Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
ANSI/AWWA-C110/A21.10 Standard
and
ANSI B16.1 Class 125 Standard
SPECIFICATIONS
Flanged fittings shown on the pages immediately following are manufactured to either ANSI/AWWA-C110/
A21.10 or to ANSI B16.1 standard as indicated on each page heading. Elbows or bends (straight sizes),
tees, crosses, concentric reducers, base elbows (except reducing size) and bottom base tees are manufactured to ANSI/AWWA-C110/A21.10 standard. These fittings have identical face to face and center to
face dimensions and the same flange drilling as ANSI B16.1 fittings, but differ slightly in wall thickness.
Ductile iron C110/A21.10 flanged fittings are rated for 150 or 250 psi water working pressure as listed in
the tables.
Long radius and reducing elbows, reducing on-the-run tees, side outlet fittings, eccentric reducers and laterals are ANSI B16.1 Class 125 fittings. Ductile iron Class 125 fittings are furnished manufacturer's standard for 250 psi water working pressure. Flanged offsets and true wyes are furnished manufacturer's
standard.
We do not spot face back of flanges. Where spot facing is required, the back of the flange is machined
over its entire surface.
When ordering any flanged fittings equipped with bosses and/or tapped holes, refer to and use the letter
key on page 63, which designates location by letter.
Standard 125 pound template for drilling shown below is used for all flanged fittings whether ANSI/AWWAC110/A21.10 or ANSI B16.1.
Note: The flanges shown above are adequate for 250 psi water working pressure. They should not be confused with 250 pound extra heavy flanges covered by ANSI B16.1 which are rated for 250 psi steam working pressure.
DIMENSIONS
Nominal
Pipe
Size
2
3
4
5
6
8
10
12
14
16
18
20
24
30
36
Dimensions Inches
Flange
O.D.
6
7 1/2
9
10
11
13 1/2
16
19
21
23 1/2
25
27 1/2
32
38 3/4
46
Bolt
Circle
4 3/4
6
7 1/2
8 1/2
9 1/2
11 3/4
14 1/4
17
18 3/4
21 l/4
22 3/4
25
29 l/2
36
42 3/4
Flange
Thickness T
5/8
3/4
15/16
15/16
1 15/16
1 1/8
1 3/16
1 1/4
1 3/8
1 7/16
1 9/16
1 11/l6
1 7/8
2 1/8
2 3/8
Bolt Hole
Diameter
3/4
3/4
3/4
7/8
7/8
7/8
1
1
l 1/8
1 1/8
1 1/4
1 1/4
1 3/8
1 3/8
1 5/8
Bolt Diameter
and Length
5/8 x 2 1/4
5/8 x 2 1/2
3/4 x 3
3/4 x 3
3/4 x 3 1/4
3/4 x 3 1/2
7/8 x 3 3/4
7/8 x 3 3/4
1 x 4 1/4
1 x 4 1/2
l 1/8 x 4 3/4
1 1/8 x 5
1 1/4 x 5 1/2
1 1/4 x 6 1/2
1 1/2 x7
Number
of
Bolts
4
4
8
8
8
8
12
12
12
16
16
20
20
28
32
Note: Drilling templates are in multiples of four, so that fittings may be made to face in any quarter. Bolt
holes shall straddle the center line.
52
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
Reducing on
Outlet
Reducing on
One Run
Reducing on
One Run & Outlet
Reducing on
Both Runs
REDUCING CROSSES
Reducing
on
One Outlet
Reducing
on
Both Outlets
Reducing on
One Run
and One Outlet
Reducing on
One Run
and Both Outlets
REDUCING LATERALS
Reducing on
Branch
Reducing on
One Run
Right Hand
Left Hand
Reducing on One
Run and Branch
Reducing
True Y
Right Hand
Left Hand
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
53
90 Elbow
Straight Size
90 Elbow
Tee
Straight Size
Cross
Straight Size
90 Elbow
Reducing Size
Tee
Reducing Size
Cross
Reducing Size
45 Lateral
Straight Size
90 Base Elbow
Base Tee
Eccentric Reducer
45 Elbow
Reducer
Tapping through the wall of the fitting is limited to sizes indicated in the table below. Larger size tapped
openings will require casting the fitting with an intergral bossthe location of which may also be identified
by a letter, as explained above. A boss is always required at V and Y on straight and reducing sizes of
90 elbows, and on tapered sizes of reducers.
