Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
REVISION HISTORY
Revision Date Notes
1 Initial Release.
TABLE OF CONTENTS
Revision History.................................................................................................................................. 2
List of Tables ....................................................................................................................................... 6
Table of Figures .................................................................................................................................. 6
Safety Information .............................................................................................................................. 7
Cautions and Warnings ....................................................................................................................... 7
Battery Safety Guidelines .................................................................................................................... 7
Introduction ......................................................................................................................................... 8
External Views..................................................................................................................................... 8
Main Exploded Views ........................................................................................................................ 10
Disassembly and Recovery ............................................................................................................. 13
Disassembly and Recovery Map....................................................................................................... 13
Tools Required for Disassembly ....................................................................................................... 14
SIM Tray Removal ............................................................................................................................ 16
Water Detection Label Inspection ..................................................................................................... 17
IMEI Label Removal .......................................................................................................................... 18
Battery Inlay Removal ....................................................................................................................... 19
Rear Cover Graphite Removal .......................................................................................................... 28
Rear Cover Removal ......................................................................................................................... 29
Water Detection Label Inspection ..................................................................................................... 30
Rear-Facing Camera Lens Removal ................................................................................................ 31
Flash Board Removal ........................................................................................................................ 32
Finger Print Sensor Flex Removal .................................................................................................... 33
TOF Grommet Removal .................................................................................................................... 34
Main PCB Removal ........................................................................................................................... 35
Front-Facing Camera Removal ......................................................................................................... 38
Rear-Facing Camera Removal ......................................................................................................... 39
Finger Print Sensor Foam Removal .................................................................................................. 40
Secondary MIC Foam Removal ........................................................................................................ 41
Audio Sealing Glue Removal ............................................................................................................ 42
Headset Jack Grommet Removal ..................................................................................................... 43
Copper Foil Removal ........................................................................................................................ 44
Speaker Box Removal ...................................................................................................................... 45
Sub Board Removal .......................................................................................................................... 46
Water Detection Label Inspection ..................................................................................................... 48
USB Grommet Removal .................................................................................................................... 49
Primary MIC Foam Removal ............................................................................................................. 50
Vibrator Removal .............................................................................................................................. 51
LIST OF TABLES
Table 1. External Views Parts List ........................................................................................................ 9
Table 2. Assembly Exploded View Parts List ..................................................................................... 10
TABLE OF FIGURES
Figure 1. External Views ....................................................................................................................... 8
Figure 2. Assembly Exploded View .................................................................................................... 10
SAFETY INFORMATION
Cautions and Warnings
Electrostatic Discharge
The phone components may be damaged by electrostatic discharge (ESD). Always use an ESD mat and ground strap
when working with internal components.
INTRODUCTION
External Views
Reference # Description
1 SIM Door
2 Housing Frame
3 Front Ring
4 LED
5 Receiver
6 Front-Facing Camera
7 P&L Sensor
8 Headset Jack
9 Main Lens
10 USB Port
11 Speaker Mesh
12 Volume Key
13 Power Key
14 Camera Lens
15 Camera Ring
16 Front-Facing Camera
17 TOF
18 Flash Lens
19 FPS Bezel
20 FPS
21 Battery Inlay
3 mm Allen Wrench --
Hot Plate --
Black Stick --
Torque Driver --
Shim 4-00-5L-10000
Philips Bit --
Plastic Tweezers -- --
ESD Mat -- --
Wrist Strap -- --
Gloves -- --
Inspect the WDL inside the SIM Tray Slot for signs of
activation. Use external light if needed.
NOTE
The Battery Inlay can be recovered
and reused after removal.
NOTE
Battery Inlay Removal Methods A and B have
the same preheating steps, as shown below.
// CAUTION //
Do not set the Hot Plate temperature higher than
80°C (176°F). Damage to the phone may occur.
NOTE
Preheating with an oven is also acceptable if the
oven is set to the same temperature.
// CAUTION //
Wear protective gloves when handling heated
phones.
NOTE
Perform the Battery Inlay removal procedure
before the phone starts to cool off.
//CAUTION//
Do not set the Heat Gun temperature higher than
80°C (176 °F). Damage to phone may occur.
