Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
KH4407 DESTRUCTORA AUTOMTICA Instrucciones de uso DISTRUGGIDOCUMENTI AUTOMATICO Istruzioni per l'uso AUTOMATIC SHREDDER Operating instructions KOMPERNASS GMBH BURGSTRASSE 21 D-44867 BOCHUM www.kompernass.com ID-Nr.: KH4407-01/09-V2 AUTOMATISCHER AKTENVERNICHTER Bedienungsanleitung
KH 4407
NDICE
Uso conforme al previsto Indicaciones de seguridad importantes Caractersticas tcnicas Volumen de suministro Descripcin de aparatos Puesta en funcionamiento Manejo Vaciar el cubo de recogida Limpieza Evacuacin Garanta y servicio Importador En caso de avera
PGINA
2 2 3 3 3 3 3 4 5 5 5 5 6
Guardar estas instrucciones para preguntas posteriores e, igualmente entregar stas, en caso de dar el aparato a terceras personas!
-1-
-2-
Volumen de suministro
Destructora de documentos KH 4407 Instrucciones de uso
Descripcin de aparatos
q Cubierta de corte w Interruptor e Abertura de corte para CDs/tarjetas de crdito r Abertura de corte para papel t Cubo de recogida grande (papel) y Cable de alimentacin u Cubo de recogida pequeo (transparente) /
ventanilla
Puesta en funcionamiento
En primer lugar, coloque la cubierta de corte q sobre el cubo de recogida grande t, de forma que el cable de red y quede detrs, en el lado cerrado. Deslice el cubo de recogida pequeo u para plstico hacia la abertura de la parte delantera del cubo de recogida grande t. Conecte la destructora de documentos a una base de enchufe.
Caractersticas tcnicas
Tensin de red: Corriente nominal: Potencia nominal: Clase de proteccin: Proceso de corte para papel: 4x18 mmAnchura de trabajo: Tiempo servicio continuo: 220-240 V ~ 50Hz 1,8 A 380 W II corte en cruz, partculas 223 mm 3 minutos
Manejo
Encender el aparato: Coloque el interruptor w de trituracin a la posicin . Introducir papel: Introduzca el papel de forma vertical, desde arriba, en la abertura de corte para papel r. El motor se enciende automticamente y se vuelve a apagar si no se introduce ms papel. Puede 2 cortar hasta 7 hojas (80g/m papel) al mismo tiempo.
-3-
Periodo KB Con el periodo KB (funcionamiento por un corto periodo de tiempo) se indica durante cunto tiempo puede funcionar un aparato sin que el motor se sobrecaliente ni se dae. Tras el periodo KB indicado deber apagarse el aparato hasta que el motor se haya enfriado.
Introducir una tarjeta de crdito: Abra la cubierta de seguridad sobre la abertura de corte para CDs/tarjetas de crdito e. Introduzca la tarjeta de crdito desde arriba en el centro en la abertura de corte para CDs/tarjetas de crdito e. Slo se puede cortar una tarjeta de crdito cada vez. Introdzcala siempre con la parte ancha hacia delante en la abertura de corte para CDs/tarjetas de crdito e. De lo contrario no se destruirn las bandas magnticas. Indicacin: Introduzca la tarjeta de crdito siempre en el centro de la abertura de corte para CDs/tarjetas de crdito e. De lo contrario el proceso de corte no comenzar! Introducir un CD: Introduzca el CD en el centro, desde arriba, en la abertura de corte para CDs/tarjetas de crdito e. Slo se puede cortar un CD cada vez. Advertencia: No introducir los dedos en la abertura central para CDs, al introducir los CDs en el aparato. Eliminar un atasco de material: Deslice el interruptor w a la posicin , si se atasca el objeto a cortar. La marcha se enciende y el material que est cortando puede retirarse de nuevo. Coloque el interruptor w en la posicin (OFF), en cuanto el objeto a cortar se libere. Apagar el aparato: Para apagar el aparato, coloque el interruptor w en la posicin central (OFF).
