Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Solution
Support
About Us
FAQs
How to configure the internet access service on GPON OLT P1201?
How to configure the internet access service on GPON OLT P1201?
10-23-2020
1043
Note: This Article Applies to: TP-Link GPON OLT P1201 Ver.1;
All the service is based on the Data Plan, so before we start the configuration, we need to make a Data Plan first. The Data Plan is a table which describe all kinds of
service providing. Here we will take the following Data Plan as example to show how to configure the OLT device to provide the Internet access service.
Data Plan
Service Classification Data
Profile ID:10
Profile Type:Type3
Assured Bandwidth:8Mbit/s
Maximum Bandwidth :
DBA Profile 20Mbit/s
Profile ID:10
T-CONT ID:1
Internet access service GEM
ONT Line Profile Port ID:11
Service Profile:10
ONT Service Profile ONT Capacity:adaptive
PON Port:4
Network Data ONT ID:1
GPON ONT profiles include the DBA profile, line profile, service profile, traffic profile.
xx. DBA profie: A DBA profile describes GPON traffic parameters. A T-CONT is bound to a DBA profile for dynamic bandwidth allocation, improving
upstream bandwidth utilization.
xx. Line profie: A line profile describes the binding between the T-CONT and the DBA profile, the QoS mode of the traffic stream, and the mapping between
the GEM port and the ONT side service.
xx. Service profie: A service profile provides the service configuration channel for the ONT that is managed by using optical network terminal management
and control interface (OMCI).
We will follow the below process to finish the configuration:
Step1. Create global vlans.
According to the data plan, we will need a vlan to transmit the Internet access services.
OLT(config)# vlan 100
Step2. Configure the OLT uplink port.
The uplink port of the OLT is the one connected to the service provider. You need to add the uplink port to the VLAN we just created, and set the port type according
to the requirement. Here we add GE9 port to the VLANs as the uplink port.
OLT(config)# interface ge 0/0
OLT(interface-ge)# vlan mode 9 hybrid
OLT(interface-ge)# vlan hybrid 9 tagged 100
OLT(interface-ge)#exit
Step3. Create the DBA profile.
Run the show dba-profile command to query existing DBA profiles in the system. If the existing DBA profiles in the system do not meet the requirements, run
the dba-profile command to add a DBA profile.
Create the same DBA profile for different types of services. Set the profile ID to 10, profile type to type3, assured bandwidth to 8 Mbit/s, and maximum bandwidth to
20 Mbit/s.
OLT(config)# dba-profile profile-id 10
OLT(dba-profile-0)# type3 assure 8192 max 20480
OLT(dba-profile-0)# commit
Note: The DBA implementation is based on an ONT. Therefore, select a DBA profile of the proper bandwidth type and configure proper bandwidth according to the
service types and total user count of the ONT. There are 5 kinds of dba-profile types, please refer to the User Guide to check the details.
Step4. Create ONT Line Profile.
The ont-lineprofile describes the binding relationship between the T-CONT and the DBA template, the QoS mode of the service flow, and the mapping between the
GEM Port and the ONT side. It is mainly used to configure DBA, T-CONT, and GEM Port related information.
Create a GPON ONT line profile, ID is 10, and bind T-CONT 1 to the DBA profile 10 in this line profile. We map the gem port 11 to VLAN 100.
OLT(config)# ont-lineprofile profile-id 10
OLT(ont-lineprofile-10)# tcont 1 dba-profile-id 10
OLT(ont-lineprofile-10)# gem add 11 tcont 1
OLT(ont-lineprofile-10)# gem mapping 11 1 vlan-id 100
OLT(ont-lineprofile-10)# commit
OLT(ont-lineprofile-10)# exit
Step5. Create ONT Srvprofile.
Use the ont-srvprofile command to create and enter the GPON ONT service profile mode or enter the created GPON ONT service profile mode. The ONT service-
related attributes are configured in the service template.
OLT(config)# ont-srvprofile profile-id 10
OLT(ont-srvprofile-10)# ont-port eth adaptive pots adaptive catv adaptive
OLT(ont-srvprofile-10)# commit
OLT(ont-srvprofile-10)# exit
Step6. Add the ONT to OLT.
Only when the ONT register to the OLT successfully, you can configure the service of the ONT. We connect the ONT to PON4 port, SN is DB1920223344. Bind it to
ONT line profile 10 and ONT service profile 10.
OLT(config)# interface gpon 0/0
OLT(interface-gpon)# ont autofind 4 enable
OLT(interface-gpon)# show ont autofind 4 all
//Uses this command to display all the ONT connected on that PON port.
OLT(interface-gpon)# ont add 4 1 sn-auth DB1920223344 ont-lineprofile-id 10 ont-srvprofile-id 10
Add pon 4 onu 1 successfully.
Step7. Configure the service-port.
After registering to the OLT successfully, we need to configure the PON port. For example, if we connect the ONU at PON4, we also need to add the PON4 into the
VLAN we just created.
OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)# ont port native-vlan 4 1 eth 1 vlan 100
OLT(config-interface-gpon-0/0)# exit
OLT(config)# service-port 3 vlan 100 gpon 0/0 port 4 ont 1 gemport 2 multi-service user-vlan 100 tag-action transparent
Step8. Save Configuration.
Remember to save the configuration we just made.
OLT(config)# save
B: EMS
Step1. Create VLAN
Please log in the EMS, and click Switch Control Card to open the switch management page. Then go to Port VLAN ManagementàVLAN list. After creating
VLAN, we need to add the corresponding port into it. Here we add the uplink port into VLAN 100.
Then we need to change the port type. Go to Port VLAN Config. Click the Config to change the Port from Access to Hybrid.
Company
About Us
Contact Us
Products
Wi-Fi Router
Home Wi-Fi System
VDSL
GPON
LTE Router
LTE MiFi
Press
News & Events
Insights
Worldwide / English
Copyright © 2021 TP-Link Corporation Limited. All rights reserved.