Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
active subwoofer
active subwoofer 119SA
ATTENZIONE Introduzione 3
Nell'interesse della propria e della altrui sicurezza, e per non
__________________________________________
invalidare la garanzia, si raccomanda una attenta lettura di Descrizione 3
questa sezione prima di adoperare il prodotto. __________________________________________
- Questo apparecchio è stato progettato e costruito per venire utilizzato
__________________________________________
Pannello controlli e connessioni 4
come sistema di altoparlanti con amplificatore nel contesto tipico di un __________________________________________
sistema di amplificazione sonora e/o di un sistema di registrazione sonora.
Collegamenti 5-6
L'utilizzo per scopi diversi da questi non è contemplato dal costruttore, ed __________________________________________
avviene pertanto sotto la diretta responsabilità dell'utilizzatore/installatore.
Importante !!! 7
PER EVITARE IL RISCHIO DI INCENDIO E/O DI FOLGORAZIONE: __________________________________________
• Non esporre il prodotto alla pioggia, non utilizzarlo in presenza di eleva-
Appendix 14 - 21
ta umidità o vicino all'acqua. Non lasciare penetrare all'interno dell'appa- __________________________________________
recchio alcun liquido, né alcun oggetto solido. In caso ciò avvenga, scollega-
re immediatamente l'apparecchio dalla rete elettrica e rivolgersi ad un ◗ Dati tecnici 15
servizio di assistenza qualificato prima di adoperarlo nuovamente.
__________________________________________
• Prima di collegare l'apparecchio alla rete elettrica assicurarsi che la tensio- ◗ Connettori 16
ne corrisponda a quella indicata sull'apparecchio stesso. __________________________________________
• Collegare questo apparecchio esclusivamente ad una presa di corrente ◗ Esempio di collegamento 1 17
dotata di contatto di terra, rispondente alle norme di sicurezza vigenti, tra- __________________________________________
mite il cavo di alimentazione in dotazione. Nel caso in cui il cavo necessiti
di sostituzione, utilizzare esclusivamente un cavo di identiche caratteristiche. ◗ Esempio di collegamento 2 18
__________________________________________
• Non appoggiare alcun oggetto sul cavo di alimentazione. Non posarlo
dove possa costituire intralcio e causare inciampo. Non schiacciarlo e non ◗ Esempio di collegamento 3 19
calpestarlo.
__________________________________________
• Installare questo apparecchio prevedendo ampio spazio circostante per ◗ Esempio di collegamento 4 20
un'abbondante circolazione d'aria, necessaria al raffreddamento. __________________________________________
Non ostruire le aperture o le prese d'aria presenti sull'apparecchio.
◗ Schema a blocchi 21
• In caso di sostituzione del fusibile esterno, utilizzare esclusivamente un __________________________________________
fusibile di caratteristiche identiche, come riportato sull'apparecchio.
◗ Parti di ricambio 21
• Prima di effettuare qualsiasi operazione di collegamento, assicurarsi che __________________________________________
l'interruttore di accensione dell'apparecchio sia in posizione 'Off'.
• Prima di effettuare qualsiasi spostamento del prodotto già installato o in
funzione, rimuovere tutti i cavi di collegamento.
• Per scollegare l'apparecchio dalla rete elettrica, non tirare mai lungo il
cavo, ma afferrarlo sempre per il connettore.
ATTENZIONE!
Questo apparecchio non contiene parti interne destinate all'inter-
vento diretto da parte dell'utilizzatore. Per evitare il rischio di
incendio e/o folgorazione, non aprirlo. Per qualsiasi intervento
di manutenzione o riparazione, rivolgersi alla Elettronica
Montarbo srl e/o a personale altamente qualificato specificamen-
te segnalato da questa.
- Nel predisporre l'apparecchio all'utilizzo, assicurarsi che la forma e la
portata della superficie di appoggio siano idonee a sostenerlo.
Non tentare mai di appendere il prodotto con mezzi non espressamente
forniti o approvati dal costruttore (corde, catene, funi o qualsivoglia altro
mezzo, attraverso maniglie, bulloni, ganci etc.). Nel caso il prodotto sia
dotato già dalla fabbrica di specifici accessori, verificare sempre, prima
dell'installazione, che il sistema di sollevamento e/o di sospensione che
intendete utilizzare sia di portata idonea al peso del prodotto.
- Per evitare urti, calci, inciampi riservate come luogo per l'istallazione del
prodotto un'area protetta inaccessibile a personale non qualificato.
Qualora l'apparecchio venga utilizzato in presenza di bambini e animali,
si rende necessaria una strettissima sorveglianza.
- Questo prodotto è in grado di generare pressioni acustiche molto
elevate, pericolose per la salute del sistema uditivo. Evitarne quindi l'utilizzo
ad eleva- ti livelli acustici se il pubblico si trova eccessivamente vicino al
prodotto (almeno ad 1 m di distanza). Non esporre i bambini a forti
sorgenti sonore.
ITALIANO 2
active subwoofer 119SA
Introduzione
La cassa bass reflex 119SA, incorpora: Il 119SA è un subwoofer attivo controllato da processore,
progettato per offrire prestazioni eccellenti in tutte le applica-
■ componenti di alta qualità realizzati su zioni ove sia necessaria una maggiore risposta delle frequenze
basse. Un ulteriore vantaggio offerto dall'accoppiamento del
nostre specifiche. 119SA con una cassa acustica di ridotte dimensioni è l'incre-
mento di dinamica ottenibile su tutta la gamma di frequenze,
■ amplificatore Mosfet controllato da poichè non viene più richiesto alle casse e al loro amplificatore
processore (600 W continui, 900 W di picco). di riprodurre le frequenze inferiori ai 100Hz.
La cassa bass-reflex utilizza un woofer da 18" dalla straordi-
naria capacità di escursione, costruito su nostre specifiche.
■ cross-over elettronico stereo.
L’amplificatore incorporato è dotato di un cross-over elettro-
nico a 24dB/oct (100Hz) e di un sofisticato processore che
ottimizzano la linearità della risposta in frequenza ed il
rendimento del sistema.
La straordinaria efficienza acustica e l’estrema semplicità di
installazione rendono il subwoofer attivo 119SA ideale per
l’utilizzo con sistemi di amplificazione di qualsiasi tipo e
marca.
Descrizione
A G
Montarbo 119 SA
ACTIVE SUBWOOFER
C
Montarbo MOD.
