Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Edition R1.0
Welcome
Thank you for purchasing our DVR!
This manual is designed to be a reference tool for the installation and operation of your system.
Here you can find information about this series DVR features and functions, as well as a detailed
menu tree.
Before installation and operation please read the following safeguards and warnings carefully!
Do not let any solid or liquid fall into or infiltrate the DVR.
Please brush printed circuit boards, connectors, fans, machine box and so on regularly. Before
the dust cleaning please switch off the power supply and unplug it.
Do not disassemble or repair the DVR by yourself. Do not replace the components by yourself.
Environment
Please place and use the DVR between 0℃ and 40℃.Avoid direct sunlight. Stay away from heat
source.
Page 1
Directory
1 Production Introduction............................................................................................................................5
1.1 Product overview...........................................................................................................................5
1.2 Main functions...............................................................................................................................5
2 Open-package check and cable connections..........................................................................................7
2.1 Open-package check.....................................................................................................................7
2.2 Hard disk installation.....................................................................................................................7
2.3 Front panel....................................................................................................................................8
2.4 Rear panel.....................................................................................................................................8
2.5 Audio and video input and output connections..............................................................................9
2.5.1 Video input connections......................................................................................................9
2.5.2 Video output connections and options................................................................................9
2.5.3 Audio signal input..............................................................................................................10
2.5.4 Audio signal output............................................................................................................10
2.6 Alarm input and output connections............................................................................................10
2.6.1 Alarm input port specification............................................................................................11
2.6.2 Alarm output port specification..........................................................................................12
2.6.3 Alarm output port relay parameters...................................................................................12
2.7 Speed dome connections............................................................................................................12
3 Basic operation......................................................................................................................................14
3.1 Turn on........................................................................................................................................14
3.2 Turn off.........................................................................................................................................14
3.3 System Login...............................................................................................................................15
3.4 Preview........................................................................................................................................15
3.5 Desktop shortcut menu................................................................................................................16
3.5.1 Main menu.........................................................................................................................16
3.5.2 Playback............................................................................................................................17
3.5.3 Record Mode.....................................................................................................................20
3.5.4 Alarm output......................................................................................................................21
3.5.5 PTZ control........................................................................................................................21
3.5.6 Color setting......................................................................................................................27
3.5.7 Output adjust.....................................................................................................................27
3.5.8 Logout...............................................................................................................................27
3.5.9 Window switch...................................................................................................................28
4 Main menu.............................................................................................................................................29
4.1 Main menu navigation.................................................................................................................29
4.2 Record.........................................................................................................................................31
4.2.1 Record Config...................................................................................................................31
4.2.2 Snapshot Storage.............................................................................................................32
4.2.3 Playback............................................................................................................................33
4.2.4 Backup..............................................................................................................................33
4.3 Alarm............................................................................................................................................35
Page 2
4.3.1 Motion Detect....................................................................................................................35
4.3.2 Video Blind........................................................................................................................37
4.3.3 Video Loss.........................................................................................................................38
4.3.4 Alarm input........................................................................................................................39
4.3.5 Alarm output......................................................................................................................39
4.3.6 Abnormal...........................................................................................................................39
4.4 System.........................................................................................................................................40
4.4.1 General..............................................................................................................................40
4.4.2 Encode..............................................................................................................................41
4.4.3 Network.............................................................................................................................43
4.4.4 NetSevice..........................................................................................................................43
4.4.5 GUI Display.......................................................................................................................50
4.4.6 PTZ....................................................................................................................................51
4.4.7 RS232...............................................................................................................................52
4.4.8 Tour...................................................................................................................................52
4.5 Advanced.....................................................................................................................................53
4.5.1 HDD Manage.....................................................................................................................53
4.5.2 Account.............................................................................................................................53
4.5.3 Online user........................................................................................................................56
4.5.4 Output adjust.....................................................................................................................56
4.5.5 Auto maintain.....................................................................................................................56
4.5.6 Restore..............................................................................................................................57
4.5.7 Upgrade.............................................................................................................................57
4.5.8 Device Info........................................................................................................................58
4.6 Info...............................................................................................................................................58
4.6.1 HDD info............................................................................................................................58
4.6.2 BPS...................................................................................................................................59
4.6.3 Log....................................................................................................................................59
4.6.4 Version..............................................................................................................................60
4.7 Shut down system.......................................................................................................................60
5 FAQ and maintenance...........................................................................................................................61
5.1 FAQ..............................................................................................................................................61
5.2 Maintenance................................................................................................................................66
Appendix 1.Remote controller operation..................................................................................................67
Appendix 2.Mouse operation....................................................................................................................68
Appendix 3.Hard disk capability calculation.............................................................................................69
Appendix 4.Technique parameters...........................................................................................................70
Page 3
Page 4
1 Production Introduction
The series DVR is designed specially for security and defence field which is an outstanding digital
surveillance product. It introduces embedded LINUX operating system which is more stable. It
introduces standard H.264mp video compressed format and G.711A audio compressed format which
insures the high quality image, low error coding ratio and single frame playing. It introduces TCP/IP
network technology which achieves the strong network communication ability and telecommunication
ability.
