Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
com
Safety Precautions 02
Product Contents 04
Product PIN Diagram 06
LED indicators 06
Product Dimensions 07
Installation of Panel with Casing 08
Wire Legend 09
Power Wiring Diagram 10
FR1200 Connection 11
Weigand Connection 12
Exit button Connection 12
Lock connection 13
Door Sensor Connection 13
Aux. Input Connection 15
Aux. Output Connection 15
Ethernet Connection 16
RS485 Connection 17
DIP switch settings 18
Electrical Specifications 19
Troubleshooting 20
Specifications 21
1
1Safety Precautions
The list below is to keep user’s safety and prevent any loss. Please read carefully before installation.
01 02 03
Do not place a magnet near the Do not place the device next to
Do not install the device in an area heating equipments
product. Magnetic objects such as
subject to direct sun light, Humidity
magnet, CRT, TV, monitor or speaker
or dust
may damage the device.
04 05 06
Be careful not to let liquid like Clean the device often to remove Do not let children touch the
water, drinks or chemicals leak dust on it device without supervision.
inside the device.
2
Safety Precautions
The list below is to keep user’s safety and prevent any loss. Please read carefully before installation.
07 08 09
Do not drop the device. Do not disassemble, repair or Do not use the device for any
alter the device. other purpose than specified.
10 11 12
Do not damage the device In cleaning, do not splash water Contact your nearest dealer in
on the device but wipe it out with case of a trouble or problem.
smooth cloth or towel.
3
Product Contents
Basic Contents
Wall Mounting Screws – 2 pcs. Wall Plugs– 2 pcs. Surge Suppressing Diode– 4 pcs.
Inbio460
4
Product Contents
Optional accessories
Weigand Card Reader Prox Card FR1200 FP Reader K1-1 Exit Button
ZK4500 FP Enrollment reader Card Enroller Inbio Metal Case RS485 convertor
5
Product PIN Diagram
SD Card Slot
LED indicators
LINK LED
Aux Input 1 LED solid green indicates
Ethernet Port LINK
TCP/IP communication is
(Green)
ACT LED normal
Aux Input 4
DIP Switch
FR1200
ACT Flashing LED indicates data
Fingerprint
PC RS485 Port Reader (Yellow) communication is in progress
Aux Output 1 State Indictor
EXT RS485
#1 Door Exit Flashing LED indicates data
Button (Yellow &
communication in progress
#1 Door Card Green)
Aux Output 4 Reader
#2 Door Exit PC RS485
#1 Door Sensor Flashing LED indicates data
Button (Yellow &
#1 Door Lock communication is in progress
#2 Door Card Green)
Reader
#3 Door Exit
Button POWER Flashing LED indicates the
(Red) panel is powered on.
#3 Door Card
Reader
#4 Door Sensor Flashing LED indicates that
#4 Door Exit RUN
#4 Door Lock Button panel is in normal working
(Green)
Lock Power #4 Door Card mode
Reader
Inbio Power
CARD Flashing LED indicates that
(Yellow) the card is read by the panel.
6
Product Dimension
Inbio460
106mm 106mm
(4.17in.) (4.17in.) 36mm
(1.42in.)
Dimensions(L*W*H):226× 106× 36(mm)
226mm 8.89× 4.17× 1.42(inches)
(8.89in.)
InBio-Casing
330mm 330mm
(13.0in.) (13.0in.) 90.5mm
(3.56in.)
7
Installation of Panel & Case
Metal Case
8
Wire Legend
Detector Infrared sensors FR1200 Inbio-Box #1Exit Button #1Card Reader #4 Exit Switch #4 Card Reader
DC
12V DC
Power
12V
Network RS485 Convertor Floodlight Alarm Normally Close Lock Normally Open Lock Power Supply
9
Power wiring diagram
Without AC 110-220V
Inbio460
Backup Battery
AC
With
Backup Battery
AC 110-220V
Inbio460
+
Backup Battery
-
AC
10
FR1200 Connection
12V DC
12V DC
1. There are six DIP switches on the back of FR1200 , Switches 1-4 is for RS485
address , switch 5 is reserved , switch 6 is for reducing noise on long RS485 cable.
2. Set the odd number for IN reader, and the even number for OUT reader(for eg.
For two readers for one door- the RS485 address 1 is for IN reader, RS485 address
2 is for OUT reader )
3. If FR1200 is powered from Inbio460 panel ,the length of wire should be less
than 100 meters or 330 ft.
4. The External RS485 interface can supply maximum 500mA current , The
FR1200’s startup current is 240mA. So Inbio460 only can only power two FR1200s.
