Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
(RRFTSMRN°
ROTARY LAWN MOWER
6.5 Horsepower
Power-Propelled
21" Multi-Cut
Model No.
917.377061
• Espahol, p. 20
CAUTION:
Read and follow all
Safety Rules and Instructions
before operating this equipment
If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty
applies for only 90 days from the date of purchase.
Warranty service is available by returning the Craftsman power mower to the nearest Sears
Parts & Repair Center in the United States. This warranty applies only while this product
is used in the United States.
This Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Sears, Roebuck And Co., D/817 WA, Hoffman Estates, II 60179
IMPORTANT: This cutting machine is capable of amputating hands and feet and throw-
ing objects. Failure to observe the following safety instructions could result in serious
injury or death.
ALook for this symbol to point out &WARNING: Battery posts, terminals and
important safety precautions. It means related accessories contain lead and lead
CAUTION!!! BECOME ALERT!!! compounds, chemicals known to the State
YOUR SAFETY IS INVOLVED. of California to cause cancer and birth
AWARNING: In order to prevent ac- defects or other reproductive harm. Wash
cidental starting when setting up, trans- hands after handling.
porting, adjusting or making repairs, _, CAUTION: Muffler and other engine
always disconnect spark plug wire and parts become extremely hot during
place wire where it cannot come in con- operation and remain hot after engine has
tact with plug. stopped. To avoid severe burns on contact,
AWARNING: Engine exhaust, some of its stay away from these areas.
constituents, and certain vehicle compo-
nents contain or emit chemicals known
to the State of California to cause cancer
and birth defects or other reproductive
harm.
I. GENERAL OPERATION • Always wear safety goggles or safety
• Read, understand, and follow all glasses with side shields when oper-
instructions on the machine and in the ating mower.
manual(s) before starting. Be thoroughly II. SLOPE OPERATION
familiar with the controls and the proper
Slopes are a major factor related to slip &
use of the machine before starting. fall accidents which can result in severe
• Do not put hands or feet near or under
injury. All slopes require extra caution. If
rotating parts. Keep clear of the dis-
you feel uneasy on a slope, do not mow it.
charge opening at all times.
• Only allow responsible individuals, who DO:
are familiar with the instructions, to oper- • Mow across the face of slopes: never
ate the machine. up and down. Exercise extreme caution
• Clear the area of objects such as rocks, when changing direction on slopes.
toys, wire, bones, sticks, etc., which • Remove obstacles such as rocks, tree
could be picked up and thrown by blade. limbs, etc.
• Be sure the area is clear of other people • Watch for holes, ruts, or bumps. Tall
before mowing. Stop machine if anyone grass can hide obstacles.
enters the area.
DO NOT:
• Do not operate the mower when bare-
• Do not trim near drop-offs, ditches or
foot or wearing open sandals. Always
wear substantial foot wear. embankments. The operator could lose
footing or balance.
• Do not pull mower backwards unless
• Do not trim excessively steep slopes.
absolutely necessary. Always look down
• Do not mow on wet grass. Reduced
and behind before and while moving
backwards. footing could cause slipping.
• Never direct discharged material toward III. CHILDREN
anyone. Avoid discharging material Tragic accidents can occur if the operator
against a wall or obstruction. Material is not alert to the presence of children.
may richochet back toward the opera- Children are often attracted to the ma-
tor. Stop the blade when crossing gravel chine and the mowing activity. Never as-
surfaces.
sume that children will remain where you
• Do not operate the mower without last saw them.
proper guards, plates, grass catcher or • Keep children out of the trimming area
other safety protective devices in place. and under the watchful care of another
• See manufacturer's instructions for
responsible adult.
proper operation and installation of • Be alert and turn machine off if children
accessories. Only use accessories ap- enter the area.
proved by the manufacturer. • Before and while walking backwards,
• Stop the blade(s) when crossing gravel look behind and down for small children.
drives, walks, or roads. • Never allow children to operate the
• Stop the engine (motor) whenever you machine.
leave the equipment, before cleaning the • Use extra care when approaching blind
mower or unclogging the chute. corners, shrubs, trees, or other objects
• Shut the engine (motor) off and wait until that may obscure vision.
the blade comes to complete stop before
removing grass catcher. IV. SAFE HANDLING OF GASOLINE
• Mow only in daylight or good artificial Use extreme care in handling gasoline.
light. Gasoline is extremely flammable and the
• Do not operate the machine while under vapors are explosive.
the influence of alcohol or drugs. • Extinguish all cigarettes, cigars, pipes
• Never operate machine in wet grass. and other sources of ignition.
Always be sure of your footing: keep a • Use only an approved container.
firm hold on the handle; walk, never run. • Never remove gas cap or add fuel with
• Disengage the self-propelled mech- the engine running. Allow engine to
anism or drive clutch on mowers so cool before refueling.
equipped before starting the engine. • Never refuel the machine indoors.
• If the equipment should start to vibrate • Never store the machine or fuel contain-
abnormally, stop the engine (motor) and er where there is an open flame, spark
check immediately for the cause. Vibra- or pilot light such as a water heater or
tion is generally a warning of trouble. on other appliances.
3
• Neverfill containersinside a vehicle,on • Keepnuts and bolts, especiallyblade
a truck or trailerbed with a plastic liner. attachmentbolts, tight and keepequip-
Alwaysplace containerson the ground ment in good condition.
awayfrom your vehiclebeforefilling. • Nevertamper with safetydevices.Check
• Removegas-poweredequipmentfrom their proper operationregularly.
the truck or trailer and refuel it on the • Keepmachinefree of grass, leaves,or
ground. If this is not possible,then other debris build-up.Clean oil or fuel
refuel such equipmentwith a portable spillage.Allow machineto cool before
container,ratherthan from a gasoline storing.
dispensernozzle. • Stop and inspectthe equipmentif you
• Keepthe nozzle in contact with the rim strike an object.Repair, if necessary,
of the fuel tank or containeropening at beforerestarting.
all times until fueling is complete. Do • Neverattemptto make wheel height
not use a nozzle lock-opendevice. adjustmentswhile the engine is running.
• If fuel is spilled on clothing,change • Grasscatchercomponentsare subject
clothing immediately. to wear, damage,and deterioration,
• Neveroverfillfuel tank. Replacegas which could expose moving parts or
cap and tightensecurely. allow objectsto be thrown.Frequently
check componentsand replacewith
V. GENERAL SERVICE manufacturer'srecommendedparts,
when necessary.
• Neverrun a machine inside a closed • Mowerbladesare sharp and can cut.
area. Wrap the blade(s)or wear gloves,and
• Nevermake adjustmentsor repairs with use extra caution when servicingthem.
the engine (motor) running.Disconnect • Do not change the enginegovernorset-
the spark plug wire, and keepthe wire ting or overspeedthe engine.
awayfrom the plug to preventaccidental • Maintainor replacesafety and instruc-
starting. tion labels, as necessary.
AWARNING: This lawn mower is equipped with an internal combustion engine and
should not be used on or near any unimproved forest-covered, brush-covered or
grass-covered land unless the engine's exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it
should be maintained in effective working order by the operator.
In the state of California the above is required by law (Section 4442 of the California
Public Resources Code). Other states may have similar laws. Federal laws apply on
federal lands. A spark arrester for the muffler is available through your nearest Sears
Parts & Repair Center (See the REPAIR PARTS section of this manual).