POWER
119 SA
600W
POWERED PROCESSOR CONTROLLED
STEREO SUBWOOFER SYSTEM
100Hz 20KHz
GND
E
FLAT
B L
LINK
L
INPUT
L
X-OVER OUT
4 5 6
LIFT
F
3 7
2 8
1 9
0 10
INPUT
R R / mono R LEVEL
FUSE F 5A 230V 50/60Hz
MADE IN ITALY
ITALIANO 3
active subwoofer 119SA
Montarbo MOD.
POWER
119 SA
600W
POWERED PROCESSOR CONTROLLED
STEREO SUBWOOFER SYSTEM
100Hz 20KHz
GND
FLAT
7
LIFT
L L L
5 6
3
2
4
7
8
8
1 9
0 10
INPUT
R R / mono R LEVEL
FUSE F 5A 230V 50/60Hz
MADE IN ITALY
2 5 SOSTITUZIONE FUSIBILE
Fusibile di servizio
Fusibile di riserva
1 Selettore Flat / X-Over. Consente di inviare alle casse 5 Controllo livello ingresso.
acustiche 'satellite', collegate all'uscita stereo (2), il segnale Consente di adeguare la sensibilità di ingresso del finale di
a larga banda o solo la gamma alta. In entrambi i casi il se- potenza incorporato al livello di uscita del mixer.
gnale è dipendente dal controllo di volume (5). Se utilizzate un mixer Montarbo (o comunque un mixer aven-
❚ Pulsante sollevato (crossover disinserito). Condizione 'flat': te livello di uscita 0dB), regolate questo volume al massimo
uscita a 'tutta banda'. (manopola girata in senso orario).
❚ Pulsante premuto (crossover inserito). Condizione 'x-over':
uscita 100Hz÷20kHz del filtro passa alto (100Hz, 24dB/oct.) 6 Commutatore Ground/Lift: disinserisce la massa dell'am-
NOTA: Il pulsante 'flat/x-over' è interno; per commutarlo plificatore dal telaio (pur conservando il collegamento di
servirsi di una punta (penna o matita) quest'ultimo a terra). Consente di ridurre i ronzii prodotti
dai cosiddetti "ground loops" (anelli di massa) quando si
2 2 prese XLR sbilanciate (maschio) per l'uscita stereo. collegano più apparecchi.
4 2 prese XLR bilanciate (maschio): uscite per il collega- 8 Presa di rete con fusibile incorporato.
mento in parallelo di altri subwoofer 119SA o di altri sistemi
attivi.
ITALIANO 4
active subwoofer 119SA
Collegamenti
L’omnidirezionalità delle bassissime frequenze riprodotte dal ci (feedback), con conseguenti inneschi o "code" indesiderate,
119SA (34÷100Hz) rende l’installazione del subwoofer per aumenta a causa della maggiore estensione della risposta in
nulla critica. frequenza.
Pur se è sempre preferibile posizionare il subwoofer vicino Occorre quindi prestare attenzione ed installare il subwoofer
alle casse acustiche, quando necessità di spazio o praticità di su strutture rigide, che non trasmettano vibrazioni ai micro-
montaggio lo richiedano il subwoofer può essere montato foni.
anche a distanza dalle casse stesse (ad esempio: sotto il palco). Qui di seguito verranno descritte alcune tra le configurazioni
Occorre tenere sempre presente che il rischio di rientri acusti- possibili più comuni illustrate alle pagine 17, 18, 19 e 20.
ITALIANO 5
active subwoofer 119SA
Collegamenti
NOTA:
Nei tre esempi illustrati nelle figure 1, 2 e 3 vengono utiliz- È tuttavia possibile che le uscite master del mixer siano già
zate le uscite master L ed R del mixer sia per il collegamento impegnate (ad esempio in un mixer amplificato) ed al posto
al subwoofer (Fig. 1 e 2) sia per il collegamento ai satelliti di queste vengano utilizzate le prese di inserzione.
(Fig. 3) Per il collegamento alle inserzioni è indispensabile cablare i
connettori come illustrato qui di seguito.
CABLARE LA SPINA JACK STEREO COME ILLUSTRATO CABLARE IL CONNETTORE XLR MASCHIO COME ILLUSTRATO
☞
☞
2+
TIP RING GND 12 RING
12
12
12 2 1
12
12
12
3
12
TIP GND
2 1
3GND 1GND
3
☞
ITALIANO 6
active subwoofer 119SA
Importante !
Cura e manutenzione del prodotto: Collegamento alla rete:
• Posizionare la cassa lontano da fonti di calore (caloriferi • Accertarsi che l'interruttore di rete sia spento (0)
o qualsiasi altro oggetto che produca calore).
• Accertarsi che la tensione di rete corrisponda a quella
• Evitare di esporre la cassa alla irradiazione solare diretta, indicata sul pannello (di fianco alla presa di alimentazione).
ad eccessive vibrazioni e ad urti violenti.
• Utilizzare il cavo di alimentazione a tre poli fornito insieme
• Evitare l'uso e il deposito in ambienti polverosi o umidi: alla cassa.
eviterete così cattivi funzionamenti e deterioramento antici-
pato delle prestazioni. • Collegarlo ad una presa di corrente dotata di contatto
di terra.
• Evitare l'uso vicino a fonti di interferenze elettromagneti-
che (video dei monitor, cavi elettrici di alta potenza) ciò
potrebbe compromettere la qualità audio.
Collegamento al mixer:
• Proteggere l'apparecchio dal rovesciamento accidentale di
liquidi o sostanze di qualsiasi tipo. In particolare nelle condi- Se il mixer ha uscite bilanciate XLR:
zioni di utilizzo tipiche, prestare la massima attenzione alla - utilizzare dei normali connettori XLR bilanciati.
collocazione dell'apparecchio onde evitare che il pubblico, i
Se il mixer ha uscite sbilanciate XLR:
musicisti, i tecnici o chicchessia possa poggiare bicchieri,
tazze, contenitori di cibo o di bevande, posacenere o sigaret- - in tal caso, se il mixer non è un Montarbo, è bene accertarsi
te accese sull'apparecchio. che le uscite XLR del mixer siano sbilanciate a norme IEC 268
e cioé: 1 = GND, 2 = HOT, 3 = GND.
• Come asta di sostegno di una cassa satellite si raccomanda
• Prima di effettuare i collegamenti con il mixer, con i
di utilizzare il mod. SM4 Montarbo.
satelliti o con altri sistemi accertarsi che tutti gli interruttori
di rete siano spenti.
• Non togliere la griglia di protezione dalla cassa.
In tal modo si eviteranno fastidiosi rumori e picchi di
segnale talvolta pericolosi per le casse stesse.