-4-
Limpieza
Peligro! Antes de la limpieza extraiga la clavija de red. Existe riesgo de descarga elctrica! Advertencia! Las cuchillas de corte del aparato estn muy afiladas! Peligro de lesiones! Vace el cubo de recogida t/u de forma regular. Limpie el cubo de recogida t/u y la cubierta de corte q con un pao ligeramente humedecido y, en caso necesario, con un detergente suave. Retire los posibles restos de las aberturas de corte e/r con un objeto apropiado. Asegrese al hacerlo de que la clavija de red est desconectada.
Garanta y servicio
Con este aparato recibe usted 3 aos de garanta desde la fecha de compra. El aparato ha sido fabricado cuidadosamente y ha sido probado antes de su entrega. Guarde el comprobante de caja como justificante de compra. Si necesitara hacer uso de la garanta, pngase en contacto por telfono con su punto de servicio habitual. ste es el nico modo de garantizar un envo gratuito. La garanta cubre los defectos de fabricacin o del material, pero no las piezas sujetas a desgaste y los daos sufridos por las piezas frgiles. Este producto ha sido diseado exclusivamente para el uso particular y no para el uso industrial. En caso de manipulacin indebida e incorrecta, uso de la fuerza y en caso de abrir el aparato personas extraas a nuestros centros de asistencia tcnica autorizados, la garanta pierde su validez. Esta garanta no reduce en forma alguna sus derechos legales. Kompernass Service Espaa Tel.: 902/884663 e-mail: support.es@kompernass.com
Evacuacin
En ningn caso deber tirar el aparato a la basura domstica. Este producto est sometido a la directiva europea 2002/96/EC. Elimine el aparato a travs de una empresa de evacuacin de basuras autorizada o por medio del centro de evacuacin de basuras municipal. Tenga en cuenta las normativas actuales en vigor. En caso de duda pngase en contacto con el centro de evacuacin de basuras. El material de embalaje debe desecharse de forma respetuosa con el medio ambiente.
Importador
KOMPERNASS GMBH BURGSTRASSE 21 44867 BOCHUM, GERMANY www.kompernass.com
-5-
En caso de avera
Si el material que se corta se queda atrapado en el aparato: Ello significa que se ha introducido demasiado material en el aparato (mx. 7 hojas de papel de 80g/m2, mx. 1 tarjeta de crdito, mx. 1 CD/DVD). Deslice el interruptor wa la posicin , si se atasca el objeto a cortar. La marcha se enciende y el material que est cortando puede retirarse de nuevo. Coloque el interruptor wen la posicin (OFF), en cuanto el objeto a cortar se libere. Si el aparato se para de repente: Esto significa que el aparato se ha sobrecalentado y la desconexin de seguridad automtica se ha activado. Atencin: Extraiga la clavija de red de la base de enchufe, para evitar una conexin no intencionada. Para apagar el aparato, coloque el interruptor w en la posicin central (OFF). Deje que el aparato se enfre. Vuelva a introducir la clavija de red en la base de enchufe. Para encender el aparato, coloque el interruptor wen la posicin .
Si no se puede encender el aparato: Compruebe si la clavija de red se encuentra conectada a la base de enchufe. Pruebe otra base de enchufe. El aparato puede estar defectuoso. Haga revisar el aparato por personal especializado. Si no comienza el proceso de corte pese a que el aparato est encendido: El aparato se ha sobrecalentado y se ha activado la desconexin de seguridad automtica. Atencin: Extraiga la clavija de red de la base de enchufe para evitar una conexin no intencionada. Para apagar el aparato, coloque el interruptor w en la posicin central (OFF). Deje que el aparato se enfre. Vuelva a introducir la clavija de red en la base de enchufe. Para encender el aparato, coloque el interruptor wen la posicin . La cubierta de corte qno est bien puesta. Coloque correctamente la cubierta de corte q.