Serial Number:
Date of Purchase:
These accessories were available when this lawn mower was produced. They are not
shipped with your mower. They are also available at most Sears retail outlets and
service centers. Some of these accessories may not apply to your lawn mower.
LAWN MOWER PERFORMANCE
CLIPPING
DEFLECTORS
FOR STABILIZER
REAR DISCHARGE
LAWN MOWERS
GRASS CATCHERS
FOR FOR
REAR DISCHARGE SIDE DISCHARGE
LAWN MOWERS ,_ GRASS
LAWN CATCHERS
MOWERS
Operator MOWING
I POSITION
control bar
Upper
UP handle Vinyl Frame
bindings opening
These symbols may appear on your lawn mower or in literature supplied with the product.
Learn and understand their meaning.
CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL DANGER, KEEP HANDS
OR WARNING ON OFF AND FEET AWAY
Drive
control
- Operator presence control bar
Handle knob
Primer
Grass
catcher
;park plug
Muffler
Mulcher plug
Air filter
Mulcher Wheel adjuster
door (on each wheel)
IMPORTANT: This lawn mower is shipped
WITHOUT OIL OR GASOLINE in the engine.
Operator presence control lever- must Primer- pumps additional fuel from the
be held down to the handle to start the carburetor to the cylinder for use when
engine. Release to stop the engine. starting a cold engine.
Drive control bar - used to engage Starter handle - used for starting engine.
power-propelled forward motion of mower. Mulcher plug - located at the rear dis-
Mulcher door - allows conversion to charge opening. Must be removed when
discharging or bagging operation. 7 converting to bagging operation.
The operationof any lawn , If condition fails to improve after the
mowercan result in foreign above steps (forward speed remains
objects throwninto the the same), your drive belt is worn and
eyes, which can resultin should be replaced.
severeeye damage.Always erator presence control bar
wearsafety glasses or eye shields while
operatingyour lawn moweror performing
any adjustmentsor repairs.We recom-
mend standardsafetyglasses or a wide
vision safety maskworn over spectacles. Drive
HOWTO USEYOUR LAWN MOWER control
TO Ieve r
ENGINE SPEED Adjustment ENGAGE DRIVE
turnbuckle DRIVE CONTROL
The engine speed was set at the facto ry for op- (on underside) CONTROL DISENGAGED
timum performance. Speed is not adjustable.
TO ADJUST CUTTING HEIGHT
ENGINE ZONE CONTROL Raise wheels for low cut and lower wheels
ACAUTION: Federal regulations require for high cut, adjust cutting height to suit
an engine control to be installed on this your requirements. Medium position is
lawn mower in order to minimize the best for most lawns.
risk of blade contact injury. Do not under • To change cutting height, squeeze ad-
any circumstances attempt to defeat the juster lever toward wheel. Move wheel
function of the operator control. The blade up or down to suit your requirements. Be
turns when the engine is running. sure all wheels are in the same setting.
• Your lawn mower is equipped with an NOTE: Adjuster is properly positioned when
operator presence control bar which plate tab inserts into hole in lever. Also, 9-
requires the operator to be positioned position adjusters (if so equipped) allow lever
behind the lawn mower handle to start to be positioned between the plate tabs.
and operate the lawn mower.
LEVER BACKWARD Plate tab
DRIVE CONTROL TO LOWER MOWER
• Self-propelling is controlled by hold-
ing the operator presence control bar
down to the handle and pulling the drive
control lever rearward to the handle.
The farther toward the handle the lever
is pulled, the faster the unit will travel. LEVER FORWARD TO RAISE MOWER Lever
• Forward motion will stop when either
TO ATTACH GRASS CATCHER
the operator presence control bar or
drive control lever are released. To stop 1. Lift the rear door of the lawn mower
forward motion without stopping engine, and place the grass catcher frame side
release the drive control lever only. Hold hooks onto the door pivot pins.
operator presence control bar down 2. The grass catcher is secured to the lawn
against handle to continue mowing mower housing when the rear door is
without self-propelling. lowered onto the grass catcher frame.
NOTE: If after releasing the drive control the ACAUTION: Do not run your lawn mower
mower will not roll backwards, push the mow- without mulcher plug or approved grass
er forward slightly to disengage drive wheels. catcher in place. Never attempt to op-
erate the lawn mower with the rear door
DRIVE CONTROL ADJUSTMENT
removed or propped open.
Over time, the drive control system may be-
come "loose", resulting in decreased speed. ...... Pivot ' Rear
There is a turnbuckle on the underside of the ....._. door Grass
catcher
drive control housing to increase tension on handle
the drive cable. Proceed as follows:
1. Turn unit off and disconnect spark plug
wire from spark plug.
2. Turn nut on underside of drive control
to increase drive speed.
3. Operate mower to test drive speed.
Readjust as required. 8 Catcher frame hook
TO EMPTY GRASS CATCHER
1. Lift up on grass catcher using the
frame handle.
2. Remove grass catcher with clippings
from under lawn mower handle.
3. Empty clippings from bag.
NOTE: Do not drag the bag when emp-
tying; it will cause unnecessary wear.
Grass
catcher Open mulcher door
-_ frame
handle
TO CONVERT MOWER
Your lawn mower was shipped ready to be
used as a mulcher. To convert to bagging
or discharging: Discharge
REAR BAGGING deflector
• Open rear door and remove mulcher
plug. Store mulcher plug in a safe
place.
• You can now install the grass catcher or
optional clipping deflector.
• To convert to mulching or discharging
operation, install mulcher plug into rear
discharge opening of mower.
FOR MULCHING -
SIDE DISCHARGING 1. Rear mulcher plug installed.
• Mulcher plug must be installed into rear 2. Mulcher door closed.
discharge opening of mower. FOR REAR BAGGING -
• Open mulcher door and install dis- 1. Rear mulcher plug removed.
charge deflector under door as shown. 2. Grass catcher installed.
• Mower is now ready for discharging 3. Mulcher door closed.
operation.
• To convert to mulching or bagging FOR SIDE DISCHARGING -
operation, discharge deflector must be 1. Rear mulcher plug installed.
removed and mulcher door closed. 9 2. Discharge deflector installed.
_CAUTION: Do not run your lawn 2. Grasp the white peel tab and pull to
mowerwithout mulcher plug or approved remove the entire seal.
grasscatcher in place. Neverattemptto 3. Screw fuel cap onto fuel tank after fill-
operatethe lawn mowerwith the rear door ing tank with gasoline.
removedor proppedopen. Replace cartridge when empty (about
once a season). Check preserver level
BEFORE STARTING ENGINE
visually.
ADD OIL A DANGER: Cartridge fluid is HARMFUL
Your lawnmower is shipped without oil in OR FATAL IF SWALLOWED. Avoid contact
the engine. For type and grade of oil to to eyes, skin, or clothing. Do not take
use, see "ENGINE" in the Maintenance internally. Do not inhale fluid vapor. Keep
section of this manual. out of reach of children. If swallowed, call
A CAUTION: DO NOT overfill engine with a physician immediately.
oil, or it will smoke heavily from the muffler
ADD GASOLINE
on startup.