• Per rimuovere la polvere usate un pennello o un soffio
d'aria, non usate mai detergenti, solventi o alcool.
ITALIANO 7
active subwoofer 119SA
The lighting flash with arrowhead symbol within an equilateral triangle, is intended
to alert the user to the presence of uninsulated 'dangerous voltage' within the
product's enclosure, that may be of sufficient magnitude to constitute a risk of
electric shock to humans.
The exclamation point within an equilateral triangle, is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions.
ENGLISH
IMPORTANT ! SAFETY INSTRUCTIONS INDEX
WARNING Introduction 9
In order to protect your own and others' safety and to avoid
__________________________________________
invalidation of the warranty of this product, please read this Description 9
section carefully before operating this product. __________________________________________
- This product has been designed and manufactured for being operated as
__________________________________________
Control and connection panel 10
active speaker system in the applications tipical of a sound reinforcement __________________________________________
system or of a sound recording system. Operation for purposes and in
Connections 11 - 12
applications other than these has not been covered by the manufacturer __________________________________________
in the design of the product, and is therefore to be undertaken at end
user's and/or installer's sole risk and responsability. Important !!! 13
__________________________________________
TO AVOID THE RISK OF FIRE AND/OR ELECTRIC SHOCK:
Appendix 14 - 21
• Never expose this product to rain or moisture, never use it in proximity __________________________________________
of water or on a wet surface. Never let any liquid, as well as any object,
enter the product. In case, immediately disconnect it from the mains ◗ Specifications 15
supply and refer to servicing before operating it again.
__________________________________________
• Before connecting this product to the mains supply, always make sure ◗ Connectors 16
that the voltage on the mains outlet corresponds to that stated on the __________________________________________
product.
◗ Connection example 1 17
• This product must be connected only to a grounded mains outlet __________________________________________
complying to the safety regulations in force via the supplied power cable.
In case the power cable needs to be substituted, use exclusively a cable of ◗ Connection example 2 18
__________________________________________
the same type and characteristics.
• Never place any object on the power cable. Never lay the power cable ◗ Connection example 3 19
on a walkway where one could trip over it. Never press or pinch it.
__________________________________________
• Never install the product without providing adequate airflow to cool it. ◗ Connection example 4 20
Never obstruct the air intake openings on it. __________________________________________
• In case the external fuse needs replacement, substitute it only with one ◗ Block diagram 21
of the same type and rating, as stated on the product. __________________________________________
• Always make sure the On/Off switch is in its 'Off' position before doing
◗ Spare parts 21
any operation on the connections of the product. __________________________________________
• Before attempting to move the product after it has been installed,
remove all the connections.
• To disconnect the power cable of this product from the mains supply
never pull the cable directly instead, hold the body of the plug firmly and
pull it gently from the mains supply outlet.
CAUTION!
This product does not contain user serviceable parts.
To prevent fire and/or electrical shock, never remove its cover.
For maintenance and servicing always refer to the official
Montarbo Distributor in your State or to qualified personnel
specifically authorised by the Distributor.
- Before placing the product on a surface of any kind, always make sure
that its shape and load rating will safely match the product's size and
weight. Never attempt to hang the product by any means not expressly
provided or approved by the manufacturer (i.e. ropes, chains, belts or
whatever medium, throgh carring handles, bolts, hooks or whatever).
In case the product is factory-fitted with specific mounting hardware,
always verify before installation that the lifting and/or hanging system
you intend to use is of a proper type and can carry the product weight
with the safety ratio required by the regulations in force.
- To avoid shocks, kicks, or whatever action, always reserve a protected
area with no access to unqualified personnel as installation site of the
product. In case the product is used near children and animals closest
supervision is necessary.
- This product can generate very high acoustic pressures which are
dangerous for the hearing system. Always avoid operation at loud levels
if anyone is excessively near to the product (at least 1 m of distance).
Never expose children to high sound sources.
ENGLISH 8
active subwoofer 119SA
Introduction
The bass reflex enclosure 119SA incorporates: The 119SA is an extraordinary efficient, processor controlled,
active subwoofer specifically designed to enhance the low
■ custom designed, high quality components. frequency response and dynamic range of any speaker system.
One more advantage obtained using the model 119SA with
small size speaker systems is an increased dynamic range on
■ processor controlled MosFet power amplifier the whole frequency spectrum, because the speakers and
(600W continuous, 900 W peak). their amplifiers are no more required to reproduce the low
end (lower than 100Hz) of the audio range.
■ stereo electronic cross-over. The bass reflex enclosure utilizes a 18" custom made woofer
featuring large excursion capability. The built-in power
amplifier is equipped with a 24dB/oct (100Hz) electronic
crossover and a sophisticated processor optimizing the
linearity of the performance of the system.
Its superb performance and ease of installation make of the
119SA the perfect subwoofer addition to essentially any
sound reinforcement system, whatever its type and make.
Description
A G
Montarbo 119 SA
ACTIVE SUBWOOFER
C
Montarbo MOD.
POWER
119 SA
600W
POWERED PROCESSOR CONTROLLED
STEREO SUBWOOFER SYSTEM
100Hz 20KHz
GND
E
FLAT
B L
LINK
L
INPUT
L
X-OVER OUT
4 5 6
LIFT
F
3 7
2 8
1 9
0 10
INPUT
R R / mono R LEVEL
FUSE F 5A 230V 50/60Hz
MADE IN ITALY
ENGLISH 9
active subwoofer 119SA
Montarbo MOD.
POWER
119 SA
600W
POWERED PROCESSOR CONTROLLED
STEREO SUBWOOFER SYSTEM
100Hz 20KHz
GND
FLAT
7
LIFT
L L L
5 6
3
2
4
7
8
8
1 9
0 10
INPUT
R R / mono R LEVEL
FUSE F 5A 230V 50/60Hz
MADE IN ITALY
2 5 FUSE REPLACEMENT
Service fuse
Spare fuse
1 Flat / X-over switch allowing the 'satellite' speaker 5 Input level control.
systems, connected to the stereo output (2), to receive a Allows to adapt the input sensitivity of the built-in power
full-range signal or the upper audio range only. In both amplifier to the output level of the mixer.
conditions the signal is affected by the volume control (5) If you are using a Montarbo mixer (or any other mixer having
❚ Button up (crossover off). 'Flat' mode: the output signal is an output level of 0dB), turn this control fully clockwise to its
'full bandwidth'. maximum setting.
