Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1 Description
These two−stage 2/2 solenoid operated directional seat val- in certain mobile and industrial applications where leak−tight
ves, series WR22G / WR22O, are size 16 high perfor- shut−off functions are crucially important. Examples are
mance screw−in cartridges with an M42x2 mounting thread where loads, tensions, or clamping forces must be held wi-
for cavity type EB, which conforms to ISO 7789. The main thout leakage. All external parts of the cartridge are zinc pla-
and pilot stages are designed on the poppet/seat principle ted and chromited (CrVI−free) and are thus suitable for use
and the 2 → 1 flow path is therefore virtually leak−free. De− in the harshest operating environments. The slip−on coils
energised closed" and de−energised open" functions are can be replaced without opening the hydraulic envelope
available. In addition, these solenoid operated seat valves and can be positioned at any angle through 360°. If you in-
can be supplied with a low−watt coil (nominal power con- tend to manufacture your own cavities or are designing a
sumption 8 W). The straightforward design delivers an out- line−mounting installation, please refer to the section Rela-
standing price/performance ratio and good pressure/flow ted data sheets".
ratings. These screw−in cartridges are predominantly used
2 Symbol
2 2
1 1
WR22G WR22O
3 Technical data
Reference: 400−P−150121−E−01/09.07
Classification: 430.300.−.305.330.300 1/4
Hydraulic characteristics Description, value, unit
Maximum operating pressure (ports 1 and 2) 420bar
Maximum flow rate 350l/min
Flow direction 1 → 2 / 2 → 1, see symbols
Hydraulic fluid HL and HLP mineral oil to DIN 51 524;
for other fluids, please consult BUCHER
Hydraulic fluid temperature range −25°C +80°C
Viscosity range 10500mm 2/s (cSt), recommended 15...250mm2/s (cSt)
Minimum fluid cleanliness class 20/18/15
Cleanliness class to ISO 4406:1999
4 Performance graphs
measured with oil viscosity 33mm2/s (cSt), coil at steady−state temperature and 10 % undervoltage
p = f (Q) Performance limits
p [bar]
P0072.ai
420
300
200
100
0
0 50 100 150 200 250 300 350 Q [l/min]
Δp = f (Q) Pressure drop − Flow rate characteristic Δp = f (Q) Pressure drop − Flow rate characteristic
with annular groove in cavity type EB without annular groove in cavity type EB
p [bar] p [bar]
P0075.ai P0076.ai
25 25 1 2
20 20
1 2
15 15 2 1
10 10
2 1
5 5
0 0
0 50 100 150 200 250 300 350 Q [l/min] 0 50 100 150 200 250 300 350 Q [l/min]
400−P−150121−E−01/09.07 2/4
Series WR22G,WR22O
5 Dimensions & sectional view
63.4
56.4 7
Ø 36
WSP22...
73
102
24
Ma = 40 ± 2 [Nm]
6
46
175
29
Ma = 200 ± 10 [Nm]
Ø 49
1
M42 x 2
4
2
73
4
2
5
3
5
1
6 Installation information
Important NBR seal kit no. DS−351−N 2)
When fitting the cartridges, use the specified Item Qty. Description
tightening torque. No adjustments are necessary,
1 1 O−ring no.129 ∅39,34x 2,62 N90
since the cartridges are set in the factory.
2 1 O−ring no.125 ∅32,99x 2,62 N90
3 1 O−ring no.124 ∅31,42x 2,62 N90
Attention
4 2 Backup ring ∅32,00x2,00x1,40 FI0751
Only qualified personnel with mechanical skills
may carry out any maintenance work. Generally, 5 2 Backup ring ∅30,00x2,00x1,40 FI0751
the only work that should ever be undertaken is to 6 1 NBR seal kit no. DS−246−N for WSP22
check, and possibly replace, the seals. When
changing seals, oil or grease the new seals thor- Important
oughly before fitting them. 2) Seal kit with FKM (Viton) seals, no. DS−351−V
400−P−150121−E−01/09.07 3/4
Series WR22G,WR22O
7 Ordering code
W = directional valve
R = check valve function, seated design, two stage
22G = 2/2 function, de−energised closed
22O = 2/2 function, de−energised open
N = solenoid operated, VDC = 27 W / VAC = 25 W
L = solenoid operated, VDC = 8 W
B = cavity type EB
A ... Q = standard model − see relevant data sheets
Z ... R = special features − please consult BUCHER
16 = nominal size 16
(blank) = NBR (nitrile) seals (standard)
V = FKM (Viton) seals
(special seals − please consult Bucher)
1 ... 9 = design number (omit when ordering new units)
... = voltage and current plainly specified
(blank) = ISO 4400 / DIN 43 650 mating plug (standard, IP65)
M100 = without mating DIN plug
for the following plug variants with 8W coils, please consult Bucher:
C = Kostal plug connection (IP65)
JT = Junior Timer radial plug connection (with quenching diode, IP65)
IT = Junior Timer axial plug connection (with quenching diode, IP65) mating plug not supplied
D = Deutsch plug connection DT04−2P (IP 67)
DT = Deutsch plug connection DT04−2P (with quenching diode, IP 67)
F = flying leads (500 mm)
info.ch@bucherhydraulics.com www.bucherhydraulics.com
E 2007 by Bucher Hydraulics AG, CH−3714 Frutigen
All rights reserved.
Data is provided for the purpose of product description only, and must not be considered as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
400−P−150121−E−01/09.07 4/4
Series WR22G,WR22O