Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
INSTRUCTION MANUAL
1M23N22201
TABLE OF CONTENTS
2 <Table of Contents>
FUNCTIONS OF MODEL MENU ................. 69 $33(1',;...................................................... 120
Ɣ&RPPRQ)XQFWLRQV ........................................ 69 7LPHU6767 ............................................. 120
6HUYR0RQLWRU/LQNDJH0HQX 6ZLWFK6HWWLQJ0HWKRG................................. 121
&RQGLWLRQ6HOHFW*OLG+HOLRQO\.................. 70
Dual Rate ........................................................ 72
3URJUDP0L[................................................... 74
)XHO0L[$LU+HOLRQO\ ................................ 76
Ɣ$LUSODQH*OLGHU)XQFWLRQV ............................. 78
Model Menu functions list............................. 78
7KURWWOH&XUYH$LURQO\ .............................. 80
7KURWWOH'HOD\$LURQO\ ............................... 81
$,/'LIIHUHQWLDO([FHSW$,/ ................... 82
)ODS6HWWLQJ)/3DQGXS.......................... 83
$,/WR&DPEHU)/3$,/)/3DQGXS84
$,/WR%UDNH)/3*OLGRQO\)/3 .......... 85
AIL to RUD..................................................... 86
RUD to AIL..................................................... 87
&DPEHU0L[([FHSW$,/ ......................... 88
(/(WR&DPEHU([FHSW$,/.................... 90
&DPEHU)/3WR(/($,/)/3DQGXS91
%XWWHUÀ\*OLGRQO\QRUPDOZLQJ$,/DQG
XSÀ\LQJZLQJ$,/)/3DQGXS ........ 92
7ULP0L[*OLGRQO\$,/DQGXS............. 94
$LUEUDNH$LURQO\$,/DQGXS ............... 96
*\UR$LURQO\IRU*<$W\SHJ\UR .............. 98
V-tail .............................................................. 100
$LOHYDWRU........................................................ 101
:LQJOHW)O\LQJZLQJRQO\ .......................... 102
0RWRU............................................................. 103
58'WR(/($LURQO\ ................................ 105
6QDS5ROO$LURQO\ ..................................... 106
Ɣ+HOLFRSWHU)XQFWLRQV .................................... 108
Model Menu functions list........................... 108
3,7&XUYH3LWWULP....................................... 109
7+5&XUYH7KURWWOHKRYHUWULP................. 112
7KURWWOH+ROG ................................................ 114
6ZDVK0L[..................................................... 115
7KURWWOH0L[.................................................. 116
3,7WR58'5HYROXWLRQPL[ ..................... 117
*\URIRU*<W\SHJ\UR .............................. 118
*RYHUQRU ....................................................... 119
<Table of Contents> 3
INTRODUCTION
Thank you for purchasing a Futaba® FASST-2.4GHz* 8FG series digital proportional R/C system. This system is
extremely versatile and may be used by beginners and pros alike. In order for you to make the best use of your
V\VWHPDQGWRÀ\VDIHO\SOHDVHUHDGWKLVPDQXDOFDUHIXOO\,I\RXKDYHDQ\GLI¿FXOWLHVZKLOHXVLQJ\RXUV\VWHP
SOHDVHFRQVXOWWKHPDQXDORXURQOLQH)UHTXHQWO\$VNHG4XHVWLRQVRQWKHZHESDJHVUHIHUHQFHGEHORZ\RXU
KREE\GHDOHURUWKH)XWDED6HUYLFH&HQWHU
*FASST: Futaba Advanced Spread Spectrum Technology
'XH WR XQIRUHVHHQ FKDQJHV LQ SURGXFWLRQ SURFHGXUHV WKH LQIRUPDWLRQ FRQWDLQHG LQ WKLV PDQXDO LV VXEMHFW WR
FKDQJHZLWKRXWQRWLFH
6XSSRUWDQG6HUYLFH,WLVUHFRPPHQGHGWRKDYH\RXU)XWDEDHTXLSPHQWVHUYLFHGDQQXDOO\GXULQJ\RXUKREE\¶V
“off season” to ensure safe operation.
IN NORTH AMERICA
3OHDVHIHHOIUHHWRFRQWDFWWKH)XWDED6HUYLFH&HQWHUIRUDVVLVWDQFHLQRSHUDWLRQXVHDQGSURJUDPPLQJ3OHDVH
EHVXUHWRUHJXODUO\YLVLWWKH)*)UHTXHQWO\$VNHG4XHVWLRQVZHEVLWHDWZZZIXWDEDUFFRPIDT7KLVSDJH
LQFOXGHV H[WHQVLYH SURJUDPPLQJ XVH VHW XS DQG VDIHW\ LQIRUPDWLRQ RQ WKH )* UDGLR V\VWHP DQG LV XSGDWHG
UHJXODUO\$Q\WHFKQLFDOXSGDWHVDQG86PDQXDOFRUUHFWLRQVZLOOEHDYDLODEOHRQWKLVZHESDJH,I\RXGRQRW
¿QGWKHDQVZHUVWR\RXUTXHVWLRQVWKHUHSOHDVHVHHWKHHQGRIRXU)$4DUHDIRULQIRUPDWLRQRQFRQWDFWLQJXV
via email for the most rapid and convenient response.
'RQ¶WKDYH,QWHUQHWDFFHVV",QWHUQHWDFFHVVLVDYDLODEOHDWQRFKDUJHDWPRVWSXEOLFOLEUDULHVVFKRROVDQGRWKHU
SXEOLFUHVRXUFHV:H¿QGLQWHUQHWVXSSRUWWREHDIDEXORXVUHIHUHQFHIRUPDQ\PRGHOHUVDVLWHPVFDQEHSULQWHG
DQGVDYHGIRUIXWXUHUHIHUHQFHDQGFDQEHDFFHVVHGDWDQ\KRXURIWKHGD\QLJKWZHHNHQGRUKROLGD\,I\RXGR
QRWZLVKWRDFFHVVWKHLQWHUQHWIRULQIRUPDWLRQKRZHYHUGRQ¶WZRUU\2XUVXSSRUWWHDPVDUHDYDLODEOH0RQGD\
through Friday 8-5 Central time to assist you.
3OHDVHFRQWDFW\RXU)XWDEDLPSRUWHULQ\RXUUHJLRQRIWKHZRUOGWRDVVLVW\RXZLWKDQ\TXHVWLRQVSUREOHPVRU
service needs.
3OHDVHUHFRJQL]HWKDWDOOLQIRUPDWLRQLQWKLVPDQXDODQGDOOVXSSRUWDYDLODELOLW\LVEDVHGXSRQWKHV\VWHPVVROG
LQ1RUWK$PHULFDRQO\3URGXFWVSXUFKDVHGHOVHZKHUHPD\YDU\$OZD\VFRQWDFW\RXUUHJLRQ¶VVXSSRUWFHQWHUIRU
assistance.
4 < ,QWURGXFWLRQ >
$SSOLFDWLRQ([SRUWDQG0RGL¿FDWLRQ
7KLV SURGXFW PD\ EH XVHG IRU PRGHO DLUSODQH RU VXUIDFH ERDW FDU URERW XVH ,W LV QRW LQWHQGHG IRU XVH LQ
DQ\DSSOLFDWLRQRWKHUWKDQWKHFRQWURORIPRGHOVIRUKREE\DQGUHFUHDWLRQDOSXUSRVHV7KHSURGXFWLVVXEMHFWWR
UHJXODWLRQVRIWKH0LQLVWU\RI5DGLR7HOHFRPPXQLFDWLRQVDQGLVUHVWULFWHGXQGHU-DSDQHVHODZWRVXFKSXUSRVHV
2. Exportation precautions:
D :KHQ WKLV SURGXFW LV H[SRUWHG IURP WKH FRXQWU\ RI PDQXIDFWXUH LWV XVH LV WR EH DSSURYHG E\ WKH ODZV
JRYHUQLQJWKHFRXQWU\RIGHVWLQDWLRQZKLFKJRYHUQGHYLFHVWKDWHPLWUDGLRIUHTXHQFLHV,IWKLVSURGXFWLVWKHQUH
H[SRUWHGWRRWKHUFRXQWULHVLWPD\EHVXEMHFWWRUHVWULFWLRQVRQVXFKH[SRUW3ULRUDSSURYDORIWKHDSSURSULDWH
JRYHUQPHQW DXWKRULWLHV PD\ EH UHTXLUHG ,I \RX KDYH SXUFKDVHG WKLV SURGXFW IURP DQ H[SRUWHU RXWVLGH \RXU
FRXQWU\ DQG QRW WKH DXWKRUL]HG )XWDED GLVWULEXWRU LQ \RXU FRXQWU\ SOHDVH FRQWDFW WKH VHOOHU LPPHGLDWHO\ WR
determine if such export regulations have been met.
E8VHRIWKLVSURGXFWZLWKRWKHUWKDQPRGHOVPD\EHUHVWULFWHGE\([SRUWDQG7UDGH&RQWURO5HJXODWLRQVDQG
DQDSSOLFDWLRQIRUH[SRUWDSSURYDOPXVWEHVXEPLWWHG7KLVHTXLSPHQWPXVWQRWEHXWLOL]HGWRRSHUDWHHTXLSPHQW
other than radio controlled models.
0RGL¿FDWLRQDGMXVWPHQWDQGUHSODFHPHQWRISDUWV)XWDEDLVQRWUHVSRQVLEOHIRUXQDXWKRUL]HGPRGL¿FDWLRQ
DGMXVWPHQWDQGUHSODFHPHQWRISDUWVRQWKLVSURGXFW$Q\VXFKFKDQJHVPD\YRLGWKHZDUUDQW\
&RPSOLDQFH,QIRUPDWLRQ6WDWHPHQWIRU86$
7KLVGHYLFHWUDGHQDPH)XWDED&RUSRUDWLRQRI$PHULFDPRGHOQXPEHU5+6FRPSOLHVZLWKSDUWRIWKH
)&&5XOHV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJWZRFRQGLWLRQV
7KLVGHYLFHPD\QRWFDXVHKDUPIXOLQWHUIHUHQFHDQG
7KLV GHYLFH PXVW DFFHSW DQ\ LQWHUIHUHQFH UHFHLYHG LQFOXGLQJ LQWHUIHUHQFH WKDW PD\ FDXVH XQGHVLUHG
operation.
The responsible party of this device compliance is:
Futaba Service Center
1$SROOR'ULYH6XLWH&KDPSDLJQ,/86$
7(/RU(PDLOVXSSRUW#IXWDEDUFFRP6XSSRUW
7(/RU(PDLOVHUYLFH#IXWDEDUFFRP6HUYLFH
7KH 5%5& 6($/ RQ WKH QLFNHOFDGPLXP EDWWHU\ FRQWDLQHG LQ )XWDED SURGXFWV LQGLFDWHV WKDW
)XWDED&RUSRUDWLRQRI$PHULFDLVYROXQWDULO\SDUWLFLSDWLQJLQDQLQGXVWU\ZLGHSURJUDPWRFROOHFW
DQGUHF\FOHWKHVHEDWWHULHVDWWKH HQG RI WKHLU XVHIXO OLYHV ZKHQ WDNHQ RXW RI VHUYLFH ZLWKLQ WKH
United States. The RBRC. program provides a convenient alternative to placing used nickel-
FDGPLXPEDWWHULHVLQWRWKHWUDVKRUPXQLFLSDOZDVWHV\VWHPZKLFKLVLOOHJDOLQVRPHDUHDV
IRU86$
<RX PD\ FRQWDFW \RXU ORFDO UHF\FOLQJ FHQWHU IRU LQIRUPDWLRQ RQ ZKHUH WR UHWXUQ WKH VSHQW EDWWHU\ 3OHDVH
FDOO %$77(5< IRU LQIRUPDWLRQ RQ 1L&G EDWWHU\ UHF\FOLQJ LQ \RXU DUHD )XWDED &RUSRUDWLRQ RI
America's involvement in this program is part of its commitment to protecting our environment and conserving
natural resources.
< ,QWURGXFWLRQ > 5
)HGHUDO&RPPXQLFDWLRQV&RPPLVVLRQ,QWHUIHUHQFH6WDWHPHQWIRU86$
7KLVHTXLSPHQWKDVEHHQWHVWHGDQGIRXQGWRFRPSO\ZLWKWKHOLPLWVIRUD&ODVV%GLJLWDOGHYLFHSXUVXDQWWR3DUW
RIWKH)&&5XOHV7KHVHOLPLWVDUHGHVLJQHGWRSURYLGHUHDVRQDEOHSURWHFWLRQDJDLQVWKDUPIXOLQWHUIHUHQFHLQ
a residential installation.
7KLV HTXLSPHQW JHQHUDWHV XVHV DQG FDQ UDGLDWH UDGLR IUHTXHQF\ HQHUJ\ DQG LI QRW LQVWDOOHG DQG XVHG LQ
DFFRUGDQFH ZLWK WKH LQVWUXFWLRQV PD\ FDXVH KDUPIXO LQWHUIHUHQFH WR UDGLR FRPPXQLFDWLRQV +RZHYHU WKHUH LV
QRJXDUDQWHHWKDWLQWHUIHUHQFHZLOOQRWRFFXULQDSDUWLFXODULQVWDOODWLRQ,IWKLVHTXLSPHQWGRHVFDXVHKDUPIXO
LQWHUIHUHQFHWRUDGLRRUWHOHYLVLRQUHFHSWLRQZKLFKFDQEHGHWHUPLQHGE\WXUQLQJWKHHTXLSPHQWRIIDQGRQWKH
XVHULVHQFRXUDJHGWRWU\WRFRUUHFWWKHLQWHUIHUHQFHE\RQHRUPRUHRIWKHIROORZLQJPHDVXUHV
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user's
DXWKRULW\WRRSHUDWHWKHHTXLSPHQW
([SRVXUHWR5DGLR)UHTXHQF\5DGLDWLRQ
7R FRPSO\ ZLWK )&& 5) H[SRVXUH FRPSOLDQFH UHTXLUHPHQWV D VHSDUDWLRQ GLVWDQFH RI DW OHDVW FP PXVW EH
PDLQWDLQHGEHWZHHQWKHDQWHQQDRIWKLVGHYLFHDQGDOOSHUVRQV
7KLVGHYLFHPXVWQRWEHFRORFDWHGRURSHUDWLQJLQFRQMXQFWLRQZLWKDQ\RWKHUDQWHQQDRUWUDQVPLWWHU
0HDQLQJRI6SHFLDO0DUNLQJV
3D\VSHFLDODWWHQWLRQWRVDIHW\ZKHUHLQGLFDWHGE\WKHIROORZLQJPDUNV
n DANGER 3URFHGXUHV ZKLFK PD\ OHDG WR GDQJHURXV FRQGLWLRQV DQG FDXVH GHDWKVHULRXV LQMXU\ LI QRW
carried out properly.
n WARNING 3URFHGXUHV ZKLFK PD\ OHDG WR D GDQJHURXV FRQGLWLRQ RU FDXVH GHDWK RU VHULRXV LQMXU\ WR
WKHXVHULIQRWFDUULHGRXWSURSHUO\RUSURFHGXUHVZKHUHWKHSUREDELOLW\RIVXSHU¿FLDOLQMXU\RUSK\VLFDO
damage is high.
n CAUTION3URFHGXUHVZKHUHWKHSRVVLELOLW\RIVHULRXVLQMXU\WRWKHXVHULVVPDOOEXWWKHUHLVDGDQJHURI
LQMXU\RUSK\VLFDOGDPDJHLIQRWFDUULHGRXWSURSHUO\
l = Prohibited j 0DQGDWRU\
:DUQLQJ$OZD\VNHHSHOHFWULFDOFRPSRQHQWVDZD\IURPVPDOOFKLOGUHQ
FLYING SAFETY
n WARNING
7RHQVXUHWKHVDIHW\RI\RXUVHOIDQGRWKHUVSOHDVHREVHUYHWKHIROORZLQJSUHFDXWLRQV
j +DYH UHJXODU PDLQWHQDQFH SHUIRUPHG$OWKRXJK \RXU )* SURWHFWV WKH PRGHO PHPRULHV ZLWK QRQ
YRODWLOH((3520PHPRU\ZKLFKGRHVQRWUHTXLUHSHULRGLFUHSODFHPHQWDQGQRWDEDWWHU\WKHWUDQVPLWWHU
VWLOOVKRXOGKDYHUHJXODUFKHFNXSVIRUZHDUDQGWHDU:HUHFRPPHQGVHQGLQJ\RXUV\VWHPWRWKH)XWDED
6HUYLFH&HQWHUDQQXDOO\GXULQJ\RXUQRQÀ\LQJVHDVRQIRUDFRPSOHWHFKHFNXSDQGVHUYLFH
6 < ,QWURGXFWLRQ >
1L0+1L&G%DWWHU\
j &KDUJHWKHEDWWHULHV6HH&KDUJLQJWKH1L&GEDWWHULHVIRUGHWDLOV$OZD\VUHFKDUJHWKHWUDQVPLWWHUDQG
UHFHLYHUEDWWHULHVEHIRUHHDFKÀ\LQJVHVVLRQ$ORZEDWWHU\ZLOOVRRQGLHSRWHQWLDOO\FDXVLQJORVVRIFRQWURO
DQGDFUDVK:KHQ\RXEHJLQ\RXUÀ\LQJVHVVLRQUHVHW\RXU)*¶VEXLOWLQWLPHUDQGGXULQJWKHVHVVLRQ
pay attention to the duration of usage.
j 6WRSÀ\LQJORQJEHIRUH\RXUEDWWHULHVEHFRPHORZRQFKDUJH'RQRWUHO\RQ\RXUUDGLR¶VORZEDWWHU\
ZDUQLQJ V\VWHPV LQWHQGHG RQO\ DV D SUHFDXWLRQ WR WHOO \RX ZKHQ WR UHFKDUJH$OZD\V FKHFN \RXU
WUDQVPLWWHUDQGUHFHLYHUEDWWHULHVSULRUWRHDFKÀLJKW
:KHUHWR)O\
:HUHFRPPHQGWKDW\RXÀ\DWDUHFRJQL]HGPRGHODLUSODQHÀ\LQJ¿HOG<RXFDQ¿QGPRGHOFOXEVDQG¿HOGV
E\DVNLQJ\RXUQHDUHVWKREE\GHDOHURULQWKH86E\FRQWDFWLQJWKH$FDGHP\RI0RGHO$HURQDXWLFV
<RX FDQ DOVR FRQWDFW WKH QDWLRQDO$FDGHP\ RI 0RGHO$HURQDXWLFV $0$ ZKLFK KDV PRUH WKDQ
FKDUWHUHG FOXEV DFURVV WKH FRXQWU\ 7KURXJK DQ\ RQH RI WKHP LQVWUXFWRU WUDLQLQJ SURJUDPV DQG LQVXUHG
QHZFRPHUWUDLQLQJDUHDYDLODEOH&RQWDFWWKH$0$DWWKHDGGUHVVRUWROOIUHHSKRQHQXPEHUEHORZ
$FDGHP\RI0RGHO$HURQDXWLFV
(DVW0HPRULDO'ULYH
0XQFLH,1
7HOH
)D[
RUYLDWKH,QWHUQHWDWKWWS??ZZZPRGHODLUFUDIWRUJ
j $OZD\V SD\ SDUWLFXODU DWWHQWLRQ WR WKH IO\LQJ ILHOG¶V UXOHV DV ZHOO DV WKH SUHVHQFH DQG ORFDWLRQ RI
VSHFWDWRUVWKHZLQGGLUHFWLRQDQGDQ\REVWDFOHVRQWKH¿HOG%HYHU\FDUHIXOÀ\LQJLQDUHDVQHDUSRZHU
OLQHVWDOOEXLOGLQJVRUFRPPXQLFDWLRQIDFLOLWLHVDVWKHUHPD\EHUDGLRLQWHUIHUHQFHLQWKHLUYLFLQLW\
< ,QWURGXFWLRQ > 7
1L0+1L&G%DWWHU\6DIHW\DQG+DQGOLQJLQVWUXFWLRQV
,03257$17
Use only the )XWDED VSHFLDO FKDUJHU LQFOXGHG ZLWK WKLV VHW RU RWKHU FKDUJHUV DSSURYHG E\ )XWDED WR
FKDUJHWKH1L0+EDWWHULHVLQWKH)*WUDQVPLWWHUDQG1L&GEDWWHULHVLQFOXGHGZLWKWKLVVHW
,W LV LPSRUWDQW WR XQGHUVWDQG WKH RSHUDWLQJ FKDUDFWHULVWLFV RI 1L0+1L&G EDWWHULHV$OZD\V UHDG WKH
VSHFL¿FDWLRQVSULQWHGRQWKHODEHORI\RXU1L0+1L&GEDWWHU\DQGFKDUJHUSULRUWRXVH)DLOXUHWRIROORZWKH
SURFHHGLQJSUHFDXWLRQVFDQTXLFNO\UHVXOWLQVHYHUHSHUPDQHQWGDPDJHWRWKHEDWWHULHVDQGLWVVXUURXQGLQJVDQG
possibly result in a ),5(
,03257$1735(&$87,216
l 'RQRWDWWHPSWWRGLVDVVHPEOH1L0+1L&GSDFNVRUFHOOV
l 'RQRWDOORZ1L0+1L&GFHOOVWRFRPHLQFRQWDFWZLWKPRLVWXUHRUZDWHUDWDQ\WLPH
j $OZD\V SURYLGH DGHTXDWH YHQWLODWLRQ DURXQG 1L0+1L&G EDWWHULHV GXULQJ FKDUJH GLVFKDUJH ZKLOH LQ
XVHDQGGXULQJVWRUDJH
l 'RQRWOHDYHD1L0+1L&GEDWWHU\XQDWWHQGHGDWDQ\WLPHZKLOHEHLQJFKDUJHGRUGLVFKDUJHG
l 'RQRWDWWHPSWWRFKDUJH1L0+1L&GEDWWHULHVZLWKDFKDUJHUWKDWLV127GHVLJQHGIRU1L0+1L&G
EDWWHULHVDVSHUPDQHQWGDPDJHWRWKHEDWWHU\DQGFKDUJHUFRXOGUHVXOW
j $OZD\VFKDUJH1L0+1L&GEDWWHULHVLQD¿UHSURRIORFDWLRQ'RQRWFKDUJHRUGLVFKDUJH1L0+1L&G
EDWWHULHV RQ FDUSHW D FOXWWHUHG ZRUNEHQFK QHDU SDSHU SODVWLF YLQ\O OHDWKHU RU ZRRG RU LQVLGH DQ 5&
PRGHORUIXOOVL]HGDXWRPRELOH0RQLWRUWKHFKDUJHDUHDZLWKDVPRNHRU¿UHDODUP
l 'RQRWFKDUJH1L0+1L&GEDWWHULHVDWFXUUHQWVJUHDWHUWKDQWKH³&´UDWLQJRIWKHEDWWHU\³&´HTXDOV
WKHUDWHGFDSDFLW\RIWKHEDWWHU\
l 'R QRW DOORZ 1L0+1L&G FHOOV WR RYHUKHDW DW DQ\ WLPH &HOOV ZKLFK UHDFK JUHDWHU WKDQ GHJUHHV
)DKUHQKHLW&VKRXOGEHSODFHGLQD¿UHSURRIORFDWLRQ
j 1L0+1L&GFHOOVZLOOQRWFKDUJHIXOO\ZKHQWRRFROGRUVKRZIXOOFKDUJH
j ,W LV QRUPDO IRU WKH EDWWHULHV WR EHFRPH ZDUP GXULQJ FKDUJLQJ EXW LI WKH FKDUJHU RU EDWWHU\ EHFRPHV
H[FHVVLYHO\KRWGLVFRQQHFWWKHEDWWHU\IURPWKHFKDUJHULPPHGLDWHO\$OZD\VLQVSHFWDEDWWHU\ZKLFKKDV
SUHYLRXVO\RYHUKHDWHGIRUSRWHQWLDOGDPDJHDQGGRQRWUHXVHLI\RXVXVSHFWLWKDVEHHQGDPDJHGLQDQ\
ZD\
l 'R QRW XVH D 1L0+1L&G EDWWHU\ LI \RX VXVSHFW SK\VLFDO GDPDJH KDV RFFXUUHG WR WKH SDFN &DUHIXOO\
LQVSHFW WKH EDWWHU\ IRU HYHQ WKH VPDOOHVW RI GHQWV FUDFNV VSOLWV SXQFWXUHV RU GDPDJH WR WKH ZLULQJ DQG
FRQQHFWRUV '2 127 DOORZ WKH EDWWHU\¶V LQWHUQDO HOHFWURO\WH WR JHW LQWR H\HV RU RQ VNLQ²ZDVK DIIHFWHG
DUHDVLPPHGLDWHO\LIWKH\FRPHLQFRQWDFWZLWKWKHHOHFWURO\WH,ILQGRXEWSODFHWKHEDWWHU\LQD¿UHSURRI
location for at least 30 minutes.
l 'RQRWVWRUHEDWWHULHVQHDUDQRSHQÀDPHRUKHDWHU
l 'R QRW GLVFKDUJH 1L0+1L&G EDWWHULHV DW FXUUHQWV ZKLFK H[FHHG WKH GLVFKDUJH FXUUHQW UDWLQJ RI WKH
battery.
j $OZD\VVWRUH1L0+1L&GFHOOVSDFNVLQDVHFXUHORFDWLRQDZD\IURPFKLOGUHQ
6HFXUH'LJLWDO6'0HPRU\&DUG+DQGOLQJ,QVWUXFWLRQV
6'FDUGLVQRWLQFOXGHGZLWKWKLVVHW
l 1HYHUUHPRYHWKH6'FDUGRUWXUQRIISRZHUZKLOH l 'RQRWH[SRVHWKH6'FDUGWRGLUWPRLVWXUHZDWHU
entering data. RUÀXLGVRIDQ\NLQG
l 1HYHUVWRUHWKH6'FDUGZKHUHLWPD\EHVXEMHFW j $OZD\V KROG WKH 6' FDUG E\ WKH HGJHV GXULQJ
WRVWURQJVWDWLFHOHFWULFLW\RUPDJQHWLF¿HOGV installation and removal.
l 'R QRW H[SRVH WKH 6' FDUG WR GLUHFW VXQOLJKW j Be certain to insert the SD card in the correct
excessive humidity or corrosive environments. direction.
8 < ,QWURGXFWLRQ >
$WWKHÀ\LQJ¿HOG
7RSUHYHQWSRVVLEOHGDPDJHWR\RXUUDGLRJHDUWXUQWKHSRZHUVZLWFKHVRQDQGRIILQWKHSURSHUVHTXHQFH
3XOOWKURWWOHVWLFNWRLGOHSRVLWLRQRURWKHUZLVHGLVDUP\RXUPRWRUHQJLQH
7XUQRQWKHWUDQVPLWWHUSRZHUDQGDOORZ\RXUWUDQVPLWWHUWRUHDFKLWVKRPHVFUHHQ
&RQ¿UPWKHSURSHUPRGHOPHPRU\KDVEHHQVHOHFWHG
7XUQRQ\RXUUHFHLYHUSRZHU
7HVWDOOFRQWUROV,IDVHUYRRSHUDWHVDEQRUPDOO\GRQ¶WDWWHPSWWRÀ\XQWLO\RXGHWHUPLQHWKHFDXVHRIWKH
problem.
7HVW WR HQVXUH WKDW WKH )DLO6DIH VHWWLQJV DUH FRUUHFW DIWHU DGMXVWLQJ WKHP 7XUQ WKH WUDQVPLWWHU RII DQG
FRQ¿UPWKHSURSHUVXUIDFHWKURWWOHPRYHPHQWV7XUQWKHWUDQVPLWWHUEDFNRQ
6WDUW\RXUHQJLQH
&RPSOHWHDIXOOUDQJHFKHFN
$IWHUÀ\LQJEULQJ\RXUWKURWWOHVWLFNWRLGOHSRVLWLRQHQJDJHDQ\NLOOVZLWFKHVRURWKHUZLVHGLVDUP\RXU
motor/engine.
