Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Metering Systems
Batch Control Systems (Low Viscosity) 20
Batch Control Systems (High Viscosity) 21
Flow Meters
Turbine & Oval Gears Meters 22
Worldwide Distribution 23
3
4
Pump Packages
5
Pump Packages Continued
6
Drum Pump Motors DATA SHEET
SP-ODP Series
Model Enclosure Power Watt V.S.D.
SP-ODP O.D.P 115/1/50-60 450 No
SP-ODP-2 O.D.P 230/1/50-60 450 No
Warning: Not Suitable For Pumping Flammable or Combustible Liquids NOTE: V.S.D. = Variable Speed Drive
SP-280P Series
Model Enclosure Power Watt V.S.D.
SP-280P O.D.P (IP44) 115/1/50-60 825 No
SP-280P-V O.D.P (IP44) 115/1/50-60 825 Yes
SP-280P-2 O.D.P (IP44) 230/1/50-60 825 No
SP-280P-2-V O.D.P (IP44) 230/1/50-60 825 Yes
Warning: Not Suitable For Pumping Flammable or Combustible Liquids NOTE: V.S.D. = Variable Speed Drive
SP-ENC Series
Model Enclosure Power Watt V.S.D.
SP-ENC T.E.F.C (IP 54) 115/1/50-60 825 No
SP-ENC-V T.E.F.C (IP 54) 115/1/50-60 825 Yes
SP-ENC-2 T.E.F.C (IP 54) 230/1/50-60 825 No
SP-ENC-2-V T.E.F.C (IP 54) 230/1/50-60 825 Yes
Warning: Not Suitable For Pumping Flammable or Combustible Liquids NOTE: V.S.D. = Variable Speed Drive
SP-400 Series
Model Enclosure Power Watt V.S.D.
SP-400-2 EXP (IP54) 230/1/50-60 550 No
EEx de IIA T6 II2G
See warning at bottom of page. NOTE: V.S.D. = Variable Speed Drive
SP-A2 Series
Model Consumption Max. Inlet Pressure Output
SP-A2 28 CFM@90 psi 100 psi 3/4 hp
13.2 L/sec @ 6.2 bar 6.8 bar 560 w
SP-A2L 28 CFM@90 psi 100 psi 3/4 HP
(trigger lock) 13.2 L/sec.@6.2 bar 6.8 bar 560 W
SP-A1 Series
Model Consumption Max. Inlet Pressure Output
SP-A1 22 CFM@90 psi 100 psi 1/2 hp
10.4 L/sec @ 6.2 bar 6.8 bar 370 w
WARNING: Pumping of flammables or combustible liquids can generate a static electric discharge, causing fire or explosion resulting in injury or death. Read and under-
stand operating instructions before starting this unit. Follow all federal, state and local safety codes including NFPA 30 - NFPA77. Prior to connecting to air supply, install
bond and ground wires and check continuity of each wire. A meter reading of one ohm or less is required for safe liquid transfer. Use only metallic drum, receiving vessel 7
and metallic pump (SP-SS) when pumping flammables. Air motors are not recognized under any current Underwriter’s Laboratory listing program. Consult a qualified
engineer for suitability for use in a hazardous area or on flammables.
PVDF Series DATA SHEET
Common Applications
Technical Data
8
CPVC Series DATA SHEET
STANDARDS's CPVC pump tube is engineered for transferring corrosive chemicals as-
sociated with the water treatment industry. Robust CPVC offers excellent durability and
chemical resistance.
Common Applications
Technical Data
9
Stainless Steel Series DATA SHEET
STANDARDS's Stainless pump tube is engineered for transferring flammable and com-
bustible liquids. Robust Stainless Steel 316 offers excellent strength and durability.
Common Applications
Technical Data
10
Polypropylene Series DATA SHEET
Common Applications
Technical Data
11
High Temperature Polypropylene Series DATA SHEET
STANDARDS's Polypropylene (PHT) pump tube is engineered for transferring high tem-
perature corrosive liquids. Robust Polypropylene ensures chemical resistance and excellent
heat deflection against light to mildly aggressive media.
Common Applications
Technical Data
12
Motor & Tube Assembly Detail
13
13
Centrifugal Drum Pump Accessories
TRANSFER HOSE
PART NUMBER: TRANSFER HOSE DESCRIPTION
9029 Clear PVC 1" I.D. x 1.25" O.D. (28 mm x 31 mm)
Max operating pressure: 30 psi (2 bar)
9032 Clear braided PVC 1" I.D. x 1.25" O.D. (28 mm x 31 mm)
Max operating pressure: 130 psi (8.9 bar)
14
SP-700SR High Viscosity Series
DATA SHEET
The SP-700SR pumps are engineered specifically for transferring viscous materials from drums and tanks commonly
found in the industrial marketplace. The progressive cavity design deliverers a continuous, smooth flow of material
with little product degradation. Maximum viscosity is 25,000 cps (mPAS).
SP-280 Series
Technical Data
Design: Progressive Cavity / Positive Displacement
Max. Viscosity: 25,000cps (mPAS)
Pump Intake: 2” /50mm
Discharge Port: 1.5” / 38mm hose barb, optional 1.25” /32mm
Stator Materials: Teflon, Viton or Buna-N
SP-ENC Series
Mechanical Seal: SiC/Viton/SiC
Immersion Lengths: 27” (700mm)
39” (1000mm)
47” (1200mm)
Please add 6” (150mm) to the Immersion
length of pump for the 752 series pumps.