Maximum Size of Tapped Hole in Fitting
Size of fitting inches
Size of hole without boss inches
Size of hole with boss inches
54
3
3/8
2
4
3/8
2 1/2
5
3/8
2 1/2
6
1/2
3
8
3/4
4
10
1
4
12
1 1/2
4
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
14-36
2
4
Flanged 90 Bend
Nominal
Diameter
Inches
Pressure
Rating
psi
Flanged 45 Bend
DIMENSIONS AND WEIGHTS
90 Bend
Body
Thickness
Ductile
T
3
250
.48
4
250
.52
5*
250*
.50
6
250
.55
8
250
.60
10
250
.68
12
250
.75
14
250
.66
16
250
.70
18
250
.75
20
250
.80
24
250
.89
30
250
1.03
*Five inch size is ANSI B16.1 fitting.
Dimensions
Inches
A
5.5
6.5
7.5
8.0
9.0
11.0
12.0
14.0
15.0
16.5
18.0
22.0
25.0
R
4.00
4.50
...
6.00
7.00
9.00
10.00
11.50
12.50
14.00
15.50
18.50
21.50
Approximate
Weight
Pounds
25
45
52
65
105
165
235
330
430
530
685
1085
1755
Nominal
Diameter
Inches
Pressure
Rating
psi
45 Bend
Dimensions
Inches
A
3.0
4.0
4.5
5.0
5.5
6.5
7.5
7.5
8.0
8.5
9.5
11.0
15.0
R
3.62
4.81
...
7.25
8.44
10.88
13.25
12.06
13.25
14.50
16.88
18.12
27.75
Approximate
Weight
Pounds
20
40
45
55
90
130
195
245
315
375
485
730
1335
Body
Thickness
Dimensions
Inches
Ductile
T
A
R
3
250
.48
3.0
7.56
4
250
.52
4.0
10.06
6
250
.55
5.0
15.06
8
250
.60
5.5
17.62
10
250
.68
6.5
22.62
12
250
.75
7.5
27.62
14
250
.66
7.5
25.12
16
250
.70
8.0
27.62
18
250
.75
8.5
30.19
20
250
.80
9.5
35.19
24
250
.89
11.0 37.69
30
250
1.03
15.0 57.81
Flange accessories must be ordered separately.
Approximate
Weight
Pounds
20
40
55
90
130
195
250
315
385
505
755
1135
11 1/4 Bend
Dimensions
Inches
A
3.0
4.0
5.0
5.5
6.5
7.5
7.5
8.0
8.5
9.5
11.0
15.0
R
15.25
20.31
30.50
35.50
45.69
55.81
50.75
55.81
60.94
71.06
76.12
116.75
Approximate
Weight
Pounds
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
20
40
55
90
130
195
245
315
385
505
760
1395
55
Nominal
Pipe
Size
Inches
4x3
5x4
6x4
6x5
8x4
8x5
8x6
10 x 4
10 x 5
10 x 6
10 x 8
12 x 6
12 x 8
12 x 10
14 x 6
14 x 8
14 x 10
Dimensions
Inches
T
T1
.50
.50
.56
.56
.62
.62
.62
.75
.75
.75
.75
.81
.81
.81
.81
.81
.87
.37
.50
.50
.50
.50
.50
.56
.50
.50
.56
.62
.56
.62
.75
.56
.62
.75
6.50
7.50
8.00
8.00
9.00
9.00
9.00
11.00
11.00
11.00
11.00
12.00
12.00
12.00
14.00
14.00
14.00
Reducing 90 Elbow
DIMENSIONS AND WEIGHTS
Nominal
Dimensions
Approximate
Pipe
Inches
Weight
Size
Ponds
T
T1
A
Inches
35
14 x 12
.87 .81 14.00
48
16 x 8
1.0 .62 15.00
55
16 x 10
1.0 .75 15.00
60
16 x 12
1.0 .81 15.00
75
16 x 14
1.0 .87 15.00
82
18 x 12
1.06 .81 16.50
90
18 x 14
1.06 .87 16.50
105
18 x 16
1.06 1.0 16.50
115
20 x 12
1.12 .81 18.00
125
20 x 14
1.12 .87 18.00
150
20 x 16
1.12 1.0 18.00
165
20 x 18
1.12 1.06 18.00
190
24 x 14
1.25 .87 22.00
220
24 x 16
1.25 1.0 22.00
230
24 x 18
1.25 1.06 22.00
240
24 x 20
1.25 1.12 22.00
280
...
...
...
...
Approximate
Weight
Pounds
320
300
340
380
420
440
480
540
520
570
640
680
865
880
930
1010
...
56
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
Straight
90 Long Radius Elbow
Reducing
90 Long Radius Elbow
DIMENSIONS AND WEIGHTS
Nominal
Dimensions Inches Approximate
Nominal
Pipe Size
Weight
Pipe Size
T
T1
B
Inches
Pounds
Inches
3x3
.37 . . .
7.75
28
14 x 10
4x4
.50 . . .
9.00
50
14 x 12
5x4
.50 .50
10.25
60
14 x 14
5x5
.50 . . .
10.25
62
16 x 8
6x4
.56 .50
11.50
70
16 x 10
6x5
.56 .50
11.50
75
16 x 12
6x6
.56 . . .
