Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
quick-start guide 1 Turn power off at circuit breaker! 2 Remove existing switch from wall 3 Remove side sections (if necessary) 4 Connect the dimmer 6 Attach the wallplate
CAUTION
Use only with permanently installed fixtures
with dimmable LED, halogen, MLV halogen, or
Optional Neutral incandescent lamps. To avoid overheating and
In-wall dimmer PRO Remove the wallplate from switch. 5 Attach the adapter to the dimmer using the
possible damage to other equipment, do not use
screws provided and snap on the wallplate.
OFF
Welcome—and thank you for purchasing a CasétaR 4 to control receptacles, motor-driven appliances.
Wireless in-wall dimmer PRO. In order to control your
lights from an app or remote, you’ll need to replace an 1 3 Codes
existing switch with a CasétaR Wireless in-wall dimmer Install in accordance with all national and local
PRO. WARNING: SHOCK HAZARD 1 electrical codes.
May result in serious injury or death. Turn off 2
Bend back
Before you install the dimmer, please watch the power at circuit breaker or fuse before installing. and forth. Grounding
installation video at 2 1 When no “grounding means” exist in wallbox, the
www.casetawireless.com/support Ground National Electrical Code (NEC®) allows a control to
be installed as a replacement if 1) a nonmetallic,
We hope you enjoy the convenience of CasétaR Wireless!
Remove the switch and pull it away from the wall. Do not remove outside side sections 1 Connect the bare copper (or green) “ground” wire noncombustible faceplate is used with nonmetallic
Double your warranty on dimmers at the end of gang. from the wallbox to the green wire on the dimmer
2 attachment screws or 2) the circuit is protected by a
Love CasétaR Wireless dimmers? Have ideas using a wire connector. 3 ground fault circuit interrupter (GFCI). When installing
for making them better? Tell us what you think a control according to these methods, cap or remove
‘snap’ green wire before screwing control into wallbox.
and we’ll extend your warranty by 1 year. 3 2 Connect the load wire from the wallbox to the red
www.casetawireless.com/register wire on the dimmer using a wire connector.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
3 Connect the hot wire from the wallbox to the black license-exempt RSS standard(s). Operation is subject to the following two
wire on the dimmer using a wire connector. conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
4 4 If available, connect the neutral wire from the wallbox Inc. could void the user’s authority to operate this equipment.
Contents supplied Each dimmer Dimmer at middle has all to the white wire on the dimmer. If neutral is not
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
available, cap the white wire with a wire connector. are designed to provide reasonable protection against harmful interference
In-wall dimmer PRO Disconnect all three wires* from the switch. has inside side side sections removed. in a residential installation. This equipment generates, uses and can radiate
(PD-10NXD) sections removed. Neutral required for: MLV loads, LED drivers, PHPM- radio frequency energy and, if not installed and used in accordance with
5 the instructions, may cause harmful interference to radio communications.
PA, PHPM-3F, GRX-TVI. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
Important Note: 3-Way 6 Important note: 5 Cap the blue wire with a wire connector. (The blue (If you installed the dimmer next to other dimmers
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
wire is only used for a 3-way installation with a or switches, you’ll need to install a wallplate with the more of the following measures:
Removing side sections reduces the dimmer’s —Reorient or relocate the receiving antenna.
If you have more than one switch controlling the mechanical toggle switch. See correct size/number of openings to accommodate all
maximum wattage rating. See the chart below —Increase the separation between the equipment and receiver.
light, this is called a 3-way installation. You will need for maximum wattage information. Casetawireless.com/3-way for details.) the devices.) —Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
to buy PJ2-WALL-WH-L01. —Consult the dealer or an experienced radio/TV technician for help.
Wire connectors Screws Ground Maximum* wattage derating chart
Switch 1 Switch 2 7 (120 V~ 50/60 Hz)
x5 x2
Side sections
removed None 1 side 2 sides 5 Mount the dimmer
7 Turn power on at circuit breaker
ON
Flat-head screwdriver Pliers Incandescent & www.casetawireless.com/warranty
1000 W 800 W 600 W
Halogen
MLV Halogen 1000 VA 800 VA 600 VA 1
Phillips-head screwdriver Ground
* If your switch has more than 3 wires attached, see * For maximum wattage information when
Please visit www.casetawireless.com/3way for mixing light bulb types see
“Installing CasétaR Wireless in a 3-way switch application”
more details. www.casetawireless.com/ganging
video at www.casetawireless.com/3way
P/N 0301778 REV A 2
Works with compatible Using your CasétaR Wireless kit (sold separately) Using your controls Troubleshooting
Symptoms Probable cause and action
energy efficient dimmable Light does not • Light bulb(s) burned out.
light bulbs: With a smartphone or tablet (Bridge required, sold separately) Without a smartphone or tablet (Bridge not required) turn on or In-wall • Breaker is OFF or tripped.
dimmer PRO
The CasétaR Wireless dimmer can be controlled from a smartphone • Light not properly installed.