1. Be sure lawnmower is level. • Fill fuel tank to bottom of tank filler neck.
2. Remove oil dipstick from oil fill spout. Do not overfill. Use fresh, clean, regular
3. You receive a container of oil with the unleaded gasoline with a minimum of
unit. Slowly pour the entire container 87 octane. Do not mix oil with gasoline.
down the oil fill spout into the engine. Purchase fuel in quantities that can be
NOTE: Initial oil fill requires only 18 oz. used within 30 days to assure fuel fresh-
ness.
due to residual oil in engine from the
manufacturers 100% quality testing. When A CAUTION: Wipe off any spilled oil or
changing oil you may need 20 oz. fuel. Do not store, spill or use gasoline
4. Insert and tighten dipstick. near an open flame.
IMPORTANT: _1_CAUTION: Alcohol blended fuels
• Check oil level before each use. Add oil (called gasohol or using ethanol or metha-
if needed. Fill to full line on dipstick. nol) can attract moisture which leads to
• Change the oil after every 25 hours of separation and formation of acids during
operation or each season. You may storage. Acidic gas can damage the fuel
need to change the oil more often system of an engine while in storage. To
under dusty, dirty conditions. See "TO avoid engine problems, the fuel system
CHANGE ENGINE Oil" in the Mainte- should be emptied before storage of 30
nance section of this manual. days or longer. Empty the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
Engine next season. See Storage Instructions for
oil cap
additional information. Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.
TO STOP ENGINE
• To stop engine, release operator pres-
ence control bar.
Gasoline TO START ENGINE
filler cap
NOTE: Due to protective coatings on the
engine, a small amount of smoke may be
present during the initial use of the prod-
uct and should be considered normal.
10
NOTE: In cooler weather it may be MULCHING MOWING TIPS
necessary to repeat priming steps. In IMPORTANT: For best performance,
warmer weather over priming may cause keep mower housing free of built-up
flooding and engine will not start. If you
grass and trash. See "CLEANING" in the
do flood engine, wait a few minutes before Maintenance section of this manual.
attempting to start and do not repeat
• The special mulching blade will recut the
priming steps.
grass clippings many times and reduce
MOWING TIPS them in size so that as they fall onto the
A CAUTION: Do not use de-thatcher lawn they will disperse into the grass
and not be noticed. Also, the mulched
blade attachments on your mower. Such
grass will biodegrade quickly to provide
attachments are hazardous, will damage
nutrients for the lawn. Always mulch
your mower and could void your warranty.
with your highest engine (blade) speed
• Under certain conditions, such as very
as this will provide the best recutting ac-
tall grass, it may be necessary to raise tion of the blades.
the height of cut to reduce pushing effort
• Avoid cutting your lawn when it is wet.
and to keep from overloading the engine
Wet grass tends to form clumps and
and leaving clumps of grass clippings.
interferes with the mulching action. The
It may also be necessary to reduce
best time to mow your lawn is the early
ground speed and/or run the lawn
afternoon. At this time the grass has
mower over the area a second time.
dried, yet the newly cut area will not be
• For extremely heavy cutting, reduce the
exposed to direct sunlight.
width of cut by overlapping previously • For best results, adjust the lawn mower
cut path and mow slowly. cutting height so that the lawn mower
• For better grass bagging and most cut-
cuts off only the top one-third of the
ting conditions, the engine speed should grass blades. If the lawn is overgrown it
be set in the FAST position. will be necessary to raise the height of
• Pores in cloth grass catchers can be- cut to reduce pushing effort and to keep
come filled with dirt and dust with use
from overloading the engine and leaving
and catchers will collect less grass. To
clumps of mulched grass. For extremely
prevent this, regularly hose catcher off heavy grass, reduce your width of cut
with water and let dry before using. by overlapping previously cut path and
• Keep top of engine around starter clear
mow slowly.
and clean of grass clippings and chaff.
This will help engine air flow and extend
engine life. 1/3
11
MAINTENANCE BEFORE
EACH
AFTER
EACH
EVERY
10
EVERY
25HOURS
EVERY
100
BEFORE
_
Check Tires
Check Drive Wheels /,
Clean Lawn Mower ....
M Clean under Drive Cover *** v'
O Check Drive Belt / Putleys *** v'
W Check / Sharpen / Replace Blade
_ ubrication
Clean and Recharge Battery **
* (if so equipped) 1 _ Change more often if operating under a heavy load or in high outdoor temperatures.
** Electric_Start mowers 2 _ Service more often if operating in dirty or dusty conditions.
*** Power-Propelled mowers 3 - Replace blades more often when mowing in sandy soil.
**** Use a scraper 4 - Charge 48 hours at end of season.
to clean under deck 5 - And after each 5 hours of use.
F -20 0 30 32 40 60 80 100
AIR FILTER
SAE VISCOSITY GRADES
i i i i i
C -30 -20 -10 0 1'0 20 30 40
Cover
Cartridge Cover tabs
MUFFLER
Inspect and replace corroded muffler as it
could create a fire hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of
each mowing season or after every 100
hours of operation, whichever occurs
first. Spark plug type and gap setting
are shown in the "PRODUCT SPECIFIC-
4. Wipe off any spilled oil from lawn ATIONS" section of this manual.
mower or side of engine. 14
CLEANING Keep finished surfaces and wheels free
IMPORTANT: For best performance, keep of all gasoline, oil, etc.
mower housing free of built-up grass and We do not recommend using a garden
hose to clean lawn mower unless the
trash. Clean the underside of your mower
after each use. electrical system, muffler, air filter and
carburetor are covered to keep water
J_CAUTION: Disconnect spark plug wire
out. Water in engine can result in short-
from spark plug and place wire where it ened engine life.
cannot come in contact with plug.
• Clean underside of mower by scraping CLEAN UNDER DRIVE COVER
to remove build-up of grass and trash. Clean under drive cover at least twice a sea-
• Clean engine often to keep trash from son. Scrape underside of cover with putty
accumulating. A clogged engine runs knife or similar tool to remove any build-up
hotter and shortens engine life. of trash or grass on underside of drive cover.
Immediately prepare your lawn mower for "CLEANING" in the Maintenance sec-
storage at the end of the season or if the tion of this manual).
unit will not be used for 30 days or more. , Lubricate as shown in the Maintenance
section of this manual.
LAWN MOWER
3. Be sure that all nuts, bolts, screws, and
When lawn mower is to be stored for a
pins are securely fastened. Inspect
period of time, clean it thoroughly, remove moving parts for damage, breakage
all dirt, grease, leaves, etc. Store in a and wear. Replace if necessary.
clean, dry area. , Touch up all rusted or chipped paint
1. Clean entire lawn mower (See surfaces; sand lightly before painting.
16
HANDLE Alcohol blended fuels (called gasohol or
You can fold your mower handle for storage. using ethanol or methanol) can attract
1. Loosen the two (2) handle knobs on moisture which leads to separation and
sides of the upper handle and allow formation of acids during storage. Acidic
handle to fold down to the rear. gas can damage the fuel system of an
2. Remove the two (2) handle knobs and engine while in storage.
carriage bolts on sides of the lower handle • Empty the fuel tank by starting the en-
and pivot entire handle assembly forward gine and letting it run until the fuel lines
and allow it to rest on mower.
and carburetor are empty.