7XUQRIIUHFHLYHUSRZHU
7XUQRIIWUDQVPLWWHUSRZHU
,I\RXGRQRWWXUQRQ\RXUV\VWHPLQWKLVRUGHU\RXPD\GDPDJH\RXUVHUYRVRUFRQWUROVXUIDFHVÀRRG\RXU
HQJLQHRULQWKHFDVHRIHOHFWULFSRZHUHGRUJDVROLQHSRZHUHGPRGHOVWKHHQJLQHPD\XQH[SHFWHGO\WXUQRQ
DQGFDXVHDVHYHUHLQMXU\
j :KLOH\RXDUHJHWWLQJUHDG\WRÀ\LI\RXSODFH\RXUWUDQVPLWWHURQWKHJURXQGEHVXUHWKDWWKHZLQG
ZRQ
WWLSLWRYHU,ILWLVNQRFNHGRYHUWKHWKURWWOHVWLFNPD\EHDFFLGHQWDOO\PRYHGFDXVLQJWKHHQJLQHWR
VSHHGXS$OVRGDPDJHWR\RXUWUDQVPLWWHUPD\RFFXU
j In order to maintain complete control of your aircraft it is important that LWUHPDLQVYLVLEOHDWDOOWLPHV.
)O\LQJEHKLQGODUJHREMHFWVVXFKDVEXLOGLQJVJUDLQELQVHWFLVQRWVXJJHVWHG'RLQJVRPD\UHVXOWLQWKH
UHGXFWLRQRIWKHTXDOLW\RIWKHUDGLRIUHTXHQF\OLQNWRWKHPRGHO
l 'R QRW JUDVS WKH WUDQVPLWWHU
V DQWHQQD GXULQJ ÀLJKW 'RLQJ VR PD\ GHJUDGH WKH TXDOLW\ RI WKH UDGLR
IUHTXHQF\WUDQVPLVVLRQ
j $VZLWKDOOUDGLRIUHTXHQF\WUDQVPLVVLRQVWKHVWURQJHVWDUHDRIVLJQDOWUDQVPLVVLRQLVIURPWKHVLGHVRIWKH
WUDQVPLWWHU
VDQWHQQD$VVXFKWKHDQWHQQDVKRXOGQRWEHSRLQWHGGLUHFWO\DWWKHPRGHO,I\RXUÀ\LQJVW\OH
FUHDWHVWKLVVLWXDWLRQHDVLO\PRYHWKHDQWHQQDWRFRUUHFWWKLVVLWXDWLRQ
l 'RQ¶WÀ\LQWKHUDLQ Water or moisture may enter the transmitter through the antenna or stick openings
DQGFDXVHHUUDWLFRSHUDWLRQRUORVVRIFRQWURO,I\RXPXVWÀ\LQZHWZHDWKHUGXULQJDFRQWHVWEHVXUHWR
FRYHU\RXUWUDQVPLWWHUZLWKDSODVWLFEDJRUZDWHUSURRIEDUULHU1HYHUÀ\LIOLJKWQLQJLVH[SHFWHG
< ,QWURGXFWLRQ > 9
BEFORE USE
)HDWXUHV
)$667*+]V\VWHP
7KH7)*WUDQVPLWWHULVFDSDEOHRIWUDQVPLWWLQJLQERWK)$667*FKDQG0XOWLFKPRGHV6HOHFW
WKHGHVLUHGPRGXODWLRQPRGHLQWKH)UHTXHQF\0HQX)RUFRPSOHWHGHWDLOVRQKRZWRGRVRSOHDVHUHIHU
WRWKH)UHTXHQF\6HOHFWLRQVHFWLRQORFDWHGHOVHZKHUHLQWKLVPDQXDO7KHFRPSDWLELOLW\LVGHSHQGHQWXSRQ
WKHUHFHLYHUVHOHFWHG7KH5+6UHFHLYHULVFDSDEOHRIFRQWUROOLQJPRGHOVXSWRHLJKWFKDQQHOV
5+6KDVWZRRSHUDWLRQPRGHDVVKRZQEHORZ
5HFHLYHU1RUPDOPRGH+LJK6SHHGPRGH
7KH1RUPDOPRGHDFFHSWVDQ\W\SHRIVHUYRVRUWKHSHULSKHUDOVDVWKHIUDPHUDWHRIWKHRXWSXWLVPV
7KH+LJK6SHHGPRGHRQO\DFFHSWVWKHGLJLWDOVHUYRVIRURXWSXWVIURPFKWRFK7KLVLQFOXGHVWKH%/6
VHULHVDQGPRVWSHULSKHUDOHTXLSPHQWVXFKDVJ\URVDQGEUXVKOHVV(6&V7KHIUDPHUDWHRIWKHRXWSXWVLV
PV7KHRXWSXWVIRURWKHUFKDQQHOVLQGLFDWHGDOORZWKHXVHRIDQ\W\SHRIVHUYRVDVWKHIUDPHUDWHRIWKHVH
RXWSXWVDUHVWLOOPVRQWKH+LJK6SHHGPRGH
)$667*+]V\VWHPIHDWXUHV
• 2.4GHz Spread Spectrum radio communication system.
• Exclusive ID code to avoid interference from other FASST systems.
)DLO6DIH)6IXQFWLRQIRUWKURWWOHFKDQQHODWFKPRGH)6%DWWHU\)6
'XDODQWHQQDGLYHUVLW\5+6
1RUPDOPRGHRU+LJK6SHHGPRGHLVVHOHFWDEOH5+6
7)**+]V\VWHPDQGUHFHLYHUFRPSDWLELOLW\
Receiver
0RGHOW\SHV
)RXUW\SHVRIPDLQZLQJVDQGWKUHHW\SHVRIWDLOZLQJVDUHDYDLODEOHIRUDLUSODQHV6L[VZDVKW\SHVDUH
DYDLODEOHIRUKHOLFRSWHUV6L[W\SHVRIPDLQZLQJVDQGWKUHHW\SHVRIWDLOZLQJVDUHDYDLODEOHIRUJOLGHUV
Functions and mixing functions necessary for each model type are set in advance at the factory.
'DWDLQSXW
/DUJHJUDSKLF/&'DQGQHZW\SH7RXFK6HQVRUVXEVWDQWLDOO\LPSURYHHDVHRIVHWXS
Stick
1HZVWLFNGHVLJQZLWKLPSURYHGIHHODGMXVWDEOHOHQJWKDQGWHQVLRQ
1L0+EDWWHU\
7)*LVRSHUDWHGE\D9P$K1LFNHO0HWDO+\GULGHEDWWHU\
10 %HIRUH8VH!
&RQWHQWVDQG7HFKQLFDO6SHFL¿FDWLRQV
6SHFL¿FDWLRQVDQGUDWLQJVDUHVXEMHFWWRFKDQJHZLWKRXWQRWLFH
<RXU)*$)*+)*LQFOXGHVWKHIROORZLQJFRPSRQHQWV
7)*$7)*+RU7)*7UDQVPLWWHU 6XJJHVWHG6HUYRIRUXVHZLWK\RXU)*V\VWHP
5+65HFHLYHU
6HUYR6'LJLWDOVHUYR
+7)%1L0+EDWWHU\ &KDUJHU
&RQWUROV\VWHP3XOVHZLGWKFRQWUROPVQHXWUDO
6ZLWFKKDUQHVV
3RZHUUHTXLUHPHQW9IURPUHFHLYHU
• Neck strap
2XWSXWWRUTXHR]LQNJFPDW9
*The set contents depend on the type of set.
2SHUDWLQJVSHHGVHFDW9
6L]H[[LQ[[PP
7UDQVPLWWHU7)*$7)*+7)* :HLJKWR]J
VWLFNFKDQQHO)$667*V\VWHP
7UDQVPLWWLQJIUHTXHQF\*+]EDQG
6HUYR6'LJLWDOVHUYR
0RGXODWLRQ*FKRU*0XOWLFKVZLWFKDEOH
&RQWUROV\VWHP3XOVHZLGWKFRQWUROPVQHXWUDO
3RZHUVXSSO\9+7)%1L0+EDWWHU\
3RZHUUHTXLUHPHQW9IURPUHFHLYHU
2XWSXWWRUTXHR]LQNJFPDW9
5HFHLYHU5+6 2SHUDWLQJVSHHGVHFDW9
)$667*V\VWHPGXDODQWHQQDGLYHUVLW\ 6L]H[[LQ[[PP
3RZHU UHTXLUHPHQW 9 RU 9 EDWWHU\ RU UHJXODWHG :HLJKWR]J
RXWSXWIURP(6&HWF
6L]H[[LQ[[PP
6HUYR66WDQGDUG'LJLWDOVHUYR
:HLJKWR]J
:KHQ XVLQJ (6&
V PDNH VXUH WKDW WKH UHJXODWHG &RQWUROV\VWHP3XOVHZLGWKFRQWUROPVQHXWUDO
output capacity meets your usage application. 3RZHUUHTXLUHPHQW9IURPUHFHLYHU
2XWSXWWRUTXHR]LQNJFPDW9
2SHUDWLQJVSHHGVHFDW9
8VDJHFRQGLWLRQRQ+LJK6SHHGPRGH 6L]H[[LQ[[PP
5+6 :HLJKWR]J
n CAUTION
6HUYR66WDQGDUGEDOOEHDULQJ
j :KHQXVLQJWKH5+6LQWKHKLJKVSHHG &RQWUROV\VWHP3XOVHZLGWKFRQWUROPVQHXWUDO
+6PRGHGLJLWDOVHUYRVDUHUHTXLUHGIRU 3RZHUUHTXLUHPHQW9IURPUHFHLYHU
WKH¿UVWVL[FKDQQHOV 2XWSXWWRUTXHR]LQNJFP
If an analog servo is connected to one of the first 2SHUDWLQJVSHHGVHF
VL[ FKDQQHOV ZKHQ LQ WKH KLJK VSHHG PRGH WKH
6L]H[[LQ[[PP
VHUYR ZLOO QRW IXQFWLRQ SURSHUO\$GGLWLRQDOO\
ZKLOHPDQ\SHULSKHUDOGHYLFHVZLOORSHUDWHLQHLWKHU :HLJKWR]J
WKHKLJKVSHHGRUQRUPDOPRGHVRPHZLOOQRW,I
WKHUH DUH DQ\ GLIILFXOWLHV QRWHG SOHDVH UHWXUQ WKH
reciever's operational mode to the "Normal" mode
WRGHWHUPLQHLIWKLVUHVROYHVWKHGLI¿FXOW\
,I XVLQJ WKH 5+6 LQ WKH KLJK VSHHG PRGH
analog servos may be used for channels seven and
eight.
)RU2SHUDWLRQ0RGH6HOHFWLRQVHHS
%HIRUH8VH! 11
7KHIROORZLQJDGGLWLRQDODFFHVVRULHVDUHDYDLODEOHIURP\RXUGHDOHU5HIHUWRD)XWDEDFDWDORJIRU
PRUHLQIRUPDWLRQ
+7)%7UDQVPLWWHUEDWWHU\SDFNWKHP$KWUDQVPLWWHU1L0+EDWWHU\SDFNPD\EHHDVLO\
H[FKDQJHGZLWKDIUHVKRQHWRSURYLGHHQRXJKFDSDFLW\IRUH[WHQGHGÀ\LQJVHVVLRQV
• Trainer cord - the optional training cord may be used to help a beginning pilot learn to fly easily by
placing the instructor on a separate transmitter. Note that the T8FG transmitter may be connected to
DQRWKHU7)*V\VWHPDVZHOODVWRDQ\RWKHUPRGHOVRI)XWDEDWUDQVPLWWHUV7KH7)*WUDQVPLWWHUXVHV
RQHRIWKHWKUHHFRUGSOXJW\SHVDFFRUGLQJWRWKHWUDQVPLWWHUFRQQHFWHG5HIHUWRWKHGHVFULSWLRQDWWKH
75$,1(5IXQFWLRQLQVWUXFWLRQV7KHSDUWQXPEHURIWKLVFRUGLV)870
• Neckstrap - a neckstrap may be connected to your T8FG system to make it easier to handle and improve
\RXUÀ\LQJSUHFLVLRQVLQFH\RXUKDQGVZRQ¶WQHHGWRVXSSRUWWKHWUDQVPLWWHU¶VZHLJKW
<KDUQHVVHVVHUYRH[WHQVLRQVHWF*HQXLQH)XWDEDH[WHQVLRQVDQG<KDUQHVVHVLQFOXGLQJDKHDY\GXW\
YHUVLRQZLWKKHDYLHUZLUHDUHDYDLODEOHWRDLGLQ\RXUODUJHUPRGHODQGRWKHULQVWDOODWLRQV
• Gyros - a variety of genuine Futaba gyros is available for your aircraft or helicopter needs.
5HFHLYHUVYDULRXVPRGHOVRI)XWDEDUHFHLYHUVPD\EHSXUFKDVHGIRUXVHLQRWKHUPRGHOV5HFHLYHUVIRU
)$667*+]0XOWLFKPRGHDQGFKPRGHW\SHVDUHDYDLODEOH
2SWLRQDO&KDUJHU)XWDED&51L0+1L&G7UDQVPLWWHU5HFHLYHU%DWWHU\&KDUJHU
12 %HIRUH8VH!
7UDQVPLWWHUFRQWUROV
Ɣ$QWHQQD
Ɣ0RQLWRU/('
Ɣ&DUULQJ+DQGOH
Ɣ9ROXPH/'5'
Ɣ6OLGH/HYHU/6 Ɣ6OLGH/HYHU56
Ɣ6WLFN Ɣ6WLFN
(J3) (J2)
(J4) (J1)
Ɣ/&''LVSOD\
Ɣ3RZHU6ZLWFK
Ɣ1HFN6WUDS$WWDFKPHQW
%HIRUH8VH! 13
7UDQVPLWWHU
V$QWHQQD 0RQLWRU/('GLVSOD\
$V ZLWK DOO UDGLR IUHTXHQF\ WUDQVPLVVLRQV WKH 7KHVWDWXVRIWKHWUDQVPLWWHULVGLVSOD\HGE\/('
strongest area of signal transmission is from the at the bottom left and right sides of the "T8FG"
VLGHV RI WKH WUDQVPLWWHU
V DQWHQQD$V VXFK WKH logo.
antenna should not be pointed directly at the model. /('/HIW
,I \RXU IO\LQJ VW\OH FUHDWHV WKLV VLWXDWLRQ HDVLO\
move the antenna to correct this situation. 'LVSOD\VWKHQRQGHIDXOWFRQGLWLRQZDUQLQJ
• Blinking
Power switch is turned on when any
condition switch is activated (in the ON
state).
/('5LJKW
' L V S O D \ V W K H V W D W H R I U D G L R I U H T X H Q F \
transmission.
• Off
Radio waves are in the OFF state.
n CAUTION • On
Radio waves are being transmitted.
j 3OHDVH GR QRW JUDVS WKH WUDQVPLWWHU
V
DQWHQQDGXULQJÀLJKW
6ZLWFK6$6+
'RLQJ VR PD\ GHJUDGH WKH TXDOLW\ RI WKH 5)
transmission to the model. (Switch Type)
• SA : 3 positions; Alternate; Short lever
• SB : 3 positions; Alternate; Long lever
• SC : 3 positions; Alternate; Long lever
• SD : 3 positions; Alternate; Short lever
• SE : 3 positions; Alternate; Short lever
• SF : 2 positions; Alternate; Long lever
• SG : 3 positions; Alternate; Short lever
• SH : 2 positions; Momentary; Long lever
<RXFDQFKRRVHVZLWFKDQGVHWWKH212))GLUHFWLRQLQWKH
setting screen of the mixing functions.
14 %HIRUH8VH!
Volume 'LJLWDO7ULP
T3 T2
LD RD T4 T1
'LJLWDO7ULP777DQG7
Volume LD and RD:
7KLVWUDQVPLWWHULVHTXLSSHGZLWKIRXUGLJLWDO
7KH YROXPH /' DQG 5' NQREV DOORZ DQDORJ WULPV(DFKWLPH\RXSUHVVDWULPEXWWRQWKHWULP
input. SRVLWLRQPRYHVRQHVWHS,I\RXFRQWLQXHSUHVVLQJLW
7KH7)*WUDQVPLWWHUEHHSVZKHQWKHYROXPHNQREUHDFKHV WKHWULPSRVLWLRQVWDUWVWRPRYHIDVWHU,QDGGLWLRQ
the center position. ZKHQ WKH WULP SRVLWLRQ UHWXUQV WR WKH FHQWHU WKH
*You can use each setting screen of the mixing functions to WRQH ZLOO FKDQJH<RX FDQ DOZD\V PRQLWRU WULP
VHOHFWYROXPHVDQGGH¿QHWKHGLUHFWLRQRIDPRYHPHQW SRVLWLRQVE\UHIHUHQFLQJWKH/&'VFUHHQ
*You can select the trim step amount and the display unit
6OLGH/HYHU RQWKHKRPHVFUHHQRQWKH77VHWWLQJVFUHHQZLWKLQWKH
linkage menu.
1RWH7KHWULPSRVLWLRQV\RXKDYHVHWZLOOEHVWRUHGLQWKH
QRQYRODWLOHPHPRU\DQGZLOOUHPDLQWKHUH
LS RS
%HIRUH8VH! 15
7RXFKVHQVRURSHUDWLRQ
Data input operation is performed using the touch sensor.
SensorTouch™ operation Condition Working
• Short 'tap' If the screen has more than one page. (Ex. P-MIX screen) The cursor moves to the top of next page.
S1 If the screen have only one (1) page. The cursor moves to the top of page.
If the input data mode with blinking the setting data. The input data is canceled.
RTN At the input data mode. Change to the moving cursor mode.
At the input data mode with blinking the setting data. The data is entered.
• Two short 'taps' Home screen, System menu, Linkage Menu, Model
menu, Selecting ON/OFF Switch, USER NAME,
MODEL NAME, DISPLAY, INFO, MODEL SELECT,
Jump to System Menu screen directly.
SYS MODEL TYPE, FREQUECY, DATA RESET, TIMER,
Selecting Control, Selecting Function, SERVO
MONITOR
At all screens except those noted above. Jump to Servo Monitor screen directly.
• Scrolling
Lightly circling the outside edge of the RTN button. The cursor moves accordingly.
Outline
of
“RTN”
During the data input mode. Increases or decreases values accordingly.
0RYHPHQWRIFXUVRUYDOXHLQSXWRUPRGHVHOHFWLRQ: S1 button:
0RYHPHQWRIWKHFXUVRURQWKHPHQXVFUHHQDQG When there is a next page on a menu screen or
movement of the cursor among items on a setup VHWXSVFUHHQ\RXFDQJRWRWKDWSDJHE\WRXFKLQJ
screen can be controlled by scrolling your finger WKH6EXWWRQ,QWKLVFDVHWKHFXUVRUPRYHVWRWKH
WRWKHOHIWDQGULJKWLQWKHGLUHFWLRQRIWKHDUURZLQ screen title item of the page.
the scrolling diagram above. You can also go to the
([LWLQJVHWXSVFUHHQ
QH[WSDJHLIWKHUHLVDQH[WSDJH
To end the operation on a setup screen and return
7KLV VFUROOLQJ WHFKQLTXH LV DOVR XVHG IRU GDWD
WRWKHPHQXVFUHHQPRYHWKHFXUVRUWRWKHVFUHHQ
LQSXW YDOXH LQSXW PRGH VHOHFWLRQ DQG VLPLODU
title item and touch the RTN button.
RSHUDWLRQV ([DPSOHV LQFOXGH9DOXH 21 2))
,1+$&7HWF 7RUHWXUQWRKRPHVFUHHQGLUHFWO\WRXFKWKH6
EXWWRQIRUVHFRQG
RTN button:
$OWHUQDWLYHO\PRYHWKHFXUVRUWRWKHVFUHHQWLWOH
7RXFKWKH571EXWWRQZKHQ\RXZDQWWRRSHQ item and touch the RTN button to return to the
DVHWXSVFUHHQRUWRVZLWFKEHWZHHQFXUVRUPRYH home screen from a menu screen.
PRGHUHYHUVHGLVSOD\DQGGDWDLQSXWPRGHER[
GLVSOD\
This button can also be used as the enter button
ZKHQDFRQILUPDWLRQPHVVDJHLVGLVSOD\HGRQWKH
VFUHHQHWF
16 %HIRUH8VH!
Note: Stick Adjustment
6FUROORSHUDWLRQ&LUFOH\RXU¿QJHURQWKHRXWVLGHHGJHRI
$GMXVWPHQWRIWKHVWLFNOHYHUOHQJWK
the RTN button. The sensors may mis-read your touch as a
UHYHUVHURWDWLRQLIWKHFLUFOHLVVPDOOHURUSHUIRUPHGRQWKH <RXFDQDGMXVWWKHOHQJWKRIVWLFNOHYHUVDV\RX
inside edge of the RTN button. OLNH,WLVUHFRPPHQGHGWRDGMXVWWKHOHQJWKRIWKH
VWLFNVLQOLQHZLWK\RXUKDQGVL]H
Lever Head Lever Head
A B
$GMXVWPHQWRIVWLFNOHYHUWHQVLRQ
The tension of the self-return type stick lever can
EHDGMXVWHG
1. First, Remove the battery cover on the
bottom of the transmitter. Next, unplug the
battery wire and remove the battery from
the transmitter.
2. Next, using a screwdriver, remove the five
screws that hold the transmitter's rear case
in position, and put them in a safe place.
Gently ease off the transmitter's rear case.
Now you'll see the view shown in the figure
,IWKH6HQVRU7RXFKGRHVQRWUHJLVWHU\RXULQSXWSOHDVH below.
WU\DJDLQDIWHUOLJKWO\WDSSLQJ\RXU¿QJHURQWKHVHQVRURQFH
again.
'RQRWRSHUDWHWKH6HQVRU7RXFKZLWKJORYHVZRUQ7KH •Stick Tension (J2)
SensorTouch™ might not react. ((Mode 2)) •Stick Tension (J4)
((Mode 1/2))
n CAUTION
•Stick Tension (J1)
j 7KH WRXFK VHQVRU PLJKW QRW RSHUDWH E\ ((Mode 1/2))
UHFHLYLQJ WKH VSDUN QRLVH JHQHUDWHG IURP •Stick Tension (J3)
WKHJDVROLQHHQJLQHHWF,QWKLVFDVHSOHDVH ((Mode 1))
RSHUDWH \RXU WUDQVPLWWHU IURP WKH QRLVH
VRXUFHDSDUW 2. Use a small Phillips screwdriver to adjust the
spring strength as you prefer by turning the
adjusting screw of the stick you want to
adjust.
7XUQLQJWKHVFUHZFORFNZLVHLQFUHDVHVWKHWHQVLRQ
CAUTION: If you loosen the screw too much,
the stick may not operate because it is
caught internally.
3) At the end of adjustment, re-install the rear
case.
%HIRUH8VH! 17
6'&DUG6HFXUH'LJLWDOPHPRU\FDUG1RW ,QVHUWLQJUHPRYLQJWKH6'FDUG
LQFOXGHG 1. Turn off the transmitter power and then
The T8FG transmitter model data can be stored open the battery cover at the bottom of the
transmitter.
by using any commonly found SD card. When
7)*WUDQVPLWWHUXSGDWHVRIWZDUHLVUHOHDVHGWKH 2.
VRIWZDUHLVXSGDWHGXVLQJDQ6'FDUG7KH7)*
LVFDSDEOHRIXVLQJ6'FDUGVZLWKDPHPRU\VL]H
SD Card Slot
EHWZHHQ0%DQG*%
l $VWKH6'FDUGLVDSUHFLVLRQGHYLFHGRQRW
XVHH[FHVVLYHIRUFHZKHQLQVHUWLQJ 6'FDUGLQLWLDOL]DWLRQ
7RXVHDQ6'FDUGZLWKWKH7)*WKHFDUGPXVW
ILUVWEHIRUPDWWHG2QFHIRUPDWWHGWKHFDUGGRHV
5HVWULFWLRQVZKHQXVLQJDQ6'FDUG not have to be reformatted. Formatting is performed
7KHIROORZLQJUHVWULFWLRQVDSSO\ZKHQXVLQJDQ by the T8FG.
SD card: [IMPORTANT] When an SD card is formatted
for the T8FG, all pre-existing data is
*The SD card must first be initialized using the T8FG
destroyed. Do not format a card containing
GHGLFDWHGIRUPDW7KH6'FDUGFDQQRWEHXVHGDVLVZLWKRXW
important data.
formatting for the T8FG.
*Initializing destroys all the data previously saved on the
card. [Formatting procedure]
$Q6'FDUGIRUPDWWHGWRWKH7)*FDQQRWEHZULWWHQGLUHFWO\ 1. Insert the SD card into the SD card slot of the
IURP D 3& E\:LQGRZV ([SORUHU HWF7KH ILOHV PXVW EH T8FG.
FRQYHUWHGDQGZULWWHQE\WKH)XWDED)LOH6\VWHPVRIWZDUH 2. T u r n o n t h e T 8 F G p o w e r . W h e n a n
)LOHVDUHLGHQWL¿HGE\QXPEHULQVWHDGRIQDPH7KLVVSHFLDO unformatted card is inserted into the T8FG,
FRQYHUVLRQVRIWZDUHFDQEHGRZQORDGHGIURP)XWDED
VZHE the screen shown below appears.
site at:
KWWSZZZIXWDEDUFFRPVHOOVKHHWVGRZQORDGVKWPO
18 %HIRUH8VH!
&RQQHFWRU3OXJ
•Trainer •Battery
charge
6WRUHGGDWD
If you have a problem saving or reading data
DIWHUDORQJSHULRGRIXVHZHVXJJHVWREWDLQLQJD
QHZ6'FDUGWRDYRLGIXUWKHUGLI¿FXOWLHV
*Futaba is not responsible for compensating any failure or
GDPDJHWRWKHGDWDVWRUHGLQWKHPHPRU\FDUG$VVXFKZH
suggest that you maintain a backup of your important data
contained on your SD card.
%HIRUH8VH! 19
,QVWDOODWLRQDQG5HPRYDORIWKH+7)%
7UDQVPLWWHU%DWWHU\
$WWDFKPHQWRIWKHEDWWHU\
1. Slide the battery cover on the bottom of the
transmitter toward the right side and open it.
2. Install the battery in the holder.
3. Connect the battery connector.
•Battery
•Battery Connector
%DWWHU\5HPRYDO
1RWH ,I \RX UHPRYH WKH EDWWHU\ ZKLOH WKH
SRZHU LV RQ WKH GDWD \RX KDYH VHW ZLOO QRW
EHVDYHG
1. Open the battery cover.
2. Disconnect the battery connector.
3. Pull up the right side of the battery and
remove the battery.
4. Close the battery cover completely.
n :DUQLQJ
j %HFDUHIXOQRWWRGURSWKHEDWWHU\
20 %HIRUH8VH!