The series DVR can be used individually or online applied as a part of a safety surveillance
network. With the professional network video surveillance software it achieves the strong network
The series DVR can be applied in the bank, telecom, electric power system, judicial system,
Real-time surveillance
Storage
non-working hard disk dormancy processing which is convenient to radiate heat, reduce power and
Compression
real-time compression by individual hard disk which insures the audio and video signal stable
synchronization
Backup
through SATA interface and USB interface such as USB equipment, removable hard disk and so on
Page 5
Playback
individual real-time video recording as well as searching, playback, network surveillance, recording
multi-playback mode
Net operating
tele-PTZ control
Alarm linkage
multi-route relay alarm output which is convenient for the alarm linkage and light control at the spot
protecting circuits at the alarm input and output interface which protects the main machine from damage
Communication interface
RS485 interface which fulfills the alarm input and PTZ control
Intelligent operating
Page 6
2 Open-package check and cable connections
First, please check whether there is any visible damage to the package appearance. The protective
materials used for the package of the DVR can protect most accidental clashes during transportation.
Then, please open the box and get rid off the plastic protective materials. Check whether there is
At last, please open the machine crust and check the data wire in the front panel, power wire, the
Please check the product type in the front panel whether is accordant with the product type you
order.
The label in the real panel is very important for the after service. Please protect it carefully. When
you contact us for after service, please provide the product type and serial number in the label.
1 disassemble the screw ②disassemble the cover ③fix the screw of hard disk
Page 7
④fix the screw of hard disk ⑤connect the data wire ⑥connect the power wire
(9) Power indicator light (10)Record indicator light (11) Alarm indicator light
Page 8
2.4 Rear panel
(1) audio input (2) video input (3) VGA output (4) switch
(5) alarm input (6) alarm output (7) 12V power output (8) video output
(9) audio input (10) audio output (11) network (12) USB2.0
(13) RS485 (14) power supply
The video input port is BNC connector plug. The demand of input signal is PAL/NTSC BNC(1.0V P-
P ,75Ω).
The video signal must be accorded with the state standard which has the high signal to noise ratio,
low aberration and low interference. The image must be clear and has natural color in the appropriate
brightness.
The vidicon should be installed in the appropriate location where is away from backlighting and low
The ground and power supply of the vidicon and the DVR should be shared and stable.
The video transmission line should adopt high quality coaxial pair which is chosen by the
transmission distance. If the transmission distance is too far, it should adopt shielded twisted pair, video
The video signal line should be away from the electro magnetic Interference and other equipments
Page 9
The signal and shield lines should be firm and connected credible which avoid false and joint
The video output is divided into PAL/NTSC BNC(1.0VP-P,75Ω) and VGA output(selective
configuration).
When replace the monitor by the computer display, there are some issues to notice.
TV is not a credible replacement as a video output. It demands reducing the use time and control
the power supply and the interference introduced by the nearby equipments strictly. The creepage of
The audio signal line should be firm and away from the electro magnetic Interference and
connected credible which avoid false and joint welding and oxidation. The high voltage current should
be avoided especially.
Commonly the output parameter of DVR audio signal is greater than 200mv 1KΩ(BNC) which can
connect the low impedance earphone and active sound box or other audio output equipments through
power amplifier. If the sound box and the tone arm can not be isolated, howling phenomena is often
existed. There are some methods to deal with the above phenomena.
2、 Adjust the sound box volume to be under the threshold that produces the howling phenomena.
3、 Use fitment materials that absorb the sound to reduce reflection of the sound.
4、 Adjust the layout of the sound box and the tone arm.
Page 10
2.6 Alarm input and output connections
1、Alarm input
C. When the alarm is connected with two DVRs or connected with DVR and other equipments, it
2、Alarm output
Alarm output can not be connected with high-power load(no more than 1A).When forming the
output loop it must prevent the big current from relay damage. Use the contact isolator when there is a
high-power load
A. The grounding of the PTZ decoder and DVR must be shared otherwise the common-mode
voltage will lead to the PTZ control failure. The shielded twisted pair is recommended.
B. Avoid the entrance of high voltage. Make the layout reasonably. Take precaution from the
thunder.
C. In the outlying end connect 120Ω resistance paralleled to reduce the inflection and insure the
signal quality.
