Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Premier Review
SWM History:
DirecTV has been working since Single-Wire multiswitch technology for well over a year.
They began field-testing the SWM multiswitch back in mid-2007. The SWM technology
premiered in a switch form targeted at replacing the frequently used WB-68 switch. The SWM-8
offered users the ability to run 8 tuners, just like the WB-68, without the need to run a separate
wire to each tuner. Installation still required 4 wires from the dish to the switch. There was also
a short-lived SWM-5, which only ran 5 tuners. DirecTV decided not to move forward with producing the SWM-5.
With SWM technology, one could feed 8 basic receivers from one switch and one splitter, or could feed 4
DVR receivers with one switch and one splitter. The great thing about SWM technology, is that the signal can be
split multiple times as well. This means homes pre-wired or switching from cable could use existing wiring by
simply replacing the splitters with higher-bandwith ones if necessary. Additionally, SWM technology feeds two
signals to a DVR receiver without the need for a second wire, and eliminate the need for BBC converters on HD
receivers. The SWM-8 switch includes an OTA port for diplexing antenna signals and two flex-ports for adding
signals from the 72.5 and 95 orbital locations (used for internationals & some locals).
Power Insterter:
The SWM switch requires more power than the receivers provide for traditional LNBs or
switches. DirecTV includes a power inserter with each SWM unit. This simply plugs in to a
standard electrical outlet IN-DOORS and feeds power to the switch or LNB. It has simply two coax
ports, one to the receivers and one to the switch/LNB. The powered-output is colored red and is
labeled SWM, to feed the switch/LNB. The other port is labeled IRD to feed receivers. Reversing
the connections will damage the receivers.
The power inserter generally would be installed near the point where wires enter the home from the dish.
Some users may need to place the power inserter in a different location, due to outlet limiations or the desire to
use a UPS battery-backup. The power inserter can be placed after the splitter as long as the splitter is designed to
pass power to only one port, and the receiver with the power inserter is connected to this port.
Splitters:
Users then ran one or two wires from the switch to anywhere in the home using
traditional coax splitters. Splitters are highly-recomended be rated up to 2300mhz, which are
available at many home-improvement stores such as Lowe’s & Home Depot for around $10. If
the power inserter is placed after the splitter then the splitter must be power-passing to just
one port.
Receiver Compatibility
The SWM technology will only work with newer receivers from the past couple of years. No legacy
receivers will work with the SWM technology. Here is a list of current receivers that work with SWM:
HD-DVRs HD Receivers SD-DVRs Standard Receivers
HR-20 H20 R16 D12
HR-21 H21 R22 D13
Manufacturer Differences:
Closing:
The SWM LNB has been in use by two Satelliteguys members for almost three months and is flawless. The
installation is easy, it is reliable, and eliminates many problems facing installations every day, such as limitations in
pre-wired homes. The change reduces coax feeds, installation time, and makes it easier to expand post-install.
DirecTV started rolling SWM LNBs out to HSP installers in May 2008, and it is expected to be a mainstream
installation method by 2009. The SWM-8 is not going away, as some installs will still require capabilities the SWM
LNB can’t handle. These include international or side-dish locals, legacy receivers, and MDU installs.
This technology is well worth the wait, and DirecTV has a real winner in the SWM LNB. No cost data is
available yet, but the SWM-8 is selling for around $300 through MDU distributors. It is reasonable to expect the
price of the SWM LNB to be similar to the SWM-8 as it first becomes available, and to go down as they become
mainstream equipment.