11.50
80
16 x 14
8x4
.62 .50
14.00
100
16 x 16
8x5
.62 .50
14.00
110
18 x 12
8x6
.62 .56
14.00
120
18 x14
8x8
.62 . . .
14.00
140
18 x16
10 x 4
.75 .50
16.50
145
18 x 18
10 x 6
.75 .56
16.50
170
20 x 14
10 x 8
.75 .62
16.50
195
20 x 16
l0 x l0
.75 . . .
16.50
230
20 x 20
12 x 6
.81 .56
19.00
225
24 x 14
12 x 8
.81 .62
19.00
260
24 x 16
12 x 10
.81 .75
19.00
300
24 x 18
12 x 12
.81 . . .
19.00
325
24 x 20
14 x 8
.87 .62
21.50
330
24 x 24
For Pressure Ratings and For Drilling Template See Page 52
Dimensions Inches
T
T1
.87
.87
.87
1.0
1.0
1.0
1.0
1.0
1.06
1.06
1.06
1.06
1.12
1.12
1.12
1.25
1.25
1.25
1.25
1.25
.75
.81
...
.62
.75
.81
.87
...
.81
.87
1
...
.87
1.0
...
1.25
1.25
1.25
1.25
1.25
21.50
21.50
21.50
24.00
24.00
24.00
24.00
24.00
26.50
16.50
26.50
26.50
29.00
29.00
29.00
34.00
34.00
34.00
34.00
34.00
Approximate
Weight
Pounds
375
425
475
420
480
530
590
630
635
480
775
840
820
915
1080
1280
1300
1365
1430
1640
57
D1
3
4
4
6
4
6
8
6
8
10
8
10
12
12
14
16
18
20
24
Working
Pressure psi
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
Dimensions Inches
A
5.50
6.50
6.50
8.00
6.50
8.00
9.00
8.00
9.00
11.00
9.00
11.00
12.00
14.00
14.00
15.00
16.50
18.00
22.00
B
3.00
3.00
3.50
3.50
4.50
4.50
4.50
5.00
5.00
5.00
5.50
5.50
5.50
5.50
6.00
6.50
7.00
8.00
9.00
Approximate
Weight Pounds
35
50
75
80
85
120
125
140
155
220
210
240
315
375
415
520
630
780
1250
Regularly furnished with flanges faced and drilled per template on page 52.
Larger sizes can be made to order. Detailed information furnished on request.
Flange accessories must he ordered separately.
NOTE: When ordering reducing fittings, give size of openings in the order indicated by numerals 1,
2 and 3.
58
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
Cross
DIMENSIONS AND WEIGHTS
Dimensions Inches
Run
Branch
Ductile
T1
Tee
Cross
3
3
4
4
4
5*
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
14
14
14
14
14
14
16
16
16
16
16
16
16
18
18
18
18
18
18
18
20
20
20
20
20
20
20
20
2
3
2
3
4
5*
2
3
4
6
3
4
6
8
4
6
8
10
4
6
8
10
12
4
6
8
10
12
14
4
6
8
10
12
14
16
6
8
10
12
14
16
18
6
8
10
12
14
16
18
20
250
250
250
250
250
250*
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
.48
.48
.52
.52
.52
.50
.55
.55
.55
.55
.60
.60
.60
.60
.68
.68
.68
.80
.75
.75
.75
.87
.87
.66
.66
.66
.66
.82
.82
.70
.70
.70
.70
.70
.89
.89
.75
.75
.75
.75
.75
.75
.75
.80
.80
.80
.80
.80
.80
.80
.80
.48
48
.48
.48
.52
.50
.48
.48
.52
.55
.52
.52
.55
.60
.52
.55
.60
.80
.52
.55
.60
.80
.87
.55
.55
.60
.68
.75
.82
.55
.55
.60
.68
.75
.82
.89
.55
.60
.68
.75
.66
.70
.75
.55
.60
.68
.75
.66
.70
.75
.80
5.5
5.5
6.5
6.5
6.5
7.5
8.0
8.0
8.0
8.0
9.0
9.0
9.0
9.0
11.0
11.0
11.0
11.0
12.0
12.0
12.0
12.0
12.0
14.0
14.0
14.0
14.0
14.0
14.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
13.0
13.0
13.0
13.0
16.5
16.5
16.5
14.0
14.0
14.0
14.0
14.0
18.0
18.0
18.0
5.5
5.5
6.5
6.5
6.5
7.5
8.0
8.0
8.0
8.0
9.0
9.0
9.0
9.0
11.0
11.0
11.0
11.0
12.0
12.0
12.0
12.0
12.0
14.0
14.0
14.0
14.0
14.0
14.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.5
15.5
15.5
15.5
16.5
16.5
16.5
17.0
17.0
17.0
17.0
17.0
18.0
18.0
18.0
35
40
50
60
60
81
85
85
90
95
130
140
145
155
205
215
225
270
290
295
310
360
385
410
420
435
450
470
500
525
540
555
565
590
610
635
480
570
580
605
740
760
785
710
720
735
755
770
950
820
1005
...