3. Reinstall knobs and carriage bolts to • Never use engine or carburetor cleaner
lower handle or handle brackets for
products in the fuel tank or permanent
safe keeping. damage may occur.
• When setting up your handle from the • Use fresh fuel next season.
storage position, the lower handle will NOTE: Fuel stabilizer is an acceptable
require manually locking into the mow-
alternative in minimizing the formation of fuel
ing position.
gum deposits during storage. Add stabilizer
IMPORTANT: When folding the handle for
to gasoline in fuel tank or storage container.
storage or transportation, be sure to fold
Always follow the mix ratio found on stabilizer
the handle as shown or you may damage
the control cables. container. Run engine at least 10 minutes
after adding stabilizer to allow the stabilizer to
reach the carburetor. Do not empty the gas
Operator MOWING
tank and carburetor if using fuel stabilizer.
I POSITION
control bar NOTE: FRESH START TM fuel cap and car-
tridge system automatically drips concentrat-
ed fuel preserver into your fuel tank and is an
acceptable alte rnative to adding fuel stabilizer.
FOLD /
/
'"X
/
/
ENGINE OIL
FORWARD",, Upper Drain oil (with engine warm) and replace
FOR ',,, handle with clean engine oil. (See "ENGINE" in
STO RAG E
the Maintenance section of this manual).
CYLINDER
Handle
1. Remove spark plug.
knob
2. Pour one ounce of oil through spark
plug hole into cylinder.
3. Pull starter handle slowly a few times
Lower handle to distribute oil.
4. Replace with new spark plug.
Handle OTHER
bracket
• Do not store gasoline from one season
to another.
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your unit indoors and
cover it to protect it from dust and dirt.
Knob
• Cover your unit with a suitable protective
cover that does not retain moisture. Do
not use plastic. Plastic cannot breathe,
which allows condensation to form and
will cause your unit to rust.
IMPORTANT: Never cover mower while
ENGINE engine and exhaust areas are still warm.
FUEL SYSTEM _CAUTION: Never store the lawn mower
18
TROUBLESHOOTING - See appropriate section in manual unless directed
to a Sears Parts & Repair Center.
PROBLEM CAUSE CORRECTION
19
Garantia ......................................................... 20 Programa de Mantenimiento ......................... 30
Reglas de Seguridad ................................ 20-22 Servicio y Adjustes ................................... 33-34
Especificaciones del Producto ....................... 23 Almacenamiento ....................................... 35-36
Montaje / Pre-Operaci6n ............................... 24 Identificaci6n de problemas ...................... 36-37
Operaci6n ................................................. 25-29 Orden de Partes ....................................... 38-45
Mantenimiento .......................................... 30-32 Servicio Sears .................................. Contratapa
Per dos (2) aSos, a partir de la fecha de compra, cuando esta Segadora Craftsman se mantenga,
lubrique y aline segt3n las instrucciones para la operaci6n y el mantenimiento en el manual del
dueSo, Sears reparar_, gratis rode defecto en el material y la mane de obra.
Si la Segadora Craftsman se usa para fines comerciales o de arriendo, esta garantia s61o se aplica
per noventa (90) dias a partir de la fecha de compra.
Esta Garantia no cubre:
• Articulos que se desgastan durante el use normal tales come las cuchillas segadoras rotatorias,
los adaptadores de la cuchilla, las correas, los filtros de aire y las bujias.
• Reparaciones necesarias debido al abuse o a la negligencia del operador, incluy_ndose a los
cigQe_ales doblados y a la falta de mantenimiento del equipo segt3n las instrucciones que se
incluyen en el manual del dueSo.
El servicio de garantia esta disponible al devolver la segadora a motor Craftsman al Centre de
Servicio Sears mas cercano en los Estados Unidos. Esta garantia se aplica solamente mientras el
producto este en use en los Estados Unidos.
Esta Garantia le otorga derechos legales especificos, y puede que tambi_n tenga otros derechos
que varian de estado a estado.
Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179 USA
IMPORTANTE" Esta maquina cortadaora es capaz de amputar las manes y los manes y los pies y
de lanzar objetos. Si no se observan las instrucciones de seguridad siguientes se pueden producir
lesiones graves o la muerte.
,_ILBusque este simbolo que se_ala las precau- _PRECAUCl6N" El silenciador y otras
ciones de seguridad de importancia. Quiere piezas del motor Ilegan a sre extremadamente
decir- iiiATENClON!!! iiiESTE ALERTO!!! calientes durante la operaci6n y siguen siendo
U SEGURIDAD ESTA COMPROMETIDA. calientes despu_s de que el motor haya parade.
ADVERTENClA: Siempre desconecte el Para evitar quemaduras severas, permanezca
alambre de la bujia y p6ngalo donde no pueda lejos de estas Areas.
entrar en contacto con la bujia, para evitar el
arranque per accidente, durante la preparaci6n,
el transporte, el ajuste o cuando se hacen
_IPAaraclones.
DVERTENClA: Los bornes, terminales y
accesorios relatives de la bateria contienen
plomo o compuestos de plomo, productos
quimicos conocidos en el Estado de California I. OPERACION
come causa de cancer y defectos al nacimiento • Antes de empezar, debe familiarizarse
u otros da_os reproductivos. Lavar las manes completamente con los controles y el use
,_spu_s de manipularlos. correcto de la maquina. Para esto, debe leer
PRECAUClON: El tube de escape del motor, y comprender todas las instrucciones que
algunos de sus constituyentes y algunos com- aparecen en la maquina yen los manuales
ponentes del vehiculo contienen o desprenden de operaci6n.
productos quimicos conocidos en el Estaclo de • No ponga las manes o los pies cerca o
California come causa de cancer y clefectos al debajo de las partes rotatorias. Mantengase
nacimiento u otros daSos reproductivos. siempre lejos de la abertura de la descarga.
20
• Permita que solamente las personas re- • Renueva todos los objetos extra_os, tales
sponsables que esten familiarizadas con las como guijarros, ramas, etc.
instrucciones operen la m_tquina. • Debe prestar atenci6n a hoyos, baches o
• Despeje el Area de objetos tales como piedras, protuberancias. Recuerde que la hierba alta
juguetes, alambres, huesos, palos, etc. que pu- puede esconder obst_.culos.
eden ser recogidos y lanzados por las cuchillas. NO HACER:
• Asegt3rese que el _trea no se hallen per-
• No recorte cerca de pendientes, zanjas o
sonas, antes de segar. Pare la m_.quina si
terraplenes. El operador puede perder la
alguien entra en el Area. tracci6n en los pies o el equilibrio.
• No opere la maquina sin zapatos o con sanda- • No recorte cuestas demasiado inclinadas.
lias abiertas. P6ngase siempre zapatos s61idos.