-6-
INDICE
Uso conforme Importanti avvertenze di sicurezza Dati tecnici Fornitura Descrizione dell'appa-recchio Messa in funzione Utilizzo Svuotamento del contenitore di raccolta Pulizia Smaltimento Garanzia & assistenza Importatore In caso di guasti
PAGINA
8 8 9 9 9 9 9 10 11 11 11 11 12
Conservare le presenti istruzioni per consultarle in futuro; in caso di cessione dell'apparecchio a terzi, consegnare anche le istruzioni!
-7-
DISTRUGGIDOCUMENTI KH 4407
Uso conforme
Il distruggidocumenti idoneo esclusivamente alla triturazione di carta, carte di credito e CD. Qualunque altro impiego o modifica dell'apparecchio da considerarsi non conforme alla destinazione e comporta gravi rischi di infortunio.
-8-
Fornitura
Distruggidocumenti KH 4407 Istruzioni per l'uso
Descrizione dell'appa-recchio
q Dispositivo di taglio w Interruttore e Apertura di taglio CD/carta di credito r Apertura di taglio carta t Contenitore di raccolta pi grande (carta) y Cavo di rete u Contenitore di raccolta pi piccolo (trasparente)
/ obl
Messa in funzione
Posizionare prima il dispositivo di taglio q sul contenitore di raccolta grande t, in modo che il cavo di rete y si trovi sul retro, sul lato chiuso. Spingere il contenitore di raccolta piccolo u per la plastica nell'apertura sul lato anteriore del contenitore di raccolta grande t. Collegare il distruggidocumenti a una presa di corrente.
Dati tecnici
Tensione di rete: Corrente nominale: Potenza nominale: Classe di protezione: Procedimento di taglio per carta: 220-240 V ~ 50Hz 1,8 A 380 W II taglio incrociato, particelle da 4x18 mm 223 mm
Utilizzo
Accensione dell'apparecchio: Spingere l'interruttore w per la triturazione in posizione . Inserimento della carta: inserire la carta verticalmente dall'alto nell'apertura di taglio per la carta r .
Tempo di funzionamento abbreviato Il tempo di funzionamento abbreviato indica il tempo di funzionamento dell'apparecchio senza pericolo di surriscaldamento e di guasti al motore. In base al tempo di funzionamento abbreviato, l'apparecchio dev'essere spento fino al completo raffreddamento del motore.
-9-
Il motore si avvia automaticamente e si arresta automaticamente non appena si interrompe l'inserimento della carta. Si possono tagliare fino a 7 fogli (carta da 80g/m2) contemporaneamente. Inserimento della carta di credito: aprire lo sportello di sicurezza sull'apertura di taglio per CD/carte di credito e. Inserire la carta di credito dall'alto al centro nell' apertura di taglio per CD/carte di credito e. possibile inserire solo una carta di credito per volta. Guidare sempre le carte di credito partendo dal lato pi largo nell'apertura di taglio per CD/ carte di credito e . In caso contrario, la striscia magnetica non verr distrutta. Avvertenza: inserire la carta di credito sempre al centro nell'apertura di taglio per CD/carte di credito e . In caso contrario, il procedimento di taglio non verr avviato! Inserimento del CD: Inserire il CD dall'alto al centro nell'apertura di taglio per CD/carte di credito e. possibile inserire solo un CD per volta. Avvertenza: non infilare le dita nel foro centrale del CD mentre lo si sta inserendo nell' apparecchio. In caso di blocco del materiale: Spingere l'interruttore w in posizione , qualora il materiale da tagliare sia rimasto incastrato. In tal modo viene azionata la retromarcia e il materiale da tagliare viene fatto fuoriuscire nuovamente. Impostare l'interruttore w in posizione (OFF), non appena ottenuta la fuoriuscita del materiale da tagliare.
- 10 -
Svuotare il contenitore di raccolta t/u. Fare raffreddare l'apparecchio. Reinserire la spina nella presa. Accendere l'apparecchio spostando l'interruttore w in posizione .
