Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Time Remaining:
Bottom of Form
Top of Form
Page:
Showing 3 of Next 3 <Prev
4 >
GO
Bottom of Form
31 Top of Form
Refer to the exhibit. All routers are configured for OSPF area 0. The network administrator requ
that R2 always be the DR and maintain adjacency.
224.0.0.6
224.0.0.9
224.0.0.10*****
Bottom of Form
33 Top of Form
Refer to the exhibit. What summary address can Router2 advertise to Router1 to reach the thre
networks on Routers 3, 4, and 5 without advertising any public address space or overlapping th
networks on Router1?
172.16.0.0/8
172.16.0.0/10
172.16.0.0/13******
172.16.0.0/20
172.16.0.0/24
Bottom of Form
34 Top of Form
Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes do
Which statement is true regarding how the routers in this topology will respond to this event?
Router5 flushes the unreachable route from its routing table in 30 seconds.
Router4 will learn about the failed route 30 seconds later in the next periodic update.
Router5 will send Router4 a triggered update with a metric of 16 for network***
Split horizon will prevent Router4 from fowarding packets to the 10.0.0.0 network until the
holddown timer expires.
Bottom of Form
35 Top of Form
Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What ar
two results of this command? (Choose two.)
A static route will be updated in the routing table.*****
The route will be specified as the default route for all networks not defined in*
All the broadcasts will be forwarded via the S0/0/0 interface of R2.
Bottom of Form
36 Top of Form
Which two statements are true regarding link-state routing protocols? (Choose two.)
They are aware of the complete network topology.****
They offer rapid convergence times in large networks.****
They do not work well in networks that require special hierarchical designs.
They pass their entire routing tables to their directly connected neighbors only.
Bottom of Form
37 Top of Form
A network technician must reduce the amount of broadcast traffic on the network while maintai
connectivity between all different network segments. Which device should the administrator de
hub
Router***********
Layer 2 switch
multiport repeater
Bottom of Form
38 Top of Form
Refer to the exhibit. An administrator is attempting to configure a router by copying and pasting
commands that are shown in the exhibit. However, only one of the FastEthernet interfaces is co
up. What is the problem?
Both interfaces are in the same IP subnet.********
There can be only one FastEthernet interface enabled on a router at one time.
The administrator did not exit to global configuration mode before configuring FastEthernet
Bottom of Form
39 Top of Form
Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a conso
connection to this router without entering a password?
The login command was not entered on the console line.*****
40 Top of Form
What are two tasks that must be completed before two routers can use OSPF to form a neighb
adjacency? (Choose two.)
The routers must elect a designated router.
41 Top of Form
Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The routes of a
routers are displayed. All routers are operational and pings are not blocked on this network.
from R1 to 192.168.3.1*****
from R2 to 192.168.1.1
from R2 to 192.168.3.1
Bottom of Form
42 Top of Form
Refer to the exhibit. RTB is assigned Priority 10 and all other routers use the default priority set
How will OSPF select the DR on network 10.10.8.4/30?
The router with the highest priority will become the DR.
The router with the highest IP address will become the BDR.
The router with the highest loopback address will become the DR.
Bottom of Form
43 Top of Form
Refer to the exhibit. A network administrator is troubleshooting the OSPF network. The 10.10.0
network is not showing up in the routing table of Router1. What is the probable cause of this pr
The serial interface on Router2 is down.
There is an incorrect wildcard mask statement for network 10.10.0.0/16 **on Router2.
Bottom of Form
44 Top of Form
The network shown in the diagram is having problems routing traffic. It is suspected that the pr
is with the addressing scheme. What is the problem with the addressing used in the topology?
The address assigned to the Ethernet0 interface of Router1 is a broadcast address for that
subnetwork.
The subnetwork configured on the serial link between Router1 and Router2 overlaps with th
subnetwork assigned to Ethernet0 of Router3.*****
The subnetwork assigned to the Serial0 interface of Router1 is on a different subnetwork fr
address for Serial0 of Router2.
The subnetwork assigned to Ethernet0 of Router2 overlaps with the subnetwork assigned t
Ethernet0 of Router3.
Bottom of Form
45 Top of Form
Refer to the exhibit. Routers R1 and R3 use different routing protocols with default administrati
distance values. All devices are properly configured and the destination network is advertised b
protocols.
Which path will be used to transmit the data packets between PC1 and PC2?
The packets will travel via R2-R1.********
The traffic will be load-balanced between two paths — via R2-R1 and via R2-R3.
The packets will travel via R2-R3, and the other path via R2-R1 will be retained as the back
path.
Bottom of Form
Top of Form
Page:
Showing 3 of Next 3 <Prev
4 >
GO
Bottom of Form
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy
Statement and Trademarks
Top of Form
Bottom of Form