Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
June 2004
The first ML10 lathe left the production line on 14 October 1968, and featured a hardened steel spindle
which ran directly in the cast iron bore of the split headstock bearing.
The first major change came on 18 January 1978, when the headstock was converted to taper roller
bearings from machine No. V137261.
On 4 May 1979, the first Speed 10 lathe, featuring a two-speed countershaft, was launched from machine
No. VS143202M. This was followed a month later on 6 June 1979, by the first long bed machine No.
VSL144264.
The diameter of the threaded RH end of the leadscrew was increased from 5/16’’ BSF to ⅜’’ BSF. All
imperial machines from No. V144354 and all metric machines from No. V144464 had the new screw.
On 11 September 1985 at serial No. 159991, the lathe was fitted with two new raising blocks and a new
countershaft arm. The left hand raising block was extended rearwards to carry the new countershaft arm.
This meant for the first time that the lathe left the factory as a complete machine and no longer needed any
assembly.
From lathe No. V167714M on 25 March 1992, a long cross slide was fitted as standard on all machines.
The Diamond 10 was launched on 27 November 1993. This was the first time that Myford had offered a lathe
direct to the public. The ML10 and Speed 10 lathes were discontinued.
Please Note: When ordering, please state the Serial Number and Prefix Letter of your lathe. This can be
found on the front of the lathe bed at the tailstock end of the machine.
Headstock Section
1
Taper Roller Bearing Headstock continued
Price Excl Price Incl
Part Number Description VAT VAT
73014 Taper Roller Bearing (front) £13.83 £16.25
70/1226 65T Backgear Asembly £48.78 £57.32
70/1227 Backgear Key (included in 70/1226 above) £9.96 £11.70
11163 Special Allen Key £2.42 £2.84
70/1218 Backgear Cluster Assembly 21/56T Gear £22.44 £26.37
A7252 25T Gear £9.50 £11.16
11266 Grubscrew (2BA x ½’’) £0.39 £0.46
33/072 Pack of 10 x 65000 2BA Oil Nipples £6.65 £7.81
A6546 150mm (6’’) dia Faceplate with four slots £22.50 £26.44
11291 Drive Peg for faceplate complete with 11298 washer and
100032 nut £5.05 £5.93
70/1249 Soft centre - 2MT £8.96 £10.53
10372/2 Headstock Vee Cone Pulley Assembly £53.58 £62.96
70032 Headstock Vee Belt £5.76 £6.77
Countershaft Section
Single Speed Countershaft (ML10)
Price Excl Price Incl
Part Number Description VAT VAT
70/1626/6 Three Step Vee Cone Pulley (to headstock spindle) £35.36 £41.55
A6536/1 Countershaft £22.35 £26.26
A2834/1 Oilite Bush £3.05 £3.58
A1832 Countershaft Vee Cone Pulley (from motor drive) £20.79 £24.43
70003 Woodruff Key £0.63 £0.74
A1973 Thrust Washer £0.13 £0.15
70011 Motor drive vee belt for lathes upto serial no. 159990 £8.12 £9.54
70042 Motor drive vee belt for lathes after serial no. 159990 £8.12 £9.54
2
Leadscrew & Apron Section
Price Excl Price Incl
Part Number Description VAT VAT
A7167/1 Leadscrew - Imperial - 8 TPI - Standard bed (without
leadscrew clutch) £71.93 £84.52
A7167/2 Leadscrew - Imperial - 8 TPI - Standard bed (with
leadscrew clutch £71.93 £84.52
10708/1 Leadscrew - Imperial - 8 TPI - Long bed (without leadscrew
clutch) £85.68 £100.67
10708/2 Leadscrew - Imperial - 8 TPI - Long bed (with leadscrew
clutch) £104.06 £122.27
A6510ACC Leadscrew Nut Assembly - Imperial - 8 TPI £25.59 £30.07
10439 Hand Traverse Pinion Assembly - Imperial £14.50 £17.04
A6513 Counter Pinion - Imperial £6.76 £7.94
A6521 Thread Dial Indicator - Imperial £16.72 £19.65
10294/1 Leadscrew - Metric - 3mm pitch - Standard bed (without
leadscrew clutch) £71.93 £84.52
10294/2 Leadscrew - Metric - 3mm pitch - Standard bed (with
leadscrew clutch) £71.93 £84.52
10709/1 Leadscrew - Metric - 3mm pitch - Long bed (without
leadscrew clutch) £85.68 £100.67
10709/2 Leadscrew - Metric - 3mm pitch - Long bed (with leadscrew
clutch) £109.90 £129.13
10295/ACC Leadscrew Nut Assembly - Metric - 3mm pitch £25.59 £30.07
10438 Hand Traverse Pinion Assembly - Metric £17.16 £20.16
10296 Counter Pinion - Metric £6.14 £7.21
10429 Thread Dial Indicator - Metric £15.19 £17.85
10430/1 Thumb Screw £3.27 £3.84
NOTE: On early lathes, the RH end of the leadscrew where the ball handle micrometer dial fits is threaded
5/16’’ BSF. This was later changed to ⅜’’ BSF, which will apply to replacement leadscrews.