• No recorte en hierba mojada. La reducci6n en la
• No tire de la segadora hacia atr_ts a menos
tracci6n de la pisada puede causar resbalones.
que sea absolutamente necesario. Mire
II1. NINOS
siempre hacia abajo y hacia detr_ts antes y
mientras que se mueve hacia atr_.s. Se pueden producir accidentes tr_.gicos si el
• Nunca dirigir el material descargado hacia operador no presta atenci6n a la presencia
las personas. Evitar descargar material de los ni_os. A menudo, los ni_os se sienten
contra paredes o barreras. El material puede atraidos por la m_.quina y por la actividad de
retornar al operador. Para la cuchilla cuando la siega. Nunca suponga que los ni_os van a
se pasa por superficies de grava. permanecer en el mismo lugar donde los vio
• No opere la segadora sin los respectivos por t31timavez.
resguardos, las placas, el recogedor de • Mantenga a los ni_os alejados del Area de
cesped u otros aditamentos dise ados para la siega y bajo el cuidado estricto de otra
su protecci6n y seguridad. persona adulta responsable.
• Refi@ase alas instrucciones del fabricante • Est_ alerta y apague la m_tquina si hay ni_os
para el funcionamiento e instalaci6n de que entran al Area.
accesorios. Use t3nicamente accesorios • Antes y cuando este retrocediendo, mire
aprobados por el fabricante. hacia atr_.s y hacia abajo para verificar si hay
• Detenga la cuchilla o las cuchillas cuando cruce ni_os peque_os.
por calzadas, calles o caminos de grava. • Nunca permita que los nifios operen la m_.quina.
• Parar el motor cada vez que se abandona el • Tenga un cuidado extra cuando se acerque
aparato, antes de limpiar la segadora o de a esquinas donde no hay visibilidad, a los
remover residuos del tubo. arbustos, _.rboles u otros objetos que pueden
interferir con su linea de visi6n.
• Apagar el motor y esperar hasta que las
cuchillas esten completamente paradas IV. MANEJO SEGURO DE GASOLINA
antes de remover el receptor de hierba. Usar mucha atenci6n cuando se maneja gaso-
• Segar solamente con luz del dia o con una lina. La gasolina es extremamente inflamable y
buena luz artificial. los vapores son explosivos.
• No opere la m_.quina bajo la influencia del • Apagar todos los cigarrillos, cigarros, pipas y
alcohol o de las drogas. otras fuentes de ignici6n.
• Nunca opere la maquina cuando la hierba • Usar solo un contenedor apropiado.
este mojada. Asegt3rese siempre de tener • Nunca quitar el tap6n de la gasolina o aSadir
buena tracci6n en sus pies; mantenga el carburante con el motor en marcha. Esperarque
mango firmemente y camine; nunca corra. el motor se enffie antes de repostar la gasolina.
• Desconectar el mecanismo de propulsi6n • Nunca repostar la m_tquina al interiorde un local.
aut6noma o el embrague de transmisi6n en • Nunca guardar la m_tquina o el contenedor de
las segadoras que Io tienen antes de poner gasolina donde hay una llama abierta, chispa o
en marcha el motor. luz piloto como una caldera u otros dispositivos.
• Si el equipo empezara a vibrar de una • Nunca Ilenar contenedores en un vehiculo, en
manera anormal, pare el motor y revise de un cami6n o caravana con un forro de pl_.stico.
inmediato para averiguar la causa. General- Colocar siempre los contenedores en el suelo
mente la vibraci6n suele indicar que existe lejos de su vehiculo antes de Ilenar.
alguna avefia. • Quitar equipos que funcionan con gasolina
• Siempre use galas de seguridad o anteojos con del cami6n o caravana y repostar en el suelo.
protecci6n lateral cuando opere la segadora. Si esto no es posible, repostar dicho equipo
II. OPERAOION SOBRE LAS CUESTAS con un contenedor port_.til, m_.s bien que con
Los accidentes ocurren con m_.s frecuencia en una tobera de gasolina.
las cuestas. Estos accidentes ocurren debido a • Mantener la tobera en contacto con el bordo
resbaladas o caidas, las cuales pueden resultar del dep6sito de carburante o de la apertura
en graves lesiones. Operar la recortadora en del contenedor siempre hasta terminar el
cuestas requiere mayor concentraci6n. Si se abastecimiento. No usar un dispositivo de
siente inseguro en una cuesta, no la recorte. cierre-apertura de la tobera.
HAOER: • Si el carburante cae en la ropa que se Ileva,
cambi_trsela inmediatamente.
• Puede recortar a traves de la superficie de
• Nunca Ilenar en exceso el dep6sito de
la cuesta, nunca hacia arriba y hacia abajo.
carburante. Colocar el tap6n de la gasolina y
Proceda con extrema precauci6n cuando apretar de modo seguro.
cambie de direcci6n en las cuestas. 21
V. SERVICIO • Pare e inspeccione el equipo si le pega a un
• Nunca haga funcionar una m_tquina dentro objeto. Rep_.relo, si es necesario, antes de
de un Area cerrada. hacerlo arrancar.
• Nunca haga ajustes o reparaciones mientras • En ningt3n caso hay que regular la altura de
el motor este en marcha. Desconecte el cable las ruedas mientras el motor est,. en marcha.
de la bujia, y mantengalo a cierta distancia de • Los componentes del receptor de la hierba
_sta para prevenir un arranque accidental. van sujetos a desgaste, da_os y deterioro, que
• Mantenga las tuercas y los pernos, espe- pueden exponer las partes en movimiento o
cialmente los pernos del accesorio de la permitir que objetos sean disparados. Controlar
cuchilla, apretados y mantenga el equipo en frecuentemente y cuando sea necesario susti-
buenas condiciones. tuir con partes aconsejadas por el fabricante.
• Nunca manipule de forma indebida los • Las cuchillas de la segadora est_.n afiladas y
dispositivos de seguridad. Controle regular- pueden cortar. Cubrir las hojas o Ilevar guantes,
mente su funcionamiento correcto. y utilizar precauciones especiales cuando se
• Mantenga la m_tquina libre de hierba, hojas u efectt3a mantenimiento sobre las mismas.
otras acumulaciones de desperdicio. Limpie los • No cambie el ajuste del regulador del motor
derrames de aceite o combustible. Permita que ni exceda su velocidad.
la m_.quina se enfrie antes de almacenarla. • Mantener o sustituir las etiquetas de seguridad
e instrucciones, cuando sea necesario.
Estos accesorios estaban disponibles cuando se produjo la segadora. No son facilitados junto al
cortacesped. Tambien est_.n disponibles en la mayoria de las tiendas de Sears yen los centros
de servicio. Algunos de estos accesorios tal vez no se apliquen a su segadora.
RENDIMIENTO DE LA SEGADORA
DESVIADOR
DE RECORTES
ESTABILI- __D ENVASES
PARA SEGADORAS
ZADORES
CON DESCARGA
TRASERA E GASOLINA
RECOREDOR
PARA PARA
SEGADORAS SEGADORAS
CON DESCARGA CON DESCARGA
RECOREDOR
TRASERA LATERAL
MANTENIMIENTO DE LA SEGADORA
ADAPTADORES ACEITE
CORREAS CUCHILLAS DE CUCHILLA RUEDAS DEL MOTOR
22
Acuerdos de Proteccibn para la Reparacibn
Congratulaciones por su buena compra. Su • Ayuda r_pida por tel_fono - soporte tele-
nuevo producto Craftsman® estdt dise_ado f6nico por parte de un tecnico Sears sobre
y fabricado para funcionar de modo fiable por productos que requieren un arreglo en casa,
muchos a_os. Pero como todos los productos, y adem_.s una programaci6n sobre los a
puede necesitar alguna reparaci6n de tanto reglos mas convenientes.
en tanto. En este caso tener un Acuerdo de Cuando se ha comprado el Acuerdo, basta con
Protecci6n para la Reparaci6n puede hacerles una Ilamacla telef6nica para programar el servi-
ahorrar dinero y fastidios. cio. Puede Ilamar cuando quiera, dia y noche o
fijar en linea una cita para obtener el servicio.