//CAUTION//
Wear protective gloves while handling heated
phones.
12. Use the Heat Gun to warm the phone edges for
about 3 minutes. Keep the Heat Gun in motion
to avoid damaging the phone.
NOTE
Begin this step before the phone starts to cool
off.
// CAUTION //
Do not insert the Thin Plastic Spudger more
than 10 mm to prevent damaging internal
components.
//CAUTION//
Do not insert the Thin Plastic Spudger more than
10 mm to prevent damaging internal
components.
//CAUTION//
The highlighted frame on the left-hand side is a
weak area. Do not disassemble at this location.
NOTE
Be careful with the Finger Print Sensor Flex.
Vibrator Removal
NOTE
Remove the Vibrator only if necessary.
After you remove it, you cannot reuse it.
Battery Removal
/// WARNING /// // CAUTION //
Failure to adhere to Safety Critical Note(s) may Handle the Battery Pack with care. If dropped on the
increase risk of rupture, burning, or failure to floor, it may be internally damaged and must be
function safely when used by the customer. scrapped.
Refer to the Battery Safety Guidelines.
Ensure Battery and its insulation are not damaged (e.g.
scratched, dented, punctured) prior to and through
NOTE assembly.
Prior to assembly, ensure Battery edges and surfaces
Remove the Battery only if it is are not dented or deformed, and that fixtures and parts
defective or damaged. After you that will contact the Battery are free of foreign material.
remove it, you cannot reuse it.
Ensure screws and screwdrivers do not contact the
Battery.
// CAUTION //
Do not set the Hot Plate temperature higher than
80°C (176°F). Damage to the phone may occur.
NOTE
Preheating with an oven is also acceptable if the
oven is set to the same temperature.
PARTS REFRESH
Tools Required for Parts Refresh
The following tools are required for parts refresh of the Moto G8 Plus phone.
Black Stick --
ESD Mat -- --
Wrist Strap -- --
Isopropyl (ISP) Alcohol -- --
Cotton Swabs -- --
Cleaning Pads -- --
Gloves or Finger Collets -- --
ASSEMBLY
Assembly Map
Black Stick --
Torque Driver --
PH00 Bit --
Manual Roller --
18-gauge Needle
Plastic Tweezers -- --
Tweezers -- --
Gloves or Finger Collets -- --
Material P/N
NOTE
This procedure is only required when replacing the
Main PCB or Front Housing.
NOTE
The tip of the needle and Tweezers must be
cleaned after each application.
NOTE
Care not to exceed the diameter while applying
the Thermal gel.
A 4
B 5
C 3
NOTE
Needle must be replaced daily.
MGY-OSSG- https://www.coolermaster.com/catalog/coolers/thermal-grease/mastergel-pro/
N15M-R1
https://www.coolermaster.com/catalog/coolers/thermal-grease/mastergel-maker/
MGZ-NDSG-
N15M-R1
https://www.coolermaster.com/catalog/coolers/thermal-grease/ic-essential-e1/
RG-ICE1-TG15-
Cool Master R1
https://www.coolermaster.com/catalog/coolers/thermal-grease/ic-essential-e2/
RG-ICE2-TA15-
R1
https://www.coolermaster.com/catalog/coolers/thermal-grease/extreme-fusion-
RG-EFX1-
x1/
TG15-R1
Vibrator Assembly
Description Reference #
Doha FRU TP LCM Assy Blue
1
Doha FRU TP LCM Assy Berry
HQ20401195000+Motor_8x3.5_FPC_AH 15
NOTE
Make sure the Coax Cable A is placed above the
Coax Cable B.
NOTE
Be sure to align the white lines on the Link Flex
with the white lines on the Front Housing.
Battery Assembly
Description Reference #
Doha FRU TP LCM Assy Blue
1
Doha FRU TP LCM Assy Berry
ACCY,BAT,BAT,4000mAh,KD40;ATL466572;SWD; 14
NOTE
For each cycle roll the Manual Roller from top to
bottom of the Battery and vice versa.
NOTE
Each cycle should last for 3 seconds.
NOTE
Use care not to break the Finger Print Sensor
Flex.