❚ Button pushed (crossover on): 'X-over mode': 100Hz÷20kHz
high pass filter output signal (100Hz, 24dB/oct.). 6 Ground/Lift switch: this switch allows to lift signal ground
NOTE: To avoid misoperation, this button is recessed: use a tip from chassis ground (but the chassis is still connected to the
(pen or pencil) to switch it. safety ground). This allows to lower annoying hums caused
by 'ground loops' when more units are connected.
2 2 unbalanced XLR male sockets for the stereo output.
7 Mains power switch.
3 2 balanced XLR female sockets for the stereo input.
8 I.E.C. power supply socket with built-in fuse.
4 2 balanced XLR male sockets for the 'link' outputs
allowing parallel connection of active speaker systems.
ENGLISH 10
active subwoofer 119SA
Connections
The very low frequency range reproduced by model 119SA range increases the risk of acoustic feedback, with undesired
(34÷100Hz) is essentially omnidirectional allowing easy 'howls' and reduced clarity. It is thus essential to place the
installation of the enclosure. subwoofer on a rigid structure, that does not transmit
In most cases the subwoofer can be placed near the speaker vibrations to the microphones.
systems, but when space or set up reason dictate it, the
subwoofer can be positioned at some distance from them Some connection examples, among the most common
(e.g.: under the stage floor). possible configurations, are described here below and also
You must always consider that the extended low frequency illustrated on pages 17, 18, 19 and 20 of this manual.
ENGLISH 11
active subwoofer 119SA
Connections
NOTE:
Our configuration examples are using the L and R master Take out the signal from the insert sockets by means of a
outputs of the mixer, but if they are already taken up (as, stereo jack plug, in which you have previously joined the
for example, in a powered mixer) the insert sockets can be RING with the TIP and send it to the inputs of the subwoofer
used to the same purposes. by means of an unbalanced XLR, as shown here below.
WIRE THE STEREO JACK PLUG AS SHOWN WIRE THE XLR MALE CONNECTOR AS SHOWN
☞
☞
2+
TIP RING GND 12 RING
12
12
12 2 1
12
12
12
3
12 2 1
TIP GND
3 GND 1GND
3
☞
☞
connect ring with tip connect 1 and 3
(shortcircuit) (shortcircuit)
1 GND = GND
2 + = HOT
INSERT SOCKET 3 - = GND INPUT (XLR FEMALE) OF A
OF THE MIXER. 119SA OR OF A POWERED
SATELLITE SPEAKER
ENGLISH 12
active subwoofer 119SA
Important !
Product Care and Maintenance Power supply connection:
• Never expose the enclosure to heat sources such as radiators • Make sure the 119SA is switched off before starting any
or other products that produce heat. connection.
• Never expose the enclosure to direct sunlight, excessive • Check that mains voltage corresponds to the voltage
vibrations or mechanical shocks. indicated on the panel (beside the main socket).
• Avoid operating and storing the enclosure in dump or dusty • Use the three wire power cord supplied with the enclosure.
places: this will avoid malfunctions, premature degrading of
specifications. • Always connect it to a grounded outlet.
ENGLISH 13
active subwoofer 119SA
APPENDIX
Specifications 15
__________________________________________
Connectors 16
__________________________________________
__________________________________________
Connection example 1 17
__________________________________________
Connection example 2 18
__________________________________________
Connection example 3 19
__________________________________________
Connection example 4 20
__________________________________________
Block diagram 21
__________________________________________
Spare parts 21
__________________________________________
APPENDIX 14
active subwoofer 119SA
Specifications
Speaker system bass reflex
Components: custom designed
- custom woofer 18"high efficiency woofer
Nominal diameter 18"
Nominal impedance 4Ω
Frequency range 32÷2000Hz
Power capacity 1000W
Sensitivity 100dB
Net weight 13,5 Kg
Thiele & Small Parameters
fs 30,8Hz
Re 3,3 Ω
Qms 14,19
Qes 0,20
Qts 0,20
Vas 0,298m3
B.l 22,78T/m
SD 1134cm2
Xmax 5mm
Mms 161,85gr
Le 2.21mH
Impedance 4 ohm
Frequency response 34Hz ÷ 100Hz
Sensitivity (1W / 1m) 100 dB
Max SPL 129 dB
Amplifier MOSFET
Max. output power 600 W
Frequency response 34Hz ÷ 100Hz ±1dB
Input impedance 10KΩ (balanced)
Input sensitivity 0dB (775 mV)
Noise referred to input -110dB (A weighted)
Power supply (Europe and Asia) 230V AC 50÷60Hz
Power supply (USA and Canada) 117V AC 50÷60Hz
Fuse (Europe and Asia) F 5 AL
Fuse (USA and Canada) F 10 AL
Connections
X-over stereo input Balanced female XLRs
Link output (parallel) Balanced male XLRs
X-over stereo output Unbalanced male XLRs
Dimensions (w x h x d): 56 x 65 x 45 cm
Weight 37 Kg
APPENDIX 15
active subwoofer 119SA
Connectors
1 BALANCED CONNECTOR:
2
2 + 1 GND Ground
1 GND 2+ Hot
3- Cold
( standard IEC 268)
3 -
3
BALANCED XLR
MALE CONNECTOR
Montarbo ▲ ▲ MOD.
POWER
119 SA
600W
POWERED PROCESSOR CONTROLLED
2 +
STEREO SUBWOOFER SYSTEM
GND 1
100Hz 20KHz
GND
1 2 2 1 1 2 FLAT
3 3 3
LIFT
- 3 L ▲ L ▲ L
LINK INPUT X-OVER OUT
▲
5 6
BALANCED CONNECTOR: 4
1 2 2 1 1 2 3 7
1 GND Ground 3 3 3 2 8
2+ Hot 1 9
0 10
3- Cold INPUT
R R / mono R LEVEL
( standard IEC 268)
▲ FUSE
MADE IN ITALY
UNBALANCED XLR
MALE SOCKETS
2 +
GND 1 UNBALANCED XLR
FEMALE CONNECTOR
UNBALANCED CONNECTOR:
APPENDIX 16
active subwoofer 119SA
Connection example 1
FIG 1: stereo standard configuration Two 119SA + two powered speaker enclosures 260A
Mixer "L/R" outputs ➟ 119SA "R" inputs
119SA "R" x-over outputs ➟ 260A inputs
Montarbo
2 - WAY
Power Amplifier MADE IN ITALY BY
Montarbo
2 - WAY
PROCESSOR CONTROLLED PROCESSOR CONTROLLED
POWERED SPEAKER SYSTEM POWERED SPEAKER SYSTEM
LEVEL
MOD. 260 A 0 10 LEVEL
MOD. 260 A 0 10
2
2
3
3
1
1
1
1
3
3
2
2
POWER ( P.max 400W ) 230V 50/60Hz FUSE F 2A POWER ( P.max 400W ) 230V 50/60Hz FUSE F 2A
Active subwoofer mod. 119SA
Montarbo MOD.