Compre ahora un Acuerdo de Proteccidn para Sears tiene m_.s de 12.000 especialistas
la Reparacidn y protegese de molestias y gas- profesionales en la reparaci6n, que tienen
tos inesperados. acceso a mas de 4.5 millones de partes y
accesorios de calidad. Este es el tipo de
Un Acuerdo incluye los puntos siguientes: profesionalidad con que puede contar para
• Servicio experto de nuestros 12.000 espe- ayudar a alargar la vida del producto que acaba
cialistas profesionales en la reparaci6n. de comprar, por muchos aSos. iCompre hoy su
• Servicio ilimitado sin cargo alguno para Acuerdo de Protecci6n para la Reparaci6n!
las partes y la mano de obra sobre todas las Se aplican algunas limitaciones y exclu-
reparaciones garantizadas. siones. Para conocer los precios y tenet
• Sustituci6n del producto si su proclucto m_s informacibn, Ilame al 1-800-827-6655.
garantizaclo no puede ser arreglado. Servicio de Instalaci6n Sears
• Descuento de110% sobre el precio cor- Para la instalacidn profesional Sears de
riente del servicio y de las partes relativas al aparatos de casa, puertas de garaje,
servicio no cubiertas por el acuerdo; tambi_n calentadores de agua y otros importantes
el 10% menos sobre el precio corriente de articulos para la casa, en U.S.A. Ilamar a
un control de mantenimiento preventivo. 1-800-4-MY-HOME®.
Nt_mero de Serie:
Fecha de Compra:
Capacidad y Tipo de Gasolina: 1.6 Cuartos (Regular sin Plomo)
Tipo de Aceite (API SG-SL): SAE 30 (Sobre 32°F); SAE 5W-30 (Debajo 32°F)
Capacidad de Aceite: 20 Onzas
Bujia (Abertura: .030") Champion RJ19LM o J19LM
Torsi6n del Perno de la Cuchilla: 35-40 ft. Ibs.
23
Lea estas instrucciones y el manual completamente antes de tratar de montar u operar su segadora nueva.
IMPORTANTE: Este cortacesped viene SIN ACEITE O GASOLINA en el motor.
Su segadora nueva ha sido montada en la f_.brica con la excepci6n de aquellas partes que se
dejaron sin montar por razones de envio. Todas las partes como las tuercas, las arandelas, los per-
nos, etc., que son necesarias para completar el montaje han sido colocadas en la bolsa de partes.
Para asegurarse que su segadora funcione en forma segura y adecuada, todas las partes y los
articulos de ferreteria que se monten tienen que ser apretados seguramente. Use las herramientas
correctas, como sea necesario, para asegurar que se aprieten adecuadamente.
PARA REMOVER LA SEGADORA DE
LA CAJA DE CARTON
Soporte
1. Remueva las partes sueltas que se incluyen de mango Perno
con la segadora.
2. Cortelasdosesquinasdelosextremosdelacaja
de cart6n y tienda el panel del extremo piano.
3. Remueva todo el material de empaque, ex-
cepto la cuSa entre el mango superior y el
inferior, y la cuSa que sujeta la barra de los
control que exige la presencia del operador Manilla
junto con el mango superior.
4. Haga rodar la segadora hacia afuera de la
caja de cart6n y revisela cuidadosamente
para verificar si todavia quedan partes
sueltas adicionales.
COMO PREPARAR SU SEGADORA
PARA DESDOBLAR EL MANGO
IMPORTANTE: Despliegue el mango con
mucho cuidado para no pellizcar o daSar los
cables de control. PARA MONTAR EL RECOGEDOR DE ClaSPED
1. Levante la secci6n del mango inferior hasta 1. Ponga el bastidor del recogedor de cesped
la posici6n de operaci6n y alinee el agujero en la bolsa del cesped con la parte rigida
en _ste con uno de los tres agujeros para de la bolsa en la parte inferior. Asegt3rese
determinar la altura en el puntal del mango. que el mango del bastidor est_ en el exte-
2. Inserte el perno del mango a traves de este rior de la parte superior de la bolsa.
y del puntal y asegt3relo con la manilla. 2. Deslice los sujetadores de vinilo sobre el
3. Repita el procedimiento para el lado bastidor.
opuesto del mango. AVlSO: Si los sujetadores de vinilo est_tn muy
4. Levante la secci6n del mango superior duros, m_talos en agua caliente por algunos
hasta la posici6n de operaci6n, remueva la minutos. Si se moja la bolsa, d_jela que se
cuSa protectora y apriete las manillas del seque antes de usarla.
mango en forma segura.
Mango del
5. Remueva el material de empaque de alred- bastidor del
edor de la barra de control. recogedor
El mango de la segadora puede ajustarse
segt3n le acomode para segar. Refi_rase a
"AJUSTE DEL MANGO" en la Secci6n de Ser-
vicio y Ajustes de este manual.
POSICION
que sxige la PARA
presencia del SEGAR
operador
LEVANTAR
Suj,
Mango de vinilo ',k. del bastidor
superior
ATTENCION O MOTOR MOTOR R,_,PIDO LENTO ESTRANGU COM- ACEITE PELIGRO, GUARDE LAS
ADVERTENCIA ENCENDIDO APAGADO LACION BUSTIBLE MANOS Y LOS PIES LEJOS
Palanca de
control de Barra de control que exige la presencia del operador
la impulsi6n
Mango del
arrancado[
Cebador
Recogedor
de c_sped
Bujfa
Silenciador
Abra la protecci6n
/i/ _-.,._ Mango del
bastldor del ga
Tap6n
acolchadora PASOS SIMPLES DE RECORDAR
CUANDO CONVIERTA SU SEGADORA
PARA ACOLCHAMIENTO -
SEGADORAS CON DESCARGA LATERAL
1. La plancha acolchadora trasera instalada.
• La tap6n acolchadora debe ser instalada ad- 2. La protecci6n contra la descarga cerrada.
entro de la abertura de la descarga trasera.
• Abra la protecci6n contra la descarga y PARA ENSACAMIENTO TRASERO -
instale el desviador de contra la descarga
1. La plancha acolchadora trasera removida.
debajo de la protecci6n como se muestra.
2. Recogedor del c_sped instalado.
• La segadora esta lista para la operaci6n de 3. La protecci6n contra la descarga cerrada.
la descarga.
• Para convertir a la operaci6n de ensacado PARA DESCARGA LATERAL-
o de descarga, el desviador de la descarga
debe ser removido y la protecci6n contra la 1. La plancha acolchadora trasera instalada.
descarga debe estar cerrada. 2. La desviador de la descarga instalada.