D. The 485 AB lines of DVR can not connected with other 485 output equipments paralleled.
E. The voltage between the AB lines of the decoder must be less than 5V.
Page 11
(1) alarm input (2) grounding (3) RS232 (4) alarm output (5) RS485
parameter meaning
G grounding
C1、NO1 Alarm output interface(constant open type)
T、R RS232 port
A、B 485communication interface which is connected with the
The grounding and the com port of the alarm sensor are parallel (The alarm sensor is external power
supply) .
The NC port of the alarm sensor must be connected with the DVR alarm input port.
The grounding of the power supply and the alarm sensor must be shared when used in external
power supply.
1 channels alarm output. There is external power supply when using the external alarm equipment.
Please refer to the relay relevant parameters to avoid the overload that damages main machine.
Page 12
2.6.3 Alarm output port relay parameters
Type:JRC-27F
Interface material silver
rating Rating switch capacity 30VDC 2A, 125VAC
temperature
2.7 Speed dome connections
1、Connect the 485 lines of the speed dome with the DVR 485 interface.
Page 13
3 Basic operation
3.1 Turn on
Plug the power supply and turn on the power supply switch. Power supply indicator light shining
indicates turning on the video recorder. After the startup you will hear a beep. The default setting of
video output is multiple-window output mode. If the startup time is within the video setting time, the
timing video recording function will start up automatically. Then the video indicator light of corresponding
Note:1. Make sure that the input voltage corresponds with the switch of the DVR power supply.
Suggest using the UPS to protect the power supply under allowable conditions.
There are two methods to turn off the DVR. Entering [main menu] and choosing [turn off] in the [turn
off the system] option is called soft switch. Pressing the power supply switch is called hard switch.
Illumination:
If the DVR is shut down abnormally, it can automatically backup video and resume previous
Before replacing the hard disk, the power supply switch in the real panel must be turned off.
Before replacing the battery, the setting information must be saved and the power supply
switch in the real panel must be turned off. The DVR uses button battery. The system time must be
checked regularly. If the time is not correct you must replace the battery, we recommend replacing
the battery every year and using the same battery type.
Note: The setting information must be saved before replacing the battery otherwise information
will lose.
Page 14
3.3 System Login
When the DVR boots up, the user must login and the system provides the corresponding functions
with the user purview. There are three user settings. The names are admin, guest and default and
these names have no password. Admin is the super user purview; guest and default’s permissions
are preview and video playback. User admin and guest’s password can be revised, while their
permissions can’t be revised; user default is the default login user whose permission can be revised
Password protection: If the password is continuous wrong three times, the alarm will start. If
the password is continuous wrong five times, the account will be locked. (Through reboot or
For your system security, please modify your password after first login.
3.4 Preview
You can right click mouse to choose the switch between the windows.
The system date, time and channel name are shown in each viewing window. The surveillance video and the
Page 15
3.5 Desktop shortcut menu
In preview mode you can right click mouse to get a desktop shortcut menu. The menu includes:
Page 16
Picture3.3 Main Menu
3.5.2 Playback
There are two methods for you to play the video files in the hard disk.
2、 Main menu>Record->Playback
Note: The hard disk that saves the video files must be set as read-write or read-only state.(4.5.1)
【Listed files】Look up the listed files that accord with the searching criteria.
【File backup】Backup the chosen file. Click the button and operate as followed.
Note: The storage must be installed before the file backup. If the backup is terminated, the
Page 17
Picture 3.5 detect the storage
Detect: Detect the storage connected with the DVR such as hard disk or universal disk.
Erasure: Choose the file to delete and click erasure to delete the file.
Backup: Click backup button and the dialog box is popped up. You can choose the backup file
Start/Pause:Click the play button to start the backup and click the pause button to stop
the backup.
Page 18
Cancel:During backup you can exit the page layout to carry out other functions.
Full screen
Note: Frame by frame playback is only performed in the pause playback state.
Special functions:
Accurate playback:Input time (h/m/s) in the time column and then click play button. The
mouse in the screen to select a section and then left click mouse to realize local zoom. You can right
Page 19
click mouse to exit.
Please check current channel status: “○” means it is not in recording status, “●” means it is in
recording status.
You can use desktop shortcut menu or click [main menu]> [recording function]> [recording set]
to enter the recording control interface.
【Manual】Click the all button and the according channel is recording no matter the channel in any
state.
【Stop】Click the stop button and the according channel stops recording no matter the channel in
any state.
Please check current channel status: “○” means it is not in alarming status, “●” means it is in
alarming status.
You can use desktop shortcut menu or click [main menu]> [alarm function]> [alarm output] to
enter the alarm output interface.
【Manual】Click the all button and the according channel is alarming no matter the channel in any
Page 20
state.
【Stop】Click the stop button and the according channel stops alarming no matter the channel in any
state.
Operation interface is as followed. The functions include: PTZ direction control, step, zoom, focus,
iris, setup operation, patrol between spots, trail patrol, boundary scan, assistant switch, light switch,
Note1. Decoder A(B)line connects with DVR A(B)line. The connection is right.