Pulizia
Pericolo! Staccare la spina dalla presa di corrente prima di ogni pulizia. Ci comporterebbe il rischio di scossa elettrica! Avviso! I coltelli di taglio dell'apparecchio sono molto affilati! Pericolo di lesioni! Svuotare il contenitore di raccolta t/u regolarmente. Pulire il contenitore di raccolta t/u e il dispositivo di taglio q con un panno leggermente inumidito ed eventualmente con un detergente delicato. Rimuovere eventuali resti nelle aperture di taglio e/r con un oggetto adatto. Accertarsi di aver staccato la spina dalla presa.
Importatore
KOMPERNASS GMBH BURGSTRASSE 21 44867 BOCHUM, GERMANY www.kompernass.com
Smaltimento
Non gettare per alcun motivo lapparecchio insieme ai normali rifiuti domestici. Questo prodotto sottost alla direttiva europea 2002/96/EC. Smaltire lapparecchio presso unazienda autorizzata o presso lente comunale di smaltimento. Rispettare le norme attualmente in vigore. In caso di dubbi, contattare lazienda di smaltimento competente. Smaltire tutti i materiali dimballo in conformit alle norme per il rispetto dellambiente.
- 11 -
In caso di guasti
Se il materiale da tagliare resta incastrato nell'apparecchio: significa che stata inserita una quantit eccessiva di materiale da tagliare (max. 7 fogli 80g/m2-di carta, max. 1 carta di credito, max 1 CD). Spingere l'interruttore w in posizione , qualora il materiale da tagliare sia rimasto incastrato. In tal modo viene azionata la retromarcia e il materiale da tagliare viene fatto fuoriuscire nuovamente. Impostare l'interruttore w in posizione (OFF), non appena ottenuta la fuoriuscita del materiale da tagliare. Se l'apparecchio improvvisamente si arresta: significa che l'apparecchio surriscaldato e che si attivato il dispositivo di sicurezza di spegnimento automatico. Attenzione: estrarre la spina dalla presa di corrente per evitare un'accensione involontaria. Spegnere l'apparecchio spostando l'interruttore w in posizione centrale (OFF). Fare raffreddare l'apparecchio. Reinserire la spina nella presa. Aaccendere l'apparecchio spostando l'interruttore w in posizione . Se l'apparecchio non si accende: controllare che la spina sia stata inserita nella presa di corrente. Provare con un'altra presa di corrente. L'apparecchio molto probabilmente guasto. Far controllare l'apparecchio da personale specializzato qualificato.
Se l'apparecchio acceso, ma il procedi-mento di taglio non ancora cominciato: l'apparecchio surriscaldato e il dispositivo di spegnimento automatico di sicurezza attivato. Attenzione: estrarre la spina dalla presa di corrente per evitare un'accensione involontaria. Spegnere l'apparecchio spostando l'interruttore w in posizione centrale (OFF). Fare raffreddare l'apparecchio. Reinserire la spina nella presa. Accendere l'apparecchio spostando l'interruttore w in posizione . Il dispositivo di taglio q non stato collocato correttamente. Collocare correttamente il dispositivo di taglio q.
- 12 -
CONTENT
Indicaciones de seguridad importantes Intended Use m Important safety instructions Technical data Items supplied Appliance description Commissioning Operation Emptying the waste container Cleaning Disposal Warranty & Service Importer Troubleshooting
PAGE
2 14 14 15 15 15 15 15 16 17 17 17 18 18
Read the operating instructions carefully before using the appliance for the first time and preserve this booklet for later reference. Pass the manual on to whomsoever might acquire the appliance at a later date.
- 13 -
- 14 -
Appliance description
q Cutter attachment w Switch e Cutter opening for CD/Credit cards r Cutter opening for paper t Large waste receptacle (Paper) y Power cable u Small waste receptacle (transparent) /
Viewing window
Commissioning
First of all, place the cutter attachment q onto the large waste receptacle t so that the power cable y is located at the rear, i.e. on the closed side. Slide the small waste receptacle u for plastics in the opening on the front side of the large waste receptacle t. Connect the paper shredder to a power socket.