Wetted Material: Tube & Rotor Assembly: 316 Stainless Steel
Stator Material: Teflon, Viton, or Buna
Motor Drives: SP-280P, SP-ENC, SP-400-2, SP-A2 Series. SP-400 Series
Consult chart for viscosity ratings.
Fittings: Large Type Acme Thread design enables
operator to disassemble pump quickly for
cleaning, maintenance, and inspection.
Max Flow Rate: 17GPM / 64 LPM
Max Pressure: 174 psi / 12 bar
SP-A2 Series
Benefits
• Easy Maintenance
• Threaded Components
• Interchangeable Motors Drives
• Continuous Flow
• Low Shearing Properties
Discharge Fitting
Warning: When pumping flammable or combustible
liquids pump tube must be used in conjunction with
an explosion proof motor.
15
SP-700DD High Viscosity Series DATA SHEET
The SP-700DD pumps are engineered specifically for transferring viscous materials from drums and tanks commonly
found in the Industrial marketplace. The progressive cavity design delivers continuous flow of material with little
product degradation. Maximum viscosity is 100,000 cps (mPAS).
Motor Drives
Common Applications
• Polymers • Oil & Greases
• Resins • Paints
• Adhesives • Varnishes
Pneumatic
Benefits
• Easy Maintenance
• Threaded Components
• Continuous Flow
• Low Shearing Properties
Discharge Fitting
Warning: When pumping flammable or combustible
liquids pump tube must be used in conjunction with
an explosion proof motor.
16
SP-700DD Pump Motors DATA SHEET
SP-A4 2 1,5 300–900 80 CFM @ 100 psi IEC#72/D71 1/4” (6.35) 12 (5)
37 L/Sec @ 7 Bar
SP-A6 4 3,0 300–900 130 CFM @ 100 psi IEC#72/D80 1/2” (12.7) 24 (11)
65 L/Sec @ 7 Bar
SP-A8 5 3,7 300–900 170 CFM @ 100 psi IEC#72/D90 1/2” (12.7) 26 (12)
80 L/Sec @ 7 Bar
17
Performance Curves
90 (6) 90 (6)
Pressure — PSI (BAR)
80 (5) 80 (5)
70 (4) 70 (4)
60 (3.5) D C B A 60 (3.5) D C B A
50 (3) 50 (3)
40 (2) 40 (2)
30 (1.5) 30 (1.5)
20 (1) 20 (1)
10 (.5) 10 (.5)
0 0 0 0
0 2 (8) 4(15) 6 (23) 8 (30) 10 (38) 12 (45) 14 (53) 0 2 (8) 4 (15) 6 (23) 8 (30) 10 (38) 12 (45) 14 (53) 16 (61) 17(64) 18 (68)
Flow Rate — GPM (LPM) Flow Rate — GPM (LPM)
Curve Viscosity HP KW Curve Viscosity HP KW
(cps) (cps)
A 1+ .5 ,37 A 1+ .5 ,37
B 10,000+ 1 ,75 B 10,000+ 1 ,75
C 20,000+ 1 1,2 C 20,000+ 1 1,2
D 30,000+ 1.5 1,2 D 30,000+ 1.5 1,2
NOTE: Accuracy of performance curves may vary +/- 10% based on specific applications.
18
Progressive Cavity Drum Pump Accessories
QUICK DISCONNECT
PART NUMBER: QUICK DISCONNECT DESCRIPTION
150DSS/150ESS 1.5” ( 38 mm), SS316 Cam Lever Couplings,
BUNA N gaskets, Max. pressure: 150 psi ( 10 BAR).
19
Batch Control System (Low Viscosity) DATA SHEET
STANDARD’S Batch Control System (BCS) is engineered to control, measure and dispense preset volumes of liquid from
drums, IBC‘s, plating tanks or any large storage vessel. The BCS‘s can be used in an industry where batching, chemical
packaging or dilution is required to be accurate and efficient. Simply dial in the desired volume, press ENTER & the BCS
delivers a preset volume of liquid from drums & tanks virtually hands-free.
Features
• Measure flow rate and volume
• Turbine Paddle Wheel Design
• Multiple languages
• Measures: gallons, liters, cubic meters, milliliters, imperial gallons
• Re settable Totalizer
• +/- .05 % accuracy of reading
Common Applications
• Chemical Packaging • Adding Water Treament Chemicals
• Adding Chemistry To Plating Tanks • Chemical Delivery
Technical Specifications
20
Batch Control System (High Viscosity) DATA SHEET
STANDARD’S Batch Control System (BCS) is engineered for high precision dosing and filling operations involv-
ing viscous materials. This Batch Control System is constructed with robust materials and a choice of motor
drives, therefore offering versatility and safety for the most challenging applications. Simply dial in desired volume,
press enter, and the BCS delivers a preset volume of material from drums and tanks – virtually hands-free.
Features
• Measure flow rate and volume
• Oval gear design
• Multiple languages
• Measures: gallons, liters, cubic meters, milliliters, imperial gallons
• Re settable Totalizer
• +/- .05 % accuracy of reading
Oval Gear Design
Common Applications
• Polymers • Oils • Varnishes
• Paints • Resins • Petroleum Products
Technical Specifications
9” (228mm)
2” (50mm)
21
Flow Meters Industrial Series DATA SHEET
22
23
Industrial Pumps & Metering Systems Sanitary Pumps & Metering Systems
Copyright © 2007 STANDARD PUMP, INC. and its licensors. All rights reserved.