2. Click [main menu] >[system configuration] >[PTZ setup] to set the PTZ parameters.
panel is supportive )
【High speed PTZ】Full-screen show channel image. Left press mouse and control PTZ to rotate
orientation. Left press mouse and then rotate the mouse to adjust the zoom multiple of the camera.
Special functions:
Page 21
1、Preset
Set a location for the preset, calls the preset points, PTZ automatically turns to the setting
position
1)Preset option
Step1: in Picture 3.10, click the Direction button will turn into preset position , click the Settings
Step 2: click the Preset button , then write the preset points in the input blank,
Step 3: click Settings button, return the Picture 3.10 Complete setup, that is the preset points and
Clear Preset:Input preset points, click Remove button, remove the preset。
In Picture 3.10, click Page Shift button, enter PTZ control interface as shown in Picture 3.12. In
the input blank, write the preset points, then click Preset button, PTZ turn to the corresponding
preset point.
Page 22
Value input
blank
Multiple preset points connected cruise lines, call cruise between points, the PTZ run around
on the line
Step1: In Picture 3.10, the Direction key will turn PTZ to designated location , click Settings
Step 2: click Cruise buttons, the write proper value into the Cruise Line and Preset Points
blank,then click Add Preset Points button, complete setting (also can add and delete cruise line
Step 3: repeat step1 and step2 , until set out all the preset designated cruise lines。
Remove Preset : Please input preset value in the blank, click Remove Preset button, then
Remove Cruise Line:Input the number of cruise line, click Remove Cruise Lines button, then
Page 23
Preset Points Blank
Cruise Button
In Picture 3.10, click Page Shift button, enter PTZ control menu as shown in Picture 3.12. Please
input the number of cruise in the value blank, then click Cruise between Points button, PTZ begins to
3、Scan
1)Scan setup
Step1:In Picture 3.10, click Setup button ,enter Picture 3.14;
Step2:Click Scan button,the input proper value in the scan value blank;
Step3 : Click Start button, enter Picture3.10 , here you can set the following items:
Step4:Click End button to complete setup。Click the right button of the mouse to exit.
Scan Button
2)Scan Calls
Page 24
In Picture 3.10, click Page Shift button, then enter PTZ control menu as shown in Picture 3.12.
Please input the number of scan in the value blank , then click Scan button,PTZ begins to work on
4、Boundary Scan
Step1 : In Picture 3.10, click Direction button to turn the PTZ to preset direction, then click
Setup button enter Picture 3.15, select the left boundary, return to Picture 3.10;
Step2 : Please click direction arrows to adjust PTZ direction, click Setup button enter
Step3: Complete setup, that is the position of left and right boundary
In Picture 3.10, click Page Shift button, then enter PTZ control menu as shown in Picture 3.12.
Please input the number of scan in the value blank , then click Scan button,PTZ begins to work on
5、Horizontal Rotating
Click Horizontally Rotating button, PTZ begins to rotate horizontally (relative to the original position
6、Rotate
7、Reset
Page 25
8、Page Shift
In Picture 3.12, click Page Shift button into Picture3.16, setting auxiliary function. Auxiliary
【Intuitive Auxiliary Operation】choose auxiliary equipment, select Open or Close button, switch
control;
agreement;
【Page Shift】In Picture 3.16,click Page Shift button enter the Picture 3.17 PTZ Main Menu ,
Set the selective image parameters (current channel for single window display and cursor place for
multi-window display). You can use the desktop shortcut menu and enter the interface. The image
parameters include: tonality, brightness, contrast, saturation. You can set different parameters at
Page 26
3.5.7 Output Adjust
Adjust TV output area parameters. You can use the desktop shortcut menu or enter [main menu]>
3.5.8 Logout
Logout, shut down the system or reboot up. You can use the desktop shortcut menu or enter [main
menu].
When press the shut down button, there is schedule hint. After three seconds, the
Page 27
4 Main menu
Config Set the recording configuration, recording type, recording time section
Record playback Set recording look-up, recording play, video file storage
Motion Set motion detect alarm channel, sensitivity, area, linkage parameters:
detection defending time section, alarm output, screen hint, recording, PTZ, patrol
Video Set camera mask alarm channel, sensitivity, linkage parameters:
blind defending time section, alarm output, screen hint, recording, PTZ, patrol
Video Set video loss alarm channel, linkage parameters: defending time
Alarm
loss section, alarm output, screen hint, recording, PTZ, patrol
Alarm Set alarm input channel, equipment type, linkage parameters:
input defending time section, alarm output, screen hint, recording, PTZ, patrol
System General Set system time, data format, language, hard disk full time operation,
configuratio configuration machine number, video format, output mode, summertime, stay time
Set main(assistant)coding parameter: code mode, resolving ability,
n
Encode
frame rate, code stream control, image quality type, code stream value,
configuration
frame between value, video/audio enable
Network Set basic network parameters, DHCP and DNS parameters, network
Set channel name, preview hint icon state, transparency, cover area,
GUI display
time title, channel time fold
PTZ Set channel, PTZ protocol, address, baud rate, date bit, stop bit, check
configuration
Page 28
Serial port
Configuration Set serial port function, baud rate, date bit, stop bit, check
(RS232)
Hard disk Set appointed hard disk as read-write disc, read-only disc or redundant
Restore alarm setup, network setup, network service, preview playback, serial
4.2 Record
Set the recording parameters in the surveillance channel. The system is set 24 hours consecutive
recording in the first startup. You can enter [main menu]> [recording function]> [recording setup] to set.
