Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
2 - Check-in Supervision Base Time signals (LED on for 2 sec.) within a 4 minute AUTOMATIC TEMPERATURE
www.paradox.ca. If another lens pattern is ON (default) = hours period, the detector will fall into Energy Save COMPENSATION
required, choose the desired lens and perform OFF = minutes Mode where it will not transmit any alarm These motion detectors are equipped with
the following while referring to Figure 1: signals for approximately 3 minutes. Due to "automatic temperature compensation", which
1. Remove the front cover of the detector (1) For example, to obtain a Check-in Supervision the motion detector’s Alive Software, the red adjusts amplifier gain to maintain coverage
by gently pushing the cover pin (11) in with Timer of 6 minutes, set JP1 = OFF and JP2 = LED will continue to flash to indicate a levels across a wide range of temperatures.
a screwdriver. OFF. detection even when in Energy Save Mode.
2. Pull out the bezel (3) by lightly pressing on Warning: Use the same supervision setting as Once the three-minute Energy Save Mode AUTO PULSE SIGNAL PROCESSING
the bezel pins (4) and (5). in the Omnia Wireless Receiver Module. ends, the motion detector returns to normal Patented Auto Pulse Signal Processing™
3. Remove the lens (2) and replace it with the operation. provides a variable pulse count rate in
alternate lens (Note: when the new lens is JP3 - Sensitivity Setting response to signal shape, strength and width.
properly installed, the grooves should be ON = (Low Sensitivity) In "2-6 mode", the NOTE: If the detector’s cover is removed and The motion detector will immediately generate
inside the bezel and the lens catalogue amount of movement required to generate an then replaced while in Energy Save Mode, the an alarm for very strong signals, or switch
number on top.). alarm is doubled. The use of 2-6 mode is first detection will trigger an alarm signal. automatically to pulse counting as signals
4. Verify that the lens is centered and replace recommended in areas where the incidence of become weaker. The motion detector permits
the bezel by lightly pressing it into place. false alarms may be greater. a very high pulse count rate (up to 6 or
OFF (default) = (High Sensitivity) In "1-3 more) in the presence of low level
SIGNAL STRENGTH TEST mode", you should not be able to cross more signals. Ordinary fixed pulse count
In order to verify the receiver's reception of the than one complete zone (consisting of two motion detectors cannot provide this
motion detector’s signal, perform a signal beams - left and right sensor detecting high pulse count rate due to a heavy
Thank you for choosing the Paradox® strength test as described in the Omnia elements) in the coverage area with any kind loss of detectability at any pulse count
Omnia™ OMN-PMD1 Wireless Motion Wireless Receiver Module’s Reference and of movement. Use this setting for the majority rate higher than 3.
Detector for your professional security Installation Manual before finalizing the of installations.
WARRANTY
applications. You have selected one of the installation of the motion detector. Prior to The Seller warrants its products to be free from defects in
JP4 - Fast/Slow Mode materials and workmanship under normal use for a period
most advanced wireless motion detectors performing the test, make sure the batteries of one year. Except as specifically stated herein, all
ON (default) = "Fast Mode" is recommended express or implied warranties whatsoever, statutory or
available on the market today. Every wireless have been inserted into the battery
for the majority of installations. otherwise, including without limitation, any implied warranty
motion detector is 100% quality-control tested compartment to power the detector. Also verify of merchantability and fitness for a particular purpose, are
OFF = "Slow Mode" is suggested in areas where expressly excluded. Because Seller does not install or
using computerized test equipment, that the motion detector has been assigned to connect the products and because the products may be
the incidence of false alarms may be greater. used in conjunction with products not manufactured by
guaranteeing proper operation and unit a zone according to the instructions in the Seller, Seller cannot guarantee the performance of the
durability. The OMN-PMD1 Wireless Motion Omnia Wireless Receiver Module’s Reference JP5 - LED ON/OFF (see below) security system. Seller obligation and liability under this
warranty is expressly limited to repairing or replacing, at
Detector includes the following features: and Installation Manual. If the transmission is ON (default) = LED activated Seller's option, any product not meeting the specifications.
weak, relocating the transmitter by a few OFF = LED deactivated
In no event shall the Seller be liable to the buyer or any
other person for any loss or damages whether direct or
• Dual rectangular element sensor inches can greatly improve the reception. indirect or consequential or incidental, including without
limitation, any damages for lost profits, stolen goods, or
• Auto Pulse Signal Processing (Patented) RED LED INDICATOR claims by any other party caused by defective goods or
• Auto Temperature Compensation MOUNTING The red LED indicates the following: otherwise arising from the improper, incorrect or otherwise
faulty installation or use of the merchandise sold.