5HFHLYHUQRPHQFODWXUH
%HIRUHXVLQJWKHUHFHLYHUEHVXUHWRUHDGWKHSUHFDXWLRQVOLVWHGLQWKHIROORZLQJSDJHV
8VDJHFRQGLWLRQRQ+LJK6SHHGPRGH
Link/Mode Switch
n CAUTION
j :KHQXVLQJWKH5+6LQWKHKLJKVSHHG
+6PRGHGLJLWDOVHUYRVDUHUHTXLUHGIRU
WKH¿UVWVL[FKDQQHOV
If an analog servo is connected to one of the first
VL[ FKDQQHOV ZKHQ LQ WKH KLJK VSHHG PRGH WKH
VHUYR ZLOO QRW IXQFWLRQ SURSHUO\$GGLWLRQDOO\
LED
ZKLOHPDQ\SHULSKHUDOGHYLFHVZLOORSHUDWHLQHLWKHU
WKHKLJKVSHHGRUQRUPDOPRGHVRPHZLOOQRW,I
&RQQHFWRU WKHUHDUH DQ\ GLIILFXOWLHVQRWHG SOHDVHUHWXUQ WKH
reciever's operational mode to the "Normal" mode
WKURXJKRXWSXWVIRUWKHFKDQQHOVWKURXJK WRGHWHUPLQHLIWKLVUHVROYHVWKHGLI¿FXOW\
'LJLWDOVHUYRRQO\LQWKH+LJK6SHHGPRGH ,I XVLQJ WKH 5+6 LQ WKH KLJK VSHHG PRGH
RXWSXWVIRUWKHFKDQQHOVDQG analog servos may be used for channels seven and
eight.
$QDORJRUGLJLWDOVHUYRVUHJDUGOHVVRIPRGH
)RU2SHUDWLRQ0RGH6HOHFWLRQVHHS
%FRQQHFWRUIRUWKHSRZHU
%HIRUH8VH! 21
%$6,&23(5$7,21
%DWWHU\&KDUJLQJ
%HIRUHFKDUJLQJEDWWHULHVUHDGWKH&DXWLRQVIRUKDQGOLQJEDWWHU\DQGEDWWHU\FKDUJHULQWKHVHFWLRQ1L
0+1L&G%DWWHU\6DIHW\DQG+DQGOLQJ,QVWUXFWLRQV
+RZWRFKDUJHWKH1L0+EDWWHU\+7)%
%DWWHU\FKDUJLQJZLOOQRWDXWRPDWLFDOO\VWRS5HPRYHWKH
battery and transmitter from the charger and remove the
IRUWKHWUDQVPLWWHUDQGWKH1L&GEDWWHU\
FKDUJHUIURPWKHZDOOVRFNHW
15)VROGVHSDUDWHO\IRUWKHUHFHLYHU
*It is recommended to reactivate the battery by cycling
several times if the battery has not been used for a long
n 'DQJHU period.
,QWKHFDVHRI1L0+1L&GEDWWHULHV\RXPD\ILQGSRRU
l 7KH 1L0+ EDWWHU\ +7)% LV RQO\ IRU performance of the battery if you have used the battery
\RXU7)*DQG7)*'RQRWXVHWKLVEDWWHU\ RQO\IRUDVKRUWSHULRGRULI\RXUHSHDWFKDUJLQJZKLOHWKH
battery is not fully discharged. It is suggested to discharge
IRURWKHUHTXLSPHQW
the battery to the recommended level after use. It is also
UHFRPPHQGHGWRFKDUJHWKHEDWWHU\MXVWEHIRUHXVH
j Be sure to use the attached special charger to
charge the battery.
,I \RX WDNH RXW WKH 1L0+ EDWWHU\ +7)% IURP WKH
WUDQVPLWWHU\RXFDQXVHWKHRSWLRQDOTXLFNFKDUJHU&5
FRUUHVSRQGLQJWR1L0+EDWWHU\
>0HWKRGRIFKDUJLQJEDWWHU\@
ƔSpecial charger
*Connect to AC outlet
specified.
To T8FG charge
connector
To receiver battery
22 %DVLF2SHUDWLRQ!
+RZWRWXUQWUDQVPLWWHUSRZHU212)) 5HJLVWUDWLRQRIWKHXVHU
VQDPH
: K H Q W X U Q L Q J R Q W K H S R Z H U W K H 7 ) * ,IVRGHVLUHGWKH7)*WUDQVPLWWHUFDQLQGLFDWH
WUDQVPLWWHUZLOOEHJLQHPPLWLQJ5)DXWRPDWLFDOO\ WKHRZQHU
VQDPH
DIWHULWFRQ¿UPVWKHVXUURXQGLQJ5)FRQGLWLRQV
8VHU
VQDPHVHWXSVFUHHQ
The T8FG transmitter also offers the ability to
1. Turn on the power of the transmitter.
DXWRVKXWGRZQ
*The home screen appears.
:KHQWXUQLQJRQWKHSRZHURIWKHWUDQVPLWWHU 2. Lightly touch the SYS button twice rapidly
1. Turn on the power switch of the transmitter. and the System menu appears.
7KHPHVVDJH&+(&.5)&21',7,21LVGLVSOD\HGIRUD 2. Select [USER NAME] in the System menu and
PRPHQW$WWKHVDPHWLPHWKHOHIW/('PRQLWRUEOLQNV touch the RTN button.
*The user name set up screen appears.
2. Then, you will see the home screen and the Input Box
transmitter begins to emit radio waves.
*Current user name is displayed.
7KHOHIWDQGULJKW/('PRQLWRUVZLOOFKDQJHWRVROLGUHG
&KDQJLQJWKHXVHUQDPH
+RZWRVWRSWKHWUDQVPLWWHU
1. Change the user name as described below:
1. Turn off the power switch of the transmitter.
[Moving cursor in input box]
7KHWUDQVPLWWHUVKXWVGRZQDWRQFH
6HOHFW >ł@ RU >ń@ DQG WRXFK WKH 571 EXWWRQ
[Deleting a character]
/RZEDWWHU\DODUPDQGDXWRVKXWGRZQ When [DELETE] is selected and the RTN button
is touched, the character immediately after
:KHQ WKH EDWWHU\ YROWDJH UHDFKHV 9 DQ the cursor is deleted.
DXGLEOH DODUP ZLOO VRXQG /DQG \RXU DLUFUDIW
[Adding a character]
immediately.
When a character is selected from the
:KHQ WKH EDWWHU\ YROWDJH UHDFKHV 9 WKH character list and the RTN button is touched,
WUDQVPLWWHUZLOOEHWXUQHGRIIDXWRPDWLFDOO\ that character is added at the position
,I \RX GR QRW RSHUDWH WKH WUDQVPLWWHU RU PRYH D VWLFN immediately after the cursor.
NQREVZLWFKRUGLJLWDOWULPIRUPLQXWHVWKHPHVVDJH
$QDPHRIXSWRFKDUDFWHUVORQJFDQEHHQWHUHGDVWKH
3/($6(78512))32:(56:,7&+LVGLVSOD\HGDQG XVHUQDPH$VSDFHLVDOVRFRXQWHGDVRQHFKDUDFWHU
DQDXGLEOHDODUPZLOOVRXQG 2. At the end of input, select [ENTER] and tuoch
the RTN button. (To terminate input and
return to the original state, select [CANCEL]
and touch the RTN button.)
%DVLF2SHUDWLRQ! 23
+RPHVFUHHQ
8VHWKHWRXFKVHQVRUWRVHOHFWWKHIROORZLQJGLVSOD\DUHDWRFDOOHDFKVHWWLQJVFUHHQDQGWRXFKWKH571
button. The setting screen appears.
6\VWHPWLPHU
.H\ORFN
• This shows the accumulated time since
the latest reset. (Hour):(Minute) • Touch the S1 button for one second
• Use the cursor to highlight this, then to lock/unlock the key operation.
touch the RTN button for one second In the key lock mode the key icon is
to reset the system timer. displayed here.
24 %DVLF2SHUDWLRQ!
2SHUDWLRQ0RGH6HOHFW5+6
7KHUHFHLYHURSHUDWLRQPRGHLVRQ1RUPDOPRGHIURPIDFWRU\VKLSSLQJ7RFKDQJHWKHPRGHSOHDVH
DGKHUHWRWKHIROORZLQJVWHSV
&KDQJLQJWKHRSHUDWLRQPRGH &RQ¿UPLQJWKHRSHUDWLRQPRGH
Link/Mode Button Please check the operation mode by observing
WKH/('ZKHQWXUQLQJRQWKHUHFHLYHU
If possible ensure that there's no FASST
transmitter in operation near the receiver.
2SHUDWLRQ0RGH6HOHFW
Turn on the receiver.
0 sec. 1 sec.
%DVLF2SHUDWLRQ! 25
(DV\/LQN7)*5+6
(DFKWUDQVPLWWHUKDVDQLQGLYLGXDOO\DVVLJQHGXQLTXH,'FRGH,QRUGHUWRVWDUWRSHUDWLRQWKHUHFHLYHU
PXVWEHOLQNHGZLWKWKH,'FRGHRIWKHWUDQVPLWWHUZLWKZKLFKLWLVEHLQJSDLUHG2QFHWKHOLQNLVPDGH
the ID code is stored in the receiver and no further linking is necessary unless the receiver is to be used
ZLWKDQRWKHUWUDQVPLWWHU:KHQ\RXSXUFKDVHDGGLWLRQDO5+6UHFHLYHUVWKLVSURFHGXUHLVQHFHVVDU\
RWKHUZLVHWKHUHFHLYHUZLOOQRWZRUN
/LQNSURFHGXUH
1. Place the transmitter and the receiver close R6008HS Easy LinkTM Operation
to each other within one (1) meter. 0 sec. 2 sec.
/(',QGLFDWLRQ5+6
Green Red Status
Off Solid No signal reception
Solid Off Receiving signals
Receiving signals but ID is
Blink Off
unmatched
26 %DVLF2SHUDWLRQ!
5DQJH7HVWLQJ<RXU5&6\VWHP
,WLVH[WUHPHO\LPSRUWDQWWRUDQJHFKHFN\RXUPRGHOVSULRUWRHDFKÀ\LQJVHVVLRQ7KLVHQDEOHV\RXWR
HQVXUHWKDWHYHU\WKLQJLVIXQFWLRQLQJDVLWVKRXOGDQGWRREWDLQPD[LPXPHQMR\PHQWIURP\RXUWLPHÀ\LQJ
7KH7)*WUDQVPLWWHULQFRUSRUDWHVDV\VWHPWKDWUHGXFHVLWVSRZHURXWSXWDQGDOORZV\RXWRSHUIRUPVXFK
a range check.
5DQJHFKHFNPRGH 5DQJHFKHFNSURFHGXUH
We have installed a special "Range check 1. With the "Range check mode" on, walk
mode" for doing a ground range check. To access away from the model while simultaneously
operating the controls. Have an assistant
the "Range check mode" touch and hold the RTN
stand by the model to confirm that all
EXWWRQZKLOHWXUQLQJRQWKHWUDQVPLWWHU'RLQJVR controls are completely and correctly
ZLOOEULQJXS32:(502'(PHQX operational. You should be able to walk
approximately 30-50 paces from the model
without losing control.
2. If everything operates correctly, return to
the model. Set the transmitter in a safe, yet
accessible, location so it will be within reach
after starting the engine or motor. Be certain
To activate the "Range check mode" touch the the throttle stick is in the low throttle position,
571EXWWRQDQGWKHUDQJHFKHFNPRGHVFUHHQZLOO then start the engine or motor. Perform
appear. another range check with your assistant
holding the aircraft with the engine running
at various speeds. If the servos jitter or move
inadvertently, there may be a problem. We
ZRXOG VWURQJO\ VXJJHVW \RX GR QRW Á\ XQWLO WKH
VRXUFH RI WKH GLIÀFXOW\ KDV EHHQ GHWHUPLQHG
Look for loose servo connections or binding
pushrods. Also, be certain that the battery
'XULQJ WKLV PRGH WKH 5) SRZHU RXWSXW LV has been fully charged.
reduced so the range test can be performed. In
DGGLWLRQ ZKHQ WKLV PRGH LV DFWLYDWHG WKH ULJKW
/('RQWKHIURQWRIWKHWUDQVPLWWHUVWDUWVEOLQNLQJ
DQG WKH WUDQVPLWWHU JLYHV XVHUV D ZDUQLQJ ZLWK D
beeping sound every 3 seconds.
7KH 5DQJH FKHFN PRGH FRQWLQXHV IRU
VHFRQGV DQG DIWHU WKDW WKH SRZHU ZLOO UHWXUQ
to the normal level. To exit the "Range check
PRGHEHIRUHWKHVHFRQGVVHOHFWWKH5$1*(
CHECK" at the top of the screen and touch the
RTN button again. This mode is available one
time only so if you need to re-use this function the
WUDQVPLWWHU SRZHU PXVW EH F\FOHG 1(9(5 VWDUW
À\LQJZKHQWKH5DQJHFKHFNPRGHLVDFWLYH
6KRXOG\RXUHTXLUHDGGLWLRQDOWLPHWRSHUIRUP
DUDQJHFKHFNKLJKOLJKW5HVWDUWEHIRUH\RXUWLPH
expires and press the RTN button one time.
%DVLF2SHUDWLRQ! 27
RECEIVER AND SERVO INSTALLATION
5HFHLYHUDQGVHUYRVFRQQHFWLRQ
&RQQHFWWKHUHFHLYHUDQGVHUYRVLQDFFRUGDQFHZLWKWKHFRQQHFWLRQGLDJUDPVKRZQEHORZ$OZD\VUHDG
>3UHFDXWLRQVZKHQPRXQWLQJWKHUHFHLYHUDQGVHUYRV@RU>%HIRUHXVLQJ@:KHQPRXQWLQJWKHUHFHLYHUDQG
VHUYRVWRWKHIXVHODJHFRQQHFWWKHQHFHVVDU\SRLQWVLQDFFRUGDQFHZLWKWKHPRGHO
VLQVWUXFWLRQPDQXDO
5HFHLYHUDQGVHUYRVFRQQHFWLRQGLDJUDP
Ɣ$OZD\VFRQQHFWWKHQHFHVVDU\QXPEHURIVHUYRV
Ɣ7KHUHFHLYHUFKDQQHODVVLJQPHQWGHSHQGVRQWKH
PRGHOW\SH6HHWKH6HUYRFRQQHFWLRQE\PRGHO
W\SHWDEOHV
R6008HSRXWSXWFRQQHFWRUVHFWLRQ
5HFHLYHUFRQQHFWRUV
Ɣ%3RZHUVXSSO\
Ɣ&+a2XWSXWFRQQHFWRUVa
Ɣ'$7$SRUWIDFWRU\XVHRQO\ (CH1~8)
CH1~8,B
(B)
Ni-Cd battery
28 5HFHLYHUDQG6HUYR,QVWDOODWLRQ!
6HUYRFRQQHFWLRQE\PRGHOW\SH
The T8FG transmitter channels are automatically assigned for optimal combination according to the type
VHOHFWHGZLWKWKH0RGHO7\SHIXQFWLRQRIWKH/LQNDJH0HQX7KHFKDQQHODVVLJQPHQWLQLWLDOVHWWLQJIRU
HDFKPRGHOW\SHLVVKRZQEHORZ&RQQHFWWKHUHFHLYHUDQGVHUYRVWRPDWFKWKHW\SHXVHG
7KHVHWFKDQQHOVFDQEHFKHFNHGDWWKH)XQFWLRQVFUHHQRIWKH/LQNDJH0HQX7KHFKDQQHODVVLJQPHQWVFDQDOVREHFKDQJHG)RU
PRUHLQIRUPDWLRQUHDGWKHGHVFULSWLRQRIWKH)XQFWLRQPHQX
$LUSODQHJOLGHU
1RUPDOZLQJDQG9WDLO
1 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron ---- Aileron ---- Aileron
2 Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator ---- Elevator ---- Elevator
3 Throttle Motor Throttle Motor Throttle Motor Throttle Motor ---- Rudder ---- Rudder
4 Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder ---- Aileron2 ---- Aileron2
5 Gear AUX7 Gear AUX7 Gear AUX6 Gear AUX5 ---- Flap ---- Aileron3
6 AUX6 AUX6 Aileron2 Aileron2 Flap Flap Aileron2 Aileron2 ---- Flap2 ---- Aileron4
7 AUX5 AUX5 AUX6 AUX6 Aileron2 Aileron2 Flap Flap ---- Flap3 ---- Flap
8 AUX4 AUX4 AUX5 AUX5 AUX5 AUX5 Flap2 Flap2 ---- Flap4 ---- Flap2
VC1 AUX1 AUX1 Camber Camber Camber Camber Camber Camber ---- Camber ---- Camber
VC2 AUX1 AUX1 AUX1 %XWWHUÁ\ AUX1 %XWWHUÁ\ AUX1 %XWWHUÁ\ ---- %XWWHUÁ\ ---- %XWWHUÁ\
VC3 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 ---- AUX1 ---- AUX1
VC4 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 ---- AUX1 ---- AUX1
Ɣ9&aDUHYLUWXDOFKDQQHOVZLWKRXWUHFHLYHURXWSXW)RUPRUHLQIRUPDWLRQVHHWKHGHVFULSWLRQRIWKH
)XQFWLRQPHQXRIWKH/LQNDJH0HQX
Ɣ7KHZLQJW\SHVZKLFKFDQEHVHOHFWHGGHSHQGRQWKH)$667PRGH0XOWLFKRUFKVHOHFWHG
7KHVHZLQJW\SHVDUHDYDLODEOHRQERWKWKH0XOWLFKDQGFKPRGH+RZHYHUWKHFKGRHVQ
WZRUNRQWKHFKPRGH
7KLVZLQJW\SHLVDYDLODEOHRQERWKWKH0XOWLFKDQGFKPRGH+RZHYHUVLQFHWKHFKGRHVQ
WZRUNRQWKHFKPRGHSOHDVH
DVVLJQWKHÀDSWRDQRWKHUFKDQQQHOZKLFKLVQ
WXVHG
7KHVHZLQJW\SHVDUHDYDLODEOHRQWKH0XOWLFKPRGHRQO\
5HFHLYHUDQG6HUYR,QVWDOODWLRQ! 29
$LOYDWRU'XDO(OHYDWRU
RX 1AIL(*1) 2AIL(*1) 2AIL+1FLAP(*2) 2AIL+2FLAP(*3)
CH Airplane Glider Airplane Glider Airplane Glider Airplane Glider
Ɣ9&aDUHYLUWXDOFKDQQHOVZLWKRXWUHFHLYHURXWSXW)RUPRUHLQIRUPDWLRQVHHWKHGHVFULSWLRQRIWKH
)XQFWLRQPHQXRIWKH/LQNDJH0HQX
Ɣ7KHZLQJW\SHVZKLFKFDQEHVHOHFWHGGHSHQGRQWKH)$667PRGH0XOWLFKRUFKVHOHFWHG
7KHVHZLQJW\SHVDUHDYDLODEOHRQERWKWKH0XOWLFKDQGFKPRGH+RZHYHUWKHFKGRHVQ
WZRUNRQWKHFKPRGH
7KLVZLQJW\SHLVDYDLODEOHRQERWKWKH0XOWLFKDQGFKPRGH+RZHYHUVLQFHWKHFKGRHVQ
WZRUNRQWKHFKPRGHSOHDVH
DVVLJQWKHHOHYDWRUWRDQRWKHUFKDQQQHOZKLFKLVQ
WXVHG
7KLVZLQJW\SHDLUSODQHW\SHLVDYDLODEOHRQWKH0XOWLFKPRGHRQO\7KLVZLQJW\SHJOLGHUW\SHLVDYDLODEOHRQERWKWKH0XOWL
FKDQGFKPRGH+RZHYHUVLQFHWKHFKGRHVQ
WZRUNRQWKHFKPRGHSOHDVHDVVLJQWKHÀDSWRDQRWKHUFKDQQQHOZKLFKLVQ
W
used.
30 5HFHLYHUDQG6HUYR,QVWDOODWLRQ!
)O\LQJZLQJ'HOWDZLQJ:LQJOHW
RX 2AIL(*1) 2AIL+1FLAP(*1) 2AIL+2FLAP(*2) 2AIL+4FLAP(*3) 4AIL+2FLAP(*3)
CH Airplane Glider Airplane Glider Airplane Glider Airplane Glider Airplane Glider
1 Aileron Aileron Aileron Aileron Aileron Aileron ---- Aileron ---- Aileron
2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 Rudder2 ---- Aileron2 ---- Aileron2
3 Throttle Motor Throttle Motor Throttle Motor ---- Rudder ---- Aileron3
4 Rudder Rudder Rudder Rudder Rudder Rudder ---- Rudder2 ---- Aileron4
5 Gear AUX7 Gear AUX6 Gear AUX6 ---- Flap ---- Rudder
6 Aileron2 Aileron2 Flap Flap Flap Flap ---- Flap2 ---- Rudder2
7 AUX6 AUX6 Aileron2 Aileron2 Aileron2 Aileron2 ---- Flap3 ---- Flap
8 AUX5 AUX5 AUX5 AUX5 Flap2 Flap2 ---- Flap4 ---- Flap2
VC1 Elevator Elevator Elevator Elevator Elevator Elevator ---- Elevator ---- Elevator
VC2 Camber Camber Camber Camber Camber Camber ---- Camber ---- Camber
VC3 AUX1 AUX1 AUX1 %XWWHUÁ\ AUX1 %XWWHUÁ\ ---- %XWWHUÁ\ ---- %XWWHUÁ\
VC4 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 ---- AUX1 ---- AUX1
Ɣ9&aDUHYLUWXDOFKDQQHOVZLWKRXWUHFHLYHURXWSXW)RUPRUHLQIRUPDWLRQVHHWKHGHVFULSWLRQRIWKH
)XQFWLRQPHQXRIWKH/LQNDJH0HQX
Ɣ7KHZLQJW\SHVZKLFKFDQEHVHOHFWHGGHSHQGRQWKH)$667PRGH0XOWLFKRUFKVHOHFWHG
7KHVHZLQJW\SHVDUHDYDLODEOHRQERWKWKH0XOWLFKDQGFKPRGH+RZHYHUWKHFKGRHVQ
WZRUNRQWKHFKPRGH
7KLVZLQJW\SHLVDYDLODEOHRQERWKWKH0XOWLFKDQGFKPRGH+RZHYHUVLQFHWKHFKGRHVQ
WZRUNRQWKHFKPRGHSOHDVH
DVVLJQWKHÀDSWRDQRWKHUFKDQQQHOZKLFKLVQ
WXVHG
7KHVHZLQJW\SHVDUHDYDLODEOHRQWKH0XOWLFKPRGHRQO\
5HFHLYHUDQG6HUYR,QVWDOODWLRQ! 31
+HOLFRSWHU
5 Gyro Gyro
6 Pitch Pitch
7 Governor Governor
8 Elevator2 Needle
32 5HFHLYHUDQG6HUYR,QVWDOODWLRQ!
3UHFDXWLRQVZKHQPRXQWLQJWKHUHFHLYHUDQGVHUYRV
)ROORZWKHVHJXLGHOLQHVWRSURSHUO\PRXQWWKHVHUYRVUHFHLYHUDQGEDWWHU\
7RFHQWHUWKHVHUYRVFRQQHFWWKHPWRWKHUHFHLYHU
and turn on the transmitter and receiver. Center Slack in the lead wire.
WKHWULPVRQWKHWUDQVPLWWHUWKHQ¿QGWKHDUPWKDW
ZLOOEHSHUSHQGLFXODUWRWKHSXVKURGZKHQSODFHG
5HFHLYHUDQG6HUYR,QVWDOODWLRQ! 33
5HFHLYHU
V$QWHQQD,QVWDOODWLRQ
<RXZLOOQRWHWKDWWKH5+6GLIIHUVLQDSSHDUDQFHIURPWKHVWDQGDUG)XWDEDUHFHLYHU7KLVUHFHLYHU
LQFRUSRUDWHWZRVHSDUDWHDQWHQQDVLQWRWKHLUGHVLJQZKLFKHQDEOHVWKHPWRUHFHLYHWKHUDGLRIUHTXHQF\
WUDQVPLVVLRQDWWZRGLIIHUHQWORFDWLRQV
*Must be kept as straight as possible.
Antenna
Coaxial cable
R6008HS Receiver
)XWDED
VGXDODQWHQQDGLYHUVLW\WKHQVHDPOHVVO\VHOHFWVWKHEHVWVLJQDOUHFHSWLRQEHWZHHQWKHVHDQWHQQDV
to ensure that there is no loss of signal.
To obtain the best results of the diversity This is not a critical figure, but the most
IXQFWLRQSOHDVHUHIHUWRWKHIROORZLQJLQVWUXFWLRQV important thing is to keep the antennas
away from each other as much as possible.
1. The two antennas must be kept as straight as
possible. Otherwise it will reduce the effective Larger models can have large metal objects
range. that can attenuate the RF signal. In this case
the antennas should be placed at both
2. The two antennas should be placed at 90 sides of the model. Then the best RF signal
degrees to each other. FRQGLWLRQLVREWDLQHGDWDQ\Á\LQJDWWLWXGH
3. The antennas must be kept away from
conductive materials, such as metal, carbon
and fuel tank by at least a half inch. The
coaxial part of the antennas does not need
to follow these guidelines, but do not bend it
in a tight radius.
4. Keep the antennas away from the motor,
ESC, and other noise sources as much as
possible.
Antenna Antenna
7KHWZRDQWHQQDVVKRXOGEHSODFHGDWGHJUHHVWRHDFKRWKHU
7KHPDLQSXUSRVHRIWKHSKRWRGHPRQVWUDWHVKRZWKHDQWHQQDVKRXOGEHSODFHG
5HFHLYHU9LEUDWLRQDQG:DWHUSURR¿QJ7KHUHFHLYHUFRQWDLQVSUHFLVLRQHOHFWURQLFSDUWV%HVXUH
WRDYRLGYLEUDWLRQVKRFNDQGWHPSHUDWXUHH[WUHPHV)RUSURWHFWLRQZUDSWKHUHFHLYHULQIRDP
UXEEHURURWKHUYLEUDWLRQDEVRUELQJPDWHULDOV,WLVDOVRDJRRGLGHDWRZDWHUSURRIWKHUHFHLYHU
E\SODFLQJLWLQDSODVWLFEDJDQGVHFXULQJWKHRSHQHQGRIWKHEDJZLWKDUXEEHUEDQGEHIRUH
ZUDSSLQJLWZLWKIRDPUXEEHU,I\RXDFFLGHQWDOO\JHWPRLVWXUHRUIXHOLQVLGHWKHUHFHLYHU\RX
PD\H[SHULHQFHLQWHUPLWWHQWRSHUDWLRQRUDFUDVK,ILQGRXEWUHWXUQWKHUHFHLYHUWRRXUVHUYLFH
center for service.
34 5HFHLYHUDQG6HUYR,QVWDOODWLRQ!
02'(/%$6,&6(77,1*352&('85(
$LUSODQHJOLGHUEDVLFVHWWLQJSURFHGXUH
The T8FG is capable of storing data for up to 20 ŏ ,I WKH GLUHFWLRQ RI WKH VHUYR LV LQFRUUHFW DGMXVW
models in its internal memory. Additional model the direction with the Reverse function of the
Linkage Menu.
data can also be saved to an optional SD card.
The currently selected model name is displayed
LQWKHFHQWHURIWKHKRPHVFUHHQ%HIRUHÀ\LQJDQG
EHIRUHFKDQJLQJDQ\VHWWLQJVDOZD\VFRQILUPWKH
model name.
:KHQ D QHZ PRGHO LV DGGHG WKH 0RGHO W\SH ŏ $GMXVW WKH QHXWUDO SRVLWLRQ DQG FRQWURO
select screen and FASST mode/Area select setup surface angle with the linkage, and fine
tune them with the Sub-Trim and End Point
VFUHHQDXWRPDWLFDOO\DSSHDU3OHDVHEHDZDUHWKDW
functions (angle adjustment). To protect the
WKHWUDQVPLWWHUZLOOVWRSWUDQVPLWWLQJWHPSRUDULO\ linkage, a limit position can also be set with
ZKHQ\RXFKDQJHWKHPRGHO the End Point function. The End Point function
can adjust the amount of up/down and left/
right movement and limit of each channel.
