Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Contact Us
Training an Instructor
Quick Enquiry
Related Course
HVAC Course
The thumb rule is that the minimum distance between adjacent butt weld is 1 D . if not, it is never closer than 1 – 1/2 “ . this is
Piping Stress Analys
supposedly to prevent the overlap of HAZs. minimum spacing of circumferential weld between centerlines shall not be less
Course
! is greater.
than 4 times the pipe wall thickness or 25 mm whichever
2) What are weldolet and socket? And where they are used?
Welolet and sockolet are basically self – reinforced fitting. Weldolet is used for butt weld branch connection where standard
tee is not available due to size restriction and the piping is of critical/high pressure service. sockolet is used for socket welding
branch connection , which require reinforcing pad
Piping which is recognized as providing the most uniform application of heat to the process , as well as maintaining the most
uniform processing temperatures where steam tracing is not capable of maintaining the temperature of fluid constant. Usually
used for molten sulphur, polymers service.
Subscribe to Our Newsletter
4)What is the basis of using of short radius & long radius elbow ?
Long radius are used for small pressure drop whereas short radius elbow are used high pressure drops. For catalyst flow Your email address
vary long radius are used
6)How the pipe fittings are classified based on end connections? What do you Mean
NPSH? How do you
No, air pockets may form if concentric reducer is used at pump suction, which results in cavitation and cause damage to
Calculate it?
pump. To avoid this problem, eccentric reducer with Flat Side Up (FSU) is used in pump suction
7)How the pipe fittings are classified based on end connection ? Question Related to
Pipe fittings are classified based on end connection as Mechanical Design
Fundamentals:- Par
A. socket weld fittings.
B. screwed end fittings
Stress / Flexibility
C. beveled end or butt weld fittings
Analysis
D. spigot socket fittings
E. buttress end fittings
When fluid is gas, air or steam and cryogenic service – topside when fluid is liquid – bottom side
Pipe is identified by NB and thickness is defined by schedule whereas tube is identified by OD & its thickness as BWG (
Brimingham Wire Gauge or 1/100 inch ).
11)What should be the radius of long radius elbow ? Suggested For You
Flanges can be classified based on pipe attachment as-slip-on. The slip on type flanges are attached by welding inside as
well as outside. These flanges are of forged construction
Socket weld – The socket weld flanges are welded on one side only. These are used for small bore line only . Piping Stress Types
Screwed – The screwed-on flanges are used on pipe lines where welling cannot be carried out
Lap joint – The lap joint flanges are used with stub ends. The stub ends are welded with pipe & flanges are kept loose over
the same
Piping Design Engi
Welding neck – The welding neck flanges are attached by butt welding to the pipe. These are used mainly for critical service
Interview Questions
where the weld joints need radiographic inspection . 6 (Drums)
Blind – The blind flanges are used to close the ends which need to be reopened
Reducing – The reducing flanges are used to connect between larger and smaller size without using a reducer, In case of
Question Related to
reducing flanges, the thickness of flange be that of the higher diameter. Weld Heat Treatme
Integral – Integral flanges are those, which are cast along with the piping component or equipment
About Oilandgasclub.com
Oilandgasclub.com is an international oil and gas (online & offline) conference technical training org from India.
Oilandgasclub.com 3000+ professionals trained 150,000 hours of classes delivered 500+ expert trainers
available and 3600+ respondents 30+ countries 80+ team. Blogs about technical tips at this blog. Contact or
more about customized technical training from this page
OILANDGASCLUB.COM HAS PUBLISHED 150+ ARTICLES IN THIS BLOG Subscribe Your email address Submit
Share:
News & Articles
Cathodic Protection
More From OilandGasClub Summit CPS-2016
Details
PDMS COURSE IN CHENNAI PDMS COURSE TRAINING INSTITUTE T NAGAR CHENNAI CHENNAI TAMIL NADU PDS COURSE IN NOIDA
PIPE DESIGN COURSE IN CHENNAI PIPELINE DESIGN COURSE PIPELINE DESIGN COURSE IN CHENNAI PIPING COURSE CHENNAI TAMIL NADU
Russia will be Bigge
PIPING COURSE IN CHENNAI PIPING DESIGN COURSE IN CHENNAI PIPING DESIGN COURSE IN CHENNAI WITH PLACEMENT Loser From Oil Pric
WARNA IEA
PIPING DESIGN COURSE IN HYDERABAD PIPING DESIGN COURSE IN MUMBAI PIPING DESIGN COURSE IN NOIDA
PIPING DESIGN ENGINEER INTERVIEW QUESTIONS PIPING ENGINEERING COURSE IN CHENNAI PIPING TRAINING COURSE IN CHENNAI
Related Articles
Abbreviations for About the CAESAR II Placing Dead Weight What is Oil Refinery ? What do Petroleum
Piping Drawings Documentation Support August 3, 2017 Engineers do?
9 days ago September 5, 2017 August 18, 2017 July 13, 2017
Most Important Flexibility Analysis Responsibilities of Role of the Pipe Field American Petroleum
Documents Produced May 22, 2017 Piping Construction Engineer in Safety Institute – (API)
by Piping Engineer Engineers April 25, 2017 April 12, 2017
June 13, 2017 May 6, 2017
I like its very basic questions but there asking too much deep, can add on what kind of external corrosion and internal
Guest corrosion in in-service piping
0 $ | #- Share
I like this page. please share critical piping design consideration with Q & Ans along merits and demerits so as we relate
Guest
ourselves easily and its very easy to understand…
4 $ | #- Share
❯ Structural Design ❯ IOSH Managing Safely ❯ SSPC Training Become an Instructor Corporate Training Mission and Vision
❯ Piping Design ❯ IOSH Working Safely ❯ MEP Training Blog as Guest Courses Offered In-house Solutions
❯ Instrumentation Design ❯ NEBOSH Training ❯ NDT Training Become an Affiliate Why Oilandgasclub.com
Your email address Submit How to its Work Click Here for Webinars
About Oilandgasclub Contact Us Partner Us Career Job Listing Events Membership Blog News Policies In-house Solutions Build Your Po
Copyright © 2017 Acusstreak. All rights reserved. The certification names and logos are the trademarks of their respective owners.
Follow Us! Subscribe to Our Newsletter Learn Online Register Webinars Student Login