Technical data
Mains voltage: Nominal current: Rated output: Protection class: Cutting process for Paper: Working width: CO Time: 220-240 V ~ 50Hz 1,8 A 380 W II Crosscut, 4x18 mm particles 223 mm 3 minutes
Operation
Switching the appliance on: Place the switch w to the position shredding. for
CO Time The C.O. Time (Continuous Operation) details how long an appliance may be used without the motor overheating and being damaged. After the appliance has run for for this period it must be switched off until the motor has cooled itself down.
Inserting paper: Insert paper from above and in portrait format into the cutter opening for paper r. The motor starts automatically and switches itself off automatically if no further paper is inserted. You can shred up to 7 sheets (80g/m2 paper) at the same time.
Items supplied
Shredder KH 4407 Operating Instructions
- 15 -
Inserting credit cards: Open the safety flap over the cutter opening for CD/Credit cards e. Insert the credit card from above into the middle of the CD/Credit card cutter opening e. You can only shred one credit card at a time. ALWAYS insert them into the CD/Credit card cutter opening e with the broad side leading. If you do not, the magnetic strip will not be destroyed. Note: Always insert the credit card into the middle of the cutter opening e. If you do not, the shredding process will not start! Inserting a CD: Insert the CD from above into the middle of the CD/Credit card cutter opening e. You can only shred one CD at a time. Warning!: NEVER place a finger into the central hole of a CD when you are feeding it into the appliance. Clearing a material blockage: Press and hold the switch w in position should the item to be shredded become jammed. The appliance now goes into reverse and the material to be shredded is returned. Place the switch w into position (OFF) as soon as the jammed item is returned. Switching the appliance off: To switch the appliance off, move the switch w into the middle position (OFF).
- 16 -
Cleaning
Danger! Always remove the power plug before cleaning the appliance. There is a risk of electric shock! Warning!! The cutters in the appliance are very sharp! Risk of personal injury! Empty the waste containers t/u regularly. Clean the waste containers t/u and the cutter attachment q with a lightly moistened cloth and, if required, with a mild detergent. Remove possible residues in the cutter openings e/r with a suitable object. Ensure that the appliance is unplugged before commencing this!
Disposal
Do not dispose of the appliance in your normal domestic waste. This product is subject to the European guideline 2002/96/EC. Dispose of the appliance through an approved disposal centre or at your community waste facility. Observe the currently applicable regulations. In case of doubt, please contact your waste disposal centre. Dispose of all packaging materials in an environmentally responsible manner.
e-mail: support.ie@kompernass.com
- 17 -
Importer
KOMPERNASS GMBH BURGSTRASSE 21 44867 BOCHUM, GERMANY www.kompernass.com
If the appliance doesn`t allow itself to be switched on: Check that the plug is correctly connected to a wall socket. Try out a different wall socket. The appliance is probably defective. Have the appliance checked by qualified specialists. When the appliance is switched on, however, the shredding process will not start: The appliance has overheated and triggered the automatic safety switch-off. Important: Remove the power plug from the wall socket to avoid an unintended starting of the appliance. To switch the appliance off, move the switch w into the middle position (OFF). Allow the appliance to cool down. Replace the power plug into the socket. Switch the appliance on, in that the switch w is placed in the position . The cutter attachment q is not correctly placed. Place the cutting attachment q in the correct position.
Troubleshooting
If the material to be shredded jams: This means that you have attempted to feed too much material into the appliance (max. 7 sheets 80g/m2 paper, max. 1 credit card, max. 1 CD/DVD). Place the switch w in position should the item to be shredded become jammed. The appliance now goes into reverse and the material to be shredded is returned. Place the switch w in position (OFF), as soon as the jammed item is returned. If the appliance suddenly ceases operation: This means that the appliance has overheated and the automatic safety cut-out has activated itself. Important: Remove the power plug from the wall socket to avoid an unintended starting of the appliance To switch the appliance off, move the switch w into the middle position (OFF). Allow the appliance to cool down. Reinsert the power plug into the socket. Switch the appliance on, in that the switch w is placed in the position .