27
_Ib PRECAUClON: No haga funcionar su 2. Agarrar la etiqueta blanca removible y tirar
segadora sin la placa de la acolchadora o sin para quitar el entero precinto.
el recogedor c_sped aprobados en su lugar. 3. Enrocar el tapdn del carburante en el
Nunca trate de operar la segadora cuando se depdsito del carburante despu_s de Ilenar
halla removido la puerta trasera o cuando se el depdsito con gasolina.
ha removido a puerta trasera o cuando est,. un Sustituir el cartucho cuando est,. vacio (aproxi-
poco abierta. madamente uno cada temporada). Controlar
ANTES DE HACERARRANOAR EL MOTOR visualmente el nivel del preservador.
PELIGRO: El fluido del cartucho es
AGREGUE ACEITE DANINO O LETAL SI SE TRAGA. Evitar el
Su segadora rue enviada sin aceite en el motor. contacto con los ojos, la piel o la ropa. No asirlo
Para el tipo y el grado del aceite a utilizar, vea
internamente. No inhalar el vapor del fluido.
el "MOTOR" en la secci6n del Mantenimiento de
este manual. Mantener lejos del alcance de los niSos. Si se
_Jh,PRECAUCl6N: NO sobrellene el motor con traga, Ilamar inmediatamente al m_dico.
aceite, o fumar_t pesa demante del silenciador AGREGUE GASOLINA
cuando Io valla a arrancar. • Llene el estanque de combustible hasta
1. Asegt3rese que la segadora este nivelada. la parte inferior del cuello de relleno del
2. Remueva la varila medidora de aceite del tubo estanque de gasolina. No Io Ilene demasiado.
de desarga de aceite. Use gasolina regular, sin plomo, nueva y lim-
3. Usted recibe un envase de aceite con la pia con el minimo de 87 octanos. No mezcle
unidad. Vierta lentamente el envase entero el aceite con la gasolina. Para asegurar
de aceite en el tubo de relleno del motor. que la gasolina utilizada sea fresca compre
AVlSO" El terrapl_n inicial del aceite requiere estanques los cuales puedan ser utilizados
solamente 18 onzas debido al aceite residual _iLdurante los primeros 30 dias.
en el motor de la prueba de calidad de 100% PREOAUClON: Limpie el aceite o el
del fabricante. AI cambiar el aceite puede combustible derramado. No almacene, derrame
necesitar 20 onzas. o use gasolina cerca de una llama expuesta.
4. Inserte y apriete la varilla medidora de aceite. _I_PREOAUCl6N" Los combustibles mezclados
IMPORTANTE: con alcohol (conocidos como gasohol, o el uso
• Revise el nivel del aceite antes de cada uso. de etanol o metanol) pueden atraer la humedad,
Agregue aceite si es necesario. Llene hasta la la que conduce a la separaci6n y formaci6n de
linea de Ileno en la varilla medidora de nivel. _.cidos durante el almacenamiento. La gasolina
• Cambie el aceite despues de 25 horas de acidica puede daSar el sistema del combustible
operaci6n o una vez por temporada. Puede de un motor durante el almacenamiento. Para
necesitar cambiar el aceite m_ts a menudo
evitar los problemas con el motor, se debe vaciar
cuando las condiciones son polvorosas o su-
cias. Vea "PARA CAMBIAR EL ACEITE DEL el sistema del combustible antes de guardarlo por
MOTOR" en la seccion de Mantenimiento de un periodo de 30 dias o m_.s. Vacie el estanque
este manual. del combustible, haga arrancar el motor y h_.galo
funcionar hasta que las lineas del combustible y el
]-apa del carbu rador queden vacios. La pr6xima temporada
deposito de
aceite use combustible nuevo.Vea las Instrucciones Para
El Almacenamiento para m_.s informaci6n. Nunca
use productos de limpieza para el motor o para el
carburador en el estanque del combustible pues
se pueden producir da_os permanentes.
29
PROGRAMA DE ANTES DESPUES CADA
DE CADA DE CADA 10
CADA
25HORAS O
CADA ANTES DEL
100 ALMACE-
MANTENIMIENTO USO USO HORAS TEMPORADA HORAS NAMmENTO
A Lubricaci6n
T Inspeccionar el Silenciador
Cambiar la Buj[a l_#v
* (si viene equipado) 1 - Cambiar mas a menudo cuando se opere bajo carga pesada o en ambientes con altas temperaturas,
_,-_,-
Segadoras con Arranque EH_ctrico 2 - Dar servicio m_.s a menudo cuando se opere en condiciones sucias o polvorosas.
*** Segadoras con Poder Propulsor 3 - Gamble las cuchillas mAs a menudo cuando siegue en terreno arenoso.
**** UtiHizar una rasqueta para Himpiar 4 - Cargar por 48 horas al fin de la temporada.
debajo de Uacubierta deUcortac6sped 5 =Y despues de 5 horas de funcionamiento.
SILENClADOR
Inspeccione y cambie el silenciador si est,. corroi-
do puede producir un peligro de incendio y/o daSo.
BUJiA
Cambie el bujfa al comienzo de cada tempo-
rada de siega o despu_s de cada 100 horas
de operaci6n, Io que suceda primero. El tipo
de bujia y el ajuste de la abertura aparecen en
"ESPECIFICACIONES DEL PRODUCTO" en la
secci6n de Mantenimiento de este manual.
Envase 32
LIMPIEZA No recomendamos el uso de una manguera
IMPORTANTE: Para obtener el mejor rendimiento, de jardin para limpiar la segadora a menos
mantenga la caja de la segadora sin acumulacion que el sistema electrico, el silenciador, el
de cesped y basura. Limpin la parte de abajo de filtro de aire y el carburador est_n tapados
su segadora despues de cada uso. para evitar que les entre el agua. El agua en
_t, PRECAUCl6N: Desconecte el alambre de el motor puede acortar la duraci6n de este.
la bujia y p6ngalo en donde no pueda entrar en
contacto con esta. LIMPIE DEBAJO DE LA CUBIERTA DE LA
• Limpie la parte inferior de su segadora IMPULSION
rasp_tndola para remover la acumulaci6n de Limpie debajo de la cubierta de la impulsi6n
cesped y basura. por Io menos dos veces cada temporada.
• Limpie el motor a menudo para evitar que Raspe debajo de la cubierta con un cuchillo
se acumule la basura. Un motor tapado fun- para masilla o con una herramienta parecida,
ciona m_.s caliente y se acorta su duraci6n. para remover toda acumulaci6n de cesped o
• Mantenga las superficies pulidas y las rue- basura en la parte inferior de la cubierta de la
das sin gasolina, aceite, etc. impulsi6n.
34
Inmediatamente prepare su segadora para el
almacenamiento al final de cada temporada o si
Soporte
la unidad no se va a usar por 30 dias o m_.s. de mango Perno
SEGADORA
Cuando se va a guardar la segadora por cierto
periodo de tiempo, limpiela cuidadosamente,
remueva toda la mugre, la grasa, las hojas, etc.
Gu_.rdela en un Area limpia y seca.
1. Limpie toda la segadora (Vea"LIMPIEZA"
en la secci6n de Mantenimiento de este Manilla
manual).
2. Lubriquela seg0n se muestra en la secci6n
de Mantenimiento de este manual.
3. Aseg0rese de que todas las tuercas y
clavijas y todos los pernos y tornillos est_n
apretados en forma segura. Inspeccione
las partes que se mueven para verificar si
est_.n daSadas, quebradas o desgastadas.