LED*—up to 250 W when used with the LutronR Smart BridgeT. Pairing the dimmer and Changing the favorite light level LEDs do not light
up. • Wiring error.
If you are using the dimmer and remote control with the LutronR Pico® remote control on the Pico® remote control On • FASSTM switch on the dimmer is
Smart BridgeT follow the instructions below.
Lutron (sold separately) in the Off position.
Incandescent / Halogen—up to 1000 W Note: If you are using the dimmer and remote control with
another manufacturer’s bridge, please refer to that manufacturer’s
1 Press and hold “off” button on dimmer Brighter (with raised icon)
Darker
Light does not
respond to Pico®
• The dimmer failed to pair with
Pico® remote control; see
instructions for set-up. You can use the round “favorite” remote control. Pairing the dimmer and Pico®
LutronR Smart BridgeT button on the Pico® remote Off remote control.
LutronR app
Hold for 6 seconds control to recall a favorite light Favorite • The dimmer is already at the
MLV Halogen—up to 1000 VA FASS™
until LEDs start level. We’ve set it to 50%, but you light level the Pico® remote
3 Press
Use theand hold® app
Lutron “off”tobutton ALL remaining steps
on remote
complete
Device Ratings Lutron, Lutron, Caséta, and Pico are registered trademarks and FASS,
In-wall dimmer PRO , and Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC
nortuL
Add devices Control Schedule Connect PD-10NXD is a registered trademark of the National Fire Protection Association,
• PicoR remotes three ways your lights while away Quincy, Massachusetts. Google and the Google logo are registered
120 V~ 50/60 Hz trademarks of Google Inc., used with permission.
Lutron Electronics Co., Inc. • Dimmers
7200 Suter Road For advanced features, tips for using CasétaR Wireless dimmers with LEDs, the complete CasétaR Wireless product line, © 2015 Lutron Electronics Co., Inc
Coopersburg, PA 18036-1299, U.S.A.
• Shades and more, please visit www.casetawireless.com/features P/N 0301778 REV A
®
Wireless Cómo instalar el atenuador Instalación de luces con un interruptor de pared (unipolar)
guía de inicio rápido 1 Corte la corriente del cortacircuitos 2 Retire el interruptor actual de la pared 3 Retire las secciones laterales
(en caso de ser necesario) 4 Conecte el atenuador 6 Coloque la placa de pared
PRECAUCIÓN
Utilice sólo en luminarias instaladas de forma
permanente con LED regulable, halógenos, BVM
Atenuador de luz de pared PRO Retire la placa de pared del interruptor. Neutro Opcional Conecte el adaptador al atenuador con los tornillos halógeno, o lámparas incandescentes. Para evitar
APAGADO
5 suministrados y encájelo en la placa de pared. el sobrecalentamiento y posibles daños a otros
Lea antes de instalar. equipos, no lo use para controlar receptáculos,
Bienvenido, y gracias por comprar el atenuador de luz 4 electrodomésticos con motor.
de pared PRO CasétaR Wireless. Para controlar sus luces
1
desde una aplicación o un control remoto, deberá reemplazar 3 Códigos
un interruptor existente por un atenuador de luz de pared ADVERTENCIA: RIESGO DE 1 Instale de acuerdo con todos los códigos eléctricos
PRO CasétaR Wireless. DESCARGA ELÉCTRICA. Doble hacia atrás 2 nacionales y locales.
Antes de instalar el atenuador, vea el video de Puede resultar en lesiones graves o la muerte. y hacia delante.
instalación en www.casetawireless.com/support Corte la corriente del cortacircuitos o fusible 2 Conexión a tierra
antes de instalar. 1
¡Esperamos que disfrute la comodidad de Cuando no exista ningún medio de conexión a
CasétaR Wireless! No quite las secciones laterales externas Tierra tierra en la caja de pared, el NEC® (Código Eléctrico
Retire el interruptor y aléjelo de la pared. de los atenuadores al final de la conexión. Nacional) permite la instalación de un control como
1 Conecte el cable a tierra de cobre sin protección
Doble su garantía (o verde) desde la caja de pared al cable verde del
2 reemplazo si 1) se usa una placa frontal incombustible
¿Le encantan los atenuadores CasétaR Wireless? atenuador utilizando un conector de cable. 3 que no sea metálica con tornillos de sujeción no
¿Tiene alguna idea para mejorarlos? Cuéntenos su metálicos o 2) el circuito está protegido por un GFCI
2 Conecte el cable de carga de la caja de pared al cable (interruptor de circuito por falla a tierra). Al instalar un
opinión y extenderemos la garantía por 1 año. 3
www.casetawireless.com/register rojo del atenuador utilizando un conector de cable. control de acuerdo con estos métodos, tape o retire
3 Conecte el cable vivo de la caja de pared al cable el cable verde antes de atornillar el control a la caja de
negro del atenuador utilizando un conector de cable. pared.