• “No Dead Zone” standard lens Avoid bending, cutting or altering the antenna Note: The warranty does not apply to the alkaline batteries
• Low battery / signal transmission / alarm red or mounting the detector near or on metal as Alarm provided with the unit.
LED indicator this may affect signal transmission. The red LED (9) will illuminate for a period of 2 Auto Pulse Signal Processing:
Patent #5077-549 (U.S.)
• Built-in antenna seconds whenever the motion detector detects Patent #1-302-541 (CAN)
• Tamper switch Corner Mount any kind of movement. LODIFF® lens: Patent #4,787,722 (U.S.)
LODIFF® registered trademark of Fresnel Technologies
• Three “AA” alkaline batteries (included) Carefully remove the PCB by loosening the Inc.
• Range: 500 ft (150m) PCB screw (6) and drill or punch out holes A, Low Battery Omnia is a trademark of Paradox Security Systems.
B, C and D from the back plastic case (see The motion detector performs a battery test *Specifications may change without prior notice. / Les spécifications peuvent changer sans préavis.
© 2002 Paradox Security Systems.
INSTALLATION SITE Figure 3 on reverse side). Screw the back every 12 hours and if a battery voltage of 3.1V
Using a Paradox® standard lens at the plastic case onto the installation site and or less is detected during this test, the red LED
recommended installation height of 7ft (2m) screw the PCB back into place. will flash at 5 second intervals.
±10%, the Omnia OMN-PMD1 will provide full
Flat Surface Mount
coverage from 4ft (1m) to 45ft (14m), without Signal Transmission
Carefully remove the PCB by loosening PCB
any dead zones (see figure 2 on reverse side). The red LED indicator light will blink rapidly
screw (6) and drill or punch out holes E, F, G
When installing transmitters, please be sure when the motion detector transmits a signal to
and H from the back plastic case (see Figure 3
there is at least 1ft (30cm) between each the receiver.
on reverse side). Screw the back plastic case
transmitter and 5ft (2m) between the
onto the installation site and screw the PCB POWERING THE WIRELESS
transmitters and the receiver. Avoid placing
the motion detector in proximity to potential
back into place. DETECTOR
sources of interference such as: reflective Verifying proper polarity, insert three “AA”
JUMPERS alkaline batteries into the motion detector’s
surfaces, direct air flow from vents, fans,
These motion detectors are equipped with four battery compartment (7). To replace the
windows, sources of steam/oil vapor, and
jumpers used to set the operational modes of batteries, remove the old batteries, then press
objects causing temperature changes such as
the motion detector. In the following and release the tamper switch and wait 60
heaters, refrigerators, ovens, and infrared light
instructions, when referring to jumper settings, seconds in order to reinitialize the unit. Insert
sources.
refer to Figure 1 for jumper locations. new batteries while verifying proper polarity.
CHANGING THE LENS Warning: After changing the jumper settings, Warning: After inserting the batteries in the
Warning: Do not touch the sensor surface; replace the cover (1) to close the tamper motion detector, a power-up sequence will
proximité de l’une ou l’autre des sources d’ Montage en coin ON (par défaut) = voyant DEL activé ou conséquents ou accidentels, y compris sans limiter ce qui précède,
les pertes de profits, les biens volés ou des réclamations par des tiers,
interférence suivantes : surfaces réflectives, Retirez avec précaution la plaquette de OFF = voyant DEL désactivé causés par des produits défectueux ou autrement résultant d’une
installation ou usage impropre, incorrect ou autrement défectueux de la
circulation d’air provenant d’un système de circuits imprimés en desserrant la vis (6) et marchandise vendue.
INDICATEUR DEL ROUGE
ventilation, ventilateurs et fenêtres, sources de percez ou transpercez les trous A, B, C et D Note: La présente garantie ne s’applique pas aux batteries au alcalines
vapeur d’eau/vapeur d’huile, source de situés sur le support de plastique (Figure 3). Le voyant DEL rouge indique les états fournies avec cette unité.
réfrigérateurs et les fours. Le voyant DEl rouge (9) s’allumera pendant 2 Technologies Inc.
Montage en saillie secondes aussitôt que le détecteur de Omnia est une marque de commerce de Paradox Security Systems.
Retirez avec précaution la plaquette de mouvement détecte un mouvement. © 2002 Paradox Security Systems.
circuits imprimés en desserrant la vis (6) et