0RGHOW\SHVHOHFWLRQ
Select the model type matched to the aircraft 7KURWWOHFXWVHWWLQJ$LUSODQH
ZLWKWKH0RGHO7\SHVHOHFWIXQFWLRQRIWKH/LQNDJH 7KURWWOHFXWFDQEHSHUIRUPHGZLWKRQHWRXFKE\D
0HQX)RUDQDLUSODQHVHOHFWWKHPRGHOW\SHIURP VZLWFKZLWKRXWFKDQJLQJWKHWKURWWOHWULPSRVLWLRQ
among the 2 types: airplane and glider. And then
6HWWKURWWOHFXWZLWKWKH7KURWWOH&XWIXQFWLRQRI
VHOHFWWKHZLQJW\SHDQGWKHWDLOW\SHPDWFKHGWR
WKH/LQNDJH0HQX$IWHUDFWLYDWLQJWKHWKURWWOHFXW
the aircraft.
IXQFWLRQDQGVHOHFWLQJWKHVZLWFKDGMXVWWKHWKURWWOH
position so that the carburetor becomes fully closed.
)RU VDIHW\ WKH WKURWWOH FXW IXQFWLRQ RSHUDWHV WKH
WKURWWOHVWLFNLQWKHRUOHVVVORZVLGHSRVLWLRQ
)XVHODJHOLQNDJH
&RQQHFWWKHDLOHURQVHOHYDWRUVWKURWWOHUXGGHU
HWF LQ DFFRUGDQFH ZLWK WKH PRGHO
V LQVWUXFWLRQ
manual. For a description of the connection
0RGHO%DVLF6HWWLQJ3URFHGXUH! 35
,GOHGRZQVHWWLQJ$LUSODQH
7KHLGOLQJVSHHGFDQEHORZHUHGZLWKRQHWRXFK
E\ D VZLWFK ZLWKRXW FKDQJLQJ WKH WKURWWOH WULP
SRVLWLRQ3HUIRUPWKLVVHWWLQJZLWKWKH,GOH'RZQ
IXQFWLRQRIWKH/LQNDJH0HQX$IWHUDFWLYDWLQJWKH
,GOH'RZQIXQFWLRQDQGVHOHFWLQJWKHVZLWFKDGMXVW $GGLWLRQRIÀLJKWFRQGLWLRQV*OLGHU
WKH LGOH GRZQ VSHHG )RU VDIHW\ WKH LGOH GRZQ The Condition Select function automatically
IXQFWLRQDFWVRQO\ZKHQWKHWKURWWOHVWLFNLVLQWKH DOORFDWHV WKH QRUPDO FRQGLWLRQ 1250$/ IRU
ORZHVWSDUWRILWVWKURZ HDFKPRGHO1250$/LVWKHGHIDXOWFRQGLWLRQDQG
:KLOH WKH7KURWWOH &XW IXQFWLRQ LV LQ RSHUDWLRQ WKH ,GOH LVWKHRQO\RQHDFWLYHZKHQDQHZPRGHOW\SHLV
'RZQIXQFWLRQGRHVQRWZRUN GH¿QHG
,I\RXZDQWWRDGGÀLJKWFRQGLWLRQVSOHDVHUHIHU
WRDGHVFULSWLRQRIWKH&21',7,21IXQFWLRQS
6. D/R function
'5 IXQFWLRQ LV XVHG WR DGMXVW WKH WKURZ DQG
7KH 1250$/ LV DOZD\V RQ DQG UHPDLQV RQ XQWLO RWKHU
RSHUDWLRQ FXUYH RI WKH VWLFN IXQFWLRQV DLOHURQ
FRQGLWLRQV DUH DFWLYDWHG E\ VZLWFKHV VWLFN SRVLWLRQV HWF
HOHYDWRU UXGGHU DQG WKURWWOH IRU HDFK VZLWFK 3OHDVHUHIHUWRWKHVHFWLRQHQWLWOHG6ZLWFK6HOHFWLRQ0HWKRG
SRVLWLRQDLUSODQHRUHDFKÀLJKWFRQGLWLRQJOLGHU IRUDGGLWLRQDOLQIRUPDWLRQRQKRZWRGRVR
7KLVLVQRUPDOO\XVHGDIWHUWKHPRGHOHUKDVGH¿QHG *It is possible to customize the activation of the flight
WKH PD[LPXP WKURZ GLUHFWLRQV LQ WKH (QG 3RLQW conditions.
settings. *The Condition Delay can be programmed for each channel.
$LUSODQH 7KH &RQGLWLRQ 'HOD\ LV XVHG WR FKDQJH WKH VHUYR WKURZ
VPRRWKO\ZKHQVZLWFKLQJFRQGLWLRQV
*OLGHU
$LUEUDNH$LUSODQH
7KLV IXQFWLRQ LV XVHG ZKHQ DQ DLUEUDNH LV
QHFHVVDU\ ZKHQ WDNLQJ RII RU GLYLQJ HWF 3OHDVH
note: this menu item is only available under certain
ZLQJFRQ¿JXUDWLRQV)RUH[DPSOHLWZLOOQRWDSSHDU
LIDVLQJOHDLOHURQZLQJW\SHKDVEHHQVHOHFWHG
7KHSUHVHWHOHYDWRUDQGÀDSRIIVHWDPRXQWFDQ
EHDFWLYDWHGE\DVZLWFK
7KHRIIVHWDPRXQWRIWKHDLOHURQHOHYDWRUDQG
IODS VHUYRV FDQ EH DGMXVWHG DV QHHGHG$OVR WKH
VSHHGRIWKHDLOHURQHOHYDWRUDQGÀDSVHUYRVFDQ
EHDGMXVWHG<RXFDQDOVRVHWWKH$XWR0RGHZKLFK
ZLOO OLQN$LUEUDNH WR D VWLFN VZLWFK RU GLDO$
VHSDUDWHVWLFNVZLWFKRUGLDOFDQDOVREHVHWDVWKH
212))VZLWFK
36 0RGHO%DVLF6HWWLQJ3URFHGXUH!
+HOLFRSWHUEDVLFVHWWLQJSURFHGXUH
7KLVVHFWLRQRXWOLQHVH[DPSOHVRIXVHRIWKHKHOLFRSWHUIXQFWLRQVRIWKH7)*$GMXVWWKHDFWXDOYDOXHV
etc. to match the fuselage used.
0RGHO%DVLF6HWWLQJ3URFHGXUH! 37
6HUYR&RQQHFWLRQ 7KURWWOH3LWFKFXUYHVHWWLQJ
&RQQHFW WKH WKURWWOH UXGGHU DLOHURQ HOHYDWRU 7KLV IXQFWLRQ DGMXVWV WKH WKURWWOH RU SLWFK
SLWFK DQG RWKHU VHUYRV LQ DFFRUGDQFH ZLWK WKH operation curve in relation to the movement of the
kit instruction manual. For a description of the throttle stick for each condition.
FRQQHFWLRQ PHWKRG VHH 5HFHLYHU DQG 6HUYRV
Connection".
Note: The channel assigned to each function
can be checked at the Function menu of the
Linkage Menu.
7KURWWOHFXUYHVHWWLQJH[DPSOH!
$FWLYDWHWKHWKURWWOHFXUYHRIHDFKFRQGLWLRQZLWK
WKHFRQGLWLRQVHOHFWVZLWFK
ŏ1RUPDO FXUYH DGMXVWPHQW
ŏ ,I WKH GLUHFWLRQ RI RSHUDWLRQ RI WKH VHUYR Normal curve creates a basic throttle curve
is incorrect, use the Reverse function of centered near hovering. This curve is adjusted
the Linkage Menu. Also use the swash AFR together with the pitch curve (Normal) so that the
function in other than the H-1 mode. engine speed is constant and up/down control is
easiest.
ŏ,GOH XS FXUYH DGMXVWPHQW
The low side Throttle curve creates a curve
matched for aerobatics (loop, roll, 3D, etc.).
ŏ7KURWWOH KROG FXUYH DGMXVWPHQW
The curve is not used when performing auto rotation
dives.
&RQÀUP WKDW WKH UDWH RI WKH VORZHVW SRVLWLRQ RI
WKH VWLFN LV LQLWLDO VHWWLQJ
38 0RGHO%DVLF6HWWLQJ3URFHGXUH!
6. D/R function IRUHDFKFRQGLWLRQ$WLQLWLDOVHWWLQJWKLVIXQFWLRQ
'5 IXQFWLRQ LV XVHG WR DGMXVW WKH WKURZ DQG LVLQWKH,1+VWDWH7RXVHLWVHWLWWRWKH21
RSHUDWLRQFXUYHRIDLOHURQHOHYDWRUDQGUXGGHUIRU VWDWH
each condition. 6HWWLQJH[DPSOH!
)RU WKURWWOH DQG SLWFK FXUYH VHWWLQJV UHIHU WR WKH DIRUH
$FWLYDWHWKHPL[LQJFXUYHRIHDFKFRQGLWLRQZLWK
mentioned "Throttle/Pitch curve setting"
WKHFRQGLWLRQVHOHFWVZLWFK
7KLVLVQRUPDOO\XVHGDIWHU(QG3RLQWKDVGH¿QHG
A curve setting example is shown below.
WKHPD[LPXPWKURZGLUHFWLRQV
ŏ3LWFK WR 58' PL[LQJ FXUYH 1RUPDO
Use the hovering system and set this curve to
match take off and landing and vertical climb at a
constant speed.
ŏ3LWFK WR 58' PL[LQJ ,GOH XS
Use this curve in 540º stall turn, loop, and rolling stall
*\URVHQVLWLYLW\DQGPRGHVZLWFKLQJ turn, and adjust it so the fuselage is facing straight
ahead when heading into the wind.
7KH J\UR VHQVLWLYLW\ DQG PRGH VZLWFKLQJ
ŏ3LWFK WR 58' PL[LQJ +ROG
IXQFWLRQLVXWLOL]HGWRDGMXVWWKHJ\URPL[LQJRIWKH
This function is set so that the fuselage is facing
PRGHODQGFDQEHVHWIRUHDFKFRQGLWLRQ straight ahead at straight line auto rotation. The
pitch of the tail rotor becomes nearly 0º.
7KURWWOHKROGVHWWLQJ
,IWKURWWOHKROGLVQHFHVVDU\SOHDVHUHIHUWRWKH7+5+2/'
IXQFWLRQS
:LWKWKURWWOHVWLFNDWLGOHDGMXVWWKHFXWSRVLWLRQXQWLOWKH
HQJLQH FRQVLVWHQWO\ VKXWV RII EXW WKURWWOH OLQNDJH LV QRW
binding.
6ZDVK0L[FRUUHFWVDLOHURQHOHYDWRUDQG
8VH WKLV IXQFWLRQ ZKHQ \RX ZDQW WR VXSSUHVV SLWFKLQWHUDFWLRQ
WKH WRUTXH JHQHUDWHG E\ WKH FKDQJHV LQ WKH SLWFK
7KH VZDVK PL[ IXQFWLRQ LV XVHG WR FRUUHFW WKH
and speed of the main rotor during pitch operation.
VZDVK SODWH LQ WKH DLOHURQ /HIW5LJKW &\FOLF
$GMXVW LW VR WKDW WKH QRVH GRHV QRW VZLQJ LQ WKH
DQG HOHYDWRU )RUZDUG$IW &\FOLF GLUHFWLRQ
UXGGHUGLUHFWLRQ+RZHYHUZKHQXVLQJDKHDGLQJ
corresponding to each operation of each condition.
KROGJ\UROLNHWKRVHVKRZQDERYHGRQRWXVH3LWFK
to rudder mixing.
$FWLYDWHWKH3LWFKWRUXGGHU3LW!58'PL[LQJ
IXQFWLRQIURPWKH0RGHO0HQXDQGVHWWKHFXUYH
0RGHO%DVLF6HWWLQJ3URFHGXUH! 39
7KURWWOHPL[LQJVHWWLQJ
*If throttle mixing is necessary for a compensation for
VORZLQJRIHQJLQHVSHHGFDXVHGE\VZDVKSODWHRSHUDWLRQ
GXULQJ DLOHURQ RU HOHYDWRU RSHUDWLRQ SOHDVH UHIHU WR WKH
7+5277/(0,;IXQFWLRQS
2WKHUVSHFLDOPL[LQJV
ŏ3LWFK WR 1HHGOH PL[LQJ
This mixing is used with engines with a design which
allows needle control during flight (fuel-air mixture
adjustment). A needle curve can be set.
ŏ*RYHUQRU PL[LQJ
This mixing is dedicated governor mixing when a
GV-1 (governor) is used.
40 0RGHO%DVLF6HWWLQJ3URFHGXUH!
SYSTEM MENU
7KH 6\VWHP 0HQX VHWV XS IXQFWLRQV RI WKH
transmitter: This does not set up any model data.
<SensorTouch™>
ŏ6HOHFW >6<67(0 0(18@ Scrolling
and return to the home ŏ0RYLQJ FXUVRU
screen by touching the
RTN button.
6\VWHP0HQXIXQFWLRQVWDEOH
[TRAINER]: Starts and sets the trainer system.
>',63/$<@/&'DQGEDFNOLJKWDGMXVWPHQW
>86(51$0(@8VHUQDPHUHJLVWUDWLRQ
[H/W SET]: H/W reverse and stick mode
>,1)2@'LVSOD\VWKHSURJUDPYHUVLRQ6'FDUGLQIRUPDWLRQSURGXFW,'DQGODQJXDJHVHOHFWLRQ
)XQFWLRQVRI6\VWHP0HQX! 41
Trainer system starting and setting
TRAINER
The Trainer function makes it possible for the :KHQXVLQJ7)*DVWKHVWXGHQWWUDQVPLWWHUWKH
LQVWUXFWRUWRFKRRVHZKLFKIXQFWLRQV
and channels trainer function is not used.
DUHWREHXVHGIRULQVWUXFWLRQPDNLQJLWSRVVLEOHWR
You can select the operation mode for each channel.
match the training ability to the student's skill level. 12500,;)81&2))
7ZRWUDQVPLWWHUVPXVWEHFRQQHFWHGE\DQRSWLRQDO
WUDLQHUFRUGDQGWKHLQVWUXFWRU
VWUDQVPLWWHUVKRXOG NOTE: This trainer system can be used in the
EHSURJUDPPHGIRUWUDLQHURSHUDWLRQDVGHVFULEHG following manner;
EHORZ 1. With the T8FG transmitter and a conventional
transmitter, if the channel order is different,
:KHQWKH,QVWUXFWRUDFWLYDWHVWKHWUDLQHUVZLWFK it is necessary to match the channel order
WKHVWXGHQWKDVFRQWURORIWKHDLUFUDIWLI0,;RU before using this function.
)81&PRGHLVWXUQHGRQWKH,QVWUXFWRUFDQPDNH You can select the channel of input data
FRUUHFWLRQVZKLOHWKHVWXGHQWKDVFRQWURO:KHQ from student's transmitter in the "FUNC" or
"MIX" mode.
WKHVZLWFKLVUHOHDVHGWKH,QVWUXFWRUUHJDLQVFRQWURO
This is very useful if the student gets the aircraft 2. When the T8FG is used as the instructor’s
transmitter, set the modulation mode of the
into an undesirable situation. student’s transmitter to PPM.
You can select the channel input data from the If being used as the student, T8FG can be
VWXGHQW WUDQVPLWWHU DV HLWKHU )81& RU 0,; connected to the instructor's transmitter which
mode. These options make it easier to use a variety the PPM mode as the student's modulation
RIUHFHLYHUVWUDQVPLWWHUVHWF mode is required. T8FG always sends PPM
mode signal from the trainer jack.
,WLVDOVRSRVVLEOHWRXVHWKHYLUWXDOFKDQQHO9& 3. Be sure that all channels work correctly in
DW³)81&´RU³0,;´PRGHRUWRXVHWKHWUDLQHU ERWKWUDQVPLWWHUVEHIRUHÁ\LQJ
V\VWHPZLWKÀ\LQJZLQJDLUSODQHV
7)*7)*VSHFLDOWUDLQHUFDEOH
8VH WKH7)*7)* VSHFLDO WUDLQHU FDEOH )870 ZKHQ XVLQJ WKH7)* RU
7)*WUDQVPLWWHUDWWKHWUDLQHUIXQFWLRQLQVWUXFWRUVLGH2SHUDWLRQPD\QRWEHQRUPDOZLWK
a conventional trainer cable.
,IWKH7)*RU7)*WUDQVPLWWHULVXVHGDVWKHVWXGHQWWUDQVPLWWHUZKHQWKHLQVWUXFWRUWUDQVPLWWHULVQRWD
7)*RU7)*DFRQYHQWLRQDOWUDLQHUFDEOHPD\EHXVHG
Instructor Student Trainer cable
T4EX, T6EX, T7C, T9C T12FG special trainer cable
T12Z, T14MZ, FX-40 Conventional trainer cable (Rect. - Rect.)
T8FG, T12FG
T4V Conventional trainer cable (Rect. - Round)
T6X, T7U, T8U, and T9Z are not applicable.
Other than Conventional trainer cable (Rect. - Rect.) or
T8FG, T12FG
T8FG, T12FG Conventional trainer cable (Rect. - Round)
7KHGLUHFWLRQWKDWWKH7)*7)*VSHFLDOWUDLQHUFDEOHFRQQHFWVLVIL[HG&RQQHFW
WKHLQVWUXFWRUFDEOHDGDSWHUFRQQHFWRURIWKHFDEOHWRWKHLQVWUXFWRU7)*RU7)*DQG
FRQQHFWWKHVWXGHQWFRQQHFWRUWRWKHVWXGHQWWUDQVPLWWHU,IWKHFDEOHLVFRQQHFWHGLQUHYHUVH
WKHVWXGHQW
VWUDQVPLWWHUSRZHUZLOOQRWEHWXUQHGRQHYHQLIWKHLQVWUXFWRUVLGHSRZHULVVHW
WR21
,IWKHLQVWUXFWRUVLGH7)*RU7)*WUDLQHUIXQFWLRQLVQRWHQDEOHGWKHVWXGHQW
VSRZHU
ZLOOQRWEHWXUQHG21HYHQLIWKHFRQQHFWLRQGLUHFWLRQLVFRUUHFW
42 )XQFWLRQVRI6\VWHP0HQX!
ŏ 6HOHFW >75$,1(5@ LQ WKH 6\VWHP PHQX DQG HQWHU WKH
setup screen shown below by touching the RTN
button.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the System ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
2SHUDWLQJPRGHVHOHFWLRQ
(Setup screen page 1-3)
2. Move the cursor to the [ACT] or [12/8CH]
item and touch the RTN button to switch to
the data input mode.
3. Select the mode by scrolling the touch
sensor. The display blinks. Touch the RTN
button to change the mode. (To terminate
the mode change, touch the S1 button.) 1. Move the cursor to the [MODE] item of the
channel you want to change and touch the
RTN button to switch to the data input mode.
"ACT": Enable operation by changing to [OFF] 2. Select the mode by scrolling the touch
or [ON]. sensor. The display blinks. Touch the RTN
"12/8 CH": When the student uses the T14MZ, button to change the mode. (To terminate
T12Z, T12FG or FX-40, select [12CH]. Otherwise the mode change, touch the S1 button.)
select [8CH].
"MODE": Select the desired operation mode
If changing the trainer switch: for each channel.
4. Move the cursor to the [SW] item and touch
the RTN button to access the switch setup 12507KHPRGHOLVFRQWUROOHGE\VLJQDOVIURPWKHVWXGHQW
screen. transmitter.
(See "Switch selection method" at the end of 0,; PRGH7KH PRGHO LV FRQWUROOHG E\ VLJQDOV IURP WKH
LQVWUXFWRU DQG VWXGHQW WUDQVPLWWHUV 5HVHW WKH VWXGHQW
V
this manual for selection method details.)
PRGHOGDWDWRWKHGHIDXOWFRQGLWLRQ
)81&PRGHIXQFWLRQPRGH7KHPRGHOLVFRQWUROOHGE\
"SW": Select the desired switch. VLJQDOV IURP WKH VWXGHQW WUDQVPLWWHU ZLWK WKH LQVWUXFWRU
V
Initial setting: SH VHWWLQJ 5HVHW WKH VWXGHQW
V PRGHO GDWD WR WKH GHIDXOW
FRQGLWLRQ
2))2QO\WKHLQVWUXFWRUVLGHRSHUDWHV
7KHVZLWFKPRGHFDQDOVREHVHOHFWHGZKHQVHWWLQJWKH21
SRVLWLRQRQWKHVZLWFKVHWXSVFUHHQ:KHQ>$/7(51$7(
2))@LVVHOHFWHGQRUPDO212))RSHUDWLRQLVSHUIRUPHG
:KHQ>$/7(51$7(21@LVVHOHFWHGWKHWUDLQHUIXQFWLRQ
$GMXVWLQJWKHVWXGHQW
VUDWH
LV DOWHUQDWHO\ WXUQHG RQ DQG RII HDFK WLPH WKH VZLWFK LV
7KHVHWWLQJDERYHDOORZVVHWWLQJRIWKHVHUYRWKURZUHODWLYH
RSHUDWHG7KLV DOORZV DOWHUQDWH 212)) VZLWFKLQJ HYHQ WR WKH DPRXQW RI VWXGHQW VLGH RSHUDWLRQ ZKHQ >0,;@ RU
ZKHQDPRPHQWDU\VZLWFK6+LVXVHG >)81&@ZDVVHOHFWHG
)XQFWLRQVRI6\VWHP0HQX! 43
1. Move the cursor to the [RATE] item of the
channel you want to change and touch the
RTN button to switch to the data input mode.
2. Adjust the rate by scrolling the touch sensor.
&KDQJLQJWKHVWXGHQW
VFKDQQHO
7KHVHWWLQJDERYHDOORZVVHWWLQJRIWKHFKDQQHODVVLJQPHQW
RIVWXGHQWVLGHZKHQ>0,;@RU>)81&@ZDVVHOHFWHG
1. Move the cursor to the [STU. CH] item of the
channel you want to change and touch the
RTN button to switch to the data input mode.
2. Select the channel by scrolling the touch
sensor. The display blinks. Touch the RTN
button to change the channel. (To terminate
the mode change, touch the S1 button.)
44 )XQFWLRQVRI6\VWHP0HQX!
LCD and back-light adjustment
',63/$<
/&'FRQWUDVWEDFNOLJKWEULJKWQHVVDQGEDFN
OLJKWRIIWLPHUDGMXVWPHQWDUHSRVVLEOH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the System ŏ0RYLQJ FXUVRU
menu by touching the ŏ$GMXVWLQJ YDOXH
RTN button.
/&'FRQWUDVWDGMXVWPHQW
:KHQ\RXZDQWWRUHVHWWKHYDOXHWRWKHLQLWLDOVWDWHWRXFK
the RTN button for one second.
1. Select "CONTRAST" and touch the RTN button
to switch to the data input mode and adjust
the contrast by scrolling the touch sensor. 2. Touch the RTN button to end adjustment and
return to the cursor mode.
)XQFWLRQVRI6\VWHP0HQX! 45
User name registration
USER NAME
7KLVIXQFWLRQDOORZVWKHPRGHOHUVWRFKDQJHWKH
T8FG user name.
$QDPHRIXSWRFKDUDFWHUVFDQEHHQWHUHGDVWKHXVHU
name. Please note that a space is also counted as one
character.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the System ŏ0RYLQJ FXUVRU
menu by touching the
RTN button.
[Adding a character]
When a character is selected from the (Character list 3/3)
character list and the RTN button is touched,
that character is added at the position
immediately after the cursor.
$QDPHRIXSWRFKDUDFWHUVORQJFDQEHHQWHUHGDVWKH
XVHUQDPH$VSDFHLVDOVRFRXQWHGDVFKDUDFWHU
46 )XQFWLRQVRI6\VWHP0HQX!
Hardware reverse and stick mode
H/W SETTING
+:UHYHUVH Stick mode
This function reverses the operation direction of This function changes the stick mode of
WKHVWLFNVVZLWFKHVWULPPHUOHYHUVDQGNQREV transmitter.
Note: This setting reverses the actual operation Note: This will not change the throttle ratchet,
signal, but does not change the display etc. Those are mechanical changes that
indicators. Use the Normal mode as long as must be performed by a Futaba service
there is no special reason to use the Reverse center.
mode. Note: After changing the mode, these changes
are only applied to new models. It is not
applied to an existing model.
ŏ 6HOHFW >+: 6(7@ DW WKH V\VWHP PHQX DQG DFFHVV
the setup screen shown below by touching the
RTN button.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the System ŏ0RYLQJ FXUVRU
menu by touching the
RTN button.
2SHUDWLRQGLUHFWLRQUHYHUVDOPHWKRG &KDQJLQJVWLFNPRGH
1. Select [H/W REVERSE] and access the setup 1.Select [STICK MODE] and access the setup
screen shown below by touching the RTN screen shown below by touching the RTN
button. button.
)XQFWLRQVRI6\VWHP0HQX! 47
Displays the program version, SD card information, and product ID.
INFO
7KH7)*V\VWHPSURJUDPYHUVLRQLQIRUPDWLRQ 7KH ODQJXDJH GLVSOD\HG LQ KRPH PHQX DQG
6' FDUG LQIRUPDWLRQ FXUUHQW DQG PD[LPXP setup screen is selectable.
QXPEHURIPRGHOGDWDDQGRWKHU¿OHVDQGSURGXFW
ID are displayed on the Information screen.
:KHQWKH6'FDUGLVQRWLQVHUWHGWKH6'FDUGLQIRUPDWLRQLV
not displayed.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the System ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button.
,QIRUPDWLRQ /DQJXDJHVHOHFWLRQ
"PRODUCT": Product ID number 1. Move the cursor to the "LANGUAGE" item
"VERSION": T8FG system program version and touch the RTN button to switch to the
information data input mode.
"CARD SIZE": Current/Maximum number of 2. Change the language by scrolling the touch
PRGHO GDWD DQG RWKHU ÀOHV 6' FDUG sensor. The display blinks. When the RTN
button is touched, the language is changed.
(To terminate the mode change, turn the
EDIT dial or push the S1 button.)
48 )XQFWLRQVRI6\VWHP0HQX!
FUNCTIONS OF LINKAGE MENU
7KH /LQNDJH 0HQX LV PDGH XS RI IXQFWLRQV 7KHIXQFWLRQVZKLFKFDQEHVHOHFWHGGHSHQGRQ
ZKLFK SHUIRUP PRGHO DGGLWLRQ PRGHO W\SH WKH PRGHO W\SH$ W\SLFDO PHQX VFUHHQ LV VKRZQ
VHOHFWLRQIUHTXHQF\VHWWLQJHQGSRLQWVHWWLQJDQG EHORZ
other model basic settings.
<SensorTouch™>
ŏ6HOHFW >/,1.$*( 0(18@ Scrolling
and return to the home ŏ0RYLQJ FXUVRU
screen by touching the
RTN button.
/LQNDJH0HQXIXQFWLRQVWDEOH
>6(592@'LVSOD\VWKHVHUYRWHVWDQGRSHUDWLRQSRVLWLRQ
>02'(/6(/@0RGHODGGLWLRQFDOOGHOHWLRQFRS\PRGHOQDPHVHWWLQJ
>02'(/7<3(@0RGHOW\SHZLQJW\SHVZDVKW\SHHWFVHOHFWLRQ
>)5(48(1&<@)$667PRGHVHOHFWLRQDQGDUHDPRGHVHOHFWLRQ
>)81&7,21@&KDQQHODVVLJQPHQWRIHDFKIXQFWLRQFDQEHFKDQJHG
>68%75,0@$GMXVWVWKHQHXWUDOSRVLWLRQRIHDFKVHUYR
[REVERSE]: Reverses the servo travel direction
>)$,/6$)(@)DLOVDIHIXQFWLRQDQGEDWWHU\IDLOVDIHIXQFWLRQVHWWLQJ
>(1'32,17@6HUYRWUDYHODGMXVWPHQWDQGOLPLWVHWWLQJ
>7+5&87@6WRSVWKHHQJLQHVDIHO\DQGHDVLO\DLUSODQHDQGKHOLFRSWHURQO\
>,'/('2:1@/RZHUVWKHLGOHVSHHGRIWKHHQJLQHDLUSODQHRQO\
>6:$6+5,1*@/LPLWVWKHVZDVKSODWHWUDYHOWRZLWKLQD¿[HGUDQJHKHOLFRSWHURQO\
>6:$6+@6ZDVK$)5DQGOLQNDJHFRUUHFWLRQIXQFWLRQKHOLFRSWHURQO\
>776(7@&RQWUROVWHSDPRXQWDQGPRGHVHOHFWLRQRIWKHGLJLWDOWULP
>'$7$5(6(7@0RGHOPHPRU\VHWGDWDUHVHW
)XQFWLRQVRI/LQNDJH0HQX! 49
Servo Test & Graph Display / Displays servo positions.
