Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
H1 C
pitch Ø
a
Ø5
Ø2
Ø1
D1
Ø3
Ø4
n=
Ø
B
q = 25 Ø + S
Type 1
overall
Ø4 Ø3
n=
Ø/2 6Ø 6Ø S 6Ø 6Ø Ø/2
q = 25 Ø + S
E
Type 2
q1 = 16 Ø + S
overall
q1 = 16 Ø + S
PAGE 1/3
PPC 123/13-02.95
123. FREYSSINET C AND K SYSTEMS ANCHORAGES
K System
ANCHORAGE A’ (TROMPLATE) / ANCHORAGE A (PLATE + TRUMPET)
ANCHORAGE
(4) Ø1int. x e Class 2 55 x 0.45 65 x 0.45 80 x 0.50 100 x 0.60 120 x 0.60 130 x 0.60
(1) K 13 Cement (kg/m) 2.55 3.30 4.80 7.95 11.70 12.15
K 13 Grout (l/m) 1.70 2.20 3.20 5.30 7.80 8.10
(1) K 15 Cement (kg/m) 2.70 3.45 4.95 7.80 11.25 12.15
K 15 Grout (l/m) 1.80 2.30 3.30 5.20 7.50 8.10
Ø2 G 3/4’’ G 3/4’’ G 3/4’’ G 1’’ G 1’’1/2 G 1’’1/2
E 220 270 300 370 590 620
F 110 120 125 125 145 160
CACHETAGE -
a (°) 10 10 10 10 30 30
FIXING
Number of layers 1 1 1 1 2 2
Ø of reinf. bars Steel grade FeE 235 10 12 14 16 14 16
b 160 200 240 300 360 400
s 100 120 150 170 210 240
q1 350 420 500 570 560 640
q2 260 312 374 426 434 496
(3) Jack K 100+ K 200+ K 350+ K 500+ K 700+ K 1000+
or or or or
Multistrand K 100 BH⊗ K 200 BH⊗ K 350 BH⊗ K 500 F ⊗
TENSIONING
Pull-in (mm)
K 13 + = 6 to 9 + = 6 to 9 + = 6 to 9 + = 6 to 9 + = 6 to 9 + = 6 to 9
⊗ = 4 to 6 ⊗ = 4 to 6 ⊗ = 4 to 6
K 15 + = 6 to 11 + = 6 to 11 + = 6 to 11 + = 6 to 11 + = 6 to 11 + = 6 to 11
⊗ = 4 to 8 ⊗ = 4 to 8 ⊗ = 4 to 8 ⊗ = 4 to 8
NOTE
(1) The theoretical quantities must be increased by 10 to 40 % depending on the number of grouting phases.
(2) The helical or cross-wise bursting reinforcing bars given in the table, which oppose the bursting force in the concrete of the anchorage zone, are only valid for an isolated anchorage
in a prismatic section piece (test block), for concrete with a strength fcmin between 23 and 43 MPa (cylinder strength).
– When the anchorages are grouped into one of several lines, continuous reinforcement with an equivalent cross-sectional area must be provided to link all the anchorages, appropriately
anchored within the structure.
(3) All the jacks given in the table correspond to optimal use.
(4) (complying with standard) EN 523.
PAGE 2/3
123. FREYSSINET C AND K SYSTEMS ANCHORAGES
a
Ø pitch
Ø5
Ø2
Ø1
D1
Ø3
h
H1 b/2 one layer b/4
F 3b/8 two layers C
q = 25 Ø + S
Type 1
overall
Ø4 B Ø3
n=4
Ø/2 6Ø 6Ø S 6Ø 6Ø Ø/2
q = 25 Ø + S
E
Type 2
q1 = 16 Ø + S
overall
E
Ø/2 7.5Ø S 7.5Ø Ø/2
q1 = 16 Ø + S
PAGE 3/3