Therefore, we suggest you replace the ball handle assembly with A9846 Ball Handle Assembly and the
locknut with A7256/2 Nut.
3
Saddle & Cross Slide Section continued
Price Excl Price Incl
Part Number Description VAT VAT
A7337 Feednut - Metric - 2mm pitch £12.52 £14.71
70/1984A Hard Washer £0.21 £0.25
11257 Fibre Washer £0.16 £0.19
11107 Steel Micrometer Dial (replaces 70/1303 Mazak dial) £15.84 £18.61
or
20/252 Re-settable Micrometer Dial £34.55 £40.60
70/1337 Ball Handle Assembly £17.68 £20.77
11272 Adjusting Screw - Gib strip £1.14 £1.34
11275 Adjusting Screw - Gib strip £1.12 £1.32
100027 Hex. Lock Nut £0.12 £0.14
A6503/1 Gib Strip £1.98 £2.33
70/1311 Adjusting Screw - Saddle gib £2.93 £3.44
100305 Hex. Lock Nut - ¼’’ BSF £0.04 £0.05
A6661 Clamp Pin Assembly £5.07 £5.96
A6518/1 Top Slide £43.62 £51.25
Tailstock Section
Price Excl Price Incl
Part Number Description VAT VAT
A6526 Barrel £35.20 £41.36
70/1506 Barrel Key £6.03 £7.09
70/1520/1 Handwheel Assembly £64.74 £76.07
70/1509 Thrust Plate £4.39 £5.16
70/1248 Hard Centre - 2 MT £10.19 £11.97
11274 Adjusting Screw - Gib strip £0.50 £0.59
A2146 Set Over Screw £1.00 £1.18
4
Plates
Price Excl Price Incl
Part Number Description VAT VAT
33/072 Pack of 10 x 65000 2BA Oil Nipples £6.65 £7.81
A7629 Speed Plate - 50Hz - ML10 only £0.74 £0.87
A7630 Speed Plate - 60Hz - ML10 only £0.74 £0.87
10688 Speed Plate - Speed 10 & Diamond 10 machines £4.07 £4.78
14113 Screwcutting Chart - Imperial machines £9.22 £10.83
10428 Screwcutting Chart - Metric machines £9.22 £10.83
Sundries:
82023 Myford Wall Chart - Wipe clean surface - Decimal
equivalent and pitch tables - extremely useful in workshops £2.05 Nil
15472 ‘New’ Oil Gun £39.00 £37.56
5
Notes:
1. This conversion is only suitable for ML10 lathes fitted with taper roller bearings
in the headstock.
2. We normally recommend ½hp motors on single phase Speed 10 lathes. If your
ML10 is fitted with a 1/3hp motor, you may on occasions, experience a lack of
performance on the highest speed.
3. This conversion set assumes that lathes are already fitted with the current type
raising blocks underneath the bed. If your lathe does not have raising blocks,
please order the following additional items
Price Excl Price Incl
Part Number Description VAT VAT
A7202 Raising Block (1 off) £20.43 £24.01
11865 Left Hand Raising Block and Pivot Bracket (1 off) £78.69 £92.46
100039 Hex. Head Set Screw (4 off) £1.17 £1.37
100005 Washer (4 off) £0.06 £0.07
4. If your lathe is fitted with the old type raising block, i.e. the left hand raising
block does not extend behind the headstock and does not incorporate the cast
lugs on which the countershaft arm is mounted, then pleases add the following
items to your order.
Price Excl Price Incl
Part Number Description VAT VAT
11865 Left Hand Raising Block and Pivot Bracket (1 off) £78.69 £92.46
100039 Hex. Head Set Screw (2 off) £1.17 £1.37
100005 Washer (2 off) £0.06 £0.07
Published by Myford Ltd - Printed in Great Britain - Copyright © 2010 Myford Ltd
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the publishers. Illustrations
are not binding in detail. Design and specification subject to change without notice.
MYFORD LTD
Wilmot Lane, Chilwell Road, Beeston, Nottingham, England
NG9 1ER