Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
F
K
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time: 10 - 20 minutes
● Tools Required for Assembly (not included): Flathead screwdriver , Phillips screwdriver, pliers, electrical
tape, wire cutters, safety glasses &1, 100 Watt, Type - A Medium Base Bulb.
● Helpful Tools (not included): Wire Strippers.
INSTALLATION INSTRUCTIONS
STEP 1: Mounting Screw
Crossbar
a . Screw the Mounting Screws into the Crossbar , place the
Lock Washers over the Mounting Screws and thread the Hex Nut
Hex Nuts onto the Mounting Screws as shown . Secure the
position of the Mounting Screws by tightening the Hex Nuts
against the Crossbar .
b . Secure the Crossbar to the Outlet Box with Outlet Box
Screws . Lock Washer
Outlet Box
Outlet Box Screw
1 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : NF8510K,NF8510TB
STEP 2 :
* Use Wire Connectors ( not supplied ) to connect the WHITE OR RIBBED WHITE OR RIBBED
wires . FROM HOUSE FROM FIXTURE
a . Connect the House Ground Wire to the Fixture Ground
Wire.
b . Connect the House White ( or Ribbed ) Wire to the BLACK ( OR RED ) WIRE BLACK OR SMOOTH
Fixture Supply Wire ( White or Ribbed Side ) .
FROM FIXTURE
c . Connect the House Black ( or Red ) Wire to the Fixture FROM HOUSE
Supply Wire ( Black or Smooth Side ).
d . Wrap each connection with approved electrical tape and
GROUND WIRE GROUND WIRE
carefully stuff all of the connected wires into the Outlet
Box . FROM HOUSE FROM FIXTURE
STEP 3 :
a. Place the Backplate over the Mounting Screws and secure
with Mounting Balls. Hand tighten until snug. Mounting Ball
Mounting Screw
STEP 4 :
a. Install the correct Bulb referring to fixture markings and/or labels for maximum wattage.
STEP 5:
a. Locate the Half Shade over the Backplate and line up holes
on the bottom of the Shade onto the Mounting Holes on the
bottom of the Backplate. Secure the Half Shade by
threading Lock Screws into the Mounting Holes. Hand
tighten until snug.
Half Shade
Backplate
Mounting Hole
Lock Screw
2 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : NF8510K,NF8510TB
STEP 6 :
a . Locate the Half Cover onto the top end of the Half Shade
as shown. Long Screw
b. Locate the Rainproof Washer over the Long Screw and then
place the Long Screw through the holes on Half cover and Half
Shade, thread into the Mounting Hole on the Backplate. Hand Rainproof Washer
tighten until snug.
Half Cover
Mounting Screw
Backplate
Half Shade
STEP 7 :
Refer to following information for caulking instructions:
MOUNTING BALL
With the OUTDOOR FIXTURE properly installed in accordance with supplied Assembly/installation
instructions, proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking.
Using EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were
the FIXTURE BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of
backplate and down other side. DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE to ensure proper
moisture drainage.
3 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : NF8510K,NF8510TB
EXTERIOR GRADE
CAULK
OUTDOOR
FIXTURE BACKPLATE
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
4 OF 4