Sei sulla pagina 1di 4

Chemical

10/18/12
Composition And Mechanical Properties of Steel (Indian Standard)

THINK!- MARYLAND METRICS - The One-Stop Source For Metric And British Sized Fasteners, Wrenches,
Cutting, & Measuring Tools, Metal Shapes, Oil Seals, O-Rings, Mechanical Power Transmission Equipment,
Bearings, Hydraulic And Pneumatic Fittings & Tubing, Workholding Components, Plumbing Fittings, & Some
Electrical & Electronic Components. Click to go to Maryland Metrics home page

Chemical Composition And Mechanical Properties of Steel (Indian Standard)

IS : 10748 - Specification Of Hot Rolling Steel Strips For Welded Tubes & Pipe
CHEMICAL COMPOSITION
Grade C% Max Mn % Max. S% Max. P% Max.
I 0.10 0.50 0.05 0.05
II 0.12 0.60 0.05 0.05
III 0.16 1.20 0.05 0.05
IV 0.20 1.30 0.05 0.05
V 0.25 1.30 0.05 0.05
MECHANICAL PROPERTIES
Grade UTS ( Min.) Mpa YS ( Min.) Mpa EI. % ( Min. ) 5.65 Sqrt (So)
I 290 170 30
II 330 210 28
III 410 240 25
IV 430 275 20
V 490 310 15

IS : 6240 HR - Steel Plate, Sheet and Coil for LP


CHEMICAL COMPOSITION
Constituent Percent
Carbon, Max. 0.16
Manganese, Min 0.30
Silicon, Max. 0.25
Sulphur, Max. 0.030
Phosphorous, Max. 0.030
Aluminium, Min 0.02
MECHANICAL PROPERTIES
Property Grade *
Tensile Strength Mpa (kgf/mm²) 350 to 450 ( 36 to 46 )
Yield Strength. Mpa ( Kg/mm²) Min 240 (25)
Elongation, Min percent on guage length 5.65 OSo 25
Bend t
EC v ( for 2.80-3.15 mm thickness) min 13.5
* Both longitudinal and transverse directions.

TOLERANCE AS PER IS : 513


Tolerance on Thickness of Sheets
Tolerance on the thickness for different width
Nominal Upto 1250 Above 1250
Abov e 1600
Thickness mm Upto 1600
Upto 0.25 +/- 0.03 - -
Above 0.25-0.40 +/- 0.04 - -

mdmetric.com/tech/chempropi.htm 1/4
Above 0.40-0.60 +/- 0.05 +/- 0.06 -
Above 0.60-0.80 +/- 0.06 +/- 0.07 +/- 0.08
Above 0.80-1.00 +/- 0.08 +/- 0.09 +/- 0.10
Above 1.00-1.25 +/- 0.09 +/- 0.10 +/- 0.12
Above 1.25-1.60 +/- 0.11 +/- 0.12 +/- 0.14
Above 1.60-2.00 +/- 0.12 +/- 0.14 +/- 0.16

Tolerance on Width Of Sheets


Width of Sheets Tolerance
Upto 1250 mm +7 -0
Above 1250 mm +10 -0

Tolerance on Length of Sheets


Length Tolerance
Upto 2000 mm +15 -0
Above 2000 mm +0.75 % of the length -0

Chamfer Tolerance For Coils and Cut Length


Form Tolerance
Coil 20 mm in any 5000 mm length
C ut Le ngth 0.4% X le ngth

Standard Flatness Tolerance for cut lengths


Tolerance on specified width
Thickness
Upto 1200 Above 1200 - Upto 1500 Above 1500
Upto 0.63 15 18 22
Above 0.63-1.25 12 15 19
Above 1.25 10 12 17

Special Flatness Tolerance for


Cut lengths Roller Levelled and Stretcher Levelled
Tolerance on specified width
Thickness
Upto 1200 Above 1200 Upto 1500 Above 1500
Upto 0.63 6 7 8
Above 0.63-1.25 5 6 7
Above 1.25 4 5 6