SERVO MONITOR
This is used for testing servo movement. The “Neutral Test” is good for finding the
³0RYLQJ 7HVW´ UHSHWLWLRQ PRGH DQG ³1HXWUDO neutral position of a servo horn.
7HVW´¿[HGSRVLWLRQPRGHDUHDYDLODEOH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button.
6HUYRWHVWRSHUDWLRQ
1. Move the cursor to the [OFF] item and touch
the RTN button to switch to the data input
mode.
Select the test mode by scrolling the touch
sensor and touch the RTN button. The display
blinks. Touch the RTN button to change the
mode. (To terminate mode change, touch
the S1 button.)
50 )XQFWLRQVRI/LQNDJH0HQX!
The Model Selection function performs model addition, selection,
MODEL SELECT deletion, copy, and model name setting.
This function is used to load the settings of the DOZD\VDSSHDUVLQWKHGLVSOD\VFUHHQ
GHVLUHGPRGHOLQWRWKH7)*¶VPHPRU\ 7KH&RS\IXQFWLRQLVXVHGWRFRS\SDUDPHWHUV
The settings may be selected from either the VHWWLQJV HWF IURP RQH PRGHO GDWD LQWR D VHFRQG
WUDQVPLWWHU¶VLQWHUQDOPHPRU\RUDQ6'FDUG0% memory. It may be used for getting a head-start on
*%5HPHPEHUWKDWXSWRPRGHOPHPRULHVDUH VHWWLQJXSPRGHOVZLWKDOPRVWWKHVDPHVHWWLQJVRQO\
available in the transmitter. GLIIHUHQFHVQHHGWREHPRGL¿HGLQVWHDGRIHQWHULQJWKH
The name of the model stored in the transmitter and FRPSOHWHPRGHOIURPVFUDWFK$OVRWKLVIXQFWLRQPD\
the SD card may be changed. This can be very useful be used to make a backup copy of a model setup before
to tell different models settings apart. Each model name any changes are made.
FDQEHDVORQJDVFKDUDFWHUVDQGWKHPRGHOQDPH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button.
Model deletion
7UDQVPLVVLRQVWRSVDQGWKHQVWDUWVLQWKHVWDWHRIWKHQHZ *The model stored in the transmitter memory or an SD card
model. can be deleted.
*The current model can not be deleted.
Model addition 1. Move the cursor to the save destination
display ("TX" or "CARD") and touch the RTN
$QHZPRGHOFDQEHDGGHGWRWKHWUDQVPLWWHUPHPRU\,WFDQ
button to switch to the data input mode.
not be added to the SD card.
Select the save destination by scrolling the
1. Move the cursor to [NEW]. touch sensor and touch the RTN button.
2. Touch the RTN button. A confirmation
)XQFWLRQVRI/LQNDJH0HQX! 51
[TX]: Transmitter memory 5. After the desired information has been input,
[CARD]: SD card select [ENTER] and touch the RTN button.
(To terminate input and return to the original
2. Move the cursor to the model you want to state, select [CANCEL] and touch the RTN
delete in the model list and then touch the button.)
RTN button.
3. Move the cursor to [DELETE].
7RXFK WKH 571 EXWWRQ :KHQ D FRQÀUPDWLRQ 0RGHOFRS\
message is displayed and the RTN button *A copy can be made of the model stored in the transmitter
is touched for one second, the model is memory or an SD card.
deleted.
1. If changing the location:
Move the cursor to the save destination
display ("TX" or "CARD") and touch the RTN
button to switch to the data input mode.
Select the save destination by scrolling the
touch sensor and touch the RTN button.
[TX]: Transmitter memory
0RGHOQDPHFKDQJH [CARD]: SD card
*The model name of the model stored in the transmitter 2. Select the model you want to copy in the
memory or a SD card can be changed. model list and then touch the RTN button.
1. If changing the location: 2. Move to [COPY].
Move the cursor to the save destination 3. Touch the RTN button.
display ("TX" or "CARD") and touch the RTN *The copy screen appears.
button to switch to the data input mode.
Select the save destination by scrolling the
touch sensor and touch the RTN button.
[TX]: Transmitter memory
[CARD]: SD card
2. Move the cursor to the model you want to 4. I f r e p l a c i n g t h e m o d e l s t o r e d i n t h e
change in the model list and then touch the transmitter memory:
RTN button. Move to [ADD-LIST] and touch the RTN button
3. Move to [RENAME]. to switch to the data input mode.
4. Touch the RTN button. Select the destination model by scrolling the
*The model name setup screen is displayed. touch sensor and touch the RTN button.
8VHUQDPHFDQGLGDWH [ADD-LIST]: adding the model to the list
[(model name)]: replacing the model
*The model stored in the SD card can be replaced.
If changing the location:
Move the cursor to the copy destination
display ("TX" or "CARD") and touch the RTN
4. Change the model name as described button to switch to the data input mode.
below: Select the save destination by scrolling the
[Moving cursor in the user name (candidate)] touch sensor and touch the RTN button.
6HOHFW >ł@ RU >ń@ DQG WRXFK WKH 571 EXWWRQ 5. Move to [COPY].
[Deleting a character] 7RXFK WKH 571 EXWWRQ :KHQ D FRQÀUPDWLRQ
message is displayed and the RTN button is
When [DELETE] is selected and the RTN button
touched for one second, the model data is
is touched, the character immediately after
copied.
the cursor is deleted.
[Adding a character]
When a character is selected from the
character list and the RTN button is touched,
that character is added at the position
immediately after the cursor.
$QDPHRIXSWRFKDUDFWHUVORQJFDQEHHQWHUHGDVWKH
PRGHOQDPH$VSDFHLVDOVRFRXQWHGDVRQHFKDUDFWHU
52 )XQFWLRQVRI/LQNDJH0HQX!
This function selects the model type from among airplane, helicopter,
02'(/7<3( and glider.
)RXUW\SHVRIPDLQZLQJVDQGWKUHHW\SHVRIWDLO swash type.) Be sure that you don’t mind
ZLQJVDUHDYDLODEOHIRUDLUSODQHV6L[VZDVKW\SHV losing this data, or back it up to another
memory using the copying functions.
are available for helicopters. Six types of main
ZLQJVDQGWKUHHW\SHVRIWDLOZLQJVDUHDYDLODEOHIRU When changing the helicopter swash type
within the following groups, you can leave
gliders. Functions and mixing functions necessary the settings other than the SWASH function.
for each model type are set in advance at the However, this is initialized when you change
factory. the swash type to the other swash type
Note: The Model Type function automatically group.
selects the appropriate output channels,
control functions, and mixing functions for the Swash type group A:
chosen model type. H-1, H-3, HR3, and HE3
When the Model Type selection command Swash type group B:
is accessed, all of the data in the active H-4, H-4X
memory is cleared (except the following
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button.
7KHGLVSOD\VFUHHQLVDQH[DPSOH7KH
VFUHHQGHSHQGVRQWKHPRGHOW\SH
7KHZLQJW\SHVZKLFKFDQEHVHOHFWHGGHSHQGRQWKH)$667
PRGH0XOWLFKRUFKVHOHFWHG
)XQFWLRQVRI/LQNDJH0HQX! 53
0RGHOW\SHVHOHFWLRQ$LUSODQH*OLGHU
Ɣ:LQJW\SH1RUPDO
>$,/)/3@DQG>$,/)/3@DUHDYDLODEOHRQWKHJOLGHUPRGHRQO\
Ɣ:LQJW\SH7DLOOHVVZLQJ
>$,/)/3@DQG>$,/)/3@DUHDYDLODEOHRQWKHJOLGHUPRGHRQO\
Ɣ5XGGHUW\SH
Ɣ7DLOW\SH
0RGHOW\SHVHOHFWLRQ+HOLFRSWHU
Ɣ6ZDVKW\SH
54 )XQFWLRQVRI/LQNDJH0HQX!
FASST mode selection and area mode selection
)5(48(1&<
FASST mode selection For the most up-to-date list of receivers and their
7KH UHFHLYHU W\SH ZLOO GHWHUPLQH ZKHWKHU \RX UHVSHFWLYH FRPSDWLELOLW\ SOHDVH UHIHU WR RXU ZHE
XWLOL]H08/7,RU&+VHWWLQJLQ)$667 site at: http://2.4gigahertz.com/receivers/index.html
MULTI/7CH: FASST-2.4GHz system (Multi-ch $UHDPRGHVHOHFWLRQ)UHTXHQF\UDQJH
mode/7ch mode)
The T8FG transmitter has been designed
6HOHFWWKH08/7,VHWWLQJIRUDOO)XWDED)$667 WR IXQFWLRQ LQ PDQ\ FRXQWULHV ,I \RX ZLOO EH
* 0XOWLFK PRGH UHFHLYHUV UHJDUGOHVV RI utilizing this transmitter in a country other than
QXPEHU RI FKDQQHOV HJ +65+6 )UDQFH SOHDVH PDNH VXUH WKDW >$5($@ LV VHW WR
5)65)6 &+ VHWWLQJ IRU DOO )XWDED *(1(5$/,IKRZHYHUWKLVWUDQVPLWWHUZLOOEH
)$667* FK PRGH UHFHLYHUV UHJDUGOHVV RI XWLOL]HGLQ)UDQFHLWPXVWEHVHWWR)5$1&(LQ
QXPEHU RI FKDQQHOV HJ 5))5))0 RUGHUWRFRPSO\ZLWK)UHQFKUHJXODWLRQV
5)65)6
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button.
)XQFWLRQVRI/LQNDJH0HQX! 55
Channel assignment of each function can be changed.
FUNCTION
:KHQ\RXVHOHFWPRGHODQGZLQJVZDVKW\SHV 9a9YLUWXDOFKDQQHOV
\RXZLOOILQGWKDWWKHRSWLPL]HGFRPELQDWLRQVRI These four channels can be set as virtual
servo output channels and functions have been functions that do not have servo output channels.
DOUHDG\SUHVHW,I\RXZRXOGOLNH\RXFDQIUHHO\ <RX FDQ IUHHO\ FKDQJH FRPELQDWLRQV EHWZHHQ
FKDQJH FRPELQDWLRQV RI VHUYR RXWSXW FKDQQHOV IXQFWLRQVDLOHURQHOHYDWRUHWFDQGLQSXWFRQWUROV
IXQFWLRQVDLOHURQHOHYDWRUHWFDQGFRQWUROVWLFNV VWLFNVVZLWFKHVDQGWULPOHYHUV
VZLWFKHVDQGWULPOHYHUV
*You can also assign the same function to multiple servo 6HUYR2XWSXW&KDQQHOV
output channels such as assigning elevator function to CH2 )RU)$6670XOWL&+PRGH\RXFDQVHWOLQHDU
and CH3. FKDQQHOVDQGWZRGLJLWDOFKDQQHOV)RU)$667&+
&KDQQHO5HSODFHPHQW PRGH\RXFDQVHWRQO\VHYHQOLQHDUFKDQQHOV
When the channel is replaced by using this
'*GLJLWDOFKDQQHOV
FKDQQHOUHSODFHPHQWIXQFWLRQWKHUHSODFHPHQWLV 7KHVHFKDQQHOVFDQIXQFWLRQDVVZLWFKHGFKDQQHOV<RXFDQ
IUHHO\FKDQJHFRPELQDWLRQVEHWZHHQVHUYRRXWSXWFKDQQHOV
DXWRPDWLFDOO\ GRQH DV IRU WKH VHWWLQJ GDWD $79 DQGLQSXWFRQWUROVVWLFNVVZLWFKHVDQGWULPOHYHUV
68%75,05(9(56()6DQG%)6HWFVHW
to those channels respectively.
7KHGLVSOD\VFUHHQLVDQH[DPSOH7KH
VFUHHQGHSHQGVRQWKHPRGHOW\SH
)XQFWLRQFKDQJH 2SHUDWLRQFRQWUROFKDQJH
1. Move the cursor to the function item of the 1. Move the cursor to the "CTRL" item of the
channel you want to change and touch the channel you want to change and touch the
RTN button. RTN button.
*The function selection screen is displayed. *The control selection screen is displayed.
2. Move the cursor to the function name you
want to set and touch the RTN button.
*The function name blinks.
3. Touch the RTN button to execute the
change. (When you want to cancel this
operation, touch the S1 button.) 2. Move the cursor to the control you want to
0XOWLSOHFKDQQHOVFDQEHDVVLJQHGWRRQHIXQFWLRQ change, and touch the RTN button.
*The same control can be assigned to multiple channels.
56 )XQFWLRQVRI/LQNDJH0HQX!
7ULPVHWWLQJ &KDQQHOUHSODFHPHQW
Move the cursor to the "TRIM" item of the Move the cursor to the channel # you want
channel you want to change and touch the to replace and touch the RTN button to
RTN button. switch to the data input mode.
*The trim setup screen is displayed. Select the destination channel # by scrolling
the touch sensor. A confirmation message
appears. Touch the RTN button to replace
the channel. (To terminate input and return
to the original state, touch the S1 button.)
7ULPVHOHFWLRQ
Move the cursor to the trim, lever, etc. you
want to set and touch the RTN button.
*The setting can be changed.
7ULPUDWHVHWWLQJ
Move the cursor to the [RATE] item and
touch the RTN button to switch to the data
input mode.
Set the trim rate by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHWULP
UDWHLVUHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end adjustment and
return to the cursor mode.
7ULPPRGHVHOHFWLRQ
Move the cursor to the [MODE] item and
touch the RTN button to switch to the data
input mode.
Select the trim mode by scrolling the touch
sensor. A confirmation message appears.
Touch the RTN button to change the mode.
(To terminate input and return to the original
state, touch the S1 button.)
)XQFWLRQVRI/LQNDJH0HQX! 57
Setting of neutral position of each servo.
SUB-TRIM
The Sub-Trim function is used to set the servo
QHXWUDO SRVLWLRQ DQG PD\ EH XVHG WR PDNH ILQH
DGMXVWPHQWV WR WKH FRQWURO VXUIDFH DIWHU OLQNDJHV
and pushrods are hooked up. When you begin to set
XSDPRGHOEHVXUHWKDWWKHGLJLWDOWULPVDUHVHWWR
their center position.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ$GMXVWLQJ YDOXH
RTN button.
7KHGLVSOD\VFUHHQLVDQH[DPSOH7KH
VFUHHQGHSHQGVRQWKHPRGHOW\SH
6XEWULPDGMXVWPHQW
1. Move the cursor to the channel you want to
adjust and touch the RTN button to switch to
the data input mode.
2. Adjust the rate by scrolling the touch sensor.
Initial value: 0
Adjustment range: -240~+240 (steps)
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGVXEWULPLV
UHVHWWRWKHLQLWLDOYDOXH
%HIRUHVXEWULPDGMXVWPHQWLWLVYHU\LPSRUWDQWWRDGMXVWWKH
linkages at the control surface so that you do not use sub-
WULPH[FHSWIRUYHU\PLQXWHDGMXVWPHQWV
3. Touch the RTN button to end adjustment and
return to the cursor mode.
4. Repeat this procedure for each channel.
58 )XQFWLRQVRI/LQNDJH0HQX!
Use to reverse the throw direction.
REVERSE
Servo Reverse changes the direction of an WRWHOOZKHWKHUWKHVHUYRQHHGVWREHUHYHUVHGRUD
LQGLYLGXDOVHUYR¶VUHVSRQVHWRDFRQWUROLQSXW setting in the function needs to be reversed. See the
)RU &&30 KHOLFRSWHUV EH VXUH WR UHDG WKH instructions for each specialized function for further
VHFWLRQRQ6ZDVK$)5EHIRUHUHYHUVLQJDQ\VHUYRV GHWDLOV$OZD\VFKHFNVHUYRGLUHFWLRQSULRUWRHYHU\
:LWK &&30 KHOLFRSWHUV DOZD\V FRPSOHWH \RXU ÀLJKWDVDQDGGLWLRQDOSUHFDXWLRQWRFRQ¿UPSURSHU
servo reversing prior to any other programming. PRGHOPHPRU\KRRNXSVDQGUDGLRIXQFWLRQ
If you use pre-built Airplane/Sailplane functions
WKDWFRQWUROPXOWLSOHVHUYRVLWPD\EHFRQIXVLQJ
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button.
7KHGLVSOD\VFUHHQLVDQH[DPSOH7KH
VFUHHQGHSHQGVRQWKHPRGHOW\SH
6HUYRUHYHUVLQJSURFHGXUH
8SRQVHWXSFRPSOHWLRQRIDQHZPRGHOFKHFNZKHWKHURU
not each servo is connected to the correct channel.
1H[WGHWHUPLQHZKHWKHU\RXQHHGWRUHYHUVHDQ\FKDQQHOV
by moving each stick and/or other control inputs.
1. Move the cursor to the channel you want to
reverse and touch the RTN button to switch
to the data input mode.
2. Select the direction by scrolling the touch
VHQVRU $ FRQÀUPDWLRQ PHVVDJH DSSHDUV
[NORM]: Normal
[REV]: Reverse
3. T o u c h t h e R T N b u t t o n t o c h a n g e t h e
direction. (To terminate input and return to
the original state, touch the S1 button.)
)XQFWLRQVRI/LQNDJH0HQX! 59
Sets the servos operating position when transmitter signals can no
FAIL SAFE longer be received or when the receiver battery voltage drops.
)DLOVDIHVHWWLQJSURFHGXUH %DWWHU\IDLOVDIHVHWWLQJSURFHGXUH
1. Move the cursor to the "F/S" item of the Battery fail safe can be set for each channel
channel you want to set and touch the RTN by the same method as the fail safe setting
button to switch to the data input mode. procedure. Select and set the "B.F/S" item.
2. Select the F/S mode by scrolling the touch [ON]: Battery fail safe function ON
VHQVRU $ FRQÀUPDWLRQ PHVVDJH DSSHDUV [OFF]: Battery fail safe function OFF
*The display blinks.
%DWWHU\IDLOVDIHUHOHDVHVZLWFKVHWWLQJ
3. Touch the RTN button. (Touch the S1 button
to stop setting.) This function temporarily releases the battery
7KHFKDQQHOVZLWFKHVWRWKH)6PRGH fail safe function for the fuselage to recover
after the battery fail safe function was
4. Move the cursor to the "POS" item. activated by a drop in the receiver battery
Hold the corresponding stick, knob, slider, voltage. This setting selects the switch which
etc. in the position you want the servo releases the battery fail safe function.
to move to when the fail safe function is 1. Move the cursor to the [RELEASE B.F/S] item in
activated and Touch the RTN button for one the setup screen (page 3).
second.
2. Touch the RTN button.
*The set position is displayed in percentage.
7KHVZLWFKVHOHFWLRQVFUHHQLVFDOOHG
,I\RXZDQWWRUHWXUQWKDWFKDQQHOWRWKHKROGPRGHPRYH
)RUDGHWDLOHGGHVFULSWLRQRIWKHVZLWFKVHOHFWLRQDQG21
the cursor to the "F/S" item and touch the RTN button
2))GLUHFWLRQVHWWLQJPHWKRGVHH>6ZLWFK6HWWLQJ0HWKRG@
WRVZLWFKWRWKHGDWDLQSXWPRGH6HOHFWWKH)6PRGHE\
at the back of this manual.
VFUROOLQJWKHWRXFKVHQVRU$FRQ¿UPDWLRQPHVVDJHDSSHDUV
and then change the mode by touching the RTN button.
60 )XQFWLRQVRI/LQNDJH0HQX!
Sets the travel and limit point of each servo.
(1'32,17
7KH(QG3RLQWIXQFWLRQDGMXVWVWKHOHIWDQGULJKW
VHUYR WKURZV JHQHUDWHV GLIIHUHQWLDO WKURZV DQG
ZLOOFRUUHFWLPSURSHUOLQNDJHVHWWLQJV
7KHWUDYHOUDWHFDQEHYDULHGIURPWR
LQHDFKGLUHFWLRQRQFKDQQHOVWR$OVRWKHOLPLW
SRLQWZKHUHVHUYRWKURZVWRSVPD\EHYDULHGIURP
WR
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ$GMXVWLQJ YDOXH
RTN button.
6HUYRWUDYHODGMXVWPHQW
1. Move the cursor to the travel item of the
channel you want to adjust and touch the
RTN button to switch to the data input mode.
2. Ajust the rate by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
reset to the initial value.
Touch the RTN button to end adjustment and
return to the cursor mode.
3. Repeat this procedure for each rate.
/LPLWSRLQWDGMXVWPHQW
1. Move the cursor to the limit point item of the
channel you want to adjust and touch the
RTN button to switch to the data input mode.
2. Ajust the limit point by scrolling the touch
sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHOLPLW
point is reset to the initial value.
Touch the RTN button to end adjustment and
return to the cursor mode.
3. Repeat this procedure for each limit point.
)XQFWLRQVRI/LQNDJH0HQX! 61
Stops the engine safely and easily.(airplane and helicopter only)
THR CUT
7KURWWOH FXW SURYLGHV DQ HDV\ ZD\ WR VWRS WKH
HQJLQH *HQHUDOO\ VSHDNLQJ PRGHOHUV ZLOO GR VR
E\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFNDWLGOH
The action is not functional at high throttle to
DYRLGDFFLGHQWDOGHDGVWLFNODQGLQJV7KHVZLWFK¶V
ORFDWLRQDQGGLUHFWLRQPXVWEHFKRVHQDVLWGHIDXOWV
WR18//
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
2. Switch selection:
Move the cursor to the [SW] item and access
the switch setup screen by touching the
RTN button and select the switch and ON
direction.
)RUDGHWDLOHGGHVFULSWLRQRIWKHVHWWLQJPHWKRGVHH>6ZLWFK
6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO
62 )XQFWLRQVRI/LQNDJH0HQX!
Lowers the engine idling speed.(airplane only)
IDLE DOWN
7KH ,GOH 'RZQ IXQFWLRQ ORZHUV WKH HQJLQH WR
LWVLGOHSRVLWLRQ/LNH7KURWWOH&XWWKLVLVXVXDOO\
DFFRPSOLVKHGE\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOH
stick at idle. The action is not functional at high
WKURWWOHWRDYRLGDFFLGHQWDOGHDGVWLFNV7KHVZLWFK¶
V ORFDWLRQ DQG GLUHFWLRQ PXVW EH FKRVHQ DV LW
GHIDXOWVWR18//
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
2. Switch selection:
Move the cursor to the [SW] item and access
the switch setup screen by touching the RTN
button. Select the switch and ON direction.
)RUDGHWDLOHGGHVFULSWLRQRIWKHVHWWLQJPHWKRGVHH>6ZLWFK
6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO
)XQFWLRQVRI/LQNDJH0HQX! 63
/LPLWV WKH VZDVK SODWH WUDYHO WR ZLWKLQ D À[HG UDQJH +HOLFRSWHU RQO\
SWASH RING
7KLVIXQFWLRQOLPLWVWKHVZDVKWUDYHOWRDIL[HG
UDQJH LQ RUGHU WR SUHYHQW GDPDJLQJ WKH VZDVK
linkage by simultaneous operation of the ailerons
and elevators. It is very useful in 3D aerobatics
ZKLFKXVHDODUJHWUDYHO
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
6ZDVKULQJVHWWLQJSURFHGXUH
1. Activate the function:
Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode.
Select the ACT mode by scrolling the touch
sensor.
*The display blinks.
Touch the RTN button to activate the
function and return to the cursor mode.
2. Rate setting:
Move the cursor to the [RATE] item touch the
RTN button to switch to the data input mode.
Set the rate by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH WR
$GMXVWWKHUDWHWRPD[LPXPVZDVKWLOW
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
reset to the initial value.
Touch the RTN button to end adjustment and
return to the cursor mode.
64 )XQFWLRQVRI/LQNDJH0HQX!
Swash AFR and linkage correction function. (helicopter only, except
SWASH swash type H-1)
1HXWUDO3RLQW 0L[LQJ5DWH
$W\RXUOLQNDJHVLIWKHVHUYRKRUQGHYLDWHVIURP 7KLVPL[LQJ LVXVHGWRFRPSHQVDWHWKHVZDVK
D SHUSHQGLFXODU SRVLWLRQ DW QHXWUDO WKH OLQNDJH plate as necessary during specific control inputs.
compensation functions in this menu may not 7KH IROORZLQJ FRPSHQVDWLRQ PL[LQJ LV SRVVLEOH
compensate effectively. To correct this use the 3,7WR$,/3,7WR(/($,/WR3,7(/(WR$,/
1HXWUDO3RLQWIXQFWLRQ7KLVZLOOPRYHWKHQHXWUDO DQG(/(WR3,7+5PRGH,WDGMXVWVWKHVZDVK
point of the servos to the actual perpendicular plate to for proper operation of each control using
SRVLWLRQ +RZHYHU WKLV DGMXVWPHQW FKDQJHV RQO\ the corresponding compensation mixing.
the axis point of the compensation functions in this
/LQNDJH&RPSHQVDWLRQ
PHQXDQGGRHVQRWDIIHFWWKHQHXWUDOSRVLWLRQRI
other functions. This compensation mixing is used to correct the
VZDVKSODWHIRUSLWFKFRQWURODWORZSLWFKDQGKLJK
6ZDVK$)5 pitch.
6ZDVK$)5 IXQFWLRQ UHGXFHV LQFUHDVHV RU
6SHHG&RPSHQVDWLRQ
UHYHUVHVWKHUDWHWUDYHORIWKHDLOHURQHOHYDWRUDQG
FROOHFWLYHSLWFKIXQFWLRQVE\DGMXVWLQJRUUHYHUVLQJ This function is used to cancel the reaction that
WKHPRWLRQRIDOOVHUYRVLQYROYHGLQWKDWIXQFWLRQ is generated by the difference in the movements of
RQO\ZKHQXVLQJWKDWIXQFWLRQ HDFKVHUYRZKHQWKHVZDVKSODWHPRYHV
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
1HXWUDOSRLQWVHWWLQJSURFHGXUH 6ZDVK$)5VHWWLQJSURFHGXUH
The neutral point becomes the correction 7KHVZDVK$)5IXQFWLRQPDNHVDGMXVWPHQWVVR
standard point. WKDWWKHVHUYRVWUDYHOWKHVSHFL¿HGDPRXQWE\>$,/@
$GMXVWLQJWKHVHUYRKRUQVRWKDWWKHQHXWUDOSRLQWLVQHDUWKH >(/(@DQG>3,7@RSHUDWLRQ
50% position makes the mixing amount small. 1. Move the cursor to the function you want to
1. Neutral point setting adjust and touch the RTN button to switch to
Move the cursor to the [POS] item and hold the data input mode.
the pitch operation so that the servo horn is 2. Adjust the AFR rate by scrolling the touch
at a right angle to the linkage rod and Touch sensor.
the RTN button for one second. This value ,QLWLDO YDOXH
indicates the servo's neutral position.
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKH$)5
After reading the neutral point, use the rate is reset to the initial value.
other correction functions to make further
Touch the RTN button to end adjustment and
adjustments.
return to the cursor mode.