C_.mbielas si es necesario. MOTOR
4. Retoque todas las superficies que est_n SISTEMA DE COMBUSTIBLE
oxidadas o con la pintura picada; use una IMPORTANTE: Es importante evitar que se
lija antes de pintar. formen dep6sitos de goma en partes funda-
MANGO mentales del sistema de combustible tales
Puede doblar el mango de su segadora para el como el carburador, el filtro del combustible,
almacenamiento. la manguera del combustible o en el estanque
1. Suelte las dos (2) manillas del mango en durante el almacenamiento. Los combustibles
cada lado del mango superior y permita que mezclados con alcohol (conocido como gasohol
el mango se doble hacia detras. o que tienen etanol o metanol) pueden atraer
2. Remueva las dos (2) manillas y los pernos humedad, Io que conduce a la separacion y a la
de cada lado del mango inferior y pivote el formacion de acidos durante el almacenamien-
conjunto entero del mango hacia delante y to. La gasolina acidica puede daSar el sistema
permita le que se descanse sobre la sega- de combustible de un motor durante el periodo
dora. de almacenamiento.
3. Vuelva a poner las manillas y los pernos al • Vaciar el dep6sito del carburante poniendo
mango inferior o a los puntales del mango en marcha el motor y dej_.ndolo funcionar
para la seguridad. hasta que el carburante termine y el
• Cuando prepare su mango a partir de la carburador est_ vacio.
posici6n de almacenamiento, el mango infe- • Nunca use los productos para limpieza del
rior nesecitara cerrarlo manualmente para la carburador o del motor en el estanque de
posici6n de sega. combustible pues se pueden producir daSos
IMPORTANTE: Cuando doble el mango para el permanentes.
almacenamiento o el transporte, asegOrese que • Use combustible nuevo la pr6xima tempo-
Io doble segOn se muestra o purde daSar los rada.
cables de control. AVlSO: El estabilizador de combustible es una
alternativa aceptable para reducir a un minimo
Barra de control POSlCION la formaci6n de dep6sitos de goma en el com-
que exig_ PARA bustible durante el periodo de almacenamiento.
presencia del SEGAR Agregue estabilizador a la gasolina en el
operador estanque de combustible o en el envase para el
almacenamiento. Siempre siga la proporci6n de
mezcla que se encuentra en el envase del esta-
bilizador. Haga funcionar el motor por Io menos
10 minutos despu_s de agregar el estabilizador,
para permitir que este Ilegue al carburador. No
drene la gasolina del estanque de gasolina y el
carburador si se est,. usando estabilizador de
combustible.
AVlSO: El sistema tapdn del carburante y car-
Manilla del tucho FRESH STAR7 _M gotea autom_.ticamente
mango un preservador concentrado de carburante en
el depdsito del carburante yes una acept-
able alternativa a aSadir un estabilizador de
Mango inferior carburante.
35
ACEITE DEL MOTOR • Si es posible, guarde su unidad en un recinto
Drene el aceite (con el motor caliente) y cerrado y c_brala para protegerla contra el
c_.mbielo con aceite de motor limpio. (Vea "MO- polvo y la mugre.
TOR" en la secci6n de Mantenimiento de este • Cubra su unidad con un forro protector
manual.) adecuado que no retenga la humedad. No
ClLINDRO use pl_.stico. El pl_.stico no puede respirar, Io
1. Remueva la bujfa. que permite la formaci6n de condensaci6n,
2. Vade 29 ml (una onza) de aceite a trav_s Io que producir_, la oxidaci6n de su unidad.
del agujero de la bujfa en el cilindro. IMPORTANTE: Nunca cubra la segadora mien-
3. Tire la manilla de arranque lentamente unas tras el motor y las areas de escape to davia
cuantas veces para distribuir el aceite. estan calientes.
4. Cambie por una bujfa nueva. _I_PRECAUCl6N: Nunca almacene la sega-
dora con gasolina en el estanque dentro de un
OTROS edificio en donde los gases pueden alcanzar
• No guarde la gasolina de una temporada a la una llama expuesta o una chispa. Permita que
otra. se enffie el motor antes de alma-cenarla en
• Cambie el envase de la gasolina si se emp- alg_n recinto cerrado.
ieza a oxidar. La oxidaci6n y/o la mugre en
su gasolina producir_.n problemas.
36
SOLUCION DE PROBLEMAS -Vea la seccibn apropiada en el manual amenos que
est_ dirigido a un centro de servico Sears.
PROBLEMA CAUSA CORRECCION
37
CRAFTSMAN ROTARY LAWN MOWER - - MODEL NUMBER 917.377061
14
03
O0
35
18
16
39
4O
31
19
47
CRAFTSMAN ROTARY LAWN MOWER - - MODEL NUMBER 917.377061
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm.
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.
CRAFTSMAN ROTARY LAWN MOWER - - MODEL NUMBER 917.377061
14
\\
\\
\\
16
19
28
6O
43
\ \
19 \ \ \ /z \\
\ ,\ \ f/
57
\ / /
,k \ \ //
\ \
/ /
\
15 \
30
47 22
29 19
19
4O 33
28 33
27 2! 40
33 _2L I 18 20
24
32
21
CRAFTSMAN ROTARY LAWN MOWER - - MODEL NUMBER 917.377061
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm.
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.
BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 123K02-0479-E1
684 8471
V
524
718_
161 lO%
2o_ 22_
42
BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 123K02-0479-E1
977 CARBURETOR
GASKET SET
633A _9
633 _9 p_ 668
61: 276_
445
121 CARBURETOR OVERHAUL KIT
633A 0
-_ 633_
lO4
127
668
231 127 _
975J 137 _
276
117J 276 __ I
43
BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 123K02-0479-E1
969
6081 65
56
55 592_
564_
60
689 _
190_
670
456
597_
304
305
332_
324
46
SERVICE NOTES
47
Your Home
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
iiiiiiiiiiiiiiiiiiii
no matter who made it, no matter who sold it! iiiiiiiiiiiiiiiiiiii
For the replacement parts, accessories and iiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiii
owner's manuals that you need to do-it-yourself. iiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiii
For Sears professional installation of home appliances iiiiiiiiiiiiiiiiiiii
and items like garage door openers and water heaters. iiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiii
1-800-4-MY-HOME ® Anytime, day or night iiiiiiiiiiiiiiiiiiii
(I-800-469=4663) (U.S.A. and Canada) iiiiiiiiiiiiiiiiiiii
www.sears.com www.sears.ca iiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiii
Our Home iiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiii
For repair of carryqn products like vacuums, lawn equipment, iiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiii
and electronics, call or go on-line for the nearest iiiiiiiiiiiiiiiiiiii
Sears Parts and Repair Center. iiiiiiiiiiiiiiiiiiii
iiiiiiiii_
1=800=488-t222 Anytime, day or night (U.S.A. only) iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
www.seal%,com
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
To purchase a protection agreement (U.S.A.) iiiiiiiiiiiiiiiii
or maintenance agreement (Canada) on a product serviced by Sears: iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
1-800-361-6665 (Canada) iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiii
Para pedir servicio de reparad6n Au Canada pour service en fran(_ais: iiiiiiiiiiiiiiiii
a domicilio, y para ordenar piezas:
t-888-SU°HOGAR SM
(1-888_784-6427)
02410