50
...
70
80
105
...
95
110
120
140
155
165
195
220
240
265
330
310
320
345
415
460
...
450
475
460
555
595
...
565
590
620
665
700
755
505
535
560
670
720
765
915
635
665
685
820
745
1065
945
1175
59
Cross
DIMENSIONS AND WEIGHTS
Nominal Diameter Inches Pressure Rating psi Dimensions Inches Approximate Weight Pounds
Run
24
24
24
24
24
24
24
24
24
30
30
30
30
30
30
30
30
30
30
Branch
6
8
10
12
14
16
18
20
24
6
8
10
12
14
16
18
20
24
30
Ductile
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
T
.89
.89
.89
.89
.89
.89
.89
.89
.89
1.03
1.03
1.03
1.03
1.03
1.03
1.03
1.03
1.03
1.03
T1
.55
.60
.68
.75
.66
.70
.75
.80
.89
.55
.60
.68
.75
.66
.70
.75
.80
.89
1.03
H
15.0
15.0
15.0
15.0
15.0
15.0
22.0
22.0
22.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
25.0
25.0
J
19.0
19.0
19.0
19.0
19.0
l9.0
22.0
22.0
22.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
25.0
25.0
Tee
1000
1010
1020
1040
1050
1070
1470
1510
1585
1725
1450
1465
1780
1490
1505
1815
1540
2475
2615
Cross
875
895
930
1100
1125
1160
1365
1695
1850
1470
1495
1520
1565
1570
1605
1615
1670
2695
2980
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
Dimensions Inches
T
.50
.56
.56
.62
.62
.62
.75
.75
.75
.75
.75
.81
.81
.81
.81
.81
.81
.81
.81
.81
.87
.87
T1
.37
.50
.50
.56
.56
.56
.62
.62
.62
.62
.62
.56
.56
.62
.62
.62
.75
.75
.75
.75
.81
.81
T2
.37
.50
.56
.50
.56
.62
.56
.56
.56
.62
.75
.56
.62
.56
.62
.81
.56
.62
.75
.81
.81
.87
A
6.50
8.00
8.00
9.00
9.00
9.00
11.00
11.00
11.00
11.00
11.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
14.00
14.00
H
6.50
8.00
8.00
9.00
9.00
9.00
11.00
11.00
11.00
11.00
1l.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
14.00
14.00
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
61
DimensionsInches
T
T1
T2
16 x 14 x 14
1.0
.87
.87
15.00 15.00
16 x 14 x 16
1.0
.87
1.0
15.00 15.00
18 x 12 x 12
1.06
.81
.81
13.00 15.50
18 x 12 x 14
1.06
.81
.87
16.50 16.50
18 x 12 x 18
1.06
.81
1.06 16.50 16.50
18 x 14 x 12
1.06
.87
.81
13.00 15.50
18 x 14 x 14
1.06
.87
.87
16.50 16.50
18 x 14 x 18
1.06
.87
1.06 16.50 16.50
18 x 16 x 18
1.06
1.0
1.06 16.50 16.50
20 x 16 x 14
1.12
1.0
.87
14.00 17.00
20 x 16 x 16
1.12
1.0
1.0
18.00 18.00
20 x 16 x 20
1.12
1.0
1.12 18.00 18.00
20 x 18 x 20
1.12 1.06 1.12 18.00 18.00
24 x 16 x 16
1.25
1.0
1.0
15.00 19.00
24 x 16 x 18
1.25
1.0
1.06 22.00 22.00
24 x 16 x 24
1.25
1.0
1.25 22.00 22.00
24 x 18 x 16
1.25 1.06
1.0
15.00 19.00
24 x 18 x 18
1.25 1.06 1.06 22.00 22.00
24 x 18 x 24
1.25 1.06 1.25 22.00 22.00
24 x 20 x 24
1.25 1.12 1.25 22.00 22.00
30 x 16 x 16
1.03
.68
1.06 18.00 23.00
30 x 16 x 18
1.03
.68
.75
18.00 23.00
30 x 16 x 20
1.03
.68
.81 18.00 23.00
30 x 16 x 24
1.03
.68
.87
25.00 25.00
30 x 16 x 30
1.03
.68
1.03 25.00 25.00
30 x 18 x 16
1.03
.75
1.06 18.00 23.00
30 x 18 x 18
1.03
.75
.75
18.00 23.00
30 x 18 x 20
1.03
.75
.81
18.00 23.00
30 x 18 x 24
1.03
.75
.87
25.00 25.00
30 x 18 x 30
1.03
.75
1.03 25.00 25.00
30 x 20 x 16
1.03
.81
1.06 18.00 23.00
30 x 20 x 18
1.03
.81
.75
18.00 23.00
30 x 20 x 20
1.03
.81
.81 18.00 23.00
30 x 20 x 24
1.03
.81
.87
25.00 25.00
30 x 20 x 30
1.03
.81
1.03 25.00 25.00
30 x 24 x 16
1.03
.87
1.06 18.00 23.00
30 x 24 x 18
1.03
.87
.75
18.00 23.00
30 x 24 x 20
1.03
.87
.81
18.00 23.00
30 x 24 x 24
1.03
.87
.87
25.00 25.00
30 x 24 x 30
1.03
.87
1.03 25.00 25.00
Tees with branch and run openings smaller than those listed are also available.