- 18 -
INHALTSVERZEICHNIS
Bestimmungsgemer Gebrauch Wichtige Sicherheitshinweise Technische Daten Lieferumfang Gertebeschreibung Inbetriebnahme Bedienung Auffangbehlter leeren Reinigung Entsorgen Garantie und Service Importeur Im Fehlerfall
SEITE
20 20 21 21 21 21 21 22 22 23 23 23 23
Lesen Sie die Bedienungsanleitung vor der ersten Verwendung aufmerksam durch und heben Sie diese fr den spteren Gebrauch auf. Hndigen Sie bei Weitergabe des Gertes an Dritte auch die Anleitung aus.
- 19 -
AKTENVERNICHTER KH 4407
Bestimmungsgemer Gebrauch
Der Aktenvernichter ist ausschlielich zum Zerkleinern von Papier, Kreditkarten und CDs geeignet. Jede andere Verwendung oder Vernderung gilt als nicht bestimmungsgem und birgt erhebliche Unfallgefahren.
Um Verletzungsgefahr zu vermeiden:
Den Aktenvernichter jeweils nur durch eine Person bedienen. Das Gert whrend des Betriebs niemals unbeaufsichtigt lassen. Halten Sie lose Kleidung , langes Haar , Schmuck u.. von den Schneidffnungen fern. Stecken Sie nie die Finger in die Schneidffnungen . Stecken Sie nicht Ihre Finger in das zentrale Loch der CD, wenn Sie diese in das Gert einfhren. Halten Sie Tiere vom Gert fern. Diese knnen sich verletzen. Dieses Gert ist nicht dafr bestimmt, durch Personen (einschlielich Kinder) mit eingeschrnkten physischen, sensorischen oder geistigen Fhigkeiten oder mangels Erfahrung und/oder mangels Wissen benutzt zu werden, es sei denn, sie werden durch eine fr ihre Sicherheit zustndige Person beaufsichtigt oder erhielten von ihr Anweisungen, wie das Gert zu benutzen ist. Das Verpackungsmaterial stellt eine Gefahr fr Kinder dar. Entsorgen Sie das Verpackungsmaterial nach dem Auspacken sofort oder bewahren Sie es fr Kinder unzugnglich auf. Verlegen Sie das Netzkabel so, dass niemand darauf treten oder darber stolpern kann.
Wichtige Sicherheitshinweise
Die folgenden Sicherheitshinweise mssen beim Einsatz von elektrischen Gerten in jedem Fall bercksichtigt werden: Stellen Sie das Gert nicht in der Nhe von Wrme- oder Wasserquellen auf. Benutzen Sie das Gert nicht in staubigen oder explosionsgefhrdeten Umgebungen (entzndliche Gase, Dmpfe, Dmpfe von organischen Lsungsmitteln). Benutzen Sie das Gert nicht im Freien.
- 20 -
Seien Sie stets aufmerksam! Achten Sie immer darauf was Sie tun und gehen Sie stets mit Vernunft vor. Benutzen Sie das Gert in keinem Fall, wenn Sie unkonzentriert sind oder sich unwohl fhlen.
Inbetriebnahme
Setzen Sie zunchst den Schneidaufsatz q so auf den groen Auffangbehlter t, dass das Netzkabel y nach hinten, an der geschlossenen Seite, angebracht ist. Schieben Sie den kleinen Auffangbehlter u fr Kunststoff in die ffnung an der Vorderseite des groen Auffangbehlters t. Schlieen Sie den Aktenvernichter an eine Steckdose an.