IS : 2062 - Specification of Steel for General Structural Purposes


CHEMICAL COMPOSITION
Grade C% Max. Mn% Max. S% Max. P% Max. Si% Max. C.E.% Max.
A 0.23 1.50 0.050 0.050 0.40 0.42
B 0.22 1.50 0.045 0.045 0.40 0.41
C 0.20 1.50 0.040 0.040 0.40 0.39
MECHANICAL PROPORTIES
Bend
Grade UTS(MPa) Min. Y.S.(MPa) Min. El.% Min. 5.65 Sqrt(So)
Test
A 410 250 240 230 23 3T
B 410 250 240 230 23 2T & 3T *
C 410 250 240 230 23 2T
* 2T - <= 25mm
* 3T - > 25mm
Chemical
10/18/12
Composition And Mechanical Properties of Steel (Indian Standard)

IS : 3039 - Spe cification of Structural Ste e l for Ship Building


C HEMIC AL C O MPO SITIO N
Grade C% Max. Mn% S% Max. P% Max. Si% Max. A l% Min.
I 0.23 * 0.040 0.040 ** 0.01
II 0.21 0.70-1.4 0.040 0.040 0.10-0.35 -
III 0.18 0.70-1.5 0.040 0.040 0.19-0.50 0.015
MEC HANIC AL PR O PER TIES
Y.S. (MPa) Min. EI.% Min.
Grade UTS (MPa)
< 25 mm. > 25 < 50 mm. 5.65 Sqrt (So)
I 400-490 230 220 22
II 400-900 235 235 22
III 400-490 235 235 22

IS : 1786 - High Strength Deformed Steel Bars and Wires for Concrete Reinforcement
C HEMIC AL C O MPO SITIO N
SA IL-TMT(Fe
Constituent Percent, Maximum 415/FE 500/Fe
550)
SA IL SA IL
SA IL
TMT Fe 415 Fe 500 TMT Fe 500
TMT 500
415 550
C arbon 0.25 0.30 0.25 0.30 0.25 0.30 0.20
Sulphur 0.05 0.06 0.05 0.055 0.05 0.055 0.045
Phosphorus 0.05 0.06 0.05 0.055 0.05 0.050 0.045
Sulphur and
0.10 0.11 0.10 0.105 0.10 0.10 0.09
Phosphorus
C orrosion R e sistant
- - - - - - 0.75 m in
Ele m e nts
C arbon Equivale nt - - - - - - 0.53 m ax
MEC HANIC AL PR O PER TIES
Property Grade
SA IL SA IL SA IL
Fe Fe
Fe 415 TMT TMT TMT
500 550
415 500 550
0.2 pe rce nt proof
stre ss/yie ld stre ss 415 415 500 500 550 550
Min N/m m .sq.
Elongation.pe rce nt
,Min,on gauge le ngth 22(Up to 20(Up to 18(Upto 25 m m dia)
5.65.Square R oot(A) 28m m dia) 28m m dia)
14.5 12 8
whe re A is the cross- 20 (Above 18 (Above
se ctional are a of the 28 m m dia) 26 m m dia) 16(Above 28 m m dia)
te st pie ce
Te nsile Stre ngth,Min. 10% m ore 10% m ore 8% m ore 8% m ore 6% m ore 6% m ore than the actual
than the than the than actual than the than the 0.2% proof
actual 0.2% actual 0.2% 0.2% proof actual 0.2% actual stre ss but not le ss than 630
proof stre ss proof stre ss stre ss but proof stre ss 0.2% proof N/m m .sq.
but not le ss but not le ss not le ss but not le ss stre ss but (Upto 28m m dia)
than 48.5 than 500 than 545 than 580 not le ss & 610 N/m m .sq.
N/m m .sq. N/m m .sq. N/m m .sq. N/m m .sq. than 585
N/m m .sq. (above 28 m m dia)
(Upto 28m m
dia) & 560 (Upto 28m m Upto 28m m dia) & 560
N/m m .sq.) dia) & 560 N/m m .sq.)
(above 28 N/m m .sq.) (above 28 m m dia)
m m dia) (above 28
m m dia)