POWER
119 SA
600W
Montarbo MOD.
POWER
119 SA
600W
POWERED PROCESSOR CONTROLLED POWERED PROCESSOR CONTROLLED
STEREO SUBWOOFER SYSTEM STEREO SUBWOOFER SYSTEM
FLAT FLAT
LIFT LIFT
L L L L L L
LINK INPUT X-OVER OUT LINK INPUT X-OVER OUT
5 6 4 5 6
4
3 7 3 7
2 8 2 8
1 9 1 9
0 10 0 10
INPUT INPUT
R R / mono R LEVEL
R R / mono R LEVEL
FUSE F 5A 230V 50/60Hz FUSE F 5A 230V 50/60Hz
L - R MIXER OUTPUTS
230V
50 60Hz
STEREO EFF. RET. 1 EFF. FT/SW 2
FUSE T
0,5 A
Button PUSHED: x-over mode
☞
L L
(mono)
MIC MIC MIC MIC MIC MIC MIC
1 2 mute mute
A B L R
R R R R R R
0 I
48V D.C.
100Hz 20KHz
LINE LINE LINE LINE LINE LINE LINE MONO AUX OUTPUTS MASTER OUTPUTS CTRL ROOM GND
POWER
L L L L FLAT
INSERT INSERT INSERT
(mono) (mono) (mono) (mono)
1 EFF SEND 2 C AUX SEND D Montarbo
6 7 8 9 10 11 12 13 14 15 16 OUTPUTS LEVEL
GAIN GAIN GAIN GAIN GAIN GAIN GAIN C AUX SEND D
4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6
A B L R LIFT
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8
10 10 10 10 10 10 10 0 10 0 10
9 9 9
L L
6 6 6
HF 2 2 HF 2 2 HF 2 2
HF 2 2 HF 2 2 HF 2 2 HF 2 2
1 4
EXT. EFF. SEND
6 4 6
2 3 3 3
INPUT X-OVER OUT
8 8 8 8 8 8
8 8 8 8 8 8 8 8 2 8 2 8 dB 0 0 0 dB
15 15 15 15 15 15
1.3 1.3 1.3 15 15 15 15 15 15 15 15 0 10 0 10 3 3 3
4 5 6
.75 1.6 .75 1.6 .75 1.6
.3 2 .3 2 .3 2
STEREO DIGITAL 6 6 6
MF 2 2 MF 2 2 MF 2 2 MF 2 2
.18 3 KHz .18 3 KHz .18 3 KHz
EFFECTS PROCESSORS
9 9 9
3 7
MF MF MF 8 8 8 8 8 8 8 8
2 2 2 2 2 2
15 15 15 15 15 15 15 15
E1 12 12 12 2 8
8 8 8 8 8 8
E2
15 15 15
15 15 dB 15 15 dB 15 15 dB LF 2 2 LF 2 2 LF 2 2 LF 2 2
LF 2 2 LF 2 2 LF 2 2 18 18 18
8 8 8 8 8 8 8 8
8 8 8 8 8 8 E1/E2 LOAD
15 15 15 15 15 15 15 15
15 15 15 15 15 15
A 4 6 A 4 6 A 4 6 A 4 6 A 4 6 A 4 6 A 4 6
12 12
2 8 2 8 2 8 2 8 2 8 2 8 2 8 PROGRAMS SELECTOR 9 9
6 6
0 10 0 10 0 10 0 10 0 10 0 10 0 10
3 3
B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 INPUT LEVEL INPUT LEVEL
dB 0 0 dB
3 3 3 3
2 8 2 8 2 8 2 8 2 8 2 8 2 8 6 6
dB 0 dB 0 9 9
0 10 0 10 0 10 0 10 0 10 0 10 0 10 12 12
3 3
C 4 6 C 4 6 C 4 6 C 4 6 C 4 6 C 4 6 C 4 6
10 10
2 8 2 8 2 8 2 8 2 8 2 8 2 8 20 20
0 10 0 10 0 10 0 10 0 10 0 10 0 10
Hz 31 63 125 250 500 1K 2K 4K 8K 16K
D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 4 6 4 6
GAIN 4 6 GAIN 4 6 HF 2 2 HF 2 2
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8
2 8 2 8 8 8 8 8
0 10 0 10 0 10 0 10 0 10 0 10 0 10 flat flat
pre pre pre pre pre pre pre
post post post post post post post on on 10 10 15 15 15 15
E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 A 4 6 A 4 6 A 4 6 A 4 6 HM 2 2 HM 2 2
EQ OUT
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 8 8 8 8
0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 15 15 15 15
APPENDIX 17
active subwoofer 119SA
Connection example 2
FIG 2: triplet configuration (example A) One 119SA + two powered speaker enclosures 260A
Mixer "L/R" outputs ➟ 119SA "L" and "R" inputs
119SA "L" and "R" x-over outputs ➟ 260A inputs
2-way active speaker enclosure mod. 260A
Montarbo
2 - WAY
Power Amplifier MADE IN ITALY BY
Montarbo
2 - WAY
PROCESSOR CONTROLLED PROCESSOR CONTROLLED
POWERED SPEAKER SYSTEM POWERED SPEAKER SYSTEM
LEVEL LEVEL
MOD. 260 A 0 10
MOD. 260 A 0 10
2
3
3
1
1
CAUTION ! ALWAYS REPLACE FUSE CAUTION ! ALWAYS REPLACE FUSE
WITH SAME TYPE AND RATING L WITH SAME TYPE AND RATING L
A V I S ! REPLACER TOUJOURS I A V I S ! REPLACER TOUJOURS I
^
UN FUSIBLE DE MEME CARACTERISTIQUES N ^
UN FUSIBLE DE MEME CARACTERISTIQUES N
K K
1
1
3
3
2
2
BALANCED INPUT BALANCED INPUT
pin1 GND pin 2 pin 3 INPUT pin1 GND pin 2 pin 3 INPUT
POWER ( P.max 400W ) 230V 50/60Hz FUSE F 2A POWER ( P.max 400W ) 230V 50/60Hz FUSE F 2A
Active subwoofer mod. 119SA
Montarbo MOD.