)XQFWLRQVRI/LQNDJH0HQX! 65
0L[LQJUDWHVHWWLQJSURFHGXUH
7KH +5 VZDVKSODWH W\SH ZLOO EH XVHG DV DQ
example to describe mixing rate setting. The mixing
XVHG LQ RWKHU VZDVK PRGHV PD\ EH GLIIHUHQW
KRZHYHUWKHVHWWLQJSURFHGXUHLVWKHVDPH
:KHQPDNLQJWKHIROORZLQJVHWWLQJ0RYHWKHFXUVRUWRWKH
LWHP\RXZDQWWRVHWDQGWRXFKWKH571EXWWRQWRVZLWFK
to the data input mode. Touch the RTN button to end
DGMXVWPHQWDQGUHWXUQWRWKHFXUVRUPRGH
/LQNDJHFRPSHQVDWLRQVHWWLQJSURFHGXUH
3ULRU WR XWLOL]LQJ WKH OLQNDJH FRPSHQVDWLRQ VHWWLQJV LW LV
LPSRUWDQWWRDGMXVWWKHPL[LQJUDWHVHWWLQJV
/LQNDJH FRPSHQVDWLRQ RYHUULGHV LQWHUIHUHQFH IURP WKH
DLOHURQ RSHUDWLRQ ZLWK WKH HOHYDWRU RU HOHYDWRU RSHUDWLRQ
ZLWKWKHDLOHURQDWFROOHFWLYHSLWFKFRQWUROIRUORZSLWFKDQG
high pitch.
66 )XQFWLRQVRI/LQNDJH0HQX!
Digital trim settings
T1-T4 SET.
7KLV IXQFWLRQ DGMXVWV WKH GLJLWDO WULP
V VWHS 2QO\WKHWULPGLVSOD\HGRQWKHKRPHVFUHHQFDQ
DPRXQWDQGRSHUDWLRQPRGH7a7 EHPRYHGWRWKHFHQWHUSRVLWLRQZLWKRXWFKDQJLQJ
:KHQ WKH IOLJKW FRQGLWLRQV DUH VHW WKH WULP the actual trim's memory position.
RSHUDWLRQFDQEHFRXSOHGZLWKWKHFRQGLWLRQVZKHQ
combination mode is selected.
The T8FG's unit of trim is displayed on the home
screen.
ŏ 6HOHFW >77 6(7@ LQ WKH /LQNDJH PHQX DQG DFFHVV ŏ 7ULP RSHUDWLRQ PRGH
the setup screen shown below by touching the "COMB.": Combination mode
RTN button.
"SEPAR": Separate mode
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
)XQFWLRQVRI/LQNDJH0HQX! 67
Model memory setting data reset.
DATA RESET
7KLVIXQFWLRQLVGHVLJQHGWRDOORZ\RXWRUHVHW $OOPRGHOVHWWLQJ
trim settings or all of the settings saved in the active 5HVHWVDOO/LQNDJHDQG0RGHO0HQXIXQFWLRQV
model memory. You may individually choose to H[FHSW IRU )UHTXHQF\ 0RGHO 6HOHFW DQG 0RGHO
UHVHWWKHIROORZLQJGDWD Type.
T1~T4:
Reset the digital trim setting.
*The trim step amount and trim rate are not reset.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Linkage ŏ0RYLQJ FXUVRU
menu by touching the
RTN button.
'DWDUHVHWWLQJPHWKRG
1. Move the cursor to the item you want to
reset and touch the RTN button.
$FRQ¿UPDWLRQPHVVDJHDSSHDUV
2. Execute reset by touching the RTN button for
one second. (Touch the S1 button to cease
resetting.)
68 )XQFWLRQVRI/LQNDJH0HQX!
02'(/0(18&20021)81&7,216
7KLVVHFWLRQGHVFULEHVWKH'5SURJUDPPL[LQJ Note: The T8FG is designed so that the airplane
and other functions common to all model types. and glider (including EP glider) model types
are compatible with aircraft of similar type
%HIRUH VHWWLQJ WKH PRGHO GDWD XVH WKH 0RGHO wings.
7\SH IXQFWLRQ RI WKH /LQNDJH PHQX WR VHOHFW WKH This section outlines the relationship between
model type matched to the aircraft. If a different the functions common to airplanes and
PRGHOW\SHLVVHOHFWHGDIWHUZDUGVWKH'5SURJUDP gliders, except some dedicated functions,
PL[LQJDQGRWKHUSDUDPHWHUVDUHUHVHW and model type.
The setting menus will depend on the number
If either a helicopter or glider have been selected
of servos and other differences according to
DVWKHPRGHOW\SHWKHQWKHVSHFL¿FIXQFWLRQVLQWKH the wing type used. The setup screens in the
0RGHOPHQXFDQEHVHWIRUHDFKÀLJKWFRQGLWLRQ,I instruction manual are typical examples.
\RXZDQWWRVZLWFKWKHVHWWLQJVIRUHDFKFRQGLWLRQ
E\ VZLWFK VWLFN SRVLWLRQ HWF XVH WKH &RQGLWLRQ
6HOHFWIXQFWLRQWRDGGÀLJKWFRQGLWLRQV8SWR¿YH
FRQGLWLRQVFDQEHXVHG
<SensorTouch™>
ŏ6HOHFW >02'(/ 0(18@ Scrolling
and return to the home ŏ0RYLQJ FXUVRU
screen by touching the
RTN button.
7KH0RGHOPHQXVFUHHQGHSHQGVRQWKH
model type.
ŏ 6HOHFW WKH IXQFWLRQ \RX ZDQW WR VHW DQG
access the setup screen by touching the RTN
button.
Ɣ6(592 LQIRUPDWLRQ RQ KRZ WR GR VR SOHDVH UHIHU WR WKH
6HUYR WHVW DQG VHUYR SRVLWLRQ GLVSOD\ )RU D 6ZLWFK6HWWLQJ0HWKRGORFDWHGDWWKHEDFNRIWKLV
GHVFULSWLRQRILWVIXQFWLRQVVHHWKH/LQNDJH0HQX manual.
VHFWLRQ Ɣ352*0,;
Ɣ&21',7,21DSSOLFDEOHWRKHOLFRSWHUDQG 7KH 7)* WUDQVPLWWHU DOORZV XS WR ILYH
JOLGHUVHOHFWLRQV completely customizable program mixes.
)OLJKW FRQGLWLRQV DGGLWLRQ GHOHWLRQ FRS\
FRQGLWLRQUHQDPLQJDQGFRQGLWLRQGHOD\FDQEHVHW
Ɣ'8$/5$7(
The D/R curve of a T8FG transmitter may be
DFWLYDWHG IURP D VZLWFK VWLFN SRVLWLRQ HWF )RU
0RGHO0HQX&RPPRQ)XQFWLRQV! 69
Flight condition's switch assignment, copy, priority change and
CONDITION condition delay can be set. [except airplane type]
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
&RQGLWLRQQDPH &RQGLWLRQVZLWFK
3ULRULW\FKDQJH
1. Move the cursor to the priority up-arrow or
6HWXSVFUHHQSDJH down-arrow you want to change and touch
the RTN button.
1. Move the cursor to the [SOURCE] item and
touch the RTN button to switch to the data The priority of the corresponding condition is
input mode. changed. (The last condition becomes the
highest priority.)
Select the copy source condition by scrolling
the touch sensor. Then, touch the RTN button. *The normal condition cannot be shifted. The priority is the
ORZHVW
2. Move the cursor to the [DESTIN.] item and
touch the RTN button.
70 0RGHO0HQX&RPPRQ)XQFWLRQV!
&RQGLWLRQGHOD\VHWWLQJ
6HWXSVFUHHQSDJH
1. Select the condition for which you want to
set.
2. Move the cursor to the "DELAY" item of the
channel you want to set and touch the RTN
button to switch to the data input mode.
Adjust the delay amount by scrolling the
touch sensor.
Initial value: 0
Adjustment range: 0~27 (maximum delay)
3. Touch the RTN button to end adjustment and
return to the cursor mode.
0RGHO0HQX&RPPRQ)XQFWLRQV! 71
The angle and curve of each stick function can be set. [All model types]
DUAL RATE
'XDOUDWHIXQFWLRQLVXVHGWRDGMXVWWKHDPRXQW This is normally used after the End Point
RI WKURZ DQG WKH RSHUDWLRQDO FXUYH RI WKH VWLFN programming has been completed to define the
IXQFWLRQV DLOHURQ HOHYDWRU DQG UXGGHU IRU HDFK PD[LPXPWKURZ:KHQPL[LQJLVDSSOLHGIURPRQH
ÀLJKWFRQGLWLRQRUXSWRUDWHVIRUHDFKIXQFWLRQ FKDQQHOWRDQRWKHUFKDQQHOERWKFKDQQHOVFDQEH
)RUDLUSODQHW\SHLWLVDOVRSRVVLEOHWRDGMXVWWKH DGMXVWHGDWWKHVDPHWLPHE\DGMXVWLQJWKHRSHUDWLRQ
operational curve of the throttle function. rate through the dual rate function.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ)XQFWLRQ VHOHFWLRQ
ŏ7R QH[W SDJH
&XUUHQWO\VHOHFWHGFLUFXLW
ŏ6ZLWFK VHOHFWLRQ
8SWR¿YHUDWHVIRUHDFKIXQFWLRQ
[Helicopter/glider]
ŏ6ZLWFK VHOHFWLRQ
72 0RGHO0HQX&RPPRQ)XQFWLRQV!
'XDOUDWHVHWWLQJSURFHGXUH
1. Function selection
Move the cursor to the function selection
item and touch the RTN button to switch to
the data input mode.
Select the function you want to adjust by
scrolling the touch sensor.
Touch the RTN button to the cursor mode.
2. Switch selection
Move the cursor to the circuit # item and
access the switch setup screen by touching
the RTN button. Select the switch activation
method and the activation position (if
applicable).
)RUDGHWDLOHGGHVFULSWLRQRIWKHVHWWLQJPHWKRGVHH>6ZLWFK
6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO
3. Left/right (up/down) rate adjustment
3HUIRUPWKHVHWWLQJVEHORZDIWHUFKDQJLQJWRWKHFLUFXLWRU
FRQGLWLRQ\RXZDQWWRDGMXVW
Move the cursor to the rate item you want to
adjust and touch the RTN button to switch to
the data input mode.
Adjust the rate by scrolling the touch sensor.
,QLWLDOYDOXH
$GMXVWPHQWUDQJHa
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR
RSHUDWLRQSRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
Repeat this procedure for additional rate
and other functions as desired.
4. Operation curve (EXP curve) adjustment
3HUIRUPWKHVHWWLQJVEHORZDIWHUFKDQJLQJWRWKHFLUFXLWRU
FRQGLWLRQ\RXZDQWWRDGMXVW
Move the cursor to the EXP item you want to
adjust and touch the RTN button to switch to
the data input mode.
Adjust the rate by scrolling the touch sensor.
,QLWLDOYDOXH
$GMXVWPHQWUDQJHa
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR
RSHUDWLRQSRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
8VLQJWKH(;3FXUYHLVHIIHFWLYHWRVPRRWKHRUVRIWHQWKH
control inputs around center to avoid over-controlling the
PRGHO7KLV LV RIWHQ XVHG IRU WKH DLOHURQV HOHYDWRU DQG
UXGGHUDQGPD\EHXVHGZLWKWKHWKURWWOHLQWKHFDVHRIDQ
DLUSODQHVHOHFWLRQWRVPRRWKHWKHHQJLQHFRQWUROVDVZHOO
Touch the RTN button to end adjustment and
return to the cursor mode.
Repeat this procedure for all other rates and
functions as desired.
0RGHO0HQX&RPPRQ)XQFWLRQV! 73
Program mixing which can be freely customized. Up to five mixings
352*0,; can be used for each model. [All model types]
ŏ0L[
0L[VHWXSVFUHHQFDOO
ŏ 0RYH WKH FXUVRU WR WKH PL[ ZKRVH IXQFWLRQ \RX ZDQW WR DFWLYDWH
and access the setup screen by touching the RTN button.
ŏ0L[LQJ UDWH /HIWULJKW XSGRZQ
[Linear curve] [5-point curve]
ŏ&XUYH VHOHFWLRQ ŏ2IIVHW UDWH; < ŏ&XUYH VHOHFWLRQ ŏ3RLQW UDWH SRLQW
74 0RGHO0HQX&RPPRQ)XQFWLRQV!
Ɣ212))VZLWFKVHWWLQJ Ɣ7ULPPRGH212))VHWWLQJ
Move the cursor to the switch item and 1. When changing the trim mode, move the
access the switch setup screen by touching cursor to the [TRIM] item and touch the RTN
the RTN button and select the switch and ON button to switch to the data input mode.
direction. Select ON/OFF by scrolling the touch sensor.
)RUDGHWDLOHGGHVFULSWLRQRIWKHVHWWLQJPHWKRGVHH>6ZLWFK *The display blinks.
6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO
Touch the RTN button to change the trim
$OZD\VRQZKHQ>@ mode ON/OFF and return to the cursor
Ɣ0DVWHUFKDQQHOVHWWLQJ mode.
7RLQFRUSRUDWHWKHPL[LQJIURPWKHPDVWHUWULPVHOHFW>21@
1. Move the cursor to the [MASTER] item and ,IWULPLVQRWGHVLUHGVHOHFW>2))@
touch the RTN button to switch to the data
(IIHFWLYHZKHQDIXQFWLRQLVVHWLQWKHPDVWHUFKDQQHO
input mode.
Select the function by scrolling the touch Ɣ/LQHDUFXUYHVHWWLQJ
sensor.
[Rate setting]
*The display blinks.
1. Move the cursor to the mixing rate setting
Touch the RTN button to change the function item and touch the RTN button to switch to
and return to the cursor mode. the data input mode.
2. When you want to link this mixing with other Adjust the rate by scrolling the touch sensor.
mixes, move the cursor to the [LINK] item and
touch the RTN button to switch to the data ,QLWLDOYDOXH
input mode. $GMXVWPHQWUDQJHa
Select the link mode, either [+] or [-], by
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR
scrolling the touch sensor. operation position is reset to the initial value.
*The display blinks. Touch the RTN button to end adjustment and
Touch the RTN button to set the link mode return to the cursor mode.
and return to the cursor mode. 2. Repeat this procedure for all other rates as
*Check to ensure that the link mode is functioning properly desired.
by operating the mix accordingly. [Offsetting the curve horizontally in the vertical
0DVWHUFKDQQHOFRQWUROFDQEHVHWWRDFWLYDWHEDVHGRQWKH or horizontal direction]
DPRXQWRIVWLFNLQSXWRU95LQSXWQHLWKHURIZKLFKLQFOXGH 1. Move the cursor to the [OFFS] setting item
$79 '5 DQG PL[LQJ VHOHFWLRQ ,Q WKLV FDVH WKH VZLWFK and touch the RTN button to switch to the
VHWXSVFUHHQLVGLVSOD\HGE\WRXFKLQJWKH571EXWWRQZLWK data input mode.
"H/W" selected in the function selection. Select master Adjust the offset rate by scrolling the touch
FKDQQHOFRQWURO7RWHUPLQDWHWKH+:VHOHFWLRQVHOHFW sensor.
the [--] display and touch the RTN button.
,QLWLDOYDOXH
Ɣ6ODYHFKDQQHOVHWWLQJ $GMXVWPHQWUDQJHa
1. Move the cursor to the [SLAVE] item and
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR
touch the RTN button to switch to the data RSHUDWLRQSRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
input mode. Touch the RTN button to end the adjustment
Select the function by scrolling the touch and return to the cursor mode.
sensor. 2. Repeat this procedure for the other direction.
*The display blinks.
ƔSRLQWFXUYHVHWWLQJ
Touch the RTN button to change the function
and return to the cursor mode. [Rate setting]
2. When you want to link this mixing with other 1. Move the cursor to the point rate setting item
mixes, move the cursor to the [LINK] item and you want to adjust and touch the RTN button
touch the RTN button to switch to the data to switch to the data input mode.
input mode. Adjust the rate by scrolling the touch sensor.
Select the link mode to [+] or [-] by scrolling ,QLWLDOYDOXH
the touch sensor. $GMXVWPHQWUDQJHa
*The display blinks.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR
Touch the RTN button to set the link mode RSHUDWLRQSRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
and return to the cursor mode. Touch the RTN button to end the adjustment
*Check the direction by actual operation. and return to the cursor mode.
2. Repeat this procedure for each point as
desired.
0RGHO0HQX&RPPRQ)XQFWLRQV! 75
Dedicated mixing used to adjust the fuel mixture of applicable
)8(/0,; engines. [Airplane/helicopter]
[Airplane type]
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ$FFHOHUDWLRQ VHWWLQJ
[Helicopter type]
76 0RGHO0HQX&RPPRQ)XQFWLRQV!
6HWWLQJPHWKRG Touch the RTN button to end adjustment and
return to the cursor mode.
%HIRUHXVLQJWKLVIXQFWLRQDVVLJQWKH>)8(/0,;@IXQFWLRQ
1HHGOHKLJKWULPZRUNVDVKLJKWULPEDVHGRQWKHFHQWHU
WRDQXQXVHGFKDQQHOLQWKH/LQNDJHPHQX>)81&7,21@
:RUNVOLNH$7/WULP
function.
Ɣ$FFHOHUDWLRQVHWWLQJ$LUSODQH
Ɣ$FWLYDWHWKHIXQFWLRQ
7KLV IXQFWLRQ LV XVHG WR DGMXVW WKH QHHGOHHQJLQH ULVH
1. Move the cursor to the [ACT] item and touch characteristics during acceleration. This enables an
the RTN button to switch to the data input DFFHOHUDWLRQIXQFWLRQZKLFKWHPSRUDULO\LQFUHDVHVWKHQHHGOH
mode. operation from the throttle stick.
Select the ACT mode by scrolling the touch 7KLV IXQFWLRQ LV XVHG ZKHQ WKHUH DUH V\PSWRPV RI WKH
sensor. PL[WXUH EHLQJ WRR OHDQ RU WRR ULFK ZKLFK ZRXOG EH
*The display blinks. generated by sudden throttle stick inputs.
Touch the RTN button to activate the [Acceleration rate setting (RATE)]
function and return to the cursor mode. (ON
$FFHOHUDWLRQ FDQ EH DGMXVWHG IRU DW ERWK KLJK DQG ORZ
is displayed.)
settings.
2. Move the cursor to the [MIX] item and touch
the RTN button to switch to the data input [Damping rate setting (DUMPING)]
mode.
7KHUHWXUQWLPHDIWHURSHUDWLRQ'XPSLQJFDQEHVHW
Select the mixing mode you want to change Move the cursor to the rate item you want to
by scrolling the touch sensor. change and touch the RTN button to switch
*The display blinks. to the data input mode.
Touch the RTN button to change the mode Adjust the rate by scrolling the touch sensor.
and return to the cursor mode.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
:KHQ>0,;@LVVHOHFWHGDWWKH>0,;@LWHPWKHWKURWWOHFXUYH UHVHWWRWKHLQLWLDOYDOXH
setting data becomes the mixing master side data. When Touch the RTN button to end adjustment and
>810,;@LVVHOHFWHGWKHWKURWWOHVWLFNSRVLWLRQEHFRPHVWKH return to the cursor mode.
mixing master.
[Operation point setting (ACT POS)]
ƔSRLQWFXUYHVHWWLQJ
7KHRSHUDWLRQSRLQWDWZKLFKWKHDFFHOHUDWLRQVHWWLQJZLOO
RFFXU,IWKLVSRLQWLVH[FHHGHGDFFHOHUDWLRQLVSHUIRUPHG
1. Move the cursor to the point rate setting item
you want to adjust and touch the RTN button Move the cursor to the [ACT POS] item and
to switch to the data input mode. hold the throttle stick to the position you
Adjust the rate by scrolling the touch sensor. want to change and touch the RTN button
for one second.
,QLWLDOYDOXH
Note: When using the acceleration funtion,
$GMXVWPHQWUDQJHa since the needle stroke is large, adjust your
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR settings so there is no binding of your linkage.
RSHUDWLRQSRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
Ɣ(QJLQHFXWVHWWLQJ
Touch the RTN button to end adjustment and
return to the cursor mode.
2SHUDWLRQOLQNHGZLWKWKHWKURWWOHKROGIXQFWLRQWKURWWOHFXW
IXQFWLRQDQGLGOHGRZQIXQFWLRQLVSRVVLEOH7KHWKURWWOHFXW
2. Repeat this procedure for each point.
SRVLWLRQFDQEHDGMXVWHGDFFRUGLQJO\6HWLWWRWKHIXOOFORVHG
Ɣ1HHGOHKLJKWULPVHWWLQJ position.
1. Move the cursor to the needle high trim Move the cursor to the throttle cut or idle
selection item and access the switch setup down item and touch the RTN button to
screen by touching the RTN button. Select switch to the data input mode.
the needle high trim lever. Adjust the servo position by scrolling the
)RUDGHWDLOHGGHVFULSWLRQRIWKHVHWWLQJPHWKRGVHH>6ZLWFK touch sensor.
6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO ,QLWLDOYDOXH7+5&87,'/('2:1
2. Move the cursor to the TRIM rate item and $GMXVWPHQW UDQJH 7+5 &87 a ,'/(
touch the RTN button to switch to the data '2:1a
input mode.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
Adjust the trim rate by scrolling the touch UHVHWWRWKHLQLWLDOYDOXH
sensor. Touch the RTN button to end the adjustment
,QLWLDOYDOXH and return to the cursor mode.
$GMXVWPHQWUDQJHa
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
0RGHO0HQX&RPPRQ)XQFWLRQV! 77
02'(/0(18$,53/$1(*/,'(5)81&7,216
7KH GHGLFDWHG PL[HV HWF WKDW DUH DSSOLFDEOH SRVLWLRQXVHWKH&RQGLWLRQ6HOHFWIXQFWLRQWRDGG
ZKHQDQDLUSODQHRUJOLGHUPRGHOW\SHLVVHOHFWHG IOLJKWFRQGLWLRQV8SWRILYHFRQGLWLRQVFDQEH
DUH GLVSOD\HG LQ WKLV 0RGHO PHQX IXQFWLRQV XVHG
VHFWLRQ3ULRUWRDGMXVWLQJDQ\RIWKHVHPL[HVHWF Note: The T8FG is designed so that the airplane and
XVHWKH0RGHO7\SHIXQFWLRQLQWKH/LQNDJHPHQX glider model types can utilize aircraft of the same
WRVHOHFWWKHPRGHOW\SHZLQJW\SHDQGWDLOW\SH wing type.
PDWFKHGWRWKHDLUFUDIW2WKHUVHWWLQJVUHVHWWKH The functions common to airplanes and gliders, with
GDWDXVHGLQPL[LQJIXQFWLRQHWF the exception of some dedicated functions, are
written without regard to the model type.
)RU JOLGHU PDQ\ GHGLFDWHG PL[HV FDQ EH VHW While there may be differences, depending on the
IRUHDFKIOLJKWFRQGLWLRQDVUHTXLUHG7RVZLWFK number of servos, etc. the wing type used, etc. the
WKHVHWWLQJVIRUHDFKFRQGLWLRQE\VZLWFKRUVWLFN setup screens in the instruction manual are typical
examples.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the
RTN button.
78 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
AIL to RUD AIRBRAKE
7KLVPL[LVXVHGZKHQ\RXZDQWWRFRRUGLQDWH 7KLV IXQFWLRQ LV XVHG ZKHQ DLUEUDNHV DUH
WKHUXGGHUZLWKDLOHURQRSHUDWLRQIRUEDQNLQJDW QHFHVVDU\ZKHQODQGLQJRUZKHQGLYLQJHWFGXULQJ
VKDOORZDQJOHV>$LUSODQHJOLGHUJHQHUDO@ ÀLJKW$LUSODQHDLOHURQVRUPRUH
RUD to AIL GYRO
7KLV IXQFWLRQ LV XVHG ZKHQ \RX ZDQW WR PL[ 7KLVLVDGHGLFDWHGPL[ZKHQD*<$6HULHVJ\UR
WKHDLOHURQVZLWKUXGGHULQSXW5XGGHULVDSSOLHG LVXVHG>$LUSODQHJOLGHUJHQHUDO@
GXULQJUROOLQJPDQHXYHUVVXFKDVNQLIHHGJHÀLJKW
V-TAIL
>$LUSODQHJOLGHUJHQHUDO@
This function incorporates the elevators and
&$0%(50,; UXGGHULQSXWIRUXVHZLWK9WDLOPRGHOV>$LUSODQH
7KLV PL[ DGMXVWV WKH FDPEHU DQG FRUUHFWV WKH JOLGHU9WDLOVSHFL¿FDWLRQV@
HOHYDWRUV>$LUSODQHJOLGHUDLOHURQVRUPRUH@ $,/(9$725'8$/(/(9$725
ELE to CAMBER 7KLVIXQFWLRQDGMXVWVWKHHOHYDWRUVDQGDLOHURQV
7KLV PL[ LV XVHG ZKHQ \RX ZDQW WR WKH PL[ RIPRGHOVZLWKHOHYDWRUVSHFLILFDWLRQV>$LUSODQH
FDPEHUÀDSVZLWKHOHYDWRUWRLQFUHDVHWKHOLIWRIWKH JOLGHUDLOHYDWRUVSHFL¿FDWLRQV@
PRGHO>$LUSODQHJOLGHUDLOHURQVRUPRUH@ WINGLET
&$0%)/3WR(/( 7KLVIXQFWLRQDGMXVWVWKHOHIWDQGULJKWUXGGHUV
This mix is used to correct for changes in attitude RI ZLQJOHW PRGHOV >$LUSODQHJOLGHU ZLQJOHW
ZKHQ WKH FDPEHU IODSV DUH XWLOL]HG >$LUSODQH VSHFL¿FDWLRQV@
JOLGHUDLOHURQVÀDSRUPRUH@ MOTOR
%877(5)/<&URZ 7KLVIXQFWLRQDGMXVWVWKHRSHUDWLRQVSHHGZKHQ
7KLVIXQFWLRQLVXVHGWRTXLFNO\VORZWKHDLUFUDIW the motor of an F5B or other such EP glider is
DQGRU UHGXFH WKH DOWLWXGH >*OLGHU DLOHURQV RU VWDUWHGE\DVZLWFK>$LUSODQHJOLGHUJHQHUDO@
PRUH)O\LQJDLOHURQVÀDSRUPRUH@ RUD to ELE
75,00,; This function is used to correct rolling maneuvers
7KHDLOHURQVHOHYDWRUVDQGÀDSVWULPRIIVHWUDWH VXFKDVNQLIHHGJHÀLJKW>$LUSODQHJHQHUDO@
FDQEHDFFHVVHGE\VHOHFWLQJDVZLWFKRUFRQGLWLRQ 61$352//
VHOHFWLRQDVGHVLUHG>*OLGHUDLOHURQVRUPRUH@
7KLV IXQFWLRQ VHOHFWV WKH VQDS UROO VZLWFK DQG
DGMXVWVWKHDPRXQWRIVHUYRLQSXW6HUYRVSHHGFDQ
DOVREHDGMXVWHG>$LUSODQHJHQHUDO@
V-TAIL AILVATOR
ELEVATOR
(RUDDER 2)
RUDDER ELEVATOR ELEVATOR 2
(ELEVATOR 2) (AILERON 5) (AILERON 6)
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 79
[Corresponding model type]: Airplane, general
THR CURVE
7KLV IXQFWLRQ DGMXVWV WKH WKURWWOH FXUYH IRU NOTE: If this throttle curve function is activated,
optimum engine speed from throttle stick input. you can not use the THR-EXP function within
the DUAL RATE function simultaneously.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
80 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
[Corresponding model type]: Airplane, general
THR DELAY
7+5'(/$< IXQFWLRQ LV XVHG WR VORZ WKH
UHVSRQVHRIWKHWKURWWOHVWLFNWRVLPXODWHWKHVORZ
UHVSRQVHRIDWXUELQHHQJLQHHWF
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
6HWWLQJPHWKRG
Ɣ2SHUDWLRQVSHHGGHOD\VHWWLQJ
1. Move the cursor to the [DELAY] item and
touch the RTN button to switch to the data
input mode.