Tees reducing on both runs are also available.
62
650
680
610
750
810
615
755
815
825
780
975
1040
1030
1085
1495
1635
1070
1485
1625
1630
1345
1350
1375
1815
1960
1335
1340
1365
1805
1955
1340
1345
1370
1815
1960
1340
1345
1370
1820
1965
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
Dimensions Inches
Large End
Small End
Ductile
T1
Approximate
Weight Pounds
3
4
4
6
6
6
6
8
8
8
8
10
10
10
12
12
12
12
14
14
14
14
16
16
16
16
16
18
18
18
18
18
20
20
20
20
20
24
24
24
24
24
30
30
30
30
2
2
3
2
3
4
5*
3
4
5*
6
4
6
8
4
6
8
10
6
8
10
12
6
8
10
12
14
8
10
12
14
16
10
12
14
16
18
12
14
16
18
20
16
18
20
24
250
250
250
250
250
250
250*
250
250
250*
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
.48
.52
.52
.55
.55
.55
.56
.60
.60
.62
.60
.68
.68
.68
.75
.75
.75
.75
.66
.66
.66
.66
.70
.70
.70
.70
.70
.75
.75
.75
.75
.75
.80
.80
.80
.80
.80
.89
.89
.89
.89
.89
1.03
1.03
1.03
1.03
.42
.48
.48
.48
.48
.52
.50
.48
.52
.50
.55
.52
.55
.60
.52
.55
.60
.68
.55
.60
.68
.75
.55
.60
.68
.75
.66
.60
.68
.75
.66
.70
.68
.75
.66
.70
.75
.75
.66
.70
.75
.80
.70
.75
.80
.89
6
7
7
9
9
9
9
11
11
11
11
12
12
12
14
14
14
14
16
16
16
16
18
18
18
18
18
19
19
19
19
19
20
20
20
20
20
24
24
24
24
24
30
30
30
30
16
25
30
30
40
45
50
60
65
71
75
85
90
110
120
130
145
170
165
185
205
234
210
230
255
286
315
265
290
320
350
385
340
375
405
445
470
535
565
610
645
695
945
970
1035
1155
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
63
Dimensions Inches
T
T1
.50
.50
.56
.56
.62
.62
.62
.62
.75
.75
.75
.81
.81
.81
.87
.87
.87
.87
1.0
1.0
1.0
1.0
1.0
1.06
1.06
1.06
1.06
1.06
1.12
1.12
1.12
1.12
1.12
1.25
1.25
1.25
1.25
1.25
.37
.37
.37
.50
.50
.50
.56
.56
.50
.56
.62
.56
.62
.75
.56
.62
.75
.81
.56
.62
.75
.81
.87
.62
.75
.81
.87
1.0
.75
.81
.87
1.0
1.06
.81
.87
1.0
1.06
1.12
7.00
8.00
9.00
9.00
9.00
11.00
11.00
11.00
12.00
12.00
12.00
14.00
14.00
14.00
16.00
16.00
16.00
16.00
18.00
18.00
18.00
18.00
18.00
19.00
19.00
19.00
19.00
19.00
20.00
20.00
20.00
20.00
20.00
24.00
24.00
24.00
24.00
24.00
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
Base Elbows
Nominal Diameter
Inches
3
4
6
8
10
12
14
16
18
20
24
30
Dimensions Inches
A
5.5
6.5
8.0
9.0
11.0
12.0
14.0
15.0
16.5
18.0
22.0
25.0
R
4.88
5.50
7.00
8.38
9.75
11.25
12.50
13.75
15.00
16.00
18.50
23.00
S
5.00
6.00
7.00
9.00
9.00
11.00
11.00
11.00
13.50
13.50
13.50
16.00
T
.56
.62
.69
.94
.94
1.00
1.00
1.00
1.12
1.12
1.12
1.19
U
.50
.50
.62
.88
.88
1.00
1.00
1.00
1.12
1.12
1.12
1.15
Approximate Weight
Pounds
35
55
85
145
210
300
400
505
645
805
1215
1945
Dimensions Inches
H
5.5
6.5
8.0
9.0
11.0
12.0
14.0
15.0
16.5
18.0
22.0
25.0
R
4.88
5.50
7.00
8.38
9.75
11.25
12.50
13.75
15.00
16.00
18.50
23.00
S
5.00
6.00
7.00
9.00
9.00
11.00
11.00
11.00
13.50
13.50
13.50
16.00
T
.56
.62
.69
.94
.94
1.00
1.00
1.00
1.12
1.12
1.12
1.19
U
.50
.50
.62
.88
.88
1.00
1.00
1.00
1.12
1.12
1.12
1.15
Approximate Weight
Pounds
50
70
115
195
300
450
570
710
900
1125
1715
2270
Dimension R is for machined bases. For bases not machined, add approximately 1/8 inch.