SPECIFICATION FOR WIRE RODS


Chemical Composition Mechanical Properties
Specifications Grade %C %Mn %S %P Yield Tensile Elongation
Mpa Mpa %
Structure Q uality IS2062 0.23 m ax 1.50 m ax 0.05 m ax 0.50 m ax 250 m in 410 m in 23 m in
mdmetric.com/tech/chempropi.htm 3/4
Chemical
10/18/12
Composition And Mechanical Properties of Steel (Indian Standard)
W ire R ods Grade A
Drawing Q uality SW R -14 0.14 m ax 0.60 m ax 0.05 m ax 0.05 m ax - - -
W ire R ods 0.08-013 0.30-0.60 0.05 m ax 0.04 m ax
Low C arbon Drawing SW R -10 0.1 m ax 0.6 m ax 0.04 m ax 0.04 m ax - - -
Q uality W ire R ods SAE-1008 0.1 m ax 0.3 m ax 0.05 m ax 0.04 m ax
Ele ctrode Q uality IS-2879 0.1 m ax 0.38-0.62 0.03 m ax 0.03 m ax - - -
W ire R od R im m ing Grade

IS:1079-Spe cification of Hot R olle d C arbon Ste e l She e ts & Strips


C HEMIC AL C O MPO SITIO N
C% Mn % S% P%
Grade
Max Max Max Max
O 0.15 0.60 0.055 0.055
D 0.12 0.50 0.04 0.04
DD 0.10 0.45 0.035 0.035
EDD 0.08 0.40 0.030 0.03
MEC HANIC AL PR O PER TIES
UTS YS(Min.) EI.% Min.
Grade
MPa MPa Lo-80 mm b-20 mm
O - - -
D - - 28
DD 260-390 - 32
EDD 260-380 - 36

Spe cification C he m ical com position (m ax ) Me chanical Prope rtie s


%
Tensile Yield Elongation
C Mn S P Strength Strength guage Nb+V+T
Min. Mpa Min. Mpa length
5.65 So
IS-2062 Gr A (SK) 0.23 1.5 0.050 0.050 410 240 23 0.20
IS-2062 Gr B (SK) 0.20 1.5 0.045 0.045 410 240 23 .
SAIL-MA 300 0.25 1.5 0.055 0.055 440-560 300 20
SAIL-MA 300 HI 0.20 1.5 0.040 0.040 440-560 300 21 Max im um
for all
SAIL-MA 350 0.25 1.5 0.040 0.040 490-610 350 20
SAIL-MA 350 HI 0.20 1.5 0.040 0.040 540-660 410 19 .
SAIL-MA 410 0.25 1.5 0.040 0.040 540-660 410 20 .

THINK!- MARYLAND METRICS - The One-Stop Source For Metric And British Sized Fasteners, Wrenches,
Cutting, & Measuring Tools, Metal Shapes, Oil Seals, O-Rings, Mechanical Power Transmission Equipment,
Bearings, Hydraulic And Pneumatic Fittings & Tubing, Workholding Components, Plumbing Fittings, & Some
Electrical & Electronic Components. Click to go to Maryland Metrics home page

Phones: (800) 638-1830 or (410) 358-3130 are available Monday-Friday 8:30 AM to 5:30 PM Eastern time.
Faxes: (800) 872-9329 or (410) 358-3142 & E-mail are available anytime.
Warehouse & showroom hours are Monday-Friday 10 AM to 5:30 PM.
[ To: Maryland Metrics home page ] [ To: Maryland Metrics Product Guide ] [ e-mail to Maryland Metrics ]
Please note that all Trademarks and Tradenames are the property of their respective owners.
copyright 2000, 2009, 2011 maryland metrics -- all rights reserved -- ver gg22a chempropi.htm

4/4

Potrebbero piacerti anche