Page 29
Picture 4.1 Record Config
【Channel】Choose the corresponding channel number to set the channel. Choose the all option to
【 Redundancy 】 Choose the redundancy function option to implement the file double backup
function. Double backup is writing the video files in two hard disks. When you do the double
backup, make sure that there are two hard disks installed. One is read-write disk and the other is
【Length】Set the time length of each video file. 60minutes is default value.
【PreRecord】Record 1-30 seconds before the action. (time length is decided by the code stream)
Schedule:Record according to the set video type (common, detection and alarm)and time
section.
Manual:Click the button and the according channel is recording no matter the channel in
any state.
Stop:Click the stop button and the according channel stops recording no matter the
【Period】Set the time section of common recording, The recording will start only in the set range.
Regular:Perform the regular recording in the set time section. The video file type is “R”.
Detect:Trigger the “motion detect”, “camera mask” or “video loss” signal. When above
alarm is set as opening recording, the “detection recording” state is on. The video
Page 30
file type is “M”.
Alarm:Trigger the external alarm signal in the set time section. When above alarm is set
as opening recording, the “detection recording” state is on. The video file type is
“A”.
Setup snapshot parameters for different channels.At first time it's set for 24hours snapshot
Picture 4.2
Manual:No matter what the present channel is in a state,once choose "manual" button,it
Stop:No matter what the present channel is in a state,once choose "stop" button,it will
【Period】Set normal record period,it only startup Snapshot Storage at set period.
Page 31
【Type】Three types:regular,detect and alarm
Detect:snapshot at set period when motion detect,video blind and video loss which are
Alarm:snapshot at set period when alarm in which is preset for snapshot enable.
4.2.3 Playback
4.2.4 Backup
You can backup the video files to external storage through setup.
Note:The storage must be installed before the file backup. If the backup is terminated, the
【Detect】Detect the storage connected with the DVR such as hard disk or universal disk.
【Erase】Choose the file to delete and click erasure to delete the file.
【Backup】Click backup button and the dialog box is popped up. You can choose the backup file
Page 32
Picture 4.4 File Backup
Start/pause:Click the play button to start the backup and click the pause button to stop the
backup.
Cancel:During backup you can exit the page layout to carry out other functions.
Alarm functions include: motion detect,video blind, video loss, alarm input and alarm output.
When system detects the motion signal that reaches the set sensitivity, the motion detect alarm is
Page 33
Picture 4.4 Motion Detect
【 Region 】 Click setup and enter the set area. The area is divided into PAL22X18. Green block
means the current cursor area. Yellow block means the dynamic detect defensive area. Black
block means the unfenced area. You can set the area as followed, Drag the mouse and draw the
area.
【Period】Trigger the motion detect signal in the set time section. You can set according to week or
set uniformly. Each day is divided into four time sections.■ means the set valid.
Page 34
Picture 4.6 set the time section
【Interval】Only one alarm signal is turned on even there are several motion detect signals in the set
interval.
【Alarm output】Start the external equipment of corresponding linkage alarm when the motion detect
【Delay】Delay a few moments and stop when the alarm state is turned off. The range is 10~300
seconds.
【 Record channel 】 Choose the recording channel (multiple option supportive). Trigger the video
Note:Set in the [recording setup] and perform the linkage recording. Start detecting video files
【Tour】■ means that the selective channel is single window alternate patrol preview. The interval is
snapshot signal.
>Record config,
【PTZ Activation】Set the PTZ activation when the alarm is turned on.
Note:PTZ activation is set in the [shortcut menu] >[ PTZ control]. Set the patrol between spots,
Page 35
Picture 4.8 PTZ Activation
【Show message】Pop the alarm information dialog box in the local host computer screen.
【Send EMAIL】■ means sending an email to user when the alarm is turned on.
When the video image is influenced by the environment such as bad brightness or reaching the set
sensitivy parameter, the camera mask function is turned on and the linkage function is turned on.