Flange accessories must be ordered separately.
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
65
*Dimensions J are for machined bases. For bases not machined, add approximately 1/8 inch.
Bases are not faced or drilled, unless specifically ordered.
Base ElbowsReducing Sizes
Starting with the 4 x 3 size, reducing sizes of base elbows are available in same range of sizes as shown on page 56 for
standard radius elbows and on page 66 for long radius elbows. Such fittings are regularly furnished with the base under
the larger size opening. Elbows with the base under the smaller size opening are strictly special.
Center-to-face dimensions of reducing elbows (as well as base dimensions) are same as for straight
size fittings corresponding to the size of the larger openingas shown in tables on this page.
ROUND BASE IS REGULAR
When bases are ordered drilled other than regular, a drawing must accompany the order.
Flange accessories must be ordered separately.
66
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
T
.37
.50
.50
.56
.56
.56
.62
.62
.62
.75
.75
.75
.75
.81
.81
.81
.81
.81
.87
.87
.87
.87
.87
1.0
1.0
1.0
1.0
1.0
1.0
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.12
1.12
1.12
1.12
1.12
1.12
1.12
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
1.37
T1
...
.37
...
.37
.50
...
.50
.56
...
.50
.56
.62
...
.50
.56
.62
.75
...
.56
.62
.75
1.18
...
.56
.62
.75
.81
.87
...
.56
.62
.75
.81
.87
1.0
...
.62
.75
.81
.87
1.0
1.06
...
.62
.75
.81
.87
1.0
1.06
1.12
...
.63
.75
.81
.88
1.00
1.06
1.13
1.25
1.37
Dimensions Inches
E
F
10.00
3.00
12.00
3.00
12.00
3.00
14.50
3.50
14.50
3.50
14.50
3.50
17.50
4.50
17.50
4.50
17.50
4.50
20.50
5.00
20.50
5.00
20.50
5.00
20.50
5.00
24.50
5.50
24.50
5.50
24.50
5.50
24.50
5.50
24.50
5.50
27.00
6.00
27.00
6.00
27.00
6.00
27.00
6.00
27.00
6.00
30.00
6.50
30.00
6.50
30.00
6.50
30.00
6.50
30.00
6.50
30.00
6.50
25.00
1.00
25.00
1.00
32.00
7.00
32.00
7.00
32.00
7.00
32.00
7.00
32.00
7.00
27.00
1.00
27.00
1.00
35.00
8.00
35.00
8.00
35.00
8.00
35.00
8.00
35.00
8.00
31.50
.50
31.50
.50
31.50
.50
40 50
9.00
40.50
9.00
40.50
9.00
40.50
9.00
40.50
9.00
39.0
0.0
39.0
0.0
39.0
0.0
39.0
0.0
49.0
10.0
49.0
10.0
49.0
10.0
49.0
10.0
49.0
10.0
L
...
12.00
...
14.50
14.50
...
17.50
17.50
...
20.50
20.50
20.50
...
24.50
24.50
24.50
24.50
...
27.00
27.00
27.00
27.00
...
30.00
30.00
30.00
30.00
30.00
...
27.50
27.50
32.00
32.00
32.00
32.00
...
29.50
29.S0
35.00
35.00
35.00
35.00
...
34.50
34.50
34.50
40 50
40.50
40.50
40.50
...
42.0
42.0
42.0
42.0
49.0
49.0
49.0
49.0
49.0
Approximate Weight
Pounds
45
65
75
105
105
115
165
175
200
240
250
275
300
355
370
395
420
460
500
525
555
600
640
655
680
715
755
800
850
860
820
855
895
940
990
1035
800
1095
1130
1170
1220
l400
1345
1180
1200
1250
1810
1890
1950
2040
2020
1790
1830
1875
1910
2765
2820
2895
3045
3285
*Regularly furnished short pattern. Can be made to special order with long body dimensions.
Flange accessories must be ordered separately.