Technische Daten
Netzspannung: Nennstrom: Nennleistung: Schutzklasse: Schnittverfahren fr Papier: Arbeitsbreite: KB Zeit: 220-240 V ~ 50Hz 1,8 A 380 W II Kreuzschnitt, 4x18 mmPartikel 223 mm 3 Minuten
Bedienung
Gert einschalten: Stellen Sie den Schalter w zum Zerkleinern in die Position . Papier einfhren: Fhren Sie das Papier im Hochformat von oben in die Schneidffnung fr Papier r ein. Der Motor startet automatisch und schaltet auch automatisch wieder ab, wenn kein weiteres Papier zugefhrt wird. Sie knnen bis zu 7 Blatt (80g/m2-Papier) gleichzeitig schneiden. Kreditkarte einfhren: ffnen Sie die Sicherheitsklappe ber der CD/Kreditkarten-Schneidffnung e. Fhren Sie die Kreditkarte von oben mittig in die CD-/Kreditkarten-Schneidffnung e ein. Sie knnen jeweils nur eine Kreditkarte schneiden. Fhren Sie diese immer mit der breiten Seite voran in die CD-/Kreditkarten-Schneidffnung e ein. Ansonsten wird der Magnetstreifen nicht zerstrt. Hinweis: Fhren Sie die Kreditkarte immer mittig in die CD-/Kreditkarten-Schneidffnung e ein. Ansonsten startet der Schneidvorgang nicht!
KB-Zeit Die KB-Zeit (Kurzzeitbetrieb) gibt an, wie lange man ein Gert betreiben kann, ohne dass der Motor berhitzt und Schaden nimmt. Nach der angegebenen KB-Zeit muss das Gert solange ausgeschaltet werden, bis sich der Motor abgekhlt hat.
Lieferumfang
Aktenvernichter KH 4407 Bedienungsanleitung
Gertebeschreibung
q Schneidaufsatz w Schalter e Schneidffnung CD/Kreditkarte r Schneidffnung Papier t Groer Auffangbehlter (Papier) y Netzkabel u Kleiner Auffangbehlter
(transparent) / Sichtfenster
- 21 -
CD einfhren: Fhren Sie die CD mittig von oben in die CD/Kreditkarten-Schneidffnung e ein. Sie knnen jeweils nur eine CD schneiden. Warnung: Stecken Sie nicht Ihre Finger in das zentrale Loch der CD, wenn Sie diese in das Gert einfhren. Materialstau beheben: Schieben Sie den Schalter w in die Position , falls das Schneidgut stecken bleibt. Der Rckwrtslauf ist nun eingeschaltet und das Schneidgut wird wieder ausgegeben. Stellen Sie den Schalter w in die Position (OFF), sobald das Schneidgut ausgegeben ist. Gert ausschalten: Schalten Sie das Gert aus, indem Sie den Schalter w in die mittlere Position (OFF) stellen.
Kleinen Auffangbehlter (Plastik) leeren Ziehen Sie den kleinen Auffangbehlter u nach vorne aus dem groen Auffangbehlter t, um ihn zu leeren. Setzen Sie ihn nach der Leerung wieder ein. Hinweis zur berhitzung des Gertes: Bei berhitzung schaltet das Gert automatisch ab. Achtung: Ziehen Sie den Netzstecker aus der Steckdose, um ein unbeabsichtigtes Einschalten zu vermeiden. Schalten Sie das Gert aus, indem Sie den Schalter w in die mittlere Position (OFF) stellen. Leeren Sie die Auffangbehlter t/u. Lassen Sie das Gert abkhlen. Stecken Sie den Netzstecker wieder in die Steckdose. Schalten Sie das Gert ein, indem Sie den Schalter w in die Position stellen.
Auffangbehlter leeren
Leeren Sie die Auffangbehlter t/u regelmig aus. Fhren Sie die Abflle einer umweltgerechten Entsorgung zu. Groen Auffangbehlter (Papier) leeren Achtung: Ziehen Sie den Netzstecker aus der Steckdose, um ein unbeabsichtigtes Einschalten zu vermeiden. Nehmen Sie den Schneidaufsatz q vom groen Auffangbehlter t. Ziehen Sie den kleinen Auffangbehlter u nach vorne aus dem groen Auffangbehlter t, damit er nicht heraus fllt. Leeren Sie den groen Auffangbehlter t und setzen Sie wieder alle Teile zusammen.