Page 36
4.3.3 Video Loss
When the equipment can not obtain the channel video signal, the video loss alarm is turned on and
When the equipment obtains the external alarm signal, the alarm function is turned on.
Page 37
Set method: refer to chapter 4.3.1. Motion detect
4.3.6 Abnormal
Analysing and inspecting current software and hardware of the device: When some abnormal
events happen,the device will make a relative answer such as show message and buzzer.
【Show message】 Automatically alarm cue dialog box come out of the main screen
【Buzzer】 Device will have two long nosie “di di” while alarm is happening
Page 38
4.4.1 General
【Language】English,French,Portugueses,Russian,Italian,S-Chinese,
T-Chinese,Spanish,Thai,Greek,Japanese,German,Polish.
【HDD full】Choose stop record: Stop recording when the hard disk is full.
Choose overwrite: Cover the earliest recording files and continue recording when the hard
disk is full.
【 DVR No. 】 Only when the address button in the remote controller and the corresponding DVR
【DST】Choose the summer time option and pop the dialog box as followed.
Page 39
Picture 4.14 DST (week)
Set the video/audio code parameter: video file, remote monitoring and so on. Set every
independent channel’s coding parameter in the left part, and set the combine encode parameter in the
right part.
Note: Combine encode introduces video compression technique which combines and compresses
Page 40
Picture 4.16 Encode setup
【Bit Rate Type】You can choose limited code stream or variable code stream. When you choose
the variable code stream there are six image quality options.
【Bit Rate】Set the code stream value to modify the image quality. The larger code stream value the
D1(1000~1500kbps),CIF(384~1500kbps), QCIF(64~512kbps)
【 Video/Audio 】 When the icons are all in reverse displayed, the video file is video and audio
multiplex stream.
Combine Enable
【Combine Enable】When the icons are all in reverse displayed, opening combination coding functions.
【 Mode 】 multi-channel playback is used in all channels playback simultaneously, and the
Page 41
4.4.3 Network setup
Picture4.17 Network
【Net Card】You can choose cable network card or wireless network card.
【DNS setup】Domain Name Server. It translates the domain name into IP address. The IP address
is offered by network provider. The address must be set and reboot then it works.
【HS Download】
【Transfer Policy】There are three strategies: self-adaption, image quality precedence and fluency
precedence. The code stream will adjust according to the setup. Self-adaption is the tradeoff between
the image quality precedence and fluency precedence. Fluency precedence and self-adaption are
valid only when the assistant code stream is turned on. Otherwise image quality precedence is valid.
4.4.4 NetService
Choose the network service option and click the set button to configure the advanced network
Page 42
functions or double click the service button to configure the parameters.
【PPPoE setup】
Picture4.19 PPPOE
Input the user name and password that ISP (Internet service provider)provides. After saving it
reboot up your system. Then the DVR will build a network connection based on PPPoE. The IP address
will change into dynamic IP address after above operation is well done.
Operation:After PPPoE dialing successfully look up the IP address in the [IP address] and obtain
the current IP address. Then use this IP address to visit the DVR through user port.
【NTP setup】
Page 43
Picture 4.20 NTP
Port:Default: 123. You can set the port according to NTP server.
Time zone:London GMT+0 Berlin GMT +1 Cairo GMT +2 Moscow GMT +3 New Delhi GMT +5
Bangkok GMT +7 Hongkong Beijing GMT +8 Tokyo GMT +9 Sydney GMT +10 Hawaii GMT-10
Alaska GMT-9 Pacific time GMT-8 American mountain time GMT-7 American mid time GMT-6
American eastern time GMT-5 Atlantic time GMT-4 Brazil GMT-3 Atlantic mid time GMT-2.
Update Period:The same with the NTP server check interval. Default: 10minutes.
【EMAIL setup】
If the alarm is turned on or the alarm linkage photos are taken, send an email about the alarm
Page 44
Picture 4.21 EMAIL
SMTP server:Email server address. It could be an IP address or domain name. Domain name can
Receiver:Send the email to appointed receivers when the alarm is turned on. You can set three
receivers at most.
When choosing the white list, only the listed IP address can connect the DVR. The 64 IP addressed
When choosing the black list, the listed IP address can not connect the DVR. The 64 IP addressed
Note : When the same IP address is in the white and black list at the same time, the black list
precedence is higher.
Page 45
【DDNS】
【FTP setup】FTP is available only when alarm happens,or alarm activates record and snapshot,it will
Page 46
【Port】Domain Port of FTP,default 21
【Password】Password of user
【Max File Length】Max length for upload files at every packed,default 128M
【Wireless Config】ADSL through 3G net card,use CMS to visit and config the device
To visit the device by mobile,pls make a router mapping of this port and use CMS to monitor and
operate it by protocol.