POWER
119 SA
600W
POWERED PROCESSOR CONTROLLED
STEREO SUBWOOFER SYSTEM
100Hz 20KHz
GND
FLAT
LIFT
L L L
LINK INPUT X-OVER OUT
4 5 6
3 7
2 8
1 9
0 10
INPUT
R R / mono R LEVEL
FUSE F 5A 230V 50/60Hz
MADE IN ITALY
L - R MIXER OUTPUTS
230V
L L
(mono)
MIC MIC MIC MIC MIC MIC MIC
1 2 mute mute
A B L R
R R R R R R
0 I
48V D.C. 100Hz 20KHz
LINE LINE LINE LINE LINE LINE LINE MONO AUX OUTPUTS MASTER OUTPUTS CTRL ROOM
GND
POWER
L L L L
FLAT
INSERT INSERT INSERT
(mono) (mono) (mono) (mono)
1 EFF SEND 2 C AUX SEND D Montarbo
6 7 8 9 10 11 12 13 14 15 16 OUTPUTS LEVEL
GAIN GAIN GAIN GAIN GAIN GAIN GAIN C AUX SEND D
4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6
A B L R LIFT
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8
9 9 9 L L
10 10 10 10 10 10 10 0 10 0 10
6 6 6
HF 2 2 HF 2 2 HF 2 2
HF 2 2 HF 2 2 HF 2 2 HF 2 2
1 4
EXT. EFF. SEND
6 4 6
2 3 3 3
INPUT X-OVER OUT
8 8 8 8 8 8
8 8 8 8 8 8 8 8 2 8 2 8 dB 0 0 0 dB
15 15 15 15 15 15
1.3 1.3 1.3 15 15 15 15 15 15 15 15
4 5 6
0 10 0 10 3 3 3
.75 1.6 .75 1.6 .75 1.6
.3 2 .3 2 .3 2
STEREO DIGITAL 6 6 6
MF MF MF MF
.18 3 KHz .18 3 KHz .18 3 KHz
2 2 2 2 2 2 2 2
EFFECTS PROCESSORS 3 7
MF MF MF 8 8 8 8 8 8 8 8
9 9 9
2 2 2 2 2 2
15 15 15 15 15 15 15 15
E1 12 12 12
2 8
8 8 8 8 8 8
E2
15 15 15
15 15 dB 15 15 dB 15 15 dB LF 2 2 LF 2 2 LF 2 2 LF 2 2
LF 2 2 LF 2 2 LF 2 2 18 18 18
8 8 8 8 8 8 8 8
8 8 8 8 8 8 E1/E2 LOAD
15 15 15 15 15 15 15 15
15 15 15 15 15 15
A 4 6 A 4 6 A 4 6 A 4 6 A 4 6 A 4 6 A 4 6
12 12
2 8 2 8 2 8 2 8 2 8 2 8 2 8 PROGRAMS SELECTOR 9 9
6 6
0 10 0 10 0 10 0 10 0 10 0 10 0 10
3 3
B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 INPUT LEVEL INPUT LEVEL
dB 0 0 dB
3 3 3 3
2 8 2 8 2 8 2 8 2 8 2 8 2 8 6 6
dB 0 dB 0 9 9
0 10 0 10 0 10 0 10 0 10 0 10 0 10 12 12
3 3
C 4 6 C 4 6 C 4 6 C 4 6 C 4 6 C 4 6 C 4 6
10 10
2 8 2 8 2 8 2 8 2 8 2 8 2 8 20 20
0 10 0 10 0 10 0 10 0 10 0 10 0 10
Hz 31 63 125 250 500 1K 2K 4K 8K 16K
D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 4 6 4 6
GAIN 4 6 GAIN 4 6 HF 2 2 HF 2 2
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8
2 8 2 8 8 8 8 8
0 10 0 10 0 10 0 10 0 10 0 10 0 10 flat flat
pre pre pre pre pre pre pre
post post post post post post post on on 10 10 15 15 15 15
E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 A 4 6 A 4 6 A 4 6 A 4 6 HM 2 2 HM 2 2
EQ OUT
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 8 8 8 8
0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 15 15 15 15
APPENDIX 18
active subwoofer 119SA
Connection example 3
FIG 3: triplet configuration (example B) One 119SA + two powered speaker enclosures 260A
Mixer "AUX" output ➟ 119SA "R" input
Mixer "L" output ➟ 260A input
Mixer "R" output ➟ 260A input
Montarbo MOD.
POWER
119 SA
600W
POWERED PROCESSOR CONTROLLED
STEREO SUBWOOFER SYSTEM
Montarbo
2 - WAY
100Hz 20KHz
GND Power Amplifier MADE IN ITALY BY
Montarbo
2 - WAY
PROCESSOR CONTROLLED PROCESSOR CONTROLLED
POWERED SPEAKER SYSTEM FLAT POWERED SPEAKER SYSTEM
LEVEL
MOD. 260 A 0 10
MOD. 260 A 0 10 LEVEL
2
3
3
LIFT
1
1
CAUTION ! ALWAYS REPLACE FUSE CAUTION ! ALWAYS REPLACE FUSE
WITH SAME TYPE AND RATING L WITH SAME TYPE AND RATING L
A V I S ! REPLACER TOUJOURS
^
UN FUSIBLE DE MEME CARACTERISTIQUES
I
N L L L A V I S ! REPLACER TOUJOURS
^
UN FUSIBLE DE MEME CARACTERISTIQUES
I
N
K K
1
3
3
2
2
BALANCED INPUT BALANCED INPUT
pin1 GND pin 2 pin 3 INPUT pin1 GND pin 2 pin 3 INPUT
POWER ( P.max 400W ) 230V 50/60Hz FUSE F 2A
4 5 6 POWER ( P.max 400W ) 230V 50/60Hz FUSE F 2A
3 7
2 8
1 9
0 10
INPUT
R R / mono R LEVEL
FUSE F 5A 230V 50/60Hz
MADE IN ITALY
L - R OUTS
AUX OUT
230V
50 60Hz
FUSE T
STEREO EFF. RET. 1 EFF. FT/SW 2 0,5 A
L L
(mono)
MIC MIC MIC MIC MIC MIC MIC
1 2 mute mute
A B L R
R R R R R R
0 I
48V D.C.