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
67
MJ and Flare
DIMENSIONS AND WEIGHTS
Nominal Dimension
L
Size
Inches
3
8
4
8
6
8
8
10
10
10
12
12
Dimension
C
Inches
7.50
9.00
11.00
13.50
16.00
19.00
Dimension
C
Inches
21.00
23.50
25.00
27.50
32.00
38.75
Flange,
MJ,
Weight Weight
Pounds Pounds
225
...
330
270
355
320
460
410
635
545
760
895
Note: MJ weights are body weights only and do not include weight of mechanical joint accessories.
Dimensions Inches
Nominal
Size
3
4
6
8
10
12
14
16
18
20
24
30
Short Radius
A
5.50
6.50
8.00
9.00
11.00
12.00
14.00
15.00
16.50
18.00
22.00
25.00
D
9.00
10.00
11.50
13.50
16.50
18.50
21.50
23.00
25.00
27.00
32.50
36.00
Approximate Weight
Pounds
Long Radius
C
7.50
9.00
11.00
13.50
16.00
19.00
21.00
23.50
25.00
27.50
32.00
38.75
B
7.75
9.00
11.50
14.00
16.50
19.00
21.50
24.00
26.50
29.00
34.00
...
E
11.25
12.50
15.00
18.50
22.00
25.50
29.00
32.00
35.00
38.00
44.50
...
C
7.50
9.00
11.00
13.50
16.00
19.00
21.00
23.50
25.00
27.50
32.00
...
Short Radius
25
40
70
110
175
245
450
454
675
860
1195
1565
Long Radius
30
50
90
155
230
350
490
700
885
1135
1340
...
Note: End flanges are regularly drilled to 125 pound Standard template on page 52.
68
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
Regular
Reducing Flange
Eccentric
Reducing Flange
REDUCING FLANGES
We can tap for steel or Iron Pipe Size Cast Iron Pipe
Size
Inches
1x6
1 1/4 x 6
1 1/2 x 6
1 1/2 x 7 1/2
2 x 7 1/2
2 1/2 x 7 1/2
1 1/2 x 9
2x9
2 1/2 x 9
3x9
3 1/2 x 9
3 x 10
4 x 10
2 x 11
2 1/2 x 11
3 x 11
4 x 11
5 x 11
3 x 13 1/2
4 x 13 1/2
5 x 13 1/2
6 x 13 1/2
6 x 16
8 x 16
8 x 19
10 x 19
Diameter Bolt
Circle Inches
4 3/4
4 3/4
4 3/4
6
6
6
7 1/2
7 1/2
7 1/2
7 1/2
7 1/2
8 1/2
8 1/2
9 1/2
9 1/2
9 1/2
9 1/2
9 1/2
11 3/4
11 3/4
11 3/4
11 3/4
14 1/4
14 1/4
17
17
Number and
Size of Bolts
4 5/8 x 2 1/4
4 5/8 x 2 1/4
4 5/8 x 2 1/4
4 5/8 x 2 1/2
4 5/8 x 2 1/2
4 5/8 x 2 1/2
8 5/8 x 3
8 5/8 x 3
8 5/8 x 3
8 5/8 x 3
8 5/8 x 3
8 3/4 x 3
8 3/4 x 3
8 3/4 x 3 1/4
8 3/4 x 3 1/4
8 3/4 x 3 1/4
8 3/4 x 3 1/4
8 3/4 x 3 1/4
8 3/4 x 3 1/2
8 3/4 x 3 1/2
8 3/4 x 3 1/2
8 3/4 x 3 1/2
12 7/8 x 3 3/4
12 7/8 x 3 3/4
12 7/8 x 3 3/4
12 7/8 x 3 3/4
Approx. Weight
Pounds
5
5
5
5 1/2
9
9
16
16
16
15
14
19
17
25
24
23
22
21
40
38
36
34
56
50
78
75
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
69
Blind Flange
16-inch O.D. and Smaller
Section
3 thru 10
19-lnch O.D. and Larger
Pounds
Inches
Inches
Pounds
R
T
V
R
T
V
3
7.5 .75 .68
1.0
9
14
21.0 1.37 .87
4
115
4
9.0 .93 .87
1.5
16
16
23.5 1.43 1.0
4
160
5
10.0 .93 .87
1.5
20
18
25.0 1.56 1.12
6
190
6
11.0 1.0 .93
1.5
25
20
27.5 1.68 1.12
6
250
8
13.5 1.12 1.06
2.0
42
24
32.0 1.87 1.25
8
370
10
16.0 1.81 1.12
2.5
63
30
38.75 2.12 1.43
8
620
12
19.0 1.25 .81
3.5
88
...
... ... ...
...
...
* Flanges, 19" O.D. and larger, are regularly furnished dished with inside radius equal to port diameter of
pipe size. Flat blind flanges are available when required for tapping.
