Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
.
protection against :
OUTPUT DC AND AC SHORT CIRCUIT TO
.. GROUND
OVERRATING CHIP TEMPERATURE MULTIWATT11
PIN CONNECTION
SCHEMATIC DIAGRAM
THERMAL DATA
Symbol Parameter Value Unit
R th j-case Thermal Resistance Junction-case Max. 3 °C/W
2/21
TDA2005
3/21
TDA2005
ELECTRICAL CHARACTERISTICS (refer to the Bridge application circuit, Tamb = 25oC, GV = 50dB,
Rth (heatsink) = 4oC/W, unless otherwise specified)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
Vs Supply Voltage 8 18 V
Vos Output Offset Voltage (1) Vs = 14.4V 150 mV
(between pin 8 and pin 10) Vs = 13.2V 150 mV
Id Total Quiescent Drain Current Vs = 14.4V RL = 4Ω 75 150 mA
Vs = 13.2V RL = 3.2Ω 70 160 mA
Po Output Power d = 10% f = 1 Hz W
Vs = 14.4V RL = 4Ω 18 20
RL = 3.2Ω 20 22
Vs = 13.2V RL = 3.2 Ω 17 19
d Distortion f = 1kHz
Vs = 14.4V RL = 4Ω
Po = 50mW to 15W 1 %
Vs = 13.2V RL = 3.2Ω
Po = 50mW to 13W 1 %
Vi Input Sensitivity f = 1kHz
Po = 2W RL = 4Ω 9 mV
Po = 2W RL = 3.2Ω 8 mV
Ri Input Resistance f = 1kHz 70 kΩ
fL Low Frequency Roll Off (– 3dB) RL = 3.2Ω 40 Hz
fH High Frequency Roll Off (– 3dB) RL = 3.2Ω 20 kHz
Gv Closed Loop Voltage Gain f = 1kHz 50 dB
eN Total Input Noise Voltage Rg = 10kΩ (2) 3 10 µV
SVR Supply Voltage Rejection Rg = 10kΩ, C4 = 10µF 45 55 dB
fripple = 100Hz, Vripple = 0.5V
η Efficiency Vs = 14.4V, f = 1 kHz
Po = 20W RL = 4Ω 60 %
Po = 22W RL = 3.2Ω 60 %
Vs = 13.2V, f = 1 kHz
Po = 19W RL = 3.2Ω 58 %
Tj Thermal Shut-down Junction Vs = 14.4V, RL = 4Ω 145 °C
Temperature f = 1kHz, Ptot = 13W
VOSH Output Voltage with one Side of Vs = 14.4V RL = 4Ω
the Speaker shorted to ground Vs = 13.2V RL = 3.2Ω 2 V
Notes : 1. For TDA2005M only
2. Bandwith Filter : 22Hz to 22kHz.
4/21
TDA2005
Figure 3 : Output Offset Voltage versus Figure 4 : Distortion versus Output Power
Supply Voltage (bridge amplifier)
5/21
TDA2005
Voltage and current swings are twice for a bridge For sufficiently high gains (40 to 50dB) it is possible
amplifier in comparison with single ended amplifier. to put R2 = R4 and R3 = 2 R1, simplifing the formula
In order words, with the same RL the bridge con- in :
figuration can deliver an output power that is four R1
times the output power of a single ended amplifier, GV = 4
R2
while, with the same max output current the bridge
configuration can deliver an output power that is Gv (dB) R 1 (Ω) R2 = R4 (Ω) R3 (Ω)
twice the output power of a single ended amplifier. 40 1000 39 2000
Core must be taken when selecting VS and RL in 50 1000 12 2000
order to avoid an output peak current above the
absolute maximum rating.