Adjust the delay rate by scrolling the touch
sensor.
Initial value: 0
Adjustment range: 0~27 (maximum delay)
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to activate the
function and return to the cursor mode.
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 81
[Corresponding model type]: Airplane/glider, 2 ailerons or more
AIL DIFF.
The left and right aileron differential can be
DGMXVWHGLQGHSHQGHQWO\
)RUJOLGHUWKHGLIIHUHQWLDOUDWHLQEXWWHUÀ\PL[LQJ
FDQEHDGMXVWHG
AIL1 AIL 2
(Main Aileron) (Main Aileron)
ŏ 6HOHFW >$,/ ',))@ DW WKH 0RGHO PHQX
AIL 3 AIL 4
and access the setup screen shown (Chip Aileron) (Chip Aileron)
below by touching the RTN button.
*The display screen is an example. The actual
[Airplane (2A+2F)] VFUHHQGHSHQGVRQWKH0RGHO7\SH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
[Glider (4A+2F)]
Ɣ$LOHURQGLIIHUHQWLDODGMXVWPHQWLQEXWWHUÀ\
PL[LQJ
Move the cursor to the [BUTTERFLY ADJUST]
item and touch the RTN button to switch to
the data input mode.
82 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
>&RUUHVSRQGLQJ PRGHO W\SH@ $LUSODQHJOLGHU ÁDSV RU PRUH
)/$36(7
7KHXSGRZQWUDYHORIHDFKÀDSFDPEHUÀDSV
)/3 EUDNH IODSV )/3 FDQ EH DGMXVWHG
independently for each servo according to the
ZLQJW\SH
ŏ 7KH RSHUDWLRQ UHIHUHQFH SRLQW RI HDFK ÁDS FDQ EH
offset
The camber flaps of a 4-flap model can FLP 3 FLP 4
(Brake Flap) (Brake Flap)
EH PL[HG ZLWK WKH EUDNH IODSV %5.)/3 WR
FLP 1 FLP 2
&0%)/3 (Camber Flap) (Camber Flap)
ŏ $Q 212)) VZLWFK FDQ EH VHW
ŏ 6HOHFW >)/$3 6(7@ DW WKH 0RGHO PHQX DQG *The display screen is an example. The actual
access the setup screen shown below screen depends on the model type.
by touching the RTN button.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ 8 S ' R Z Q
adjustment
ŏ 2 S H U D W L R Q ŏ7R QH[W SDJH
reference point
offset *OLGHU&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
6HWWLQJPHWKRG
:KHQ WKH 571 EXWWRQ LV WRXFKHG IRU RQH VHFRQG WKH
UHIHUHQFHSRLQWLVUHVHWWRWKHLQLWLDOYDOXH
Ɣ)ODSXSGRZQDGMXVWPHQW Touch the RTN button to end the adjustment
Move the cursor to the flap (FLP) 1~4 Up or and return to the cursor mode.
Down item according to the wing type and
Ɣ$FWLYDWHWKH%UDNH)/3WR&DPEHU)/3PL[LQJ
touch the RTN button to switch to the data
input mode. Adjust the travel independently Move the cursor to the [ACT] item and touch
by scrolling the touch sensor. the RTN button to switch to the data input
,QLWLDO YDOXH mode. Select the ACT mode by scrolling the
touch sensor.
$GMXVWPHQW UDQJH a
*The display blinks.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH Touch the RTN button to activate the
function and return to the cursor mode. (ON
Touch the RTN button to end the adjustment is displayed.)
and return to the cursor mode.
To select a switch, move the cursor to the
Ɣ5HIHUHQFHSRLQWDGMXVWPHQW [SW] item and touch the RTN button to call
the selection screen. Select the switch and
Move the cursor to the [OFFSET] item and
set its ON direction. (Always ON at "--" setting)
touch the RTN button to switch to the data
input mode. Adjust the operation reference
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
point of each flap by scrolling the touch description at the back of this manual.
sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 83
[Corresponding model type]: Airplane/glider, 2 ailerons + 2 flaps or
$,/WR&0%)/3 more
7KLVPL[RSHUDWHVWKHFDPEHUIODSV)/3
in the aileron mode. When the aileron stick
LV PDQLSXODWHG WKH DLOHURQV DQG FDPEHU IODSV
perform aileron operation simultaneously to
VLJQL¿FDQWO\LPSURYHWKHUROOD[LV
ŏ 7KH DLOHURQ OHIWULJKW PL[LQJ UDWH RI HDFK ÁDS VHUYR
can be independently adjusted.
ŏ $Q 212)) VZLWFK FDQ EH VHW
ŏ /LQNLQJ LV SRVVLEOH /LQN WKLV PL[ WR RWKHU PL[HV FLP 1 FLP 2
(Camber Flap) (Camber Flap)
AIL1 AIL 2
(Main Aileron) (Main Aileron)
AIL 3 AIL 4
(Chip Aileron) (Chip Aileron)
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ $GMXVWPHQW RI HDFK
ÁDS VHUYR ŏ7R QH[W SDJH
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the flap (FLP) 1~2 left
or right item according to the wing type
and touch the RTN button to switch to the
data input mode. Adjust the mixing rate
independently by scrolling the touch sensor.
84 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
>&RUUHVSRQGLQJ PRGHO W\SH@ *OLGHU ÁDSV
$,/WR%5$.()/3
7KLV PL[ RSHUDWHV WKH EUDNH IODSV )/3
in the aileron mode. When the aileron stick is
PDQLSXODWHGWKHDLOHURQDQGEUDNHÀDSVSHUIRUP
the aileron operation simultaneously and the roll
axis is improved.
ŏ 7KH DLOHURQ OHIW DQG ULJKW PL[LQJ UDWHV FDQ EH
DGMXVWHG VHSDUDWHO\ IRU HDFK ÁDS VHUYR
FLP 3 FLP 4
ŏ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\ (Brake Flap) (Brake Flap)
setting a switch. (Always ON at [--] setting)
ŏ /LQNLQJ FDQ EH VHW /LQN WKLV PL[ WR RWKHU PL[HV
AIL1 AIL 2
(Main Aileron) (Main Aileron)
AIL 3 AIL 4
(Chip Aileron) (Chip Aileron)
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ $GMXVWPHQW RI HDFK
ÁDS VHUYR ŏ7R QH[W SDJH
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the flap (FLP) 3~4 left or
right item and touch the RTN button to switch
to the data input mode. Adjust the mixing
rate independently by scrolling the touch
sensor.
,QLWLDO YDOXH
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 85
[Corresponding model type]: Airplane/glider, general
AIL to RUD
8VHWKLVPL[ZKHQ\RXZDQWWRPL[WKHUXGGHUV
ZLWKDLOHURQRSHUDWLRQ7KLVDOORZVWKHDLUFUDIWWR
bank at a steep angle.
ŏ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\ D
AIL1 AIL 2
switch. (Always ON at [--] setting) (Main Aileron) (Main Aileron)
ŏ 7KH PL[LQJ UDWH FDQ EH DGMXVWHG AIL 3
(Chip Aileron)
AIL 3
(Chip Aileron)
RUDDER 1 RUDDER 2
Winglet Winglet
(at Flying wing) (at Flying wing)
V-TAIL
RUDDER 2
RUDDER RUDDER
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
6HWWLQJPHWKRG Ɣ0L[LQJUDWHDGMXVWPHQW
Ɣ$FWLYDWHWKHIXQFWLRQ Move the cursor to the left or right item
and touch the RTN button to switch to the
Move the cursor to the [ACT] item and touch data input mode. Adjust the mixing rate
the RTN button to switch to the data input independently by scrolling the touch sensor.
mode. Select the ACT mode by scrolling the ,QLWLDO YDOXH
touch sensor.
$GMXVWPHQW UDQJH a
*The display blinks.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
Touch the RTN button to activate the UHVHWWRWKHLQLWLDOYDOXH
function and return to the cursor mode. (ON
is displayed.) Touch the RTN button to end the adjustment
and return to the cursor mode.
When selecting a switch, move the cursor to
the [SW] item and touch the RTN button to
call the selection screen. Select the switch
and set its ON direction. (Always ON at "--"
setting)
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
description at the back of this manual.
86 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
[Corresponding model type]: Airplane/glider, general
RUD to AIL
7KLV IXQFWLRQ LV XVHG ZKHQ \RX ZDQW WR PL[
WKH DLOHURQV ZLWK UXGGHU LQSXW ,W LV XVHG ZKHQ
rudder is applied during roll maneuvers such
DV NQLIH HGJH IOLJKW ,W FDQ EH XVHG WR WXUQ RU
EDQNVFDOHPRGHOVODUJHPRGHOVHWFOLNHDIXOO AIL1 AIL 2
(Main Aileron) (Main Aileron)
size aircraft. AIL 3 AIL 3
(Chip Aileron) (Chip Aileron)
ŏ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\ RUDDER 1 RUDDER 2
setting a switch. (Always ON at [--] setting) Winglet
(at Flying wing)
Winglet
(at Flying wing)
ŏ /LQNLQJ FDQ EH VHW /LQN WKLV PL[ WR RWKHU PL[HV
ŏ 7KH PL[LQJ UDWH FDQ DOVR EH DGMXVWHG V-TAIL
RUDDER 2
RUDDER RUDDER
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
6HWWLQJPHWKRG
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Ɣ$FWLYDWHWKHIXQFWLRQ Touch the RTN button to end the adjustment
Move the cursor to the [ACT] item and touch and return to the cursor mode.
the RTN button to switch to the data input
Ɣ/LQNPRGHVHWWLQJ
mode. Select the ACT mode by scrolling the
touch sensor. To activate the link mixing, move the cursor
*The display blinks. to the [LINK] item and touch the RTN button
to switch to the data input mode. Select the
Touch the RTN button to activate the ON mode by scrolling the touch sensor.
function and return to the cursor mode. (ON
*The display blinks.
is displayed.)
When setting a switch, move the cursor to Touch the RTN button to set the link mode
the [SW] item and touch the RTN button to and return to the cursor mode.
call the selection screen. Select the switch
and set its ON direction. (Always ON at "--"
setting)
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
description at the back of this manual.
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the left or right item
and touch the RTN button to switch to the
data input mode. Adjust the mixing rate
independently by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 87
[Corresponding model type]: Airplane/glider, 2 ailerons or more
&$0%(50,;
7KLV IXQFWLRQ DGMXVWV WKH UDWH RI FDPEHU ŏ 7KH XSGRZQ VLGH UDWHV RI WKH DLOHURQ IODS DQG
RSHUDWLRQIRUWKHZLQJFDPEHUDLOHURQVFDPEHU elevator servos can be adjusted. When the mixing
direction is reversed by the linkage, adjustments
IODSV EUDNH IODSV LQ WKH QHJDWLYH DQG SRVLWLYH can be made by changing the mixing rate
GLUHFWLRQV7KH DLOHURQ IODS DQG HOHYDWRU UDWHV polarity (+ or -).
FDQDOVREHDGMXVWHGLQGHSHQGHQWO\DQGDWWLWXGH ŏ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\
changes caused by camber operation can be setting a switch. (Always ON at [--] setting)
corrected. ŏ $ FRQGLWLRQ GHOD\ FDQ EH VHW $ FXW VZLWFK ZKLFK
can turn OFF the delay function can be set.
,QLWLDOVHWWLQJDVVLJQVFDPEHURSHUDWLRQWRVLGHOHYHU/6
ŏ&RQGLWLRQ GHOD\
setting
ŏ7R QH[W SDJH
ŏ&RQGLWLRQ GHOD\
cut switch
*OLGHU&XUUHQWO\VHOHFWHG
FRQGLWLRQQDPH
ŏ$LOHURQ UDWH
adjustment
ŏ)ODS UDWH
adjustment
ŏ(OHYDWRU UDWH
adjustment
88 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
6HWWLQJPHWKRG When setting a cut switch, move the cursor
to the [CUT-SW] item and touch the RTN
Ɣ$FWLYDWHWKHIXQFWLRQ button to access the selection screen. Select
the switch and set its ON direction. (Always
Move the cursor to the [ACT] item and touch
ON at "--" setting)
the RTN button to switch to the data input
mode. Select the ACT mode by scrolling the
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
touch sensor. description at the back of this manual.
*The display blinks. Ɣ5DWHDGMXVWPHQW
Touch the RTN button to activate the The rates are adjusted by accessing the
function and return to the cursor mode. (ON DLOHURQÁDSDQGHOHYDWRUUDWHVFUHHQV
is displayed.)
Move the cursor to the rate1 or rate2
When setting a switch, move the cursor to item and touch the RTN button to switch
the [SW] item and touch the RTN button to to the data input mode. Adjust the rate
call the selection screen. Select the switch independently by scrolling the touch sensor.
and set its ON direction. (Always ON at "--"
setting) ,QLWLDOYDOXH
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH $GMXVWPHQWUDQJHa
description at the back of this manual.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Ɣ&RQGLWLRQGHOD\VHWWLQJ
Touch the RTN button to end the adjustment
Move the cursor to the [COND.DELAY] item and return to the cursor mode.
and touch the RTN button to switch to the
data input mode. Adjust the condition delay
by scrolling the touch sensor.
Initial value: 0
Adjustment range: 0~27
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
FLP 3 FLP 4
(Brake Flap) (Brake Flap)
FLP 1 FLP 2
(Camber Flap) (Camber Flap)
AIL1 AIL 2
(Main Aileron) (Main Aileron)
AIL 3 AIL 4
(Chip Aileron) (Chip Aileron)
V-TAIL AILVATOR
ELEVATOR
ELEVATOR 2 ELEVATOR ELEVATOR 2
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 89
[Corresponding model type]: Airplane/glider, 2 ailerons or more
ELE to CAMBER
7KLVIXQFWLRQLVXVHGZKHQ\RXZDQWWRPL[WKH ŏ ,QÁLJKW PL[LQJ FDQ EH WXUQHG 212)) E\ DVVLJQLQJ
FDPEHUÀDSVZLWKHOHYDWRURSHUDWLRQ:KHQXVHG this to a switch. (Always ON at [--] setting)
ŏ 7KH PL[LQJ UDWH FDQ EH DGMXVWHG
WKHIODSVDUH ORZHUHGE\XSHOHYDWRUDQGOLIWLV ŏ 7KH UDQJH WKDW PL[LQJ GRHV QRW ZRUN QHDU WKH
increased. neutral position of the elevator stick can be
adjusted. (Glider only)
ŏ 6HOHFW >(/( WR &$0%(5@ DW WKH 0RGHO
menu and access the setup screen 1RWH7KHHOHYDWRURQWKHWDLOOHVVZLQJZLOODOVR
shown below by touching the RTN EHHIIHFWHGZKHQWKLVPL[LVDFWLYDWHG
*OLGHU&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the up or down mixing
rate item for each servo and touch the RTN
button to switch to the data input mode.
Adjust the rate independently by scrolling
the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
90 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
[Corresponding model type]: Airplane/glider,
&0%)/3WR(/( DLOHURQV ÁDS RU PRUH
ELEVATOR
ELEVATOR 2 ELEVATOR ELEVATOR 2
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ(OHYDWRU UDWH
adjustment ŏ7R QH[W SDJH
6HWWLQJPHWKRG Ɣ0L[LQJUDWHDGMXVWPHQW
Ɣ$FWLYDWHWKHIXQFWLRQ Move the cursor to the RATE1 or RATE2 item
and touch the RTN button to switch to the
Move the cursor to the [ACT] item and touch data input mode. Adjust the mixing rate
the RTN button to switch to the data input independently by scrolling the touch sensor.
mode. Select the ACT mode by scrolling the ,QLWLDO YDOXH
touch sensor.
$GMXVWPHQW UDQJH a
*The display blinks.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
Touch the RTN button to activate the UHVHWWRWKHLQLWLDOYDOXH
function and return to the cursor mode. (ON
is displayed.) Touch the RTN button to end the adjustment
and return to the cursor mode.
When setting a switch, move the cursor to
the [SW] item and touch the RTN button to
call the selection screen. Select the switch
and set its ON direction. (Always ON at "--"
setting)
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
description at the back of this manual.
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 91
[Corresponding model type]: Glider, Normal: 2 ailerons or more
BUTTERFLY )O\LQJ DLOHURQV ÁDS RU PRUH
7KLV IXQFWLRQ LV XWLOL]HG WR TXLFNO\ VORZ WKH 3. Create more lift toward the center of the
aircraft and reduce altitude by simultaneously ZLQJ DOORZLQJ LW WR Á\ DW D VORZHU VSHHG
UDLVLQJWKHOHIWDQGULJKWDLOHURQVDQGORZHULQJWKH ŏ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\
setting a switch. (Always ON at [--] setting)
ÀDSVFDPEHUÀDSEUDNHÀDS
ŏ 7KH SRLQW DW ZKLFK WKH EXWWHUIO\ RSHUDWLRQ
%XWWHUIO\ &URZ SURGXFHV DQ H[WUHPHO\ reference point can be offset.
HI¿FLHQWODQGLQJFRQ¿JXUDWLRQE\DFFRPSOLVKLQJ ŏ 7KH RSHUDWLRQDO VSHHG RI WKH DLOHURQV DQG IODSV
WKHIROORZLQJ can be adjusted.
ŏ 7KH GLIIHUHQWLDO UDWH FDQ EH DGMXVWHG
1. Slow the aircraft’s velocity.
)RU D GHVFULSWLRQ RI WKH VHWWLQJ PHWKRG VHH WKH DLOHURQ
2. Provide washout at the wing tips to reduce differential function.
the tendency to tip stall.
ŏ 6HOHFW >%877(5)/<@ DW WKH 0RGHO PHQX *The display screen is an example. The actual
and access the setup screen shown screen depends on the model type.
below by touching the RTN button.
&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ$LOHURQÁDS UDWH
adjustment
ŏ7R QH[W SDJH
ŏ(OHYDWRU UDWH
adjustment
92 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
6HWWLQJPHWKRG Ɣ5HIHUHQFHSRLQWDGMXVWPHQW
Ɣ$FWLYDWHWKHIXQFWLRQ Move the cursor to the [OFFSET] item and
hold the airbrake stick to the desired position
Move the cursor to the [ACT] item and touch and then touch the RTN button for one
the RTN button to switch to the data input second to set the butterfly operational
mode. Select the ACT mode by scrolling the reference point.
touch sensor. ,QLWLDOYDOXHXSSHUVLGH
*The display blinks.
$GMXVWPHQWUDQJHa
Touch the RTN button to activate the
function and return to the cursor mode. (ON Ɣ6HUYRVSHHGVHWWLQJ
is displayed.) Move the cursor to the aileron, flap or
When setting a switch, move the cursor to elevator speed item and touch the RTN
the [SW] item and touch the RTN button to button to switch to the data input mode.
call the selection screen. Select the switch Adjust the rate by scrolling the touch sensor.
and set its ON direction. (Always ON at "--"
setting) Initial value: 0
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH Adjustment range: 0~27 (maximum delay)
description at the back of this manual.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Ɣ5DWHDGMXVWPHQW
Touch the RTN button to activate the
Move the cursor to the aileron, flap or function and return to the cursor mode.
elevator rate item and touch the RTN button
to switch to the data input mode. Adjust the
rate independently by scrolling the touch
sensor.
,QLWLDOYDOXH
$GMXVWPHQW UDQJH a (OHYDWRU
a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
FLP 3 FLP 4
(Brake Flap) (Brake Flap)
FLP 1 FLP 2
(Camber Flap) (Camber Flap)
AIL1 AIL 2
(Main Aileron) (Main Aileron)
AIL 3 AIL 4
(Chip Aileron) (Chip Aileron)
V-TAIL AILVATOR
ELEVATOR
ELEVATOR 2 ELEVATOR ELEVATOR 2
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 93
[Corresponding model type]: Glider, 2 ailerons or more
75,00,;
7KLVIXQFWLRQDGMXVWVWKHWULPRIIVHWUDWHVRIWKH VPRRWKWUDQVLWLRQEHWZHHQWKHWZRFRQGLWLRQV,W
DLOHURQVHOHYDWRUVDQGÀDSVFDPEHUÀDSVEUDNH LV DOVR SRVVLEOH WR SURJUDP D FXW VZLWFK ZKLFK
ÀDSVDFFRUGLQJWRWKHÀLJKWVWDWXV ZLOOWXUQRIIWKHGHOD\
As an example this function can be set up for )XUWKHUPRUH\RXFDQVHWWKHDXWRVZLWFKZKLFK
ODXQFKLQJZLWKVSHHGÀDSVDQGDLOHURQVGURRSHG ZLOOOLQNWKHWULPPL[WRDVWLFNVZLWFKRUGLDO
DQG D VOLJKW DPRXQW RI XS HOHYDWRU DQG FDQ EH $GGLWLRQDOO\WKHVSHHGRIWKHDLOHURQHOHYDWRU
XVHGIRUKLJKVSHHGÀ\LQJZLWKERWKDLOHURQVDQG DQGÀDSVHUYRVFDQEHDGMXVWHG
VSHHGIODSVUHIOH[HGVOLJKWO\DQGDELWRIGRZQ
elevator.
7RSUHYHQWVXGGHQWULPFKDQJHVZKHQVZLWFKLQJ
ÀLJKWFRQGLWLRQVDGHOD\FDQEHVHWWRSURYLGHD
ŏ 6HOHFW >75,0 0,;@ DW WKH 0RGHO PHQX *The display screen is an example. The actual
and access the setup screen shown screen depends on the model type.
below by touching the RTN button.
&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ6ZLWFK
selection
94 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
6HWWLQJPHWKRG Initial value: 0
Adjustment range: 0~27
Ɣ$FWLYDWHWKHIXQFWLRQ
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR
Move the cursor to the [ACT] item and touch RSHUDWLRQSRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
the RTN button to switch to the data input Touch the RTN button to end the adjustment
mode. Select the ACT mode by scrolling the and return to the cursor mode.
touch sensor.
When setting a cut switch, move the cursor
*The display blinks.
to the [CUT-SW] item and touch the RTN
Touch the RTN button to activate the button to access the selection screen. Select
function and return to the cursor mode. (ON the switch and set its ON direction. (Always
is displayed.) ON at "--" setting)
When setting a switch, move the cursor to
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
the switch item and touch the RTN button description at the back of this manual.
to access the selection screen. Select the
switch and set its ON direction. (Always ON Ɣ6HUYRVSHHGVHWWLQJ
at "--" setting) Move the cursor to the aileron, flap or
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH elevator speed item and touch the RTN
description at the back of this manual. button to switch to the data input mode.
Ɣ7ULPRIIVHWUDWHDGMXVWPHQW Adjust the rate by scrolling the touch sensor.
Initial value: 0
Move the cursor to the aileron, flap or
elevator rate item and touch the RTN button Adjustment range: 0~27 (maximum delay)
to switch to the data input mode. Adjust the
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
rate independently by scrolling the touch UHVHWWRWKHLQLWLDOYDOXH
sensor. Touch the RTN button to activate the
,QLWLDOYDOXH function and return to the cursor mode.
$GMXVWPHQWUDQJHa Ɣ$XWRVZLWFKVHOHFWLRQ
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH When selecting an auto switch, move the
cursor to the [AUTO-SW] item and touch the
Touch the RTN button to end the adjustment RTN button to access the selection screen.
and return to the cursor mode. Select the switch and set its ON direction.
Ɣ&RQGLWLRQGHOD\VHWWLQJ (Always ON at "--" setting)
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
Move the cursor to the [COND.DELAY] item description at the back of this manual.
and touch the RTN button to switch to the
data input mode. Adjust the condition delay
by scrolling the touch sensor.
FLP 3 FLP 4
(Brake Flap) (Brake Flap)
FLP 1 FLP 2
(Camber Flap) (Camber Flap)
AIL1 AIL 2
(Main Aileron) (Main Aileron)
AIL 3 AIL 4
(Chip Aileron) (Chip Aileron)
V-TAIL AILVATOR
ELEVATOR
ELEVATOR 2 ELEVATOR ELEVATOR 2
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 95
[Corresponding model type]: Airplane, 2 ailerons or more
AIRBRAKE
This function is used to increase the aircraft's 6HWWLQJH[DPSOHIRU)$DQGRWKHUÀDSHURQVSHFL¿FDWLRQV
GUDJDQGLVXVHIXOIRUODQGLQJRUGLYLQJHWF (When 2 ailerons model type selected)
7KH SUHVHW HOHYDWRUV DQG IODSV FDPEHU IODS Offset rate:
EUDNHIODSRIIVHWDPRXQWFDQEHDFWLYDWHGE\D $,/ >a@ $,/ >a@ (/( >a@
VZLWFK 1RWH7KHLQSXWQXPHULFVDUHH[DPSOHV$GMXVWWKHWUDYHOWR
match the aircraft.
7KHRIIVHWDPRXQWRIWKHDLOHURQHOHYDWRUDQG
Mode setting:
IODSVHUYRVFDQEHDGMXVWHGDVQHHGHG$OVRWKH
ACT: [ON]
VSHHGRIWKHDLOHURQHOHYDWRUDQGÀDSVHUYRVFDQ Switch: [SW-C]
EHDGMXVWHG,IWKH$XWR0RGH LVDFWLYDWHGWKLV AUTO-SW: [--]
ZLOOOLQNWKH$LUEUDNHWRDVWLFNVZLWFKRUGLDO$
VHSDUDWHVWLFNVZLWFKRUGLDOFDQDOVREHVHWDVWKH
212))VZLWFK
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ6ZLWFK
selection
ŏ $LOHURQV IODSV DQG
elevators servo speed
setting
96 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
6HWWLQJPHWKRG Ɣ6HUYRVSHHGVHWWLQJ
Ɣ$FWLYDWHWKHIXQFWLRQ Move the cursor to the aileron, flap or
elevator speed item and touch the RTN
Move the cursor to the [ACT] item and touch button to switch to the data input mode.
the RTN button to switch to the data input Adjust the rate by scrolling the touch sensor.
mode. Select the ACT mode by scrolling the
touch sensor. Initial value: 0
*The display blinks. Adjustment range: 0~27 (maximum delay)
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
Touch the RTN button to activate the
UHVHWWRWKHLQLWLDOYDOXH
function and return to the cursor mode. (ON
is displayed.) Touch the RTN button to return to the cursor
When setting a switch, move the cursor to mode.
the switch item and touch the RTN button Ɣ$XWRVZLWFKVHOHFWLRQ
to access the selection screen. Select the
switch and set its ON direction. (Always ON When setting a auto switch, move the cursor
at "--" setting) to the [AUTO-SW] item and touch the RTN
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH button to access the selection screen. Select
description at the back of this manual. the switch and set its ON direction. (Always
ON at "--" setting)
Ɣ2IIVHWUDWHDGMXVWPHQW
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
description at the back of this manual.
Move the cursor to the aileron, flap or
elevator rate item and touch the RTN button
to switch to the data input mode. Adjust the
rate independently by scrolling the touch
sensor.
,QLWLDOYDOXH
$GMXVWPHQWUDQJHa
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
FLP 3 FLP 4
(Brake Flap) (Brake Flap)
FLP 1 FLP 2
(Camber Flap) (Camber Flap)
AIL1 AIL 2
(Main Aileron) (Main Aileron)
AIL 3 AIL 4
(Chip Aileron) (Chip Aileron)
V-TAIL AILVATOR
ELEVATOR
ELEVATOR 2 ELEVATOR ELEVATOR 2
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 97
[Corresponding model type]: Airplane/glider, general
GYRO
7KLVIXQFWLRQLVXVHGZKHQD*<$6HULHVJ\UR Note: This setting does not assign a sensitivity
is used to stabilize the aircraft's attitude. The channel. To do so, use the Linkage menu
prior to assigning the sensitivity channel
VHQVLWLYLW\ DQG RSHUDWLRQ PRGH 1RUPDO PRGH
(Gyro/Gyro2/Gyro3), be sure to select an
$9&6PRGHFDQEHFKDQJHGYLDDVZLWFK unused channel.
