Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
ECAM 23.450 (EX3) - Test Modeservice Manual
ECAM 23.450 (EX3) - Test Modeservice Manual
Motore Macinino
Discharge valve 3 ways
Motore Gruppo infusore
Infuser Group motor
Grinder Motor
Pump Thermal protector
Protettore Pompa
Scheda comandi
Control board
Resistenza Caffè
Coffee Heating element
Resistenza Vapore
Steam Heating element
Elettrovalvola scarico 3 vie
Bianco / White
Blu / Blue
Giallo / Yellow
Grigio / Grey
Marrone / Brown
Nero / Black
Rosso / Red
Verde / Green
Viola / Violet
CORRISPONDENZA
TEST PROCEDURA NOTE
TASTO CARICO
Con macchina spenta (interruttore generale in
EV1+EV2
posizione 0) ma collegata alla rete elettrica, premere
contemporaneamente i tasti sottostanti e
HEATER
successivamente portare l'interruttore generale in
posizione I: CORRESPONDENCE BETWEEN
TE S T P R OC E DUR E GRINDER
BUTTON PRESSED - ICON / LOAD
Button- Icon LOAD
EV1
LOAD TEST i microswitch emettono il segnale
OK Water Pump
MODE MOTOR acustico quando attivati
UP/DOWN
Infuser motor
MENU
PUMP UP
NOTA: Rilasciare i tasti quando il motore inizia la
With the machine in Standby mode, EV2
movimentazione 1 CUP Coffee boiler ON
(OFF with main switch on 1), open
Service door, then press and hold VAPORIZER
symultaneously the 3 icons: )
ON / STANDBY Steam boiler ON
CORRISPONDENZA
TEST L OAD T E S T
PROCEDURA
Menu, 1 CUP, “Coffee” Taste, till the NOTE
TASTO DISPLAY
MODE message displayed is:
Con macchina spenta (interruttore generale in
“SELECT TEST”. HOT WATER1
BUTTON EV 2
posizione 0) ma collegata alla rete elettrica, premere
Close the door and press
contemporaneamente i tasti sottostanti e
“COFFEE LENGHT” BUTTON 2
successivamente portare l'interruttore generale in 2 CUPS
to enTer the test procedure EV 1 + Fan
posizione I:
(message displayed: BUTTON 3
“LOAD TEST MODE”). EV 1 + EV 2
CAPPUCCINO
BUTTON 4 + Light
DISPLAY BUTTON 5
TASTE Grinder Motor
L'accesso al display test mode abilita il
TEST
BUTTON 6 primo innesco
MODE
Infuser motor
COFFEE LENGHT
BUTTON 7 DOWN
BUTTON 8
MANOPOLA Incremento della
GUSTO barra di progresso
NOTA:
To exitRilasciare i tasti quando appare
the procedure, unplug il messaggio
the machine or switch it OFF by the main switch.
DISPLAY TEST MODE
CORRISPONDENCE
TEST PROCEDURE NOTE
BUTTON LOAD
Machine OFF but plugged IN. Press and hold
EV1+EV2
simultaneously the following buttons, then
switch the main switch on position I:
HEATER
CORRESPONDENCE BETWEEN
TE S T P R OC E DUR E GRINDER
BUTTON PRESSED - ICON / LOAD
Button- Icon LOAD
EV1
LOAD TEST
OK Water Pump
MODE MOTOR
UP/DOWN
Infuser motor
MENU
PUMP UP
NOTE: Release the buttons after the motor
With the machine in Standby mode, EV2
starts to move 1 CUP Coffee boiler ON
(OFF with main switch on 1), open
Service door, then press and hold VAPORIZER
symultaneously the 3 icons: )
ON / STANDBY Steam boiler ON
CORRISPONDENCE
TEST L OAD T E S T
PROCEDURE
Menu, 1 CUP, “Coffee” Taste, till the NOTE
BUTTON DISPLAY
MODE message displayed is:
“SELECT
Machine OFF but plugged TEST”.
IN. Press and hold HOT WATER1
BUTTON EV 2
Close the
simultaneously the following doorthen
buttons, and press
“COFFEE
switch the main switch LENGHT”
on position I: BUTTON 2
to enTer the test procedure 2 CUPS EV 1 + Fan
(message displayed: BUTTON 3
“LOAD TEST MODE”). EV 1 + EV 2
CAPPUCCINO
BUTTON 4 + Light
DISPLAY BUTTON 5
TASTE Entering
Grinder this Procedure will enable
Motor
TEST the priming of the pump
MODE BUTTON 6
Infuser motor
COFFEE LENGHT
BUTTON 7 DOWN
BUTTON 8
Turn Coffee LED bar will lit
taste knob
NOTE: Release the buttons after the message
To exit the procedure,
“DISPLAY unplug
TEST MODE” the machine or switch it OFF by the main switch.
is displayed