Maximum tap size shown is for flat blind flange. Maximum tap size for dished blind flange is 2 inches.
See Note
Nominal pipe size Inches Dimension R Inches Dimension T Inches Approximate Weight Pounds
3
5.50
11.00
35
4
6.50
10.00
60
4
7.50
13.00
65
6
7.00
12.00
90
6
8.00
16.00
100
8
9.00
18.00
175
10
11.00
22.00
290
12
12.00
24.00
410
Note: Return bends can be furnished with straight or reducing back outlet. Furnished faced and drilled to
125 pound template.
FLANGE FILLERS
FillersFull Size of Flange
Used for closing up between two flanges which do not meet. Maximum thickness
is six inches; minimum thickness is 3/8 inch.
Fillers
70
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
FLANGE SPECIALS
SPECIAL FLANGE ADAPTER TO CONNECT EXTRA HEAVY 250 POUND FLANGES
AND STANDARD 125 POUND FLANGES
(ANSI B16.1 Spec.)
Common center between flanges are marked and tagged
Flange Adapter
The Flange Adapter is used to connect flanged pipe or fittings with Class 125 flanges to Class 250 flanges
of ANSI B16.1 standard. Common center lines are marked to eliminate difficulty in installaton.
We can furnish pipe or fittings with Class 250 flanges, on special order in limited configurations.
The Flange Adapter is rated for 250 psi water working pressure. Adapters are cast of ductile iron for sizes
3 - 30.
DIMENSION AND WEIGHTS
Nominal Pipe Sizes......Inches
10
12
14
16
18
20
24
30
Length, L ..................Inches
10
12.5
Approximate Weight....Pounds
945
Note: Drilling templates are in multiples of four, so that fittings may be made to face in any quarter.
Bolt holes shall straddle center line.
FOR INFORMATION ONLY
TEMPLATE FOR DRILLING EXTRA HEAVY 250 POUNDS FLANGES
AMERICAN NATIONAL STANDARD SPECIFICATION B16.1 FOR 250 POUND TEMPLATE
For 125 pound template, see page 52
Size
Inches
3
4
6
8
10
12
14
16
18
20
24
30
Diameter
of
Flange
Inches
8-1/4
10
12-1/2
15
17-1/2
20-1/2
23
25-1/2
28
30-1/2
36
43
Thickness
of
Flange
(Min. Inches)
1-1/8
1-1/4
1-7/16
1-5/8
1-7/8
2
2-1/8
2-1/4
2-3/8
2-1/2
2-3/4
3
Diameter
of
Bolt Cirle
Inches
5-11/16
6-15/16
9-11/16
11-15/16
14-1/16
16-7/16
18-15/16
21-1/16
25-5/16
25-5/16
30-5/16
37-3/16
Diameter
of Bolts
Circle
Inches
6-5/8
7-7/8
10-5/8
13
15-1/4
17-3/4
20-1/4
22-1/2
24-3/4
27
32
39-1/4
Number
of
Bolts
8
8
12
12
16
16
20
20
24
24
24
28
Diameter
of
Bolts
Inches
3/4
3/4
3/4
7/8
1
1-1/8
1-1/8
1-1/4
1-1/4
1-1/4
1-1/2
1-3/4
Length
of
Bolts
Inches
3-1/2
3-3/4
4
4-1/2
5-1/4
5-1/2
6
6-1/4
6-1/2
6-3/4
7-3/4
8-1/2
ANSI B16.1 250 pound Ductile Iron Flanges have 1/16" raised face.
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272
71
SLUDGE SHOES
Clow sludge shoes are extra strong, have maximum sludge opening,
and the flare reduces entrance loss to a minimum.
SUCTION STRAINERS
The aggregate area of perforations
is greater than the pipe area.
Flanged End*
Sludge Shoe
Flanged End*
Suction Strainer
Sludge Shoe
Pipe Size
Inches
3
4
6
8
10
12
Dimensions Inches
Laid
Height
12.00
12.00
13.00
14.00
15.00
15.00
Diameter at
Base
5.75
8.00
10.00
12.50
14.50
17.00
Diameter of
Flare
...
8.75
11.00
13.50
15.50
18.00
Floor to
Bottom of the Flare
6.00
6.00
7.00
8.00
8.00
8.00
Approximate Weight
Pounds
25
40
60
85
120
150
Suction Strainer
Pipe Size
O.D. of
Inches
Strainer Inches of
4
7.00
6
9.00
8
13.00
10
15.25
12
17.25
72
Outside Diameter
Inches
6.90
9.05
11.10
13.20
15.30
17.40
Inside Diameter
Inches
5.86
7.91
9.92
11.92
13.92
15.94
630 Linn Street Coshocton, Ohio 43812 (740) 622-6651 FAX (740) 622-4272