ŏ 7KUHH UDWHV 5DWH 5DWH 5DWH FDQ EH
switched.
Set the [Control] and [Trim] settings other than
ŏ 8S WR D[HV *\UR*\UR *\UR FDQ EH
Function to [--].
simultaneously controlled.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ 5 D W H V H W X S
screen selection ŏ7R QH[W SDJH
ŏ * \ U R W \ S H
selection ŏ $&7,1+
ŏ 7KH RSHUDWLRQ PRGH $9&6125
ŏ 6ZLWFK VHOHFWLRQ and sensitivity of the three axis
[Rate 2 setup screen] Gyro/Gyro2/Gyro3 can be set.
98 0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV!
6HWWLQJPHWKRG Ɣ6HQVLWLYLW\VHWWLQJ
3ULRUWRXVLQJWKH)XQFWLRQPHQXLQWKH/LQNDJHPHQXWR Move the cursor to the sensitivity item and
DVVLJQWKHVHQVLWLYLW\FKDQQHO*\UR*\UR*\URVHOHFWDQ touch the RTN button to switch to the data
unused channel. input mode.
Set [Control] and [Trim] other than function to [--]. Adjust the sensitivity by scrolling the touch
sensor.
Ɣ5DWHVHWXSVFUHHQVHOHFWLRQ ,QLWLDOYDOXH
Move the cursor to the setup screen selection $GMXVWPHQWUDQJHa
item and touch the RTN button to switch
:KHQ WKH 571 EXWWRQ LV WRXFKHG IRU RQH VHFRQG WKH
to the data input mode. Select the setup VHQVLWLYLW\LVUHVHWWRWKHLQLWLDOYDOXH
screen # by scrolling the touch sensor.
Touch the RTN button to return to the cursor
Touch the RTN button to change the setup mode.
screen and return to the cursor mode.
Ɣ$FWLYDWHWKHIXQFWLRQ
Move the cursor to the [INH] item and touch
the RTN button to switch to the data input
mode. Select the ACT mode by scrolling the
touch sensor.
*The display blinks.
Touch the RTN button to activate the
function and return to the cursor mode.
When setting a rate selection switch, move
the cursor to the switch item and touch the
RTN button to access the selection screen.
Select the switch and set its ON direction.
(Always ON at "--" setting)
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
description at the back of this manual.
Ɣ*\URW\SHVHOHFWLRQ
Move the cursor to the gyro type selection
item and touch the RTN button to switch to
the data input mode. Select the gyro type
by scrolling the touch sensor.
[GY]: When a Futaba GYA gyro is used
[NORM]: When using something other than
Futaba GYA gyro is used.
Touch the RTN button to change the gyro
type and return to the cursor mode.
:KHQD)XWDED*<$J\URLVXVHGDQG>*<@W\SHLVVHOHFWHG
the sensitivity set value is directly read in both the AVCS
DQG1250PRGHV
Ɣ2SHUDWLRQPRGHVHOHFWLRQ*<$J\UR
Move the cursor to the operation mode
selection item and touch the RTN button
to switch to the data input mode. Select
the operation mode by scrolling the touch
sensor.
[AVCS]: AVCS mode
[NORM]: Normal mode
Touch the RTN button to change the
operation mode and return to the cursor
mode.
0RGHO0HQX$LUSODQH*OLGHU)XQFWLRQV! 99
[Corresponding model type]: Airplane/glider, V-tail
V-TAIL
7KLV IXQFWLRQ HQDEOHV DGMXVWPHQWV IRU OHIW DQG V-TAIL
right rudder angle changes during elevator and
rudder operation of a V-tail airplane.
9WDLOLVZKHQWZRVHUYRVDUHXVHGWRJHWKHUWR
control rudder movement as elevators. In addition
WRHDFKHOHYDWRUVLGHPRYLQJXSDQGGRZQWRJHWKHU ELEVATOR
HDFKVLGHPRYHVLQRSSRVLWHGLUHFWLRQVZKHQPRYLQJ (RUDDER 2)
DV UXGGHUV 2Q D9WDLO WKLV LV DOVR NQRZQ DV D RUDDER
(ELEVATOR 2)
5XGGHUYDWRUDVWKH\VHUYHWKHVDPHSXUSRVH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
6HWWLQJPHWKRG
Ɣ7UDYHODGMXVWPHQW
Move the cursor to the item you want to
adjust and touch the RTN button to switch to
the data input mode.
Adjust the rate by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to return to the cursor
mode.
,IWKHPL[LQJGLUHFWLRQLVUHYHUVHGDGMXVWPHQWVFDQEHPDGH
E\FKDQJLQJWKHPL[LQJUDWHSRODULW\RU
,IDODUJHYDOXHRIWUDYHOLVVSHFLILHGZKHQWKHVWLFNVDUH
PRYHGDWWKHVDPHWLPHWKHFRQWUROVPD\ELQGRUUXQRXWRI
travel. Decrease the travel until no binding occurs.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
6HWWLQJPHWKRG
,IWKHPL[LQJGLUHFWLRQLVUHYHUVHGDGMXVWPHQWVFDQEHPDGH
E\FKDQJLQJWKHPL[LQJUDWHSRODULW\RU
Ɣ7UDYHODGMXVWPHQW
,IDODUJHYDOXHRIWUDYHOLVVSHFLILHGZKHQWKHVWLFNVDUH
Move the cursor to the item you want to PRYHGDWWKHVDPHWLPHWKHFRQWUROVPD\ELQGRUUXQRXWRI
adjust and touch the RTN button to switch to travel. Decrease the travel until no binding occurs.
the data input mode.
Adjust the rate by scrolling the touch sensor.
,QLWLDO YDOXH (/( $,/
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to return to the cursor
mode.
UDWLRZLQJZLWKRXWDGGLQJJUHDWO\WRWKHVWUXFWXUDO
VWUHVVDQGKHQFHQHFHVVDU\ZHLJKWRILWVVWUXFWXUH RUDDER 2
Winglet
DQ H[WHQVLRQ RI ZLQJ VSDQ ZRXOG DOVR SHUPLW (at Flying wing)
ORZHULQJRILQGXFHGGUDJWKRXJKLWZRXOGFDXVH
SDUDVLWLF GUDJ DQG ZRXOG UHTXLUH ERRVWLQJ WKH
VWUHQJWKRIWKHZLQJDQGKHQFHLWVZHLJKW7KHUH
ZRXOG FRPH D SRLQW DW ZKLFK QR RYHUDOO XVHIXO
JDLQVZRXOGEHPDGH$ZLQJOHWKHOSVWRVROYHWKLV
E\HIIHFWLYHO\LQFUHDVLQJWKHDVSHFWUDWLRZLWKRXW
DGGLQJWRWKHVSDQRIWKHZLQJ
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
(Rudder 1/2)
6HWWLQJPHWKRG ŏ 7KH WUDYHO GXULQJ UXGGHU VWLFN RSHUDWLRQ
can be individually adjusted.
Ɣ7UDYHODGMXVWPHQW
Move the cursor to the item you want to
adjust and touch the RTN button to switch to
the data input mode.
Adjust the rate by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to return to the cursor
mode.
,IWKHPL[LQJGLUHFWLRQLVUHYHUVHGFKDQJHWKHPL[LQJUDWH
SRODULW\RU
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
6HWWLQJPHWKRG Note:
ŏ)LUVWGHFLGHWKHPRWRU2))GLUHFWLRQDQGWKHQ
Ɣ$FWLYDWHWKHIXQFWLRQ set the speed. When you want to reset the
When using this function, move the cursor to motor OFF direction, also reset the speed.
the [ACT/INH] item and touch the RTN button ŏ :H UHFRPPHQG WKDW 0RWRU 2)) EH VHW LQ
to switch to the data input mode. Select the combination with F/S.
[ACT] by scrolling the touch sensor and touch ŏ 6HW WKH EDVLF RSHUDWLRQ GLUHFWLRQ ZLWK WKH
the RTN button. Reverse function to match the ESC used.
When selecting the ON/OFF switch, move the ŏ$OZD\VVHWWKH0RWRU2))SRVLWLRQ
cursor to the switch item and touch the RTN
button to access the selection screen. Select
the switch and set its ON direction. (Always
ON at "--" setting)
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
description at the back of this manual.
Ɣ0RWRURIISRVLWLRQVHWWLQJ
Move the cursor to the [MOTOR OFF] item
and touch the RTN button for one second
when the motor function switch (SG, etc.) is
in the motor OFF position you want to set. The
direction of the motor switch is memorized.
The screen graph display OFF direction also
changes.
6HWWLQJPHWKRG Ɣ6HW5HVHWWKHRQHWLPHRSHUDWLRQ
Ɣ$FWLYDWHWKHPRWRUVSHHGIXQFWLRQ Move the cursor to the [ONE TIME] item and
touch the RTN button to switch to the data
When using motor speed function, move the input mode.
cursor to the [INH] item and touch the RTN Select the [ACT] by scrolling the touch sensor
button to switch to the data input mode. and touch the RTN button to set the one time
Select the [ACT] by scrolling the touch sensor operation.
and touch the RTN button.
:KHQ\RXZDQWWRUHVHWRQHWLPHRSHUDWLRQVHWWKH$&7
Ɣ6LIWLQJWKHERXQGDU\EHWZHHQWKHUDQJHV ,1+LWHPWR>,1+@DQGWKHQUHVHWLWWR>21@
Move the cursor to the [SPEED 1>2] item and
touch the RTN button to switch to the data
input mode.
Adjust the boundary position by scrolling the
touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to return to the cursor
mode.
Ɣ2SHUDWLRQVSHHGDGMXVWPHQW
Move the cursor to the [IN] (on to off) or [OUT]
(off to on) item and touch the RTN button to
switch to the data input mode.
Adjust the operation speed you want to set
by scrolling the touch sensor.
Initial value: 0
Adjustment range: 0~27
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to return to the cursor
mode.
6HWWLQJPHWKRG Ɣ/LQNPRGHVHWWLQJ
Ɣ$FWLYDWHWKHIXQFWLRQ When selecting the link mixing, move the
cursor to the [LINK] item and touch the RTN
Move the cursor to the [ACT] item and touch button to switch to the data input mode.
the RTN button to switch to the data input Select the ON mode by scrolling the touch
mode. Select the ACT mode by scrolling the sensor.
touch sensor. *The display blinks.
*The display blinks.
Touch the RTN button to set the link mode
Touch the RTN button to activate the and return to the cursor mode.
function and return to the cursor mode. (ON
is displayed.)
When selecting a switch, move the cursor to
the [SW] item and touch the RTN button to
call the selection screen. Select the switch
and set its ON direction. (Always ON at "--"
setting)
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
description at the back of this manual.
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the left or right item
and touch the RTN button to switch to the
data input mode. Adjust the mixing rate
independently by scrolling the touch sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ 0DVWHUVLQJOH PRGH
selection
ŏ 'LUHFWLRQ VZLWFKHV
Ɣ5DWHDGMXVWPHQW
Move the cursor to the aileron, elevator or
rudder item for each direction and touch the
RTN button to switch to the data input mode.
Adjust the rate independently by scrolling
the touch sensor.
Initial value: (Dependent upon the snap roll
direction)
$GMXVWPHQWUDQJHa
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the
RTN button.
3,7&859($GMXVWVSLWFKVHWWLQJVLQGLIIHUHQWÀLJKWFRQGLWLRQV
THR CURVE:7KURWWOHFXUYHDQGKRYHULQJWULPDGMXVWPHQWLQGLIIHUHQWÀLJKWFRQGLWLRQV
THR HOLD:0RYHVWKHWKURWWOHWRLGOHGXULQJDXWRURWDWLRQ
6:$6+0,; &RPSHQVDWHVFRQWUROUHVSRQVHLQGLIIHUHQWÀLJKWFRQGLWLRQV
7+5277/(0,; &RPSHQVDWHVIRUSRZHUORVVZKHQF\FOLFDSSOLHG
3,7WR1(('/($GMXVWVSLWFKUHVSRQVHLQGLIIHUHQWÀLJKWFRQGLWLRQV
3,7WR58'&RPSHQVDWHVWRUTXHFKDQJHVIURPSLWFKDQJOHLQSXWV
GYRO:8VHGWRVZLWFKJ\URVHQVLWLYLW\
GOVERNOR:8VHGWRVZLWFK530RIWKHKHOLFRSWHU¶VKHDG
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
Ɣ3LWFK&XUYH([DPSOH
Normal Curve Idle-up 1 Curve Idle-up 2 Curve Hold Curve
3LWFK7ULP+RYHULQJSLWFKKLJKSLWFKORZSLWFK
+RYHULQJSLWFKWULP 6HWWLQJPHWKRG
The Hovering Pitch trim function trims the pitch ŏ 6HW WKH IXQFWLRQ WR $&7 >21@ LQLWLDO VHWWLQJ
QHDUWKHKRYHULQJSRLQW1RUPDOO\LWLVXVHGZLWK ŏ 6HOHFW WKH DGMXVWPHQW NQRE
the hovering condition. The hovering pitch can be Selection example: LD (initial setting)
¿QHWXQHGIRUFKDQJHVLQURWRUVSHHGDFFRPSDQ\LQJ ŏ 7KH WULP RSHUDWLRQ PRGH 0RGH &750
FKDQJHVLQWHPSHUDWXUHKXPLGLW\DQGRWKHUÀLJKW NORM) can be selected.
FRQGLWLRQV$GMXVW WKH KRYHULQJ SLWFK VR WKDW CTRM mode: Maximum amount of change
rotor speed is constant. This function can be used near center by center trim operation
WRJHWKHUZLWKWKH+RYHULQJ7KURWWOH7ULPIXQFWLRQ (recommended)
for more precise operation. NORM mode: Normal trim (parallel
movement trim) operation. The advantage
of using this mode is that the hovering pitch
can be adjusted without changing the
curve.
ŏ 7KH WULP UDWH FDQ EH DGMXVWHG DQG WKH
operation direction can be changed.
ŏ 7ULP DGMXVWPHQW UDQJH 5DQJH VHWWLQJ
When this value is made small, trim can only
be used near the center.
+LJK3LWFK/RZ3LWFK7ULP 6HWWLQJPHWKRG
+LJK 3LWFK/RZ 3LWFK7ULP LV WKH SLWFK VHUYR ŏ 6HW WKH IXQFWLRQ WR $&7 21
KLJKVLGHDQGORZVLGHWULPIXQFWLRQ ŏ 6HOHFW WKH DGMXVWPHQW NQREV
Selection example: LS (high side), RS (low
side)
ŏ 7KH WULP UDWH FDQ EH DGMXVWHG DQG WKH
operation direction can be changed.
ŏ 7ULP DFWV DV KLJK VLGH RU ORZ VLGH WULP ZLWK WKH
center as the standard.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
Ɣ7KURWWOH&XUYH([DPSOH
Normal Curve Idle-up 1 Curve Idle-up 2 Curve
7KURWWOH+RYHUWULP
6HWWLQJPHWKRG
ŏ 6HW WKH IXQFWLRQ WR $&7 >21@ LQLWLDO VHWWLQJ
ŏ 6HOHFW WKH DGMXVWPHQW NQRE
Selection example: RD (initial setting)
ŏ 7KH WULP RSHUDWLRQ PRGH 0RGH &750
NORM) can be selected.
CTRM mode: Maximum rate of change
near center by center trim operation
(recommended)
NORM mode: Normal trim (horizontal
movement trim) operation.
ŏ 7KH WULP UDWH FDQ EH DGMXVWHG DQG WKH
operation direction can be set.
ŏ 7ULP DGMXVWPHQW UDQJH 5DQJH VHWWLQJ
With smaller values, the trim is only active
near the center.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
6HWWLQJPHWKRG Ɣ6HUYRVSHHGVHWWLQJ
Ɣ+ROGFRQGLWLRQVZLWFKVHOHFWLRQ Move the cursor to the servo speed item and
touch the RTN button to switch to the data
Use the Condition select menu of the Model input mode.
menu to assign the hold condition switch. Adjust the rate by scrolling the touch sensor.
Selection example: SG Initial value: 0
Ɣ+ROGSRVLWLRQDGMXVWPHQW Adjustment range: 0~27 (maximum delay)
Move the cursor to the hold position item
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
and touch the RTN button to switch to the UHVHWWRWKHLQLWLDOYDOXH
data input mode. Touch the RTN button to return to the cursor
Adjust the rate by scrolling the touch sensor. mode.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
+ROGSRVLWLRQVHWVWKHWKURWWOHFXWSRVLWLRQ$GMXVWLWVRWKDW
the carburetor is completely closed. 2SHUDWLRQSUHFDXWLRQV
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
:DUQLQJ
Touch the RTN button to end the adjustment
and return to the cursor mode.
:KHQDFWXDOO\VWDUWLQJWKHHQJLQHDQGIO\LQJ
DOZD\VVHWWKHLGOHXSFRQGLWLRQVZLWFKWR2))
and start the engine at idle.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ&RQGLWLRQ VHOHFWLRQ
ŏ7R QH[W SDJH
6HWWLQJPHWKRG
Ɣ$FWLYDWHWKHPL[LQJ
When using this function, move the cursor to
the [ACT] item and touch the RTN button to
switch to the data input mode.
Select the ACT mode by scrolling the touch
sensor.
*The display blinks.
Touch the RTN button to activate the mixing
and return to the cursor mode. (ON is
displayed.)
Ɣ7ULPPRGH212))VHWWLQJ
[Switch selection]
When changing the trim mode, move the
When [ [--]] is set, the swash mixing function is cursor to the [TRIM] item and touch the RTN
operated by merely selecting the condition. button to switch to the data input mode.
When setting an [ON]/[OFF] switch, move the Select ON/OFF by scrolling the touch sensor.
cursor to the [SW] item and touch the RTN *The display blinks.
button to access the selection screen. Set
the switch and its ON position. Touch the RTN button to change the trim
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH
mode ON/OFF and return to the cursor
description at the back of this manual.
mode.
:KHQ PL[LQJ LQFOXGHV PDVWHU VLGH WULP VHOHFW >21@ DQG
Ɣ0L[LQJUDWHDGMXVWPHQW ZKHQPL[LQJGRHVQRWLQFOXGHPDVWHUWULPVHOHFW>2))@
Move the cursor to the mixing rate item you
want to correct and touch the RTN button
to switch to the data input mode. Adjust the
rate independently by scrolling the touch
sensor.
,QLWLDO YDOXH
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
ŏ&RQGLWLRQ VHOHFWLRQ
ŏ7R QH[W SDJH
6HWWLQJPHWKRG sensor.
,QLWLDO YDOXH
Ɣ$FWLYDWHWKHPL[LQJ
$GMXVWPHQW UDQJH a
When using this function, move the cursor to
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
the [ACT] item and touch the RTN button to UHVHWWRWKHLQLWLDOYDOXH
switch to the data input mode.
Touch the RTN button to end the adjustment
Select the ACT mode by scrolling the touch
and return to the cursor mode.
sensor.
*The display blinks. Ɣ2SHUDWLRQPRGHVHWWLQJ
Touch the RTN button to activate the mixing Move the cursor to the [MODE] item and
and return to the cursor mode. (ON is touch the RTN button to switch to the data
displayed.) input mode.
[Switch selection] Select the operation mode by scrolling the
touch sensor.
When [ [--]] is set, the swash mixing function is
operated by merely selecting the condition. *The display blinks.
When setting an [ON]/[OFF] switch, move the CTRM mode: Corrects near the center only.
cursor to the [SW] item and touch the RTN LIN. mode: Corrects the complete range.
button to call the selection screen. Set the Touch the RTN button to change the
switch and its ON position. operation mode and return to the cursor
)RU D GHVFULSWLRQ RI WKH VZLWFK VHOHFWLRQ PHWKRG VHH WKH mode.
description at the back of this manual.
Ɣ0L[LQJUDWHDGMXVWPHQW
Move the cursor to the mixing rate item you
want to correct and touch the RTN button
to switch to the data input mode. Adjust the
rate independently by scrolling the touch
6HWWLQJPHWKRG 1RUPDOFRQGLWLRQPL[LQJFXUYH!
Ɣ$FWLYDWHWKHPL[LQJ The mixing curve rate should be started
using smaller values.
When using this function, move the cursor to
For a rotor with a clockwise operation
the [ACT] item and touch the RTN button to
direction, when pitch was input at the plus
switch to the data input mode.
side, set these parameters so that mixing
Select the ACT mode by scrolling the touch is in the clockwise direction. First, trim at
sensor. hovering and then adjust the neutral
*The display blinks. position.
Touch the RTN button to activate the mixing 1. Adjustment between slow and hovering
and return to the cursor mode. (ON is Repeatedly hover from take off and land
displayed.) at a constant rate matched to your own
ƔSRLQWFXUYHVHWWLQJ rhythm. Then adjust the pitch so that the
nose of the helicopter remains steady
Move the cursor to the curve rate setting when the throttle is raised and lowered.
item you want to adjust and touch the RTN 2. Throttle high side (climbing and diving from
button to switch to the data input mode. hovering)
Adjust the rate by scrolling the touch sensor. Repeat climbing and diving from hovering
,QLWLDO YDOXH 3a3 at a constant rate matched to your own
$GMXVWPHQW UDQJH a rhythm and adjust the pitch so that the nose
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV does not deflect when the throttle is raised
UHVHWWRWKHLQLWLDOYDOXH and lowered.
Touch the RTN button to end the adjustment
and return to the cursor mode. ,GOHXSFRQGLWLRQPL[LQJFXUYH!
Repeat this procedure for each point.
Set the mixing rate so that the rudder direction
Ɣ3LWFKFXUYHFRS\IXQFWLRQ DW KLJKVSHHG ÁLJKW LV VWUDLJKW DKHDG $GMXVW IRU
each condition used.
Move the cursor to COPY item and touch the
RTN button to switch to the data input mode.
Select the copy destination condition by
scrolling the touch sensor and touch the RTN
button. Select the [YES] and touch the RTN
button.
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the Model ŏ0RYLQJ FXUVRU
menu by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
<SensorTouch™>
ŏ6HOHFW WKH IXQFWLRQ QDPH Scrolling
and return to the home ŏ0RYLQJ FXUVRU
screen by touching the ŏ6HOHFWLQJ PRGH
RTN button. ŏ$GMXVWLQJ YDOXH
120 $SSHQGL[!
6ZLWFK6HWWLQJ0HWKRG
The various functions used in the T8FG can LVZKHQHYHUWKHPDQXDOLQGLFDWHVWKDWVRPHWKLQJLV
EHDFWLYDWHGE\DVZLWFK)RUWKHSXUSRVHVRIWKLV RSHUDWHGYLDDVZLWFKLWLVSRVVLEOHIRUWKHXVHUWR
PDQXDODVWLFNSRVLWLRQ95SRVLWLRQHWFVKDOOEH DFWLYDWHWKLVVHWWLQJYLDDVWLFNVWLFNSRVLWLRQHWF
FRPPRQO\UHIHUUHGWRDVDVZLWFKLQDOOFDVHV7KDW
6ZLWFKVHOHFWLRQ
:KHQDVZLWFKLVVHOHFWHGDWDPL[LQJIXQFWLRQHWFWKHVHOHFWLRQVFUHHQVKRZQEHORZLVFDOOHG
(Switch selection screen example)
6ZLWFKVHOHFWLRQ :KHQVWLFNWULPOHYHURUNQREVHOHFWHG
1. Use the touch sensor to move the cursor :KHQDVWLFNWULPOHYHURUNQRELVXVHGDVD
(highlights) to the switch you want to VZLWFKWZRRSHUDWLRQPRGHVFDQEHVHOHFWHG
select and touch the RTN button.
7KHVZLWFKEOLQNV
2. To return to the preceeding screen, move
the cursor to the [H/W SELECT] at the top
of the screen and touch the RTN button.
Or, move the cursor to the [ON/OFF] and 1. When you want to change the mode,
call the ON/OFF position setting screen by move the cursor to [MODE] item and
touching the RTN button. touch the RTN button to switch to the
data input mode. Switch the display
to the mode you want to change by
:KHQVZLWFKLVVHOHFWHG scrolling the touch sensor and then make
the change by touching the RTN button.
:KHQVZLWFKZDVVHOHFWHG212))SRVLWLRQ ŏMode: [LIN]/[SYM]
setting is also performed.
*6HWWKH212IISRLQWE\WKHPHWKRGGHVFULEHGRQWKHQH[WSDJH
7KH212))VHWWLQJVWDWHRIHDFKSRVLWLRQLVGLVSOD\HG
$OWHUQDWHPRGHVHWWLQJ
1. When you want to change the ON/OFF ŏ$/7(51$7( mode: [OFF]/[ON]
setting, use the touch sensor to move the 1. Move the cursor to the [ALTERNATE] item
cursor and touch the RTN button to switch and touch the RTN button to switch to the
to the data input mode. Switch the ON/ data input mode.
Off display by scrolling the touch sensor. 2. Change to the mode you want to set by
212))GLVSOD\EOLQNV scrolling the touch sensor.
3. When the RTN button is touched, the *The mode display blinks.
ON/OFF setting is changed. (Touch the S1 3. Touch the RTN button. (Touch the S1 button
button to stop the change.) to stop the change.)
4. To return to the preceeding screen, move 4. To return to the preceeding screen, move
the cursor to the [ON/OFF] at the top of the cursor to the [ON/OFF] at the top of the
the screen and touch the RTN button. screen and touch the RTN button.
$SSHQGL[! 121
2SHUDWLRQPRGHV 6KLIWLQJWKH212IISRLQW
7KHRSHUDWLRQPRGHVDYDLODEOHZKHQVWLFNWULP 7KH212))SRLQWFDQEHVKLIWHG212))DW
OHYHURUNQREZDVVHOHFWHGDUHGHVFULEHGEHORZ a free position can be changed.
/LQHDUPRGH>/,1@
[Setting method]
7KLVPRGHVHWV212))WRWKHOHIWRUULJKWXS
1. First, use the touch sensor to move the
RUGRZQZLWKWKHVHWSRLQWDVWKHUHIHUHQFH
cursor to the [POS] item.
2. Move the stick, trim lever, or knob to the
6\PPHWULFDOPRGH>6<0@ point you want to change and touch the
RTN button. The point is shifted.
3. To return to the preceeding screen, move
the cursor to the [ON/OFF] at the top of
the screen and touch the RTN button.
122 $SSHQGL[!
/RJLFVZLWFK&RQGLWLRQ6HOHFWIXQFWLRQRQO\
7KHORJLFVZLWFKIXQFWLRQOHWV\RXWXUQRSHUDWLRQRQDQGRIIE\FRPELQLQJWZRVZLWFKHV
/RJLFPRGH
AND: When both switches are ON, the
condition is ON.
OR: When either switche is ON, the
condition is ON.
EOR: When the two switches are in different
states, the condition is ON.
6ZLWFKPRGHVHOHFWLRQ
1. Move the cursor to the [SINGLE] item and
touch the RTN button to switch to the data
input mode.
2. Select the [LOGIC] by scrolling the touch
sensor.
>/2*,&@GLVSOD\EOLQNV
3. Touch the RTN button to change to the
logic switch mode.
(Logic switch setting screen)
/RJLFPRGHVHOHFWLRQ
1. Move the cursor to the logic mode item
and touch the RTN button to switch to the
data input mode.
2. Select the logic mode by scrolling the
touch sensor. [AND, OR or EOR]
*The mode display blinks.
3. Touch the RTN button to change to the
logic mode.
6ZLFKVHOHFWLRQ
1. Select the right and left switch respectively.
(Refer to the description at the previous
page.)
$SSHQGL[! 123