From the expression for IO max, assuming Figure 6 : Bridge Configuration
VS = 14.4V and VCE sat = 2V, the minimum load
that can be driven by TDA2005 in bridge configu-
ration is :
VS − 2 VCEsat 14.4 −4
RL min = = = 2.97Ω
IO max 3.5
The voltage gain of the bridge configurationis given
by (see Figure 34) :
V0 R1 R3
GV = =1+ +
V1 R2 ⋅ R4 R4
R +R
2 4
6/21
TDA2005
ELECTRICAL CHARACTERISTICS (refer to the Stereo application circuit, Tamb = 25oC, GV = 50dB,
Rth (heatsink) = 4oC/W, unless otherwwise specified)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
Vs Supply Voltage 8 18 V
Vo Quiescent Output Voltage Vs = 14.4V 6.6 7.2 7.8 V
Vs = 13.2V 6 6.6 7.2 V
Id Total Quiescent Drain Current Vs = 14.4V 65 120 mA
Vs = 13.2V 62 120 mA
Po Output Power (each channel) f = 1kHz, d = 10% W
Vs = 14.4V R L = 4Ω 6 6.5
R L = 3.2Ω 7 8
R L = 2Ω 9 10
R L = 1.6Ω 10 11
Vs = 13.2V R L = 3.2Ω 6 6.5
R L = 1.6Ω 9 10
Vs = 16V R L = 2Ω 12
d Distortion (each channel) f = 1kHz
Vs = 14.4V R L = 4Ω
Po = 50mW to 4W 0.2 1 %
Vs = 14.4V R L = 2Ω
Po = 50mW to 6W 0.3 1 %
Vs = 13.2V R L = 3.2Ω
Po = 50mW to 3W 0.2 1 %
Vs = 13.2V R L = 1.6Ω
Po = 40mW to 6W 0.3 1 %
CT Cross Talk (1) Vs = 14.4V, Vo = 4VRMS dB
RL = 4Ω, Rg = 5kΩ
f = 1kHz 60
f = 10kHz 45
Vi Input Saturation Voltage 300 mV
Vi Input Sensitivity f = 1kHz, Po = 1W mV
R L = 4Ω 6
R L = 3.2Ω 5.5
Ri Input Resistance f = 1kHz 70 200 kΩ
fL Low Frequency Roll Off (– 3dB) RL = 2Ω 50 Hz
fH High Frequency Roll Off (– 3dB) RL = 2Ω 15 kHz
Gv Voltage Gain (open loop) f = 1kHz 90 dB
Gv Voltage Gain (closed loop) f = 1kHz 48 50 51 dB
∆ Gv Closed Loop Gain Matching 0.5 dB
eN Total Input Noise Voltage Rg = 10kΩ (2) 1.5 5 µV
SVR Supply Voltage Rejection Rg = 10kΩ, C3 = 10µF 35 45 dB
fripple = 100Hz, Vripple = 0.5V
η Efficiency Vs = 14.4V, f = 1kHz
Po = 6.5W R L = 4Ω 70 %
Po = 10W R L = 2Ω 60 %
Vs = 13.2V, f = 1kHz
Po = 6.5W R L = 3.2Ω 70 %
Po = 100W R L = 1.6Ω 60 %
Tj Thermal Shut-down Junction Temperature 145 °C
Notes : 1. For TDA2005M only
2. Bandwith Filter : 22Hz to 22kHz.
7/21
TDA2005
Figure 8 : Quiescent Output Voltage versus Figure 9 : Quiescent Drain Current versus
Supply Voltage (Stereo amplifier) Supply Voltage (Stereo amplifier)
Figure 12 : Output Power versus Supply Voltage Figure 13 : Distortion versus Frequency
(Stereo amplifier) (Stereo amplifier)
8/21
TDA2005
Figure 16 : Supply Voltage Rejection versus Figure 17 : Supply Voltage Rejection versus
Frequency (Stereo amplifier) C2 and C3 (Stereo amplifier)
Figure 18 : Supply Voltage Rejection versus Figure 19 : Gain versus Input Sensitivity
C2 and C3 (Stereo amplifier) (Stereo amplifier)
9/21
TDA2005
10/21
TDA2005
APPLICATION SUGGESTION
The recommended values of the components are those shown on Bridge applicatiion circuit of Figure 1.
Different values can be used ; the following table can help the designer.
Recom.
Comp. Purpose Larger Than Smaller Than
Value
R1 120 kΩ Optimization of the Output Smaller Po max Smaller P o max
Symmetry
R2 1kΩ
R3 2 kΩ
11/21
TDA2005
APPLICATION INFORMATION
Figure 23 : Bridge Amplifier without Boostrap
12/21
TDA2005
13/21
TDA2005
14/21
TDA2005
15/21
TDA2005
16/21
TDA2005
17/21
TDA2005
Loudspeaker Protection
The circuit offers loudspeaker protection during
short circuit for one wire to ground.
Polarity Inversion
High current (up to 10A) can be handled by the
device with no damage for a longer period than the
blow-out time of a quick 2A fuse (normally con-
nected in series with the supply). This feature is
added to avoid destruction, if during fitting to the
car, a mistake on the connection of the supply is
made.
18/21
TDA2005
Figure 37 : Maximum Allowable Power Dissipa- Figure 38 : Output Power and Drain Current ver-
tion versus Ambient Temperature sus Case Temperature
19/21
TDA2005
mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 5 0.197
B 2.65 0.104
C 1.6 0.063
D 1 0.039
E 0.49 0.55 0.019 0.022
F 0.88 0.95 0.035 0.037
G 1.45 1.7 1.95 0.057 0.067 0.077
G1 16.75 17 17.25 0.659 0.669 0.679
H1 19.6 0.772
H2 20.2 0.795
L 21.9 22.2 22.5 0.862 0.874 0.886
L1 21.7 22.1 22.5 0.854 0.87 0.886
L2 17.4 18.1 0.685 0.713
L3 17.25 17.5 17.75 0.679 0.689 0.699
L4 10.3 10.7 10.9 0.406 0.421 0.429
L7 2.65 2.9 0.104 0.114
M 4.25 4.55 4.85 0.167 0.179 0.191
M1 4.73 5.08 5.43 0.186 0.200 0.214
S 1.9 2.6 0.075 0.102
S1 1.9 2.6 0.075 0.102
Dia1 3.65 3.85 0.144 0.152
20/21
TDA2005
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectronics.
21/21