4 Si está disponible, conecte el cable neutro de la caja
Información de la FCC/IC
de pared al cable blanco del atenuador. Si neutral no Este dispositivo cumple con la parte 15 de las reglas de la FFC (Comisión
4
Cada atenuador tiene El atenuador del medio está disponible, tape el cable blanco con un conector
Contenido suministrado las secciones laterales tiene todas las secciones de cable.
Federal de Comunicaciones) y con las normas RSS de IC (Industry Canada)
para dispositivos exentos de licencia. La operación está sujeta a las dos
condiciones siguientes: (1) Este dispositivo no debe causar interferencia
Atenuador de luz de pared PRO Desconecte los tres cables* del interruptor. internas quitadas. laterales quitadas. perjudicial y (2) este dispositivo debe aceptar cualquier interferencia recibida,
Neutro es necesario para: Cargas BVM, controladores incluyendo las que pueden causar una operación indeseada. Cualquier cambio
(PD-10NXD) 5 de LED, PHPM-PA, PHPM-3F, GRX-TVI. o modificación sin la aprobación explícita de Lutron Electronics Co., Inc. puede
anular la autorización del usuario para operar el equipo.
5 Tape el cable azul con un conector de cable. (El cable Nota: Este equipo ha sido probado y se comprobó que cumple con los límites
6
Nota importante: azul sólo se utiliza para la instalación de 3 vías con un (Si instaló el atenuador al lado de otros atenuadores
para dispositivos digitales de Clase B, de acuerdo con la Parte 15 de las
Reglas de la FCC. Estos límites se han diseñado para proveer una protección
Nota importante: 3 Vías Cuando retira las secciones laterales, se reduce interruptor de palanca mecánica. Ver Casetawireless. o interruptores, debe instalar una placa de pared que
razonable contra interferencias dañinas en una instalación residencial. Este
equipo genera, usa y puede emitir energía de radiofrecuencia y si no se instala
el vataje de régimen máximo. Consulte el cuadro com/3-way para más detalles. tenga la cantidad correcta de orificios y del tamaño y utiliza de acuerdo con las instrucciones, puede causar interferencia dañina en
Si tiene más de un interruptor controlando la luz,
a continuación para obtener la información de correcto para instalar todos los dispositivos.)
las comunicaciones de radio. Sin embargo, no hay garantía de que no ocurrirá
esto se llama una instalación de 3 vías. Usted interferencia en una instalación determinada. Si este equipo causa interferencia
vataje máximo. dañina en la recepción de la radio o la televisión, que se puede determinar
tendrá que comprar PJ2-WALL-WH-L01. Tierra encendiendo y apagando el equipo, el usuario puede tratar de corregir la
Conectores de cables Tornillos Cuadro de reducción de vataje máximo* interferencia mediante uno o más de los siguientes procedimientos:
7 (120 V~ 50/60 Hz)
7
—Cambiar la orientación o ubicación de la antena receptora.
x5 x2
Interruptor 1 Interruptor 2
Secciones
laterales quitadas
2
Ninguna 1 lateral laterales
5 Coloque el atenuador
Encienda la corriente
del cortacircuitos
—Aumentar la separación entre el equipo y el receptor.
—Conectar el equipo a un receptáculo que esté en un circuito diferente al del
receptor.
—Consultar al distribuidor o a un técnico experimentado en radio/TV para
LED 250 W 250 W 250 W Use los tornillos proporcionados. obtener ayuda.
ENCENDIDO
Herramientas que necesitará o*
Destornillador de cabeza plana Alicates Incandescente
1 000 W 800 W 600 W Garantía
y halógena 1 Para obtener información sobre la garantía, visite
Tierra BVM halógena 1 000 VA 800 VA 600 VA www.casetawireless.com/warranty
Destornillador Phillips
*Si su interruptor tiene más de 3 cables, consulte
el video “Installing CasétaR Wireless in a 3-way * Para obtener información del vataje máximo al
Por favor visite www.casetawireless.com/3way switch application” (Cómo instalar CasétaR Wireless combinar tipos de focos de luz, consulte
para más detalles. en una aplicación de interruptor de 3 vías) www.casetawireless.com/ganging 2
a www.casetawireless.com/3way
P/N 0301778 REV A
Añada dispositivos Controle Programe Conecte Atenuador de luz de pared PRO Smart Bridge son marcas comerciales de Lutron Electronics Co., Inc.
NEC es una marca registrada de National Fire Protection Association,
• Controles de tres sus luces a larga PD-10NXD
Quincy, Massachusetts. Google y el logotipo de Google son marcas
remotos Pico® maneras distancia 120 V~ 50/60 Hz registradas de Google, Inc., utilizadas con autorización.
Lutron Electronics Co., Inc. • Atenuadores Para ver características avanzadas, consejos para usar los atenuadores CasétaR Wireless con luces LED, la línea
7200 Suter Road © 2015 Lutron Electronics Co., Inc
Coopersburg, PA 18036-1299, E.U.A. • Persianas completa de productos CasétaR Wireless y más, visite www.casetawireless.com/features P/N 0301778 REV A