series 7 PLCs, the XBT-A connects to the TSX SCM 20.. module via a 2.5 meter XBT Z 906 cable.
Distance
120mA
CURRENT!
Cm)
I-
XBT Z 906
Connections
Connecting a Serial Communication Module
--XBT- A
Reception
+ a
--1 I 9
10
TransmI-,,:
Transmission ____ Lz-.
,oop
SUPPlY) 1 II
- --
c___--_-____-__-
Connections
Connecting a Serial Communication Module
RS 232 C connection:
The transmission parameters must be set. To do this, refer to sub-section 4.5.2, Configuration, page 26. The maximum data link distance is 15 meters and connection via by two shielded twisted pairs of not less that 0.6 mm2 (AWG 22) gauge). When used with TSX Series 7 PLCs, the XBT-A connects to the TSX SCM 20.. module via a 2.5 meter XBT Z 905 cable.
Distance
(m) t
1 OOm
15m
10K
1OO K
SPEED (BAUD)
XBT-A
TSX47i67/07
1
XBT 2 905
125
Connections
Connecting a Serial Communication Module
XBT-A
A
c-----i I I I I I I I I I I I I
157
c
_L RTS r-l CTS
0 r-h
RECEPTION
RXD
i?-
cl
I O I
-
Connections
Connecting a Serial Communication Module
RS 422 connection:
This standard defines a differential transmission mode. This 4-wire data link enables operation in Full Duplex mode.
Distance (m)
10 M Baud
Connect via by two shielded twisted pairs of not less that 0.6 mm (AWG gauge).
22)
137
Connections
Connecting a Serial Communication Module
Connection example with a TSX Series 7 PLC (and SCM 20 Serial Communication Module). ---XBT-A r-5 A
TRANSMISSION
Note: RS 485 operation is an extension of the RS 422 standard. It loops the transmitter back to the receiver on each device (connect +TD to + RD and -TD to -RD). This 2-wire data link requires Half Duplex operation.
Connections
Serial multipoint XBT-A terminals operate in ASCII, PROTECTED PASSING CURRENT LOOP MODE. The line power supply is provided by an external source or by the Serial Communication Module (ACTIVE).
All XBT-A terminals must be connected in series. Current limiting is ensured by XBT-A terminals (PASSIVE PROTECTED). XBT-A terminals must be addressed (coded) by wiring in the serial connector. Refer to sub-section 6.8, Multipoint Operation, page 96.
13Q
Connections
Multipoint Connection
Connection example for a TSX Series 7 PLC and an SCM 20 module. --------XBT- A
Reception
I I I I 20
I I
Reef
Transmission
9
1 Reception 20 I 21 -. -10 I___-_
-------
-__
I I ---------I
XBT- A
Reception
inn
Connections
Multipoint Connection
. Multipoint parallel XBT-A TERMINALS CURRENT LOOP OPERATE IN ASCII MODE WITH BLOCKED
The line power supply is provided by an external source or by the Serial Communication Module (ACTIVE). All XBT-A terminals must be connected in parallel. XBT-A terminals must be addressed (coded) by wiring in the serial connector. Refer to sub-section 6.8, Multipoint Operation, page 96. Connection example for a TSX Series 7 PLC and an SCM 20 module:
-XBT- A
--
1 n
k-Transmission
__---_---XBT- A ov
7 +-t-I
Q-----h
11 Reception fw
l-___--_------__
Connections
Multipoint Connection
. Multipoint parallel XBT-A TERMINALS OPERATE IN ASCII RS 422 MODE - All Slave receive lines are wired in parallel to the Master transmission line. - All Slave transmit lines are wired in parallel to the Master reception line.The number of Slave stations is restricted to 10. XBT-A terminals must be addressed (coded) by wiring in the serial connector. Refer to sub-section, 6.8 Multipoint Operation, page 96.
--XBT-A
BLOCK DIAGRAM A 9
--__
-RD
-7
t
TRANSMISSION RECEPTION OTHER TERMINALS
Connections
Multipoint Connection
The length of passive drops must not exceed 10 meters. The total line length must not exceed 1200 meters. To install this type of data link, line adapters may be required. For further information refer to the TSX SCM Installation Manual (Ref. No. TSX D43 724).
Note: RS 485 operation is possible by looping the receiver back to the transmitter (connect + TD to + RD and - TD to - RD) on all XBT-A terminals and on the 2-wire master logic. All devices connected in RS 485 mode must operate in Half Duplex mode. Address coding limits the number of devices to a maximum of 15.
Connections
, TEST PLUGS
R=56Q1/2W