Page 47
Picture 4.26 Mobile Monitor Setup
【Port】 It’s a port of mobile monitoring which you need to make a router mapping of if want to visit it
by mobile
【UPNP】 UPNP protocol can auto port forwarding on router,make sure UPNP is running on router
Picture 4.27
【HTTP】Route will automatically distribute HTTP port for the device,when IE viewing,it need this
port(eg. 60.12.9.26:66)
【TCP】Router will automatically distribute TCP port for the device,when monitoring via CMS,it need
this port.
【MobilePort】Router will automatically distribute Mobile Port for the device,when mobile monitor,it
Page 48
4.4.5 GUI Display
Configure the video output parameters including the front output mode and code output mode.
Front output : In the local preview mode include: channel title, time display, channel title, record
Code output :In the network surveillance and video file mode include: channel title, time display,
channel title, record status, alarm status,bitrate info, transparency and region cover.
【Channel Title】Click the channel name modify button and enter the channel name menu. Modify
the channel name. The 16 Chinese characters and 25 letters are supportive.
【Time Display 】means the selective state. Display the system data and time in the surveillance
window.
【Channel Title】means the selective state. Display the system channel number in the surveillance
window.
【Record Status】means the selective state. Display the system recording status in the surveillance
window.
【 Alarm Status 】 means the selective state. Display the system alarm status in the surveillance
window.
【Bitrate info】means the selective state. The ninth window displays the code stream information in
Page 49
【Channel】Choose the set code output channel number.
【Region Cover】means the selective state. Click the cover area button and enter the corresponding
channel window. You can cover the arbitrary using mouse. (Black region is for
output)
【 Address 】 Set as the corresponding dome address. Default: 1. ( Note : The address must be
【 Baudrate 】 Choose the corresponding dome baud rate length. You can control the PTZ and
【Parity】Include odd check, even check, sign check, blank check. Default: void.
Page 50
Picture 4.30 RS232 setup
【Serial Port Function】Common serial port is used to debug and update program or set up specific
serial port.
Set the patrol display. means that the tour mode is turned on. You can choose the single window,
four windows, nine windows, sixteen windows patrol display or single display.
Page 51
Picture 4.31 tour setup
【interval】Set the patrol switch interval. The set range is 5-120 seconds.
4.5 Advanced
Configure and manage the hard disk. The menu displays current hard disk information: hard disk
number, input port, type, status and overall capability. The operation include: setup the write-read disk,
read-only disk, redundant disk, hard disk format, resume default. Choose the hard disk and click the
Read-only Disk:The equipment can read data but can not write data.
Page 52
Picture4.32 HDD Manage
4.5.2 Account
Note:1. The character length is 8 bytes at most for the following user and user team name. The blank
ahead or behind the character string is invalid.The middle blank in the character string is valid.
2. There is no limit in the user and user group. You can add or delete the user group according to
user definition. The factory setup include: user\admin. You can set the team as you wish. The user
3. The user management include: group/ user. The group and user name can not be the same.
Page 53
Picture 4.33 Account
【Modify Password】Modify the user password. You can set 1-6 bit password. The blank ahead or
behind the char string is invalid. The middle blank in the char string is valid.
Note : The user who possess the user control purview can modify his/her own or other
users password
【Add user】Add a user in the team and set the user purview. Enter the menu interface and input the
user name and password. Choose the team and choose whether cover using the user. Cover using
means that the account can be used by multiple users at the same time.
Page 54
Once choose the team the user purview is the subclass of the team.
We recommend that the common user’s purview is lower than the advanced user.
【Add Group】Add a user team and set the purview. There are 36 different purviews: shut down the
equipment, real time surveillance, playback, recording setup, video file backup and so on.
【Delete User】Delete the current user. Choose the user and click delete user button.
【Delete Group】Delete the current group. Choose the group and click delete group button.
Page 55
Picture 4.37 Delete Group
Look up the network user information in the local DVR. You can choose the network user and cut
4.5.4 TV adjust
Page 56
4.5.5 Auto Maintain
The user can set the auto reboot time and auto file deleting time limit.
4.5.6 Restore
The system restore to the default setup. You can choose the items according to the menu.
Page 57
4.5.7 Upgrade
4.6 Info
Display the hard disk state: hard disk type, overall capability, residual capability, the recording time
and so on.
Page 58
Picture 4.43 HDD Info
Clue:○ means that the hard disk is normal. X means that the hard disk is broken-down.- means that
there is no hard disk. If the user need to change the damaged hard disk, you must shut down the DVR
and take up all the damaged hard disks,then install a new one.
* behind serial number means the current working disk such as 1*. If the corresponding disk is
4.6.2 BPS
Display the code stream(Kb/S)and hard disk capability (MB/H)in real time. It displays as the
Page 59
Picture 4.44 BPS
4.6.3 LOG
Log information include: system operation, configuration operation, data management, alarm
affair, recording operation, user management, file management and so on. Set the time section to look
up and click the look up button. The log information will display as a list. (one page is 128 items) Press
Page up or Page down button to look up and press delete button to clear all the log information.