LINE LINE LINE LINE LINE LINE LINE MONO AUX OUTPUTS MASTER OUTPUTS CTRL ROOM
POWER
L L L L
INSERT INSERT INSERT
(mono) (mono) (mono) (mono)
1 EFF SEND 2 C AUX SEND D Montarbo
6 7 8 9 10 11 12 13 14 15 16 OUTPUTS LEVEL
GAIN GAIN GAIN GAIN GAIN GAIN GAIN C AUX SEND D
4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6
A B L R
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8
9 9 9
10 10 10 10 10 10 10 0 10 0 10
6 6 6
HF 2 2 HF 2 2 HF 2 2
HF 2 2 HF 2 2 HF 2 2 HF 2 2
1 4
EXT. EFF. SEND
6 4 6
2 3 3 3
8 8 8 8 8 8
8 8 8 8 8 8 8 8 2 8 2 8 dB 0 0 0 dB
15 15 15 15 15 15
1.3 1.3 1.3 15 15 15 15 15 15 15 15 0 10 0 10 3 3 3
.75 1.6 .75 1.6 .75 1.6
.3 2 .3 2 .3 2
STEREO DIGITAL 6 6 6
MF 2 2 MF 2 2 MF 2 2 MF 2 2
EFFECTS PROCESSORS
.18 3 KHz .18 3 KHz .18 3 KHz 9 9 9
MF MF MF 8 8 8 8 8 8 8 8
2 2 2 2 2 2
E1 12 12 12
15 15 15 15 15 15 15 15
8 8 8 8 8 8
E2
15 15 15
15 15 dB 15 15 dB 15 15 dB LF 2 2 LF 2 2 LF 2 2 LF 2 2
LF 2 2 LF 2 2 LF 2 2 18 18 18
8 8 8 8 8 8 8 8
8 8 8 8 8 8 E1/E2 LOAD
15 15 15 15 15 15 15 15
15 15 15 15 15 15
A 4 6 A 4 6 A 4 6 A 4 6 A 4 6 A 4 6 A 4 6
12 12
2 8 2 8 2 8 2 8 2 8 2 8 2 8 PROGRAMS SELECTOR 9 9
6 6
0 10 0 10 0 10 0 10 0 10 0 10 0 10
3 3
B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 INPUT LEVEL INPUT LEVEL
dB 0 0 dB
3 3 3 3
2 8 2 8 2 8 2 8 2 8 2 8 2 8 6 6
dB 0 dB 0 9 9
0 10 0 10 0 10 0 10 0 10 0 10 0 10 12 12
3 3
C 4 6 C 4 6 C 4 6 C 4 6 C 4 6 C 4 6 C 4 6
10 10
2 8 2 8 2 8 2 8 2 8 2 8 2 8 20 20
0 10 0 10 0 10 0 10 0 10 0 10 0 10
Hz 31 63 125 250 500 1K 2K 4K 8K 16K
D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 4 6 4 6
GAIN 4 6 GAIN 4 6 HF 2 2 HF 2 2
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8
2 8 2 8 8 8 8 8
0 10 0 10 0 10 0 10 0 10 0 10 0 10 flat flat
pre pre pre pre pre pre pre
post post post post post post post on on 10 10 15 15 15 15
E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 A 4 6 A 4 6 A 4 6 A 4 6 HM 2 2 HM 2 2
EQ OUT
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 8 8 8 8
0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 15 15 15 15
APPENDIX 19
active subwoofer 119SA
Connection example 4
FIG 4: parallel connection Mixer outputs ➟ 'R'/mono inputs of two 119SA
'link' outputs of the two 119SA ➟ 'R'/mono inputs of
other two 119SA ➟ 'link' outputs of the two 119SA ➟ ...
SATELLITE SATELLITE
▲ ▲
Montarbo 119 SA
ACTIVE SUBWOOFER Montarbo MOD.
POWER
119 SA
600W
Montarbo 119 SA
ACTIVE SUBWOOFER Montarbo MOD.
POWER
119 SA
600W
POWERED PROCESSOR CONTROLLED POWERED PROCESSOR CONTROLLED
STEREO SUBWOOFER SYSTEM STEREO SUBWOOFER SYSTEM
FLAT FLAT
LIFT LIFT
L L L L L L
LINK INPUT X-OVER OUT
'R' OUT 4 5 6
LINK INPUT
'R' OUT
X-OVER OUT
4 5 6
3 7 3 7
▲ ▲
2 8 2 8
1 9 1 9
0 10 0 10
INPUT INPUT
R R / mono R LEVEL R R / mono R LEVEL
FUSE F 5A 230V 50/60Hz FUSE F 5A 230V 50/60Hz
'R' IN 'R' IN
➩
➩
SATELLITE SATELLITE
▲ ▲
LINK OUT LINK OUT
Montarbo 119 SA Montarbo 119 SA
➩
➩
FLAT FLAT
LIFT LIFT
L L L L L L
LINK INPUT X-OVER OUT
'R' OUT 4 5 6
LINK INPUT
'R' OUT
X-OVER OUT
4 5 6
3 7 3 7
R
▲
R / mono R
2
1
0 10
INPUT
LEVEL
9
8
R
▲
R / mono R
2
1
0 10
INPUT
LEVEL
8
9
'R' IN
MADE IN ITALY MADE IN ITALY
'R' IN
➩
➩
SATELLITE SATELLITE
▲ ▲
LINK OUT LINK OUT
Montarbo 119 SA Montarbo 119 SA
➩
➩
MOD. MOD.
Montarbo 119 SA Montarbo 119 SA
ACTIVE SUBWOOFER
FLAT FLAT
LIFT LIFT
L L L L L L
LINK INPUT
'R' OUT
X-OVER OUT
4 5 6
LINK INPUT
'R' OUT
X-OVER OUT
4 5 6
3 7 3 7
▲ ▲
2 8 2 8
1 9 1 9
0 10 0 10
INPUT INPUT
R R / mono R LEVEL R R / mono R LEVEL
FUSE F 5A 230V 50/60Hz FUSE F 5A 230V 50/60Hz
'R' IN
MADE IN ITALY MADE IN ITALY
'R' IN
➩
L-R
OUTPUTS
230V
50 60Hz
FUSE T
STEREO EFF. RET. 1 EFF. FT/SW 2 0,5 A
L L
(mono)
MIC MIC MIC MIC MIC MIC MIC
1 2 mute mute
A B L R
R R R R R R
0 I
48V D.C.