5. If the cable length is more than 200 meters or 600 ft , the number 6 switch
should be ON as below
Distance
11
Weigand Connection
Beeper
Green LED
Weigand D1
Weigand D0
GND
DC+(6-14V)
DV12V(+)
DV12V(-)
BUT
NO
GND COM
NC
12
Lock Connection
For Normally Open -Lock powered from panel power supply FR107
GND
12V DC
Sensor
Sensor
GND
12V DC
FR107
For Normally Closed -Lock powered from panel power supply
12V DC
GND
Sensor
Sensor
GND
12V DC
13
Lock Connection
Switching Wet Contact to Dry Contact
Steps:
Important Notes:
GND
12V DC
FR107
14
Auxiliary Input/Output
Aux. Input Connection
Smoke Detector
12V DC
GND
COM
NO
NC
Alarm
12V DC
GND
COM
NO
NC
15
Ethernet Connection
Important Notes:
Direct connection
To connect Inbio460 with a PC directly, connect both devices with a straight network cable. As the Inbio460 supports auto MDI/MDIX ,
it is not necessary to use a crossover type cable.
ZK4500 Enrollment
reader
CR10 Card Issuer
16
RS485 Connection
#63 Inbio460
RS485-
RS485+
#1 Inbio460 GND
Distance
#1 Inbio460 #* Inbio460
17
DIP Switch Setting
Introduction RS485 Address
1. Number 1-6 are reserved to set the device number for RS485
communication. The code is binary, and the numbering starts from left to
right. When the switch is set to ON position, it indicates 1 (on); when the
switch is set downwards, it indicates 0 (off). For example, to set a device
number 39=1+2+4+32, which corresponds to the binary code 111001, put
number 1, 2, 3, and 6 to ON position, as illustrated below.
2. For more details, please check the table at the end of this document
1. If you forget the inBio IP address or the device does not work 1. Number 8 is for setting the RS485 termination resistance. Putting the
normally, you can use the number 7 terminal to restore inbio460 to switch to ON position is equivalent to parallel connection of a 120ohm
factory default settings. The parameters which gets reset are termination resistance between 485+ and 485-
device IP address, communication password ,gateway ,subnet mask. 2. As shown in diagram below, for more info please read RS485 connection
2. The switch is OFF by default. When it is moved upwards and important notes
downwards for three times within 10 seconds and finally returned
to OFF position, the factory settings will be restored after the
access control panel is restarted.
1 times 2 times 3 times OFF
120ohm
18
Electrical Specification
19
Troubleshooting
1. Fingerprint can not be read well or it takes too long.
Check whether a finger or fingerprint sensor is stained with sweat, water, or dust
Retry after cleaning the finger and fingerprint sensor with dry cloth.
Reset Button
If a finger is way too dry, rub your finger on the palm and retry.
Try to reset fingerprint sensor by pressing the reset button at the bottom of the reader
20
Specification
Communication RS485, Ethernet
Baud Rate for RS485 9600-115200 baud
Power Supply 12V DC, 3A
Device Capacity Card capacity 30,000 ; Log events capacity 100,000 ; Finger capacity 3,000
LED Indicator Indication for communication, power, status and prox card
Environment Operating Temp: 32-113 °F (0-45 °C) Operating Humidity: 20% to 80%
Number of doors controlled four door one way or two door two way
Number of card readers supported 4
Number of FR1200 supported 8
FR1200 Sensor Fingerprint sensor 500dpi Optical / Optical sensor
Types of readers supported 26-bit Weigand, others upon request
Number of Inputs 12 (4 Exit Device, 4 Door Status, 4 AUX)
Number of Outputs 8 (4- Form C relay for lock and 4- Form C relay for Aux output)
Weight 7.8lbs (3.55kg)
Enclosure Stainless Steel
Mounting Wall Mount
Dimensions (Bundle Only) 15.7in. × 3.56in.× 13.0in. 400mm(L) X 90.5mm(W) X 330mm(H)
Dimensions ( Board Only) 8.89in.× 4.17in.× 1.42in. 226mm(L) X 106mm(W) X 36mm(H)
CPU 32 bit 400MHz
RAM 32MB
Flash 128MB
Certified
21
PC485 Table
22
Functions and specifications of the product are subject to change without notice due to quality enhancement or function update. For any inquiry
for the product, please contact ZKTeco Inc .
ZK China :
ZK Building, Wuhe Road, Gangtou,
Bantian, Buji Town, Longgang District,
Copyright 2013 ZKTeco Inc. All right reserved. Shenzhen China.
ZKTeco May, at any time and without notice , Make changes or Tel.: +86 755-89602345
improvements to the product and services offered and/or cease sales@zkteco.com
producing or commercializing them. zkteco.com