Reinigung
Gefahr! Ziehen Sie vor jeder Reinigung den Netzstecker. Es besteht die Gefahr eines elektrischen Schlages! Warnung! Die Schneidmesser des Gerts sind sehr scharf! Verletzungsgefahr! Leeren Sie die Auffangbehlter t/u regelmig aus. Reinigen Sie die Auffangbehlter t/u und den Schneidaufsatz q mit einem leicht befeuchteten Tuch und ggf. mit einem milden Reinigungsmittel. Entfernen Sie eventuelle Rckstnde in den Schneidffnungen e/r mit einem geeigneten Gegenstand. Stellen Sie sicher, dass dabei der Netzstecker gezogen ist.
- 22 -
Entsorgen
Werfen Sie das Gert keinesfalls in den normalen Hausmll. Dieses Produkt unterliegt der europischen Richtlinie 2002/96/EC. Entsorgen Sie das Gert ber einen zugelassenen Entsorgungsbetrieb oder ber Ihre kommunale Entsorgungseinrichtung. Beachten Sie die aktuell geltenden Vorschriften. Setzen Sie sich im Zweifelsfall mit Ihrer Entsorgungseinrichtung in Verbindung. Fhren Sie alle Verpackungsmaterialien einer umweltgerechten Entsorgung zu.
Schraven Service- und Dienstleistungs GmbH Gewerbering 14 47623 Kevelaer, Germany Tel.: +49 (0) 180 5 008107
(14 Ct/Min. aus dem dt. Festnetz ggf. abweichende Preise aus den Mobilfunknetzen)
Fax: +49 (0) 2832 3532 e-mail: support.de@kompernass.com Komperna Service sterreich Tel.: 0820 899 913 (0,20 EUR/Min.) e-mail: support.at@kompernass.com Komperna Service Switzerland Tel.: 0848 000 525 (max. 0,0807 CHF/Min.) e-mail: support.ch@kompernass.com
Importeur
KOMPERNASS GMBH BURGSTRASSE 21 44867 BOCHUM, GERMANY www.kompernass.com
Im Fehlerfall
Wenn das Schneidgut im Gert stecken bleibt: Dies bedeutet, dass Sie zu viel Schneidgut in das Gert eingefhrt haben (max. 7 Blatt 80g/m2-Papier, max. 1 Kreditkarte, max. 1 CD/DVD). Schieben Sie den Schalter w in die Position , falls das Schneidgut stecken bleibt. Der Rckwrtslauf ist nun eingeschaltet und das Schneidgut wird wieder ausgegeben. Stellen Sie den Schalter w in die Position (OFF), sobald das Schneidgut ausgegeben ist.
- 23 -
Wenn das Gert pltzlich stehen bleibt: Dies bedeutet, dass das Gert berhitzt ist und sich die automatische Sicherheitsabschaltung aktiviert hat. Achtung: Ziehen Sie den Netzstecker aus der Steckdose, um ein unbeabsichtigtes Einschalten zu vermeiden. Schalten Sie das Gert aus, indem Sie den Schalter w in die mittlere Position (OFF) stellen. Lassen Sie das Gert abkhlen. Stecken Sie den Netzstecker wieder in die Steckdose. Schalten Sie das Gert ein, indem Sie den Schalter w in die Position stellen. Wenn sich das Gert nicht einschalten lsst: berprfen Sie, ob sich der Netzstecker in der Steckdose befindet. Probieren Sie eine andere Steckdose aus. Das Gert ist eventuell defekt. Lassen Sie das Gert von qualifiziertem Fachpersonal berprfen. Wenn das Gert eingeschaltet ist, jedoch nicht den Schneidvorgang startet: Das Gert ist berhitzt und die automatische Sicherheitsabschaltung ist aktiviert. Achtung: Ziehen Sie den Netzstecker aus der Steckdose, um ein unbeabsichtigtes Einschalten zu vermeiden. Schalten Sie das Gert aus, indem Sie den Schalter w in die mittlere Position (OFF) stellen. Lassen Sie das Gert abkhlen. Stecken Sie den Netzstecker wieder in die Steckdose. Schalten Sie das Gert ein, indem Sie den Schalter w in die Position stellen.
Der Schneidaufsatz q ist nicht richtig aufgesetzt. Setzen Sie den Schneidaufsatz q richtig auf.
- 24 -