LINE LINE LINE LINE LINE LINE LINE MONO AUX OUTPUTS MASTER OUTPUTS CTRL ROOM
POWER
L L L L
INSERT INSERT INSERT
(mono) (mono) (mono) (mono)
1 EFF SEND 2 C AUX SEND D Montarbo
6 7 8 9 10 11 12 13 14 15 16 OUTPUTS LEVEL
GAIN GAIN GAIN GAIN GAIN GAIN GAIN C AUX SEND D
4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6
A B L R
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8
9 9 9
10 10 10 10 10 10 10 0 10 0 10
6 6 6
HF 2 2 HF 2 2 HF 2 2
HF 2 2 HF 2 2 HF 2 2 HF 2 2
1 4
EXT. EFF. SEND
6 4 6
2 3 3 3
8 8 8 8 8 8
8 8 8 8 8 8 8 8 2 8 2 8 dB 0 0 0 dB
15 15 15 15 15 15
1.3 1.3 1.3 15 15 15 15 15 15 15 15 0 10 0 10 3 3 3
.75 1.6 .75 1.6 .75 1.6
.3 2 .3 2 .3 2
STEREO DIGITAL 6 6 6
MF 2 2 MF 2 2 MF 2 2 MF 2 2
EFFECTS PROCESSORS
.18 3 KHz .18 3 KHz .18 3 KHz 9 9 9
MF MF MF 8 8 8 8 8 8 8 8
2 2 2 2 2 2
E1 12 12 12
15 15 15 15 15 15 15 15
8 8 8 8 8 8
E2
15 15 15
15 15 dB 15 15 dB 15 15 dB LF 2 2 LF 2 2 LF 2 2 LF 2 2
LF 2 2 LF 2 2 LF 2 2 18 18 18
8 8 8 8 8 8 8 8
8 8 8 8 8 8 E1/E2 LOAD
15 15 15 15 15 15 15 15
15 15 15 15 15 15
A 4 6 A 4 6 A 4 6 A 4 6 A 4 6 A 4 6 A 4 6
12 12
2 8 2 8 2 8 2 8 2 8 2 8 2 8 PROGRAMS SELECTOR 9 9
6 6
0 10 0 10 0 10 0 10 0 10 0 10 0 10
3 3
B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 B 4 6 INPUT LEVEL INPUT LEVEL
dB 0 0 dB
3 3 3 3
2 8 2 8 2 8 2 8 2 8 2 8 2 8 6 6
dB 0 dB 0 9 9
0 10 0 10 0 10 0 10 0 10 0 10 0 10 12 12
3 3
C 4 6 C 4 6 C 4 6 C 4 6 C 4 6 C 4 6 C 4 6
10 10
2 8 2 8 2 8 2 8 2 8 2 8 2 8 20 20
0 10 0 10 0 10 0 10 0 10 0 10 0 10
Hz 31 63 125 250 500 1K 2K 4K 8K 16K
D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 D 4 6 4 6 4 6
GAIN 4 6 GAIN 4 6 HF 2 2 HF 2 2
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8
2 8 2 8 8 8 8 8
0 10 0 10 0 10 0 10 0 10 0 10 0 10 flat flat
pre pre pre pre pre pre pre
post post post post post post post on on 10 10 15 15 15 15
E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 E1 4 6 A 4 6 A 4 6 A 4 6 A 4 6 HM 2 2 HM 2 2
EQ OUT
2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 2 8 8 8 8 8
0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 15 15 15 15
APPENDIX 20
active subwoofer 119SA
Block diagram
Spare parts
18" high efficency custom woofer A300157 A088676 B010020 A300157
Amplifier chassis: D521190 A088677
Power transformer B005010
Power amplifier D00119F
Power amplifier heat sink D52118T
Control and connection panel D521201
Metal grid D201192
Stand holder B010020
Transport handles A088676
A088677 D521201
D521190
B005010
D00119F
D52118T
D201192
APPENDIX 21
Le informazioni contenute in questo manuale Les indications contenues en ce manuel ont Las informaciónes contenidas en este manual
sono state attentamente redatte e controllate. été attentivement rédigées et contrôlées. han sidos atentamente redactas y verificadas.
Tuttavia non si assume alcuna responsabilità Toutefois nous n'assumons aucune responsa- De todos modos no asumimos alguna
per eventuali inesattezze. bilité pour des éventuelles inexactitudes. responsabilidad de eventuales inexactitudes.
Questo manuale non può contenere una Ce manuel ne peut contenir une réponse Este manual no puede contener una respuesta
risposta a tutti i singoli problemi che possono pour problèmes particuliers qui pourraient se a todos los problemas que pueden presentarse
presentarsi durante l'installazione e l'uso présenter lors de l’installation et de l’usage durante la instalación y el uso de estos
dell'apparecchio. Siamo a vostra disposizione de l’appareil. Nous sommes à votre disposi- aparatos. Estamos a vuestra disposición para
per fornirvi eventuali ulteriori informazioni e tion pour d’éventuels conseils et informations facilitar informes y consejos.
consigli. supplémentaires.
Elettronica Montarbo srl no puede ser conside-
La Elettronica Montarbo srl non può essere Elettronica Montarbo srl ne peut être rada responsable de daños que puedan ser
ritenuta responsabile per danni o incidenti a consideré responsable des dommages causés causados a personas o cosas derivados de la
cose o persone, causati o connessi all’utilizza- à des personnes ou à des objects lors de l'uti- utilizaciòn del aparato.
zione o malfunzionamento dell’apparecchio. lisation du produit.
elettronica Montarbo srl The information contained in this manual has Die in dieser Bedienungsanleitung enthaltenen
been carefully drawn up and checked. Hinweise wurden sorgfältig bearbeitet und
via G. di Vittorio 13 However no responsibility will be assumed for korrigiert. Es wird jedoch keine Gewähr für
any inexactitude. die Richtigkeit der Angaben übernommen.
40057 Cadriano di Granarolo This manual can not cover all the possible Diese Bedienungsanleitung kann nicht alle
Bologna, Italy contingencies which may arise during Richtlinien und Probleme berücksichtigen,
installation and use of the product. welche während der Aufstellung und
Should further information be desired, please Verwendung des Gerätes entstehen können.
Tel. +39. 051. 76 64 37 contact us or our local distributor. Sollten Sie Fragen haben, wenden Sie sich
bitte an uns oder an den für Ihr Land zuständi-
Fax. +39. 051. 76 52 26 Elettronica Montarbo srl can not be gen Importeur.
E-mail: mail@montarbo.com considered responsible for damages which
may be caused to people and things when Die Elettronica Montarbo srl haftet nicht,
Internet: www.montarbo.com using this product. für Personen- oder Sachschäden die durch die
Verwendung des Gerätes entstehen.
CARATTERISTICHE E DATI TECNICI POSSONO ESSERE MODIFICATI SENZA PREAVVISO. SPECIFICATIONS AND FEATURES ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
ÄNDERUNGEN VORBEHALTEN. LAS CARACTERISTICAS Y LOS DATOS TECNICOS PUEDEN SUFRIR MODIFICACIONES SIN PREVIO AVISO. SOUS RESERVE DE MODIFICATIONS.