Page 60
Picture4.45 LOG
4.6.4 Version
Display the basic information such as hardware information, software edition, issue data and so on.
Page 61
5 FAQ and maintenance
5.1 FAQ
If the problems are not listed, please contact the local service or call the HQ service. We are willing
5 The hard disk is damaged or the hard disk lines are broken.
2、 The DVR reboots automatically or stops working after boot up a few minutes.
2 The hard disk is damaged or the hard disk lines are broken.
5 Bad heat radiator or too much dust or bad running circumstance for the DVR.
4、 There are no video outputs in single channel, multiple channels and all channels.
Page 62
1 The program is not matched. Please update the program.
5、 Real-time image problems such as the image color or the brightness distortion.
1 When using the BNC output, the option between the N mode or PAL mode is wrong and
3 The video transmission distance is too far or the loss of the video transmission line is too
large.
Page 63
4 The hardware of the DVR is damaged.
9、 There is audio signal in the surveillance window but mo audio signal in the playback
state.
1 Setting is wrong..
2 The setting, connection or the installation of the PTZ decoder is not correct.
5 The protocols of the PTZ decoder and the DVR are not matched.
6 The address of the PTZ decoder and the DVR are not matched.
7 When multiple decoders are connected, the far port of the PTZ decoder line A(B) must
connect a 120 resistance to reduce the reflection otherwise the PTZ control is not
stable.
Page 64
higher Version or installing the software for low edition.
3 The version is not exceeded dx8.1. Update the display card driver.
14、 The image is not clear or there is no image in network preview state or video file
playback state.
6 The real-time image of the hard disk recording machine itself is not clear.
2 IP address is conflicted.
16、 There is something wrong with the USB backup or writing a CD.
1 The rewritable machine and the hard disk are shared the same data lines.
Page 65
2 The address is not correct.
3 When multiple transformers are connected, the power supply is not large enough. Please
4 There are some problems for specific program edition, Please update the program.
2 The remote control distance is too far or the angle is too large.
4 The remote controller or the front panel of the recording machine is damaged.
1 Front vidicon quality is bad. The lens is too dirty. The vidicon is in backlighting installation.
Page 66
4 The DivX503Bundle.exe and ffdshow-2004 1012 .exe files must be installed in the
windows xp system.
23、 I can not remember the advanced code or network code in the local menu operation.
Please contact the local service or call the HQ service. We will offer the service according the
5.2 Maintenance
1 Please brush printed circuit boards, connectors, fans, machine box and so on regularly.
2 Please keep the grounding well done to prevent the video or audio signal interfered and
3 Do not pull out the video signal line or RS-232 port or RS-485 port with the power on.
4 Do not use the TV in the local video output port(VOUT) of DVR. It will damage the video
5 Do not turn off the switch directly. Please use the turn-off function in the menu or press the
turn-off button in the panel (3 seconds or longer) to protect the hard disk.
Page 67
Appendix 1.Remote controller operation
number
1 Multi-window Same function as Multi-window button in the front
button panel
2 Numeric button Code input/number input/channel switch
3 【Esc】 Same function as【Esc】button in the front panel
4 Direction button Same function as direction button in the front panel
5 Record control Control the record
6 Record mode Same function as “Record mode”
7 ADD Input the number of DVR to control it
8 FN Assistant function
Page 68
Appendix 2.Mouse operation
Operation Function
video
Page 69
Appendix 3.Hard disk capability calculation
Make sure the hard disk installed to the DVR for the first time. Pay attention to the IDE hard disk
lines connection.
There is no limit for recording machine. We recommend 120G~250G size to keep better
stability.
overall capability(M)
Recording time(hour)=
The DVR introduces the H.264 compression technology. Its dynamic range is very large so the
hard disk capability calculation is based on the estimation values of each channel creating files in
an hour.
Example:
For one piece 500G HDD,real time CIF for recording,it will keep recording for about 25 days.HDD
spaces per channel is 200M/H,if 4channels real time CIF at 24hours recording uninterrupted,it can
last:500G/(200M/H*24H*4ch)=26 days
Page 70
Appendix 4.Technique parameters
network operation
Operation interface 16 bit true color graphical menu interface, mouse operation
supportive
Interface
display 1/4image display 1/4/8/9 image display 1/4/8/9/16 image
display
quality
quality
Video
Video compression H.264 mp
50/60fps D1
Page 71
Playback Any channels playback, multiple channels playback
And
Search mode Time searching, calendar searching, affair searching, channel
Playback
searching, information searching
Working 0℃~+55℃
temperature
Size 310(width)x215(depth)x45(height